Panasonic DVDLS-912-EG Service manual

ORDER NO.CHM0604024CE

Portable DVD/CD PLAYER

DVD-LS912EG

RAE1907Z-C Mechanism Series

Colour

(S).................Silver Type

Specifications

Operating temperature

range: +5 to +35°C (+41 to +95°F) Operating humidity range: 5-85% RH (no condensation) Region number: Region No.2 Discs played DVD (DVD-Video, DivX(*6,8)) [8cm (3”) or 12cm (5”)]: DVD-RAM (DVD-VR, JPEG(*4,6,7),

MP3(*2,6)) (MPEG4(*5,6),DivX(*6,8)) DVD-R (DVD-Video, DVD-VR,

JPEG(*4,6,7), MP3(*2,6)) (MPEG4(*5,6),DivX(*6,8))

DVD-R DL (DVD-Video, DVD-VR) DVD-RW (DVD-Video, DVD-

VR,JPEG(*4,6,7), MP3(*2,6) (MPEG4(*5,6),DivX(*6,8))

+R/RW (Video) +R DL (Video) CD, CD-R/RW [CD-DA, Video-CD,

SVCD(*1), MP3(*2, 6), WMA(*3, 6), JPEG (*4,6,7), MPEG4(*5,6), Divx(*6,8) HighMAT Level 2 (Audio and Image)]

*1: Conforming to IEC62107 *2: MPEG-1 Layer3, MPEG-2 Layer3

*3: Windows Media Audio Ver9.0 L3. Not compatible with Multiple Bit Rate (MBR)

*4: Exif Ver 2.1 JPEG Baseline files Picture resolution: between 160×120 and 6144×4096 pixels (sub sampling is 4:0:0, 4:2:2, 4:2:0 or 4:4:4)

*5: MPEG4 data recorded with the Panasonic SD multi cameras or DVD video recorders Conforming to SD VIDEO specifications (ASF standard)/MPEG4 (Simple Profile) video system/G.726 audio system

*6: The total combined maximum number of recognizalbe audio, picture and movie contents and groups: 4000 audio, picture and movie contents and 400 groups.

*7: Extremely long and slender pictures may not be displayed.

*8: Plays all versions of Divx® video (including DivX®6) with standard playback of DivX® media files.

Certified to the DivX Home Theater Profile.

DVD-LS912EG

GMC (Global Motion Compensation) is not supported.

Signal system: PAL/PAL60 (NTSC) selectable LCD screen: 9” -Si, TFT wide-screen LCD Composite-video

output/input:

Output/Input level: 1Vp-p (75W) Output/Input terminal: Mini-jack ( 3.5mm) Number of terminals: 1system (output/input selectable)

Audio output/input:

Output/input level: 1.5Vrms (1kHz, 0dB, 10kW) Output/input terminal: Stereo mini-jack ( 3.5mm) Number of terminals: 1system (output/input selectable)

Audio performance:

(1) Frequency response:

lDVD (linear audio): 4Hz-22kHz (48kHz sampling)

4Hz-44kHz (96kHz sampling)

lCD audio: 4Hz-20kHz

(2) S/N ratio:

lCD audio: 115dB

(3) Dynamic range:

lDVD (linear audio): 98dB lCD audio: 97dB

(4) Total harmonic distortion:

lCD audio: 0.008%

Digital audio output:

Optical digital output: Mini optical terminal Number of terminals: 1system

(also used for audio output/input)

Headphone output:

Output: Stereo mini-jack ( 3.5mm) Number of terminals: 2systems

Battery duration:

*CGR-H713: Option *Room temperature *using headphone

When brightness is set to “-5” while playing DVD: 6 hours (CGR-H712) /10 hours (CGR-H713)

When brightness is set to “0” while playing DVD: 4 hours (CGR-H712) /7 hours (CGR-H713)

When brightness is set to “+5” while playing DVD: 3 hours (CGR-H712) /5 hours (CGR-H713)

When LCD panel is off while DVD playing: 10 hours (CGR-H712) /15 hours (CGR-H713)

Battery recharge time (at 20°C)

8 hours (CGR-H712) /10 hours (CGR-H713)

Pickup:

Wave length: 662nm/ 785nm (DVD/CD) Laser power: CLASS 3B/ CLASS 3B (DVD/CD)

Power consumption in

0.3W

Standby mode (Using included AC adaptor): Power consumption in

13W

Recharge mode (Using included AC adaptor): AC adaptor:

Power source:

C 100-240V, 50/60Hz

Power consumption: 28W DC output: 12V, 1.5A

Car DC adaptor:

DC output: 12V 2A (Vehicle with 12V battery

only)

Battery pack CGR-H712 (lithium ion):

Voltage: 7.2V Capacity: 4500mAh

Dimensions (excluding protrusions and battery):

235.4(W) x 179.2(D) x 46.0(H) mm

/32”(W)x71/16”(D)x113/16”(H)]

24.3mm ( [D=185.0mm (7 [H=51.5mm (2

/64”) at lowest point

/32”) including battery]

Mass (including battery): approximately 1094g (38.59 oz)/

863g (30.44oz) (Without battery)

solder:

This model uses lead free solder (PbF).

Note

Specifications are subject to change without notice. Mass and dimensions are approximate.

Power supply: DC 12V (DC IN terminal) /

DC 7.2V (Exclusive battery terminal)

Power consumption

13W (Unit only: 10W)

(Using included AC adaptor):

DVD-LS912EG

CONTENTS

Page Page

1 Important Service Information 5

1.1. Notes

1.2. About DivX

1.3. Manual for Customer

2 SAFETY PRECAUTIONS

2.1. GENERAL GUIDELINES

3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO

ELECTROSTATICALLY SENSITIVE (ES) DEVICES 4 PRECAUTION OF LASER DIODE 5 HOW TO REPLACE THE LITHIUM BATTERY 6 Service caution based on legal restrictions

6.1. General description about Lead Free Solder (PbF)

7 HANDLING PRECAUTIONS FOR TRAVERSE DECK

5 5 6

7 8 9

7.1. Handling of optical pickup

7.2. Grounding for electrostatic breakdown prevention

8 DISASSEMBLY, REASSEMBLY AND SERVICE POSITION

8.1. Disassembly

8.2. P.C.B. location

8.3. Main cabinet of the unit

8.4. Traverse assembly

8.5. Optical pick-up unit

8.6. Disc motor

11 11

13 14 14 15 16 16

DVD-LS912EG

8.7. Main P.C.B. 17

8.8. Operation P.C.B.

8.9. Monitor assembly

8.10. Disc cover

8.11. Monitor cover

8.12. Mono arm

8.13. Inverter P.C.B.

8.14. LCD panel

8.15. Replacing the fuse in the car dc adaptor

8.16. Service position

9 SELF-DIAGNOSIS FUNCTION AND SERVICE MODE

9.1. Optical Pickup Breakdown Diagnosis

9.2. UHF displays

9.3. Service Mode Table 1

9.4. DVD Self Diagnostic Function-Error Code

9.5. Last Error Code saved during NO PLAY

9.6. Service mode table

9.7. Lens cleaning

10 SERV ICE PREC AUTIONS

10.1. Recovery after the dvd player is repaired

10.2. Firmware version-up of the DVD player

11 ADJUSTMENT PROCEDUR ES

11.1. Service Tools and Equipment

11.2. Important points in adjustment

11.3. Storing and Handling Test Discs

11.4. Optical adjustment

11.5. Electrical adjustment (LCD)

11.6. Electrical check (Video output check)

12 Abbreviation s 13 VOL TAGE CHART

13.1. MAIN P.C.B.

13.2. INVERTER P.C.B.

14 BLOCK DIAGRAM

14.1. OVERALL BLOCK DIAGRAM

14.2. POWER SUPPLY BLOCK DIAGRAM

14.3. SERVO BLOCK DIAGRAM

14.4. VIDEO BLOCK DIAGRAM

14.5. AUDIO BLOCK DIAGRAM

15 INTERCONN ECTIO N SCHEMATIC DIAGRAM & SCHEMATIC

17 17 18 18 19 20 20 20 21

22 23 24 24 26 26 28

29 29

30 30 30 31 33 34

35 37

37 40

41 42 43 44

DIAGRAM NOTES

15.1. INTERCONNECTION SCHEMATIC DIAGRAM

15.2. SCHEMATIC DIAGRAM NOTES

16 SCHE MATIC DIAGRAM

16.1. CHARGE BATTERY SECTION (MAIN P.C.B. (1/10)) SCHEMATIC DIAGRAM

16.2. POWER SUPPLY SECTION (MAIN P.C.B. (2/10)) SCHEMATIC DIAGRAM

16.3. SERVO SECTION (MAIN P.C.B. (3/10)) SCHEMATIC DIAGRAM

16.4. OPTICAL PICK UP SECTION (MAIN P.C.B. (4/10)) SCHEMATIC DIAGRAM

16.5. DV3 SECTION (MAIN P.C.B. (5/10)) SCHEMATIC DIAGRAM

16.6. VIDEO OUT SECTION (MAIN P.C.B. (6/10)) SCHEMATIC DIAGRAM

16.7. AUDIO OUT SECTION (MAIN P.C.B. (7/10)) SCHEMATIC DIAGRAM

16.8. OPERATION SECTION (MAIN P.C.B. (8/10)) SCHEMATIC DIAGRAM

16.9. LCD IF SECTION (MAIN P.C.B. (9/10)) SCHEMATIC DIAGRAM

16.10. XBS SECTION (MAIN P.C.B. (10/10)) SCHEMATIC DIAGRAM

16.11. OPERATION SECTION (OPERATION P.C.B.) SCHEMATIC DIAGRAM

16.12. INVERTER SECTION SCHEMATIC DIAGARAM

17 CIRC UIT BOARD ASSEMBLY

17.1. MAIN P.C.B. (1/2) (COMPONENT SIDE)

17.2. MAIN P.C.B. (2/2) (FOIL SIDE)

17.3. OPERATION & INVERTER P.C.B.

18 EXPL ODED VIEW S

18.1. Casing Parts & Mechanism Section Exploded View

18.2. Mechanism Section Exploded View

18.3. Packing & Accessories Exploded View

19 REPL ACEMENT PARTS LIST

47 48

59 60

61 62 63

65 66 67

DVD-LS912EG

1 Important Service Information

1.1. Notes

When you replace EEPROM or exchange MAIN P.C.B., you have to take “Manual for customer” to the customer with unit (also in the case of unit exchanges.).

Please take and use “Manual for customer” from below.

1. Come with MAIN P.C.B. or EEPROM (Service part).

2. Make a photocopy section 1.3 “Manual for customer” on this Service Manual.

“Manual for customer” has important information for “DivX Video-on-Demand Service” user. Please don’t forget take it to the customer with unit!

1.2. About DivX

1.2.1. DivX

A video compression format developed by DivXNetworks, Inc. that compresses video files without any considerable loss of video quality.

1.2.2. About DivX Video-on-Demand Content

DVD-LS912EG

1.3. Manual for Customer

Warning for Customers Who Use the DivX Video-on-Demand content.

1. The registration code has been changed for the repair of the product or the product exchange.

2. Obtain and register a new registration code, otherwise you will no longer be able to play DivX Video-on-Demand content.

3. Follow the procedure on the DivX Video-on-Demand web site to register at http://vod.divx.com/.

* If you do not use the DivX Video-on-Demand content, please ignore this warning.

DVD-LS912EG

2 SAFETY PRECAUTIONS

2.1. GENERAL GUIDELINES

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

2.1.1. LEAKAGE CURRENT COLD

CHECK

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1MW and 5.2MW .

When the exposed metal does not have a return path to

the chassis, the reading must be

2.1.2. LEAKAGE CURRENT HOT CHECK

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a 1.5kW, 10 watts resistor, inparallel with a 0.15µF capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the ACplug in the AC outletand repeat eachof the above measurements.

6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

3 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD)

TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typicalES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

DVD-LS912EG

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such asthe brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).

4 PRECAUTION OF LASER DIODE

5 HOW TO REPLACE THE LITHIUM BATTERY

This model is using a lithium battery for the remote control ass’y.

NOTE:

The lithium battery is a critical component. ( Type No.: CR2025 Manufactured by Panasonic. ) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use. Replacement batteries must be of the same type and manufacture. They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed. Do not attempt to re-charge the old battery or re-use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration.

DVD-LS912EG

6 Service caution based on legal restrictions

6.1. General description about Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86 F) more than that of the normal solder.

Definition of PCB Lead Free Solder being used

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder. (See right figure)

Service caution for repair work using Lead Free Solder (PbF)

- The lead free solder has to be used when repairing the equipment for which the lead free solder is used.(Definition: The letter of "PbF" is printed on the PCB using the lead free solder.)

- To put lead free solder, it should be well molten and mixed with the original lead free solder.

- Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

- Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the lead free solder.

- Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350+-30 degrees C (662+-86 F).

Recommended Lead Free Solder (Service Parts Route.)

- The following 3 types of lead free solder are available through the s ervice parts route. RFKZ03D01K-----------(0.3mm 100g Reel) RFKZ06D01K-----------(0.6mm 100g Reel) RFKZ10D01K-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

7 HANDLING PRECAUTIONS FOR TRAVERSE DECK

DVD-LS912EG

The laser diode in the optical pickup may break down due to potential difference caused by static electricity of clothes or human body.

So be careful of electrostatic break down during repair of the optical pickup.

It has already been adjusted.

7.1. Handling of optical pickup

1. Do not subject the optical pickup to static electricity as it is extremely sensitive to electrical shock.

2. To prevent the breakdown of the laser diode, an antistatic shorting pin is inserted into the flexible board (FPC Board). When removing or connecting the short pin, finish the job in as short times as possible.

3. Be careful not toapply excessivestress to theflexible board (FPC Board).

4. Do not turn the variable resistor (Laser power adjustment).

7.2. Grounding for electrostatic breakdown prevention

1. Human body grounding Use the antistatic wrist strap to discharge the static electricity from your body.

2. Work table grounding Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.

Caution

The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the optical pickup.

DVD-LS912EG

8 DISASSEMBLY, REASSEMBLY AND SERVICE POSITION

8.1. Disassembly

DVD-LS912EG

8.2. P.C.B. location

8.3. Main cabinet of the unit

Release the lock lever and remove the battery pack in the direction of the arrow.

1. Remove the 13 screws from the bottom of the unit.

2. Release the latches and remove the bottom cabinet.

8.4. Traverse assembly

8.4.1. Removing traverse assembly

1. Solder the 2 laser short lands on the flexible cable.

2. Unlock the connectors and remove the flexible cables.

DVD-LS912EG

8.4.2. Reinstalling traverse assembly

1. Reinstall the traverse assembly to the specified pin of the unit.

2. Reinstall the flexible cable of the optical pickpup unit and lock it securely.

3. Remove the solder of each laser short land of the flexible cable.

Caution:

Remove the solders completely: otherwise the laser diode won’temitlight.

4. Reinstall the spindle flexible cable as shown figure.

DVD-LS912EG

8.5. Optical pick-up unit

8.5.1. Removing optical pick-up unit

8.5.2. Reinstalling optical pick-up unit

The optical pick-up unit is factory adjusted. Do not touch the adjustment screw.

1. Reassemble the disassembled parts in the reverse order of disassembly.

2. When reinstalling the traverse assembly on the main unit after installing the optical pick-up unit, make sure to remove the s older from each of the two laser short lands on the flexible cable.

Caution:

· Remove the solders completely; otherwise the laser

· ·

diode won´t emit light.

· After replacing the optical pick-up unit, check the quality

· ·

of images played back and make optical adjustment.

8.6. Disc motor

8.6.1. Removing disc motor

1. Remove the adjustment screws A, B, and C.

2. Remove the disc motor.

Make sure that the traverse assembly removed before trying to remove the optical pick-up unit.

When removing the traverse assembly, solder the two laser short lands on the flexible cable of the optical pick-up unit.

1. Remove the two screws securing the main shaft retainer.

2. Remove the main shaft retainer.

3. Slide the main shaft in the direction indicated by the arrow to remove the optical pick-up unit.

8.6.2. Caution to be taken when replacing the disc motor

1. The mounting screws of the disc motor also serve as

adjustment screws. When reinstalling the disc motor, first turn the screws A, B, and C as far as they go by usual force to secure them (do not overtighten).

2. Back off the adjustment screws Aand C two complete turns

and secure them.

3. Back off the adjustment screw B one and a half turns and

secure them.

· This makes it nearly possible to play back disks and

· ·

adjust the jitter. Thereafter, adjust the adjustment screws C and A as

indicated.

8.7. Main P.C.B.

1. Unlock the connector and remove the flexible cable.

2. Remove the connector.

3. Remove the 4 screws and remove the main P.C.B..

DVD-LS912EG

8.9. Monitor assembly

1. Unlock the connector and remove the flexible cable.

2. Remove the 3 screws.

8.8. Operation P.C.B.

1. Remove the connector.

2. Remove the 6 screws and remove the operation P.C.B.

3. Release the latches and remove the hinge cover.

4. Remove the screw and remove the monitor assembly.

DVD-LS912EG

1. Roll the flexible cable as shown figure.

2. Install the monitor assembly on the cabinet.

8.11. Monitor cover

1. Remove the 5 screws

2. Remove the monitor cover into the direction of the arrow.

3. Unlock the connector and remove the flexible cable.

8.10. Disc cover

1. Remove the disc cover in order of (a) and (b).

Caution:

Please don’t lose the spring

Please do not nip the wire.

8.12. Mono arm

1. Remove the 2 screws.

2. Release the latches and remove the shaft covers.

3. Release the friction hinge from boss and remove the mono arm assembly.

DVD-LS912EG

5. Release the latches and remove the mono arm

6. Remove the plate.

4. Remove the 6 screws.

DVD-LS912EG

1. Roll the flexible cables as shown figure and install it to mono arm cover.

8.13. Inverter P.C.B.

1. Unlock the connector and remove the flexible cable.

2. Remove the connector and remove the inverter P.C.B.

8.14. LCD panel

2. Install mono arm.

3. Roll 3 turns of the flexible cable and Install the shaft cover (R) to flexible cable.

4. Pass the flexible cable and the friction hinge into the holes in the monitor cover.

5. Install the shaft covers to monitor cover.

1. Remove the LCD panel into the direction of the arrow.

8.15. Replacing the fuse in the car dc adaptor

· Replace only with the specified 125V/250V, 3A fuse. Use of

· ·

any other type can cause fire.

DVD-LS912EG

8.16. Service position

8.16.1. Board checks

1. Connect the main P.C.B and the traverse assembly with an extension cable.

2. Install the traverse assembly to the tilt adjustment jig using three screws and three washers.

Caution:

· Remove the rubber cushion from the traverse assembly to prevent it from getting damaged.

· ·

3. Install a dick on the traverse assembly.

Caution:

· Make sure the disk is securely installed on the disk motor.

· ·

4. Remove the main P.C.B., operation P.C.B., inverter P.C.B., and LCD panel as shown below.

5. The disk cannot be played back with the disk cover removed. Press and hold down the S5201 and S5202. (Secure with cellulose tape.)

DVD-LS912EG

9 SELF-DIAGNOSIS FUNCTION AND SERVICE MODE

9.1. Optical Pickup Breakdown Diagnosis

As a new feature, this unit has an “optical pick-up problem diagnosis function” and “a tilt adjustment confirmation function” built in. Use the following procedure to efficiently determine the problem and adjust tilt.If "NO DISC" is displayed, before exchanging the optical pick-up, carry out problem diagnosis first. If the present laser driving current is over 55, the optical pick-up may need to be exchanged.

Note:

Carry out diagnosis within 3 minutes of turning the unit on. (The player’s current can increase as it warms up, so turn the unit off and allow it to cool down before diagnosis.)

Cautions to be taken when replacing the optical pickup

The optical pickup may break down due to the static electricity of human body. Take proper protection measures against static electricity before repairing the parts around the optical pickup. (See the page describing the PREVENTION OF STATIC ELECTRICITY DISCHARGE.)

1. Do not touch the areas around the laser diode and

actuator.

2. Do not judge the laser diode with a tester. (The tester

will be damaged easily.)

3. It is recommended to use a destaticized soldering iron

DVD-LS912EG

for short-circuiting or removing the laser diode. (Recommended soldering iron) HAKKO ESD Product

4. Solder the land of the flexible cable in the optical pickup.

Note:

· When using a soldering iron which is not

· ·

destaticized, short-circuit the terminal face of the flexible case with a clip. After that, short-circuit the land.

· After the repairing work iscompleted, remove the

· ·

solder according to the correct procedure shown in this Technical Guide.

9.2. UHF displays

Use the internal service mode for evaluation of malfunctions.

Display Method Display Diagnosis

Items displayed when in use CHECK THE

Press the "0" button on the remote control while holding down the PAUSE and PLAY buttons on the player. The last error code generated is saved in the EEPROM

DISC H01 Inner cover trouble H02 Spindle servo error H03 Traverse error H04 Tracking servo error H05 Seek error F0** Disc format error F1** Disc code error F2** Decoder LSI error F5** DSC F6** ECC error F7** Microcomputer error F8** Microcomputer error

Focus error

+ 53 hidden pages