Panasonic DMW-FL360, DMW-FL360PP, DMW-FL360E, DMW-FL360GK Service Manual

ORDER NO. DSC0609033CE

Model No.DMW-FL360PP

DMW-FL360E DMW-FL360GK

B26

Flash

DMW-FL360PP / DMW-FL360E / DMW-FL360GK

CONTENTS

Page Page

1 INTRODUCTION 3

1.1. INTRODUCTION

1.2. IMPORTANT NOTICE

2 SAFETY PRECAUTIONS

2.1. GENERAL GUIDELINES

2.2. LEAKAGE CURRENT COLD CHECK

2.3. LEAKAGE CURRENT HOT CHECK (See Figure 1.)

3 OPERATING GUIDE

4 OPERATING INFORMATION

5 HOW TO DISCHARGE THE FLASH CHARGING CAPACITOR

6 SERVICE FIXTURE & TOOLS

6.1. SERVICE FIXTURE & TOOLS

7 ELECTRICAL ADJUSTMENT

7.1. AFTER REPLACING

8 DISASSEMBLY AND ASSEMBLY INSTRUCTIONS

8.1. DISASSEMBLY FLOW CHART

8.2. PCB LOCATION

8.3. DISASSEMBLY PROCEDURE

9 WIRING CONNECTION DIAGRAM

10 EXPLODED VIEWS

10.1. FRAME & CASING SECTION

10.2. PACKING PARTS & ACCESSORIES SECTION

11 REPLACEMENT PARTS LIST

11.1. MECHANICAL REPLACEMENT PARTS LIST

DMW-FL360PP / DMW-FL360E / DMW-FL360GK

1 INTRODUCTION

1.1. INTRODUCTION

This service manual contains technical information, which allow service personnel’s to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified , the information will be followed by service manual to be controlled with original service manual.

1.2. IMPORTANT NOTICE

1. The Electric components on the PCB (Printed Circuit Boad) are not supplied.

There fore, this Service Manual does not contain the PCB Layout, Schematic Diagram and replamenent parts list for Electric components on the P.C.B.s.

2. Also, please confirm the following notice for replacement parts.

a. The "CPU P.C.B." is supplied as "REAR CASE UNIT".

b. The "HOT SHOE P.C.B." is supplied as "HOT SHOE UNIT".

c. The "BOUNCE (V) P.C.B." includes "BOUNCE (H) P.C.B.".

DMW-FL360PP / DMW-FL360E / DMW-FL360GK

2 SAFETY PRECAUTIONS

2.1. GENERAL GUIDELINES

1. IMPORTANT SAFETY NOTICE

There are special compon ents used in this equipment which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify the original design without permission of manufacturer.

2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

2.3. LEAKAGE CURRENT HOT CHECK (See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use an

isolation transformer for this check.

2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 µF

capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallic part, and measure the

voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the

above measure ments.

6. The potential at any point should not exceed 0.75 V RMS.

A leakage current tester (Simpso n Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

2.2. LEAKAGE CURRENT COLD CHECK

1. Unplug the AC cord and connect a jumper between the two

prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between

the jumpere d AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1

MΩ and 5.2 MΩ. When the exposed metal does not have a

return path to the chassis, the reading must be infinity.

Figure. 1

3 OPERATING GUIDE

DMW-FL360PP / DMW-FL360E / DMW-FL360GK

4 OPERATING INFORMATION

DMW-FL360PP / DMW-FL360E / DMW-FL360GK

+ 21 hidden pages