Panasonic Facsimile UF-590, UN-580, UF-580 Operating Instructions Manual

UF-590

Getting to Know

Your Machine

Installing Your

Machine

Programming

Your Machine

Basic OperationsAdvanced

Features

Network FeaturesPrintout Journals

and Lists

Problem Solving Appendix

Operating Instructions

Facsimile

Model No.

English

Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference.

(For Facsimile)

IMPORTANT INFORMATION

When requesting information, supplies or service always refer to the model and serial number of your machine. The model and serial number plate (Main Name Plate) is located on the machine as shown below. For your convenience, space is provided below to record information you may need in the future.

Model No.

Serial No.

Date of Purchase

Dealer

Address

Telephone Number () –

Supplies Telephone Number () –

Service Telephone Number () –

Model and Serial Number

The contents of this Operating Instructions are subject to change without notice.

Table of Contents

Safety Information.......................................................................................................... 7

Precaution....................................................................................................................... 9

Function Key................................................................................................................... 10

External View .................................................................................................................. 11

Control Panel .................................................................................................................. 12

Main Unit and Accessories............................................................................................ 14

Installing the Accessories ............................................................................................. 15

Installing the Toner Cartridge ....................................................................................... 16

Loading the Recording Paper ....................................................................................... 18

T How to Load the Recording Paper ................................................................. 18

Adjusting the Paper Cassette for the Paper Length ................................................... 20

T How to Adjust the Paper Cassette for the Paper Length................................ 20

Adjusting the Paper Cassette for the Paper Width ..................................................... 21

T How to Adjust the Paper Cassette for the Paper Width ................................. 21

Connecting the Telephone Line Cable and Power Cord............................................. 22

Setting the Dialling Method (Tone or Pulse)................................................................ 24

Adjusting the Volume .................................................................................................... 25

User Parameters............................................................................................................. 26

T General Description........................................................................................ 26

T Setting the Date and Time.............................................................................. 26

T Setting Your LOGO ........................................................................................ 27

T Setting Your Character ID .............................................................................. 28

T Setting Your ID Number (Fax Telephone Number) ........................................ 29

One-Touch/Abbreviated Dialling Numbers.................................................................. 30

T Entering One-Touch/Abbreviated Dialling Numbers ...................................... 30

T Editing One-Touch/Abbreviated Dialling Numbers......................................... 32

T Printing Out a Directory Sheet........................................................................ 34

Customizing Your Machine ........................................................................................... 35

T General Description........................................................................................ 35

T Setting the Fax Parameters........................................................................... 35

T Fax Parameter Table...................................................................................... 36

Loading Documents....................................................................................................... 40

T Documents You Can Send ............................................................................. 40

T Documents You Cannot Send ........................................................................ 40

T How to Load Documents ................................................................................ 41

Basic Transmission Settings ........................................................................................ 42

T General Description........................................................................................ 42

T Contrast.......................................................................................................... 42

T Resolution ...................................................................................................... 42

T Verification Stamp .......................................................................................... 43

T Communication Journal (COMM. JOURNAL) ............................................... 44

Getting to Know Your Machine

Installing Your Machine

Programming Your Machine

Basic Operations

Table of Contents

Sending Documents....................................................................................................... 45

T General Description ....................................................................................... 45

T Memory Transmission.................................................................................... 46

T Direct Transmission ....................................................................................... 52

T Voice Mode Transmission.............................................................................. 56

T Transmission Reservation ............................................................................. 58

T Redialling ....................................................................................................... 61

Receiving Documents.................................................................................................... 62

T Reception Modes ........................................................................................... 62

T Telephone Mode ............................................................................................ 63

T Fax / Tel Auto Switching Mode ...................................................................... 64

T Fax Mode ....................................................................................................... 65

T TAM (Telephone Answering Machine) Interface Mode.................................. 66

T Print Reduction .............................................................................................. 68

T Receiving Oversize Documents..................................................................... 69

T Substitute Memory Reception ........................................................................ 70

T Print Collation Mode....................................................................................... 70

Making Copies ............................................................................................................... 71

Timer Controlled Communications .............................................................................. 72

T General Description ....................................................................................... 72

T Deferred Transmission................................................................................... 72

T Deferred Polling ............................................................................................. 73

Polling ............................................................................................................................. 74

T General Description ....................................................................................... 74

T Setting the Polling Password ......................................................................... 74

T Preparing to be Polled ................................................................................... 75

T To Poll Documents from Another Station....................................................... 76

Program Keys ................................................................................................................. 77

T General Description ....................................................................................... 77

T Setting for Group Dialling ............................................................................... 77

T Setting for Deferred Transmission ................................................................. 78

T Setting for Deferred Polling............................................................................ 79

T Setting for Normal Polling .............................................................................. 80

T Setting for One-Touch Key ............................................................................ 81

T Changing or Erasing the Program Key Settings ............................................ 82

Edit File Mode ................................................................................................................. 83

T General Description ....................................................................................... 83

T Printing a File List .......................................................................................... 83

T Viewing the Contents of a File List................................................................. 84

T Changing the Start Time or the Station of a File ............................................ 85

T Deleting a File ................................................................................................ 87

T Printing Out a File .......................................................................................... 88

T Adding Documents into a File ........................................................................ 89

T Retry an Incomplete File ................................................................................ 90

Advanced Features

Table of Contents

Access Code................................................................................................................... 91

T General Description........................................................................................ 91

T Setting the Access Code ................................................................................ 91

T Operating Your Machine with the Access Code

(Restrict all operations) ................................................................................. 92

T Operating Your Machine with the Access Code

(Restrict access of Fax Parameters only) ...................................................... 92

Receive To Memory........................................................................................................ 93

T General Description........................................................................................ 93

T Setting the RCV To Memory Password.......................................................... 93

T Setting RCV To Memory ................................................................................ 93

T Printing Out Documents ................................................................................. 94

Distinctive Ring Detector (DRD) ................................................................................... 95

T General Description........................................................................................ 95

Fax Cover Sheet ............................................................................................................. 96

T General Description........................................................................................ 96

T To use the Fax Cover Sheet .......................................................................... 96

PIN Code Access............................................................................................................ 98

T General Description........................................................................................ 98

T Selecting the Access Method (Prefix or Suffix) .............................................. 98

T Dialling with a PIN Code................................................................................. 99

Fax Forward ....................................................................................................................100

T Setting Fax Forward ....................................................................................... 100

Selective Reception ....................................................................................................... 101

T General Description........................................................................................ 101

T Setting the Selective Reception. .................................................................... 101

Password Communications .......................................................................................... 102

T General Description........................................................................................ 102

T Compatibility with Other Machines ................................................................. 102

T Setting Password Transmission ..................................................................... 103

T Setting Password Reception .......................................................................... 104

T Using Password Transmission....................................................................... 105

T Using Password Reception ............................................................................ 106

Confidential Mailbox ...................................................................................................... 107

T General Description........................................................................................ 107

T Confidential Mailbox ....................................................................................... 107

T Sending a Confidential Document to a Remote Station's Mailbox ................. 108

T Polling a Confidential Document from a Remote Station's Mailbox ............... 109

T Receiving a Confidential Document to Your Machine's Mailbox .................... 110

T Storing a Confidential Document in Your Machine's Mailbox......................... 111

T Printing Out a Confidential Document from Your Machine's Mailbox............. 112

T Deleting a Confidential Document Stored in Your Machine's Mailbox ........... 113

Sub-addressing .............................................................................................................. 114

T General Description........................................................................................ 114

T To set the Sub-address into a One-Touch/ABBR. Dialling Numbers ............. 115

T To send a Document with Sub-address ......................................................... 116

Network Features

Table of Contents

Journals and Lists.......................................................................................................... 117

T General Description ....................................................................................... 117

T Transaction Journal ....................................................................................... 117

T Individual Transmission Journal (IND. XMT JOURNAL)................................ 118

T Communication Journal (COMM. JOURNAL)................................................ 121

T One-Touch/Abbreviated and Directory Search List ....................................... 123

T Program List................................................................................................... 126

T FAX Parameter List........................................................................................ 127

T Toner Cartridge Order Forms ........................................................................ 128

Troubleshooting ............................................................................................................. 129

T Information Codes.......................................................................................... 133

T Clearing a Recording Paper Jam ................................................................... 136

T Clearing a Document Jam ............................................................................. 137

T Cleaning the Document Scanning Area ......................................................... 138

T Cleaning the Printer Roller ............................................................................. 139

T Adjusting the Automatic Document Feeder (ADF) ......................................... 140

T Verification Stamp .......................................................................................... 141

T Checking the Telephone Line ........................................................................ 142

Specifications.................................................................................................................143

Recording Paper Specifications ................................................................................... 146

Options and Supplies .................................................................................................... 147

T Installing the Flash Memory Card .................................................................. 148

Regulatory Information.................................................................................................. 149

Glossary.......................................................................................................................... 152

ITU-T Image No. 1........................................................................................................... 155

Index ................................................................................................................................ 156

Printout Journals and Lists

Problem Solving

Appendix

Getting to Know

Your Machine

Getting to Know Your Machine

Safety Information

WARNING

denotes a potential hazard that could result in serious injury or death.

• TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.

• TO MINIMIZE THE POSSIBILITY OF SHOCK OR DAMAGE TO THE MACHINE, IT MUST BE PROPERLY EARTHED.

• THIS PRODUCT UTILIZES A LASER. ONLY QUALIFIED SERVICE PERSONNEL SHOULD ATTEMPT TO SERVICE THIS DEVICE DUE TO POSSIBLE EYE INJURY.

CAUTION

- USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

• THE MAINS PLUG ON THIS EQUIPMENT MUST BE USED TO DISCONNECT THE MAINS POWER. PLEASE ENSURE THAT THE SOCKET OUTLET IS INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.

• MAKE SURE THAT THE MACHINE IS INSTALLED IN A SPACIOUS OR WELL VENTILATED ROOM SO AS NOT TO INCREASE THE AMOUNT OF OZONE IN THE AIR. SINCE OZONE IS HEAVIER THAN AIR, IT IS RECOMMENDED THAT AIR AT FLOOR LEVEL BE VENTILATED.

Safety Information

CAUTION

denotes hazards that could result in minor injury or damage to the machine.

• TO REDUCE THE RISK OF SHOCK OR FIRE, USE ONLY NO. 26 AWG OR LARGER TELEPHONE LINE CABLE.

• DISCONNECT ALL POWER TO THE MACHINE BEFORE COVER(S) ARE REMOVED. REPLACE THE COVER(S) BEFORE THE UNIT IS RE-ENERGIZED.

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

• DO NOT USE THIS PRODUCT NEAR WATER, FOR EXAMPLE, NEAR A BATH TUB, WASH BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A WET BASEMENT OR NEAR A SWIMMING POOL.

• AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE) DURING AN ELECTRICAL STORM. THERE MAY BE A REMOTE RISK OF ELECTRIC SHOCK FROM LIGHTNING.

• DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE VICINITY OF THE LEAK.

• USE ONLY THE POWER CORD INDICATED IN THIS MANUAL.

IMPORTANT SAFETY INSTRUCTIONS

Getting to Know

Your Machine

Precaution

CAUTION

denotes hazards that could result in minor injury or damage to the machine.

Do not install the machine near heating or an air conditioning unit.

Avoid exposure to direct sunlight.

Install the machine on a flat surface, leave at least 4 inches (10 cm) of space between the machine and other objects.

Do not block the ventilation openings.

Do not place heavy objects or spill liquids on the machine.

Function Key

Any function can be started by first pressing and then enter the function number, or by

pressing or scroll key repeatedly until the desired function appears on the display.

FUNCTION

Deferred Communication

1 = XMT 2 = Polling

Polling

1 = Polling 2 = Polled

Print List

1 = Journal (Print/View) 2 = One-Touch/Abbreviated/Directory Search List 3 = Program List 4 = Fax Parameter List 5 = Not Used 6 = Individual XMT Journal 7 = Directory Sheet

Set Mode

1 = User Parameters

• Date & Time

• Logo

• Character ID

• ID Number (Fax Telephone Number) 2 = One-Touch/Abbreviated Numbers 3 = Program Keys 4 = Fax Parameters 5 - 7 = Not Used 8 = Maintenance

• Cleaning Printer Roller

• Toner Order Forms

Select Mode

1 = Communication Journal = OFF/ON/INC 2 = Not Used 3 = Cover Sheet = OFF/ON 4 = Password-XMT = OFF/ON 5 = RCV to Memory = OFF/ON 6 - 8 = Not Used 9 = Memory XMT = OFF/ON

Advanced Communication

1 = Not Used 2 = Confidential Communication

Edit File Mode

1 = File List (Print/View) 2 = Change Time/Station 3 = Delete File 4 = Print File 5 = Add Document 6 = Retry Incomplete File

Getting to Know

Your Machine

External View

NOTE

1. For some countries, the handset may not be available because of the country’s regulation or specification.

Recording Paper Sub Tray

Recording Paper Tray

Document Sub Tray

ADF Door

Control Panel

Document Return Tr ay

Printer Cover

Handset (Available as an option, see page 147)

Recording Paper Cassette (Standard)

250 sheets Recording Paper Cassette (Available as an option, see page 147)

Control Panel

- Used to enter a pause when entering or dialling a telephone number, or to redial the last dialled number.

- Used to start Abbreviated Dialling. (See pages 49 and 54)

- Used to separate the Sub-Address from the telephone number

- Used to start On-Hook Dialling. (See page 57)

- Used to switch the machine into energy saving mode. (See page 38)

- Used to set Normal, Lighter or Darker. (See page 42)

- Used to set Standard, Fine, Super-Fine or Halftone. (See page 42)

- Used to turn the verification stamp On or OFF. Lights when the verification stamp is set to ON.

- Blinks when the machine is transmitting a document or receiving.

- Lights when trouble occurs.

Keypad

- Used for manual number dialling, entering phone numbers, and numerical entries. Key

- Used to temporarily change the dialling mode to Tone when Pulse mode is set.

Control Panel

Getting to Know

Your Machine

- Press this button when you want to stop communication, registration operation, or audible tone.

- Used to make copies and set operations. (See page 71)

- Use this button when resetting all the previously set functions.

Used for the following:

- Start or select the function.

- Search for a station name. (See pages 50 and 55)

- Adjust the monitor and ringer volume. (See page 25)

- Move the cursor while entering numbers and characters.

- Search the station name for Directory Search Dialling.

- Confirm the entered station for multi-station communication.

- Confirm the current communication modes (e.g. Page number, ID, Dialled Telephone number, File number) when the unit is ON LINE.

One-Touch Keys (01-28)

- Used for One-Touch Dialling. (See pages 49 and 53) Program Keys (P1-P4)

- Used to enter long dialling procedures or Group Dialling Number keys. (See pages 77 to 82)

Character Keys

- The One-Touch Keys and Program Keys are serve as character and symbol input keys which are used to enter your LOGO, character ID and station name.

- Used to enter a symbol for LOGO, character ID and station name. Use or to select the symbols.

- Used to insert a space while entering LOGO, character ID and station name.

- Used to switch between upper and lower character set.

Installing Your Machine

Main Unit and Accessories

Unpack the carton and check that you have all the accessories illustrated.

NOTE

1. The shape of the telephone line cable and power cord may differ depending on each country’s regulation or specification.

2. The Telephone Line Cable Adapter is available in certain countries only.

Machine

Toner Cartridge Recording Paper Tray

Telephone Line Cable Power Cord

Operating Instructions

CD-ROM

Telephone Line Cable Adapter

(See Note)

Installing Your

Machine

Installing the Accessories

NOTE

1. For some countries, the handset may not be available because of the country’s regulation or specification.

Handset Cord

[Available as an Option

]

Handset

[Available as an Option]

Recording Paper Tray

Hook the projections into the square holes on the machine.

Final Installed View

Handset Cradle

[Available as an Option]

Hook the projections into the square holes on the machine. Connect the cable into the HANDSET jack on the machine.

Installing the Toner Cartridge

Unpack the Toner Cartridge and rock it back

and forth as shown for 5 or 6 times to even the

toner inside.

Remove the protective seal.

Note: Pull on the seal slowly and straight

out.

Open the Printer Cover.

Toner Cartridge

Printer Cover

Installing the Toner Cartridge

Installing Your

Machine

NOTE

1. Used toner cartridge should be disposed properly according to local regulations.

Align the projections on both sides of the

Toner Cartridge with the grooves in the

machine as shown and insert the Toner

Cartridge into the machine.

Note: Lock the Toner Cartridge into place

by pressing the handle down and then pushing towards the rear of the machine.

Close the Printer Cover.

If you are replacing the Toner Cartridge, it is

recommended to clean the Printer Roller to

maintain good printing quality. To clean the

Printer Roller, follow the procedure on page

139.

Printer Cover

Loading the Recording Paper

Paper Specifications

In general, most bond papers will produce excellent results. Most photocopy papers will also work very well. There are many "name" and "generic" brands of paper available. We recommend that you test various papers until you obtain the results you are looking for. For detailed recommended paper specifications,

(See page 146).

How to Load the Recording Paper

Lift up the Paper Cassette slightly and slide it

out from the machine.

Remove the Paper Cassette Cover.

1. Remove the Shipping Screw securing

the Pressure Plate.

2. Store the screw by attaching it to the post

provided under the Paper Cassette Cover for future use.

Paper Cassette

Cassette Cover

Shipping Screw

Loading the Recording Paper

How to Load the Recording Paper

Installing Your

Machine

1. Load the paper into the Paper Cassette.

Slide the paper width guide to the left until it lightly touches the stack of paper without bending the paper. The paper must fit squarely and firmly between the Paper Width Guide and the right side of tray. If it does not, the paper may feed into the printer incorrectly resulting in a paper jam.

Caution: Make sure that the paper is set

under the metal Paper Separation Clips and that it does not exceed the Maximum Paper Capacity Mark. You can load about 250 sheets (80g/m² lb weight). For paper specification, see page 146.

Re-install the Paper Cassette Cover.

Slide the Paper Cassette into the machine.

Paper

Width Guide

Max. Paper

Capacity Mark

Adjusting the Paper Cassette for the Paper Length

The factory default Paper Length setting for the Paper Cassette is on A4 size. To change the paper length to Letter or Legal size, follow the steps below.

NOTE

1. If you forget to change the Recording Paper Size setting in Fax Parameter No. 23 when

different paper is installed in the cassette, the unit will Stop printing after the 1st page of an Incoming Fax and display a "PAPER SIZE MISMATCH" error. Then, the Recording Paper Size setting automatically adjusts to the proper size and the unit resumes printing the Incoming Fax from the 1st page.

How to Adjust the Paper Cassette for the Paper Length

1. Remove the paper from the Paper

Cassette and place the cassette upside down on a flat surface.

2. While pushing down on the release latch,

pull out the Paper Length Guide.

3. Turn the Paper Cassette upright.

4. Insert the Paper Length Guide hooks into

the appropriate paper length slots (A4 or Legal) and slide the guide towards the back of the cassette until it locks in place.

5. Load the paper into the Paper Cassette.

Caution: Make sure that the paper is set

under the metal Paper Separation Clips and that it does not exceed the Maximum Paper Capacity Mark. You can load about 250 sheets (80g/m² lb weight). For paper specification, see page 146.

Replace the Paper Cassette Cover to the appropriate paper position (LTR, A4 or LGL).

Slide the Paper Cassette into the machine.

The Recording Paper Size setting of the Fax Parameter No. 23 must match the paper loaded in the cassette. If you change the Recording Paper Size, please change the setting accordingly.

(See page 37)

Paper Width Guide

Max. Paper

Capacity Mark

LGL

LTR

Paper Length Guide

Release Latch

Installing Your

Machine

Adjusting the Paper Cassette for the Paper Width

The factory default Paper Width setting for the Paper Cassette is on A4 size. To change the paper width to Letter/Legal size, follow the steps below.

NOTE

1. If you forget to change the Recording Paper Size setting in Fax Parameter No. 23 when different paper is installed in the cassette, the unit will Stop printing after the 1st page of an Incoming Fax and display a "PAPER SIZE MISMATCH" error. Then, the Recording Paper Size setting automatically adjusts to the proper size and the unit resumes printing the Incoming Fax from the 1st page.

How to Adjust the Paper Cassette for the Paper Width

1. Release the left Paper Separation Clip latch.

2. Pull up the Paper Separation Clip to remove it.

3. Reposition the Paper Separation Clip into the LTR/LGL slot.

4. Swing the Paper Separation Clip downward to latch it in place.

1. Load the paper into the Paper Cassette. Slide the paper width guide to the left until it lightly touches the stack of paper without bending the paper. The paper must fit squarely and firmly between the Paper Width Guide and the right side of tray. If it does not, the paper may feed into the printer incorrectly resulting in a paper jam.

Caution: Make sure that the paper is set

under the metal Paper Separation Clips and that it does not exceed the Maximum Paper Capacity Mark. You can load about 250 sheets (80g/m² lb weight). For paper specification, see page 146.

Replace the Paper Cassette Cover to the appropriate paper position (LTR, A4 or LGL).

Slide the Paper Cassette into the machine.

The Recording Paper Size setting of the Fax

Parameter No. 23 must match the paper

loaded in the cassette. If you change the

Recording Paper Size, please change the

setting accordingly.

(See page 37)

Paper Separation Clip

Max. Paper

Capacity Mark

LGL

LTR

Paper

Width Guide

Connecting the Telephone Line Cable and Power Cord

■ Power Cord

Plug the supply cord into the mains AC socket outlet. Connect the supply cord coupler into the mains supply inlet on the rear of the machine.

Warning: This apparatus must be properly earthed. Do not modify the AC outlet.

■ Telephone Line Cable

Plug one end of the telephone line cable into the telephone jack supplied by the telephone company and the other end into the LINE jack on the left side of the machine.

NOTE

1 Your machine uses little power and you should keep it ON at all times. If the power is turned

OFF for too long, the clock contents may be lost.

2. The shape of the telephone line cable and power cord may differ depending on each country’s regulation or specification.

3. The Telephone Line Cable Adapter is available in certain countries only.

Power Cord (Included)

Telephone Line Cable (Included)

Telephone Jack

Connecting the Telephone Line Cable and Power Cord

Installing Your

Machine

External Telephone (Optional)

You can connect an additional standard single line telephone to the machine. To connect the telephone, break off the protective tab on the TEL jack.

Telephone Line Cable Adapter

Setting the Dialling Method (Tone or Pulse)

Your machine can operate with either of two dialling methods (Tone or Pulse), depending on the type of telephone line you are connected to. If you need to change the dialling method to Tone or Pulse, follow the procedure below.

NOTE

1. For some countries, this feature is not available depending on the country’s regulation. The display may not show this feature.

SET MODE (1-8) ENTER NO. OR

∨∧

FAX PARAMETER(01-99)

NO.=

❚

06 DIALLING METHOD

2:TONE

for “PULSE“.

for “TONE“.

06 DIALLING METHOD

1:PULSE

06 DIALLING METHOD

2:TONE

Installing Your

Machine

Adjusting the Volume

You can adjust the monitor and ringer volume on your machine. The built-in speaker enables you to hear the dial tone, dialling signals, and busy tone. The ringer sounds when your machine receives a call.

NOTE

1. You can also adjust the volume of the key touch tone and the volume of the buzzer in the Fax Parameter No. 10 (KEY/BUZZER VOLUME). (See page 36)

Setting the Monitor Volume

You will hear the dial tone through the speaker.

* MONITOR *

❚

repeatedly to raise the volume.

repeatedly to lower the volume.

MONITOR VOLUME

LOW [

❚❚❚❚❚❚❚❚

]HIGH

MONITOR VOLUME

LOW [

]HIGH

Setting the Ringer Volume

Standby

12-NOV-2001 15:00

00%

repeatedly to raise the volume.

repeatedly to lower the volume.

RINGER VOLUME

((((

☎

))))

RINGER VOLUME

☎

User Parameters

Your facsimile machine has several basic settings (User Parameters) to help you keep records of the documents you send or receive. For example, the built-in clock keeps the current date and time, and your LOGO and ID Number help to identify you when you send or receive documents.

At standby the display will show the date and time. Once the standby display is set, it will automatically be updated.

General Description

Setting the Date and Time

SET MODE (1-8) ENTER NO. OR

∨∧

1:USER PARAMETERS? PRESS SET TO SELECT

DATE & TIME

❚

1-01-2001 00:00

Enter the new date and time.

Ex: Date : 12th

Month : November

Year : 2001

Time : 3:00 PM

If you make a mistake, use or to move the cursor over the incorrect number, then overwrite it with a correct one.

DATE & TIME

12-11-2001 15:00

1 2

1 1

2 0 0

1 5 0 0

User Parameters

Installing Your

Machine

When you send a document, your LOGO appears on the top of the copy printed out at the other station. The LOGO helps to identify you to someone who receives your document.

Setting Your LOGO

SET MODE (1-8) ENTER NO. OR

∨∧

1:USER PARAMETERS? PRESS SET TO SELECT

repeatedly until display shows;

LOGO

❚

Enter your LOGO (max. 25 characters and digits) by using the Character keys.

Ex:

If you make a mistake, use or to move the cursor

one space beyond the incorrect character, press then re-enter the new character.

If more than 19 characters are entered, the left side characters will scroll off the display.

LOGO PANASONIC

❚

A N A S O N I C

CLEAR

User Parameters

If the remote machine has a Character ID capabilities, when you are sending or receiving, your Character ID will appear on the remote machine's display and the remote machine's Character ID will appear on your display.

NOTE

1. The special characters of Å, Ä, Ö, Ü, Æ, è and é cannot be used for Character ID.

Setting Your Character ID

SET MODE (1-8) ENTER NO. OR

∨∧

1:USER PARAMETERS? PRESS SET TO SELECT

repeatedly until display shows;

CHARACTER ID

❚

Enter your Character ID (max. 16 characters and digits) by using the Character keys.

Ex:

If you make a mistake, use or to move the cursor

beyond the incorrect character, press then reenter the new character.

CHARACTER ID HEAD OFFICE

❚

E A D O F F I C E

CLEAR

User Parameters

Installing Your

Machine

If the remote machine does not have a Character ID but it has an ID Number, when sending or receiving, your ID Number will appear on the remote machine's display and their ID Number will appear on your display.

We suggest you use your facsimile telephone number as your ID number. (max. 20 digits)

NOTE

1. You may use to enter a "+" character at the beginning of the ID number to indicate the following digit(s) for your country code. Ex :+1 201 555 1212 +1 for U.S.A. country code.

+81 3 111 2345 +81 for Japan country code.

Setting Your ID Number (Fax Telephone Number)

SET MODE (1-8) ENTER NO. OR

∨∧

1:USER PARAMETERS? PRESS SET TO SELECT

repeatedly until display shows;

ID NO.

❚

Enter your ID (max. 20 digits) by using the keypad and

key to enter a space between numbers.

Ex:

If you make a mistake, use or to move the cursor

one space beyond the incorrect number, press then re-enter the new number.

ID NO. 201 555 1212

❚

2 0 1 5 5 5 1 2 1 2

CLEAR

Programming Your Machine

One-Touch/Abbreviated Dialling Numbers

One-Touch and Abbreviated Dialling are two fast ways of dialling full telephone numbers. To use these dialling methods, you must first store the telephone number using the following procedure.

Entering One-Touch/Abbreviated Dialling Numbers

To enter a One-Touch key, follow the steps below

SET MODE (1-8) ENTER NO. OR

∨∧

1:ONE-TOUCH 2:ABBR NO.

ONE-TOUCH< > PRESS ONE-TCH OR

∨ ∧

Ex:

<01> E

NTER TEL. NO.

Enter the telephone number (up to 36 digits including pauses and spaces).

Ex:

<01> 9-555 1234

❚

<01> ENTER NAME 9-555 1234

Enter the station name using character keys (up to 15 characters).

Ex:

<01> SALES DEPT

❚

9-555 1234

To record another number, repeat step 4 to 8.

To return to standby, press .

ONE-TOUCH< > PRESS ONE-TCH OR

∨ ∧

PAUSE

5 5 5 1 2

A L E S

E P TD

STOP

+ 128 hidden pages

Panasonic Facsimile UF-590, UN-580, UF-580 Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual