Panasonic ET-PKB80 User Manual

Attachment plate
ø49
81
(3-3/16˝)
178
(7˝)
370
(14-9/16˝)
117
(4-19/32˝)
374
70 (2-3/4˝)
110 (4-11/32˝)
140 (5-/12˝)
160 (6-5/16˝)
3-Ø9.5 (3/8˝)
Ø8.5 (11/32˝)
65
(2-9/16˝)
357–437 (14-1/16˝–17-7/32˝)
(Adjustable in 20 mm (25/32˝) steps)
150 (5-29/32˝)
130 (5-1/8˝)
100 (3-15/16˝)
20 (25/32˝)
Projector
ø43
(1-15/16˝)
(1-11/16˝)
S PEC F ILE
ET-PKB80
Ceiling mount bracket for high ceilings
As of August 2008 < 1 >
Specifications Vertical correction angle: +20°, -5°
Horizontal slant correction angle: ±10° Horizontal turn correction angle: ±5° Dimensions (W x H x D): 374 x 400 – 480 x 211 mm (14-23/32˝ x 15-3/4˝–18-29/32˝ x 8-5/16˝) Weight: 2.8 kg (6.2 lbs)
Attachment plateIllustration shows the ET-PKB80 attached to the projector.
Parts Attachment plate . . . . . . . . . . . . . . . . . . . . . . 1
Projector mount bracket . . . . . . . . . . . . . . . . 1
Adjuster pole A . . . . . . . . . . . . . . . . . . . . . . . 1
Adjuster pole B . . . . . . . . . . . . . . . . . . . . . . . 1
Angle adjuster A . . . . . . . . . . . . . . . . . . . . . . 1
Angle adjuster B . . . . . . . . . . . . . . . . . . . . . . 1
Holding bracket A . . . . . . . . . . . . . . . . . . . . . 1
Holding bracket B . . . . . . . . . . . . . . . . . . . . . 1
Washer-fitted hexagonal bolts (M6 x 12) . . . 19
Washer-fitted screws (M4 x 10) . . . . . . . . . . . 6
Wire rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Flat wire clip . . . . . . . . . . . . . . . . . . . . . . . . . 2
Clamp tube . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Weights and dimensions shown are approximate. Specifications subject to change without notice.
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
Dimensions
Description
This ceiling mount bracket is to be us ed when mounting LCD projectors to the ceiling.
Caution:
• All mounting work must be done by a qualified technician.
•Ensure that the mounting (ceiling) area has sufficient strength.
• Read the enclosed mounting ins tructions carefully before s tarting the mounting procedure.
• Do not use a power s crewdriver or impact screwdriver to tighten s crews. A torque s crewdriver or similar tool should be us ed.
• When the system is no longer to be us ed, have a qualified technician promptly remove and dispos e of it.
Loading...