Panasonic DVDS-42-PC, DVDS-422-PC Service manual

Specifications

Power supply:

Power consumption:

Power consumption in standby mode:

Dimensions: 16 15/16" (W) × 9 14/16" (D) × 1

Mass: 4.8lb (2.2 kg) (approx.)

Signal system: NTSC

Operating temperature range: + 5 to + 35 °C (+41 to +95°F)

Operating humidity range: 5 to 90 % RH (no condensation)

Discs played [8 cm (3") or 12 cm (5")]:

(1) DVD (DVD-Video, DivX,)

(2) DVD-RAM (DVD-VR, JPEG,, MPEG4,, DivX,, MP3,)

(3) DVD-R (DVD-Video, DVD-VR, JPEG,, MP3,, DivX,,

MPEG4

*5,7

)

(4) DVD-R DL (DVD-Video, DVD-VR)

(5) DVD-RW (DVD-Video, DVD-VR, JPEG,, MP3,,DivX,,

MPEG4

*5,7

)

(6) +R/+RW (Video)

(7) +R DL (Video)

(8) CD, CD-R / CD-RW (CD-DA, Video CD, SVCD , MP3,,

WMA,, JPEG,, MPEG4,, DivX,,

HighMAT Level 2 (Audio and Image))

*1 Conforming to IEC62107

*2 MPEG-1 Layer 3, MPEG-2 Layer 3

*3 Windows Media Audio Ver.9.0 L3

Not compatible with Multiple Bit Rate (MBR)

*4 Exif Ver2.1 JPEG Baseline files

Picture resolution: between 160 × 120 and 6144 × 4096 pixels (Sub sampling is 4:0:0, 4:2:0, 4:2:2 or 4:4:4)

Extremely long and slender pictures may not be displayed.

C120 V, 60 Hz

11 W

1 W (approx.)

11/16" (H)

430 (W) × 251 (D) × 43 (H) mm

7 7

DVD-S42PC DVD-S422PC

DL4.1 Mechanism Series

Color

(S).......................Silver Type

(K).......................Black Type (S42PC only)

*5 MPEG4 data recorded with the Panasonic SD multi cameras

or DVD video recorders conforming to SD VIDEO specifications (ASF standard) /MPEG4 (Simple Profile) video system/G.726 audio system

*6 Plays all versions of DivX®video (including DivX®6) with

standard playback of DivX®media files. Certified to the

DivX

Home Theater Profile.

GMC (Global Motion Compensation) not supported.

*7 The total combined maximum number of recognizable audio,

picture and video contents and groups: 4000 audio, picture and video contents and 400 groups.

ideo output:

Output level: 1 Vp-p (75 Ω )

Output terminal: Pin jack (1 system)

S video output:

Y output level: 1 Vp-p (75 Ω )

C output level: NTSC: 0.286 Vp-p (75 Ω )

Output terminal: S terminal (1 system)

Component video output:

[NTSC: (480)p/(480)i]

Y output level: 1 Vp-p (75 Ω )

PBoutput level: 0.7 Vp-p (75 Ω )

PRoutput level: 0.7 Vp-p (75 Ω )

Output terminal: Pin jack (Y: green, PB: blue,

ideo performance:

Horizontal resolution: More than 500 lines

Video S/N ratio: More than 65 dB

Audio output:

Output level: 2 Vrms (1 kHz, 0 dB)

ORDER NO.CHM0604021CE

DVD Player

: red) (1 system)

DVD-S42PC / DVD-S422P C

Output terminal: Pin jack

Number of terminals:

2 channel: 1 system

Audio performance:

(1) Frequency response:

l DVD (linear audio):

l CD audio:

(2) S / N ratio:

l CD audio:

(3) Dynamic range:

l DVD (linear audio):

l CD audio:

(4) Total harmonic distortion:

l CD audio:

Digital audio output:

Coaxial digital output: Pin jack

Pickup

Wave length: 662 nm / 785 nm

Laser power: CLASS 2 / CLASS 3A

Solder:

This model uses lead free solder (PbF).

4 Hz-22 kHz (48 kHz sampling)

4 Hz-44 kHz (96 kHz sampling)

4 Hz-20 kHz

115 dB

102 dB

98 dB

0.003 %

Note:

Specifications are subject to change without notice.

Mass and dimensions are approximate.

CONTENTS

Page Page

1 IMPORTANT SERVICE INFORMATION 4

1.1. Notes

1.2. About DivX

1.3. Manual for Customer

2 SAFETY PRECAUTIONS

2.1. GENERAL GUIDELINES

3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO

ELECTROSTATICALLY SENSITIVE (ES) DEVICES

4 PRECAUTION OF LASER DIODE

5 SERVICE CAUTION BASED ON LEGAL RESTRICTIONS

5.1. General description about Lead Free Solder (PbF)

6 PREVENTION OF STATIC ELECTRICITY DISCHARGE

6.1. Grounding for electrostatic breakdown prevention

6.2. Handling Precautions for Traverse Unit (Optical Pickup)

7 DISASSEMBLING THE CASING AND CHECKING P.C.B.S

7.1. Disassembly Procedure

7.2. Casing Parts and P.C.B. Positions

7.3. Top Panel

7.4. Front Panel

7.5. Operation P.C.B. and Power SW P.C.B.

7.6. Module P.C.B. 11

7.7. Mechanism Unit

7.8. Rear panel

7.9. Mother P.C.B.

7.10. Service Position

8 ASSEMBLING AND DISASSEMBLING THE MECHANISM UNIT

8.1. Disassembly Procedure

8.2. Traverse Unit

8.3. Tray

8.4. Loading section

8.5. Loading motor P.C.B.

8.6. Optical Pickup Unit

8.7. Traverse Motor

9 SELF-DIAGNOSIS FUNCTION AND SERVICE MODES

9.1. Optical Pickup Breakdown Diagnosis

9.2. Service Mode Table 1

9.3. DVD Self Diagnostic Function-Error Code

9.4. Last Error Code saved during NO PLAY

9.5. Service mode table 2

9.6. Sales demonstrat ion lock function 28

9.7. Handling After Completing Repairs

10 SERVICE PRECAUTIONS

10.1. Recovery after the dvd player is repaired

10.2. Firmware version-up of the DVD player

11 ADJUSTMENT PROCEDURES

11.1. Service Tools and Equipment

11.2. Important points in adjustment

11.3. Storing and Handling Test Discs

11.4. Optical adjustment

12 ABBREVIATIONS

13 VOLTAGE CHART

13.1. MOTHER P.C.B.

13.2. MODULE P.C.B.

14 BLOCK DIAGRAM

14.1. OVERALL BLOCK DIAGRAM

14.2. POWER SUPPLY BLOCK DIAGRAM

14.3. SERVO BLOCK DIAGRAM

14.4. VIDEO BLOCK DIAGRAM

14.5. AUDIO BLOCK DIAGRAM

15 INTERCONNECTION SCHEMATIC DIAGRAM & SCHEMATIC

DIAGRAM NOTES

15.1. INTERCONNECTION SCHEMATIC DIAGRAM

15.2. SCHEMATIC DIAGRAM NOTES

16 SCHEMATIC DIAGRAM

16.1. POWER SUPPLY SECTION (MOTHER P.C.B. (1 / 2))

SCHEMATIC DIAGRAM

16.2. FRONT & AV OUT SECTION (MOTHER P.C.B. (2 / 2))

SCHEMATIC DIAGRAM

16.3. MODULE SCHEMATIC DIAGRAM

17 PRINT CIRCUIT BOARD

17.1. MOTHER P.C.B.

17.2. MOTHER P.C.B. ADDRESS INFORMATION

17.3. MODULE P.C.B. (1/2)

17.4. MODULE P.C.B. (2/2)

17.5. MODULE P.C.B. ADDRESS INFORMATION

18 EXPLODED VIEWS

18.1. CASING PARTS & MECHANISM SECTION EXPLODED

VIEW

18.2. MECHANISM SECTION EXPLODED VIEW

18.3. PACKING & ACCESSORIES SECTION EXPLODED

VIEW

19 REPLACEMENT PARTS LIST

DVD-S42PC / DVD-S422P C

1 IMPORTANT SERVICE INFORMATION

1.1. Notes

When you replace EEPROM or exchange MODULE P.C.B., you have to take "Manual for customer" to the customer with unit.

(also in the case of unit exchange)

Please take and use "Manual for customer" from below.

1. Come with MODULE P.C.B. or EEPROM (Service part).

2. Make a photocopy section 1.3. "Manual for customer" on this service manual.

"Manual for customer" has important information for "DivX Video-on-Dem and Service" user.

Please don´t forget take it to the customer with unit!

1.2. About DivX

1.2.1. DivX

A video compression format developed by DivXNetworks, Inc. that compresses video files without any considerable loss of video quality.

1.2.2. About DivX Video-on-Demand Content

1.3. Manual for Customer

Warning for Customers Who Use the DivX Video-on-Demand content.

1. The registration code has been changed for the repair of the product or the product exchange.

2. Obtain and register a new registration code, otherwise you will no longer be able to play DivX Video-on-Demand content.

3. Follow the procedure on the DivX Video-on-Demand web site to register at http://vod.divx.com/.

DVD-S42PC / DVD-S422P C

* If you do not use the DivX Video-on-Demand content, please ignore this warning.

DVD-S42PC / DVD-S422P C

2 SAFETY PRECAUTIONS

2.1. GENERAL GUIDELINES

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

2.1.1. LEAKAGE CURRENT COLD

CHECK

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1MΩ and 5.2MΩ. When the exposed metal does not have a return path to the chassis, the reading must be

Figure 1

2.1.2. LEAKAGE CURRENT HOT CHECK (See Figure 1 .)

1. Plug the AC cord directly into the AC outlet. Do not use an

isolation transformer for this check.

2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF

capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more

sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the

voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the

above measurements.

6. The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD)

TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistorsand semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparableconductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installe d.

DVD-S42PC / DVD-S422P C

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handlin g unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficie nt todamage an ES device).

4 PRECAUTION OF LASER DIODE

DVD-S42PC / DVD-S422P C

5 SERVICE CAUTION BASED ON LEGAL RESTRICTIONS

5.1. General description about Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the normal solder.

Definition of PCB Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)

· The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The

letter of “PbF” is printed on the PCB using the lead free solder.)

· To put lead free solder, it should be well molten and mixed with the original lead free solder.

· Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

· Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt

the lead free solder.

· Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C

(662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

The following 3 types of lead free solder are available through the service parts route.

· RFKZ03D01K-----------(0.3mm 100g Reel)

· RFKZ06D01K-----------(0.6mm 100g Reel)

· RFKZ10D01K-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

DVD-S42PC / DVD-S422P C

6 PREVENTION OF STATIC ELECTRICITY DISCHARGE

The laser diode in the traverse unit (optical pickup) may brake down due to static electricity of clothes or human body. Use due caution to electrostatic breakdown when servicing and handling the laser diode.

6.1. Grounding for electrostatic breakdown prevention

Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electricity in the working environment. Proceed servicing works under the working environment where grounding works is completed.

6.1.1. Worktable grounding

1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet.

6.1.2. Human body grounding

1. Use the anti-static wrist strap to discharge the static electricity form your body.

6.1.3. Handling of optical pickup

1. To keep the good quality of the optical pickup maintenance parts during transportation and before installation, the both ends of the laser diode are short-circuited. After replacing the parts with new ones, remove the short circuit according to the correct procedure. (See this Technical Guide.)

2. Do not use a tester to check the laser diode for the optical pickup. Failure to do so will damage the laser diode due to the power supply in the tester.

6.2. Handling Precautions for Traverse Unit (Optical Pickup)

1. Do not give a considerable shock to the traverse unit (optical pickup) as it has an extremely high-precise structure.

2. When replacing the optical pickup, install the flexible cable and cut its short land with a nipper. See the optical pickup replacement procedure in this Technical Guide. Before replacing the traverse unit, remove the short pin for preventing static electricity and install a new unit. Connect the connector as short times as possible.

3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handlin g the cable.

4. The half-fixed resistor for laser power adjustment cannot be adjusted. Do not turn the resistor.

DVD-S42PC / DVD-S422P C

7 DISASSEMBLING THE CASING AND CHECKING P.C.B.S

7.1. Disassembly Procedure

7.2. Casing Parts and P.C.B. Positions

7.3. Top Panel

1. Unscrew the screws.

DVD-S42PC / DVD-S422P C

7.5. Operation P.C.B. and Power SW P.C.B.

1. Unscrew the screws.

7.6. Module P.C.B.

1. Remove the connectors.

2. Unscrew the screws.

3. Press each tab with the nipper to module PCB vertically.

7.4. Front Panel

1. Release the tabs and connector.

2. Release the tabs.

7.7. Mechanism Unit

1. Unscrew the screws.

DVD-S42PC / DVD-S422P C

2. Release the tabs.

7.8. Rear panel

1. Unscrew the screws.

2. Release the tabs.

7.9. Mother P.C.B.

1. Unscrew the screws.

7.10. Service Position

7.10.1. Servicing position of the Module P.C.B.

DVD-S42PC / DVD-S422P C

7.10.2. Servicing position of the Mother P.C.B.

7.10.3. List of the Extension Cables

DVD-S42PC / DVD-S422P C

8 ASSEMBLING AND

DISASSEMBLING THE MECHANISM UNIT

8.1. Disassembly Procedure

4. Remove the traverse unit.

8.2. Traverse Unit

1. Slide the lever (A) in the arrow direction (to the opposite side) till it stops.

2. Slide the lever (A) further by bending the tab at the right side of the lever (A) in the right direction. (The right groove opens and the boss becomes seen.)

3. Open the lever (B) to left. (The 2 grooves at the left side open.)

8.3. Tray

1. Slide the guide tray unit while pressing the stopper in the arrow direction, and remove the guide tray unit.

DVD-S42PC / DVD-S422P C

5. Remove the drive arm concave phase from the tray slider and tray.

2. Raise the loading unit.

3. Slide the lever in the arrow direction till it stops and pull the tray out.

1. Insert a part of the tray into the unit sliding over the groove on the mechanical chassis unit.

2. Insert the tray to the point before the tab of the mechanical chassis unit.

4. Spread the tabs at the both sides and pull the tray out. (The tray slides a little forward and stops.)

3. Hook the drive arm concave phase over the tray and the tray slider.

4. Press in the tray.

DVD-S42PC / DVD-S422P C

5. Make sure that the tray and the drive arm move smoothly.

4. Remove the belt.

5. Unlock the tab and remove the pulley.

6. Remove the relay gear.

8.4. Loading section

1. Spread the tabs at the both sides and push out the drive arm shaft.

7. Turn the change lever in the arrow direction till it stops.

8. Hook the change lever spring on the change lever project part temporarily.

2. Hook the lock lever spring on the lock lever projection part temporarily.

3. Unlock the tab and remove the lock lever.

9. Pull the lever (B) in the bottom side to your side and remove the change lever.

DVD-S42PC / DVD-S422P C

8.5. Loading motor P.C.B.

1. Unscrew the screws.

10. Remove the drive rack, the sub rack and the drive gear.

DVD-S42PC / DVD-S422P C

8.6. Optical Pickup Unit

8.6.1. Cautions to Be Taken in Handling the Optical Pickup Unit

The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body. Use due caution to electrostatic discharge damage when servicing the laser diode.

1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.

2. To prevent the laser diode from the electrostatic discharge damage, the Intermediate FFC of the optical pickup unit removed from the PCB should be short-circuited with a short pin or a clip.

3. The Intermediate FFC may be cut off if an excessive force is applied to it. Use caution when handling the Intermediate FFC.

4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the fIntermediate FFC, cut off the antistatic FPC.

8.6.2. Procedure for Disassembling the Optical Pickup Unit

1. Move the optical pickup unit in the arrow direction till it

stops.

DVD-S42PC / DVD-S422P C

4. Unscrew the screw.

5. Slide the shaft in the arrow direction.

2. Unscrew the screws.

3. Remove the drive rack.

6. Lift the optical pickup unit with the shaft.

7. Remove the optical pickup unit.

DVD-S42PC / DVD-S422P C

4. The intermediate FFC is fixed as shown below.

8. Pull the shaft and the rubber out.

1. Pass the intermediate FPC through the frame hole.

2. Align the guide section of the optical pickup unit with the rail.

3. Install the shaft top to the holder.

8.7. Traverse Motor

1. Unscrew the screws.

2. Remove the cover while lifting the inner gear.

3. Remove the solders.

DVD-S42PC / DVD-S422P C

4. Remove the traverse motor.

+ 46 hidden pages