FEC
MODEL FEC-150GMK (BLACK) OR FEC-150GMW (WHITE) WALL MOUNT
BRACKET KIT FOR USE WITH PANASONIC AW-UE150 CAMERA
WALL MOUNT BRACKET WITH GUSSETS
HEIGHT 6.40" WIDTH 8.73"
DEPTH 10.54"
1
STEP 1
ATTACH BRACKET
WITH (4) 8-32 X 1/4"
SCREWS
2
PANASONIC
1
(DO NOT USE EO BOX AS SOLE SUPPORT. WALL MOUNT BRACKET MUST BE SECURED WITH SUFFICIENT SIZE SCREWS
2
THROUGH THE .25" DIAMETER. MOUNTING HOLES.)
MOUNT BRACKET TO WALL USING APPROPRIATE HARDWARE THROUGH THE .25" MOUNTING HOLES.
USE 1/4 x 2 1/2" LAG BOLTS FOR WOOD WALL STUDS. ROUTE CABLES THROUGH WIRE MANAGEMENT PORTS.
3
(MAKE CERTAIN THAT MOUNTING METHOD IS SECURE AND FOLLOWS ACCEPTED NORMS FOR THIS APPLICATION)
4
MOUNT CAMERA TO TWIST-LOCK CAMERA BRACKET PER CAMERA INSTRUCTIONS
FINISH SECURING CAMERA TO MOUNTING PLATE WITH (1) SCREW SHIPPED WITH CAMERA
5
ALSO ATTACH DROP PREVENTION WIRE PER CAMERA INSTRUCTIONS.
6
FOR EXTRA SUPPORT ADD SIDE GUSSETS TO MOUNT WITH (4) 6-32 X 3/8" SCREWS EACH SIDE
STEP 2
AW-HE100 INS
MOUNT CAMERA TWIST LOCK PLATE TO BRACKET WITH (4) 8-32 X 1/4" SCREWS
AS AN OPTION, THE WALL BRACKET MAY ALSO BE ATTACHED TO A 1 GANG, 2GANG OR 4" SQUARE EO BOX.
HOLE SET FOR ATTACHING
TO 1 & 2 GANG EO BOXES
TRUCTIONS
STEP 3
3
LAG BOLT
4
STEP 4
PLACE CAMERA ON
MTG BRACKET &
TWIST TO LOCK
IN POSITION
NOTE: REFER
TO CAMERA
INSTRUCTIONS
THIS IS WHERE
DROP PREVENTION
WIRE ATTACHES
(SHIPS WITH CAMERA)
NOTE: THESE 1/4-20
SCREWS ONLY USED
TO SECURE CAMERA
WHEN
IS USED.
STEP 5 VIEW
5
BRACKET
NO
INSTALL 3MM SCREW
FLAT & LOCK WASHER
TO SECURE CAMERA
TO MOUNTING
BRACKET
(THIS HARDWARE
SHIPS WITH CAMERA)
HOLE SET FOR
ATTACHMENT TO
4" SQUARE EO BOX
STEP 6 VIEWS
6
"ATTACH SIDE GUSSETS
FOR ADDITIONAL STABILITY"
SAFETY NOTE:
- Before beginning the installation, it is very important to examine the unit for damage, defects and correct hardware.
- The Installation instructions must be read and entirely understood prior to install.
- It must be determined that the mounting surface is capable of supporting the mount and equipment.
- The Professional Installer must determine the proper way to attach the WALL BRACKET MODEL
- The installation of the mount and equipment is dependent on proper/secure attachment and is the responsibility of the installer.
- Make sure wall will support 4 times the combined weight of Equipment and Wall Mount.-
- This mount should be attached to wood studs only. Under no circumstances should this product be mounted to metal studs, unless an installation professional
deems they have been adequately reinforced and will support 4 times the combined weight of Equipment and the Wall Mount.
- Please use only the bolts supplied with the unit or bolts of the correct size, making sure the hardware used is tightened properly for a secure installation..
- The WALL BRACKET MODEL is only intended to be used with the equipment listed on the install sheet. It is not meant to be used with any other equipment.
- If at anytime, a question arises regarding this installation (or regarding the safety or integrity of the projected use) cease the installation
and either obtain the advice of another qualified installer or contact FEC.
FEC
GLEN COVE, NY 11542
5 BREWSTER ST.
PHONE: (516) 967-9565
fecrack@ix.netcom.com
XXXX
ATTACH GUSSETS
WITH 6-32 X 3/8"
SCREWS
HARDWARE:
(4) 1/4" X 2 1/2" HEX HEAD LAG BOLT
(4) 8-32 X 1/4" PHILLIPS PAN HEAD SCREW
(2) 1/4-20 X 1/4" SCREWS
(2) 1/4" LOCK WASHER
(8) 6-32 X 3/8" SCREWS
P/N 22645
12-18-18
01-24-20
02-07-20
C10-5024
03-04-20
Loading...