Panasonic CT-32G14, CT-27G14 Owner’s Manual

just slightly ahead of our

Your new TV Monitor/Receiver features a solid
state chassis that is designed to give you many

years of enjoyment. It was thoroughly tested and
tuned at the factory for best pedormance.

Customer Record

The model and serial number of this product may

be found on the back of the unit. You shouldnote
the modeland sedal numberinthe space provided

and retain as a permanent record of your
purchase. This willaidinidentificationinthe event
of theftor loss.

Productregistrationisavailablefor U.S.customersat:

www.prodreg.oom/panasonlc

Model
Number

Serial
Number

Care
and Cleaning

Screen (Turn TV Off)

Use a mild soap solution or window
cleaner with a softclean cloth. DO NOT

USE ABRASIVE CLEANERS.

Avoid excessive moisture and wipe dry.

Cabinet and Remote Control

Use a softcloth dampened withwater or
a mild detergent solution. Do not use

benzene, thinner, or other petroleum
based cleaners.

Wipe dry with a soft clean cloth. Avoid

excessivemoisture.

Specifications

Power Source

CT-I 3R4 CT-20G24

CT-13R30 CT-20G34 120V AC,
CT-13R40 CT-20R16 60Hz _
CT-2_4 CT-2013S

CT-20G14

Channel Capability - 181 UHF-56;

Video Input Jacks 75 _o_p_,

(some models) PhonoJack

Audio Input Jacks 500mV RMS

(somemodels) 47K Ohm

VHF.12;

Cable-113

1V ,

Type

Television Location

This unit is intended to be used with an optiona
stand or entertainmentcenter. Consult yourdeale=
for available options.

[] Avoid excessive sunlight or bright lights

includingreflections.

C3 Keep away from excessive heat or moisture

Inadequate ventilation may cause interna
componentfailure.

[] Fluorescent lighting may reduce Remote

Controltransmittingrange.

[] Avoid magneticequipment, includingmotors

fans, or external speakers.

Optional Cable Connections

Shielded audio and video cables should be use(
between components. For best results:

Use75-ohro co_yJ_atshielded cabtes.

• . Use appropriate input and output
connectorsthat match your component

connectors,

Avoid long cables to minimize
interference.

AC Power Supply Cord

CAUTION: TO PREVENT

ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO
WIDE SLOT OF AC OUTLET Potadzedplug

AND FULLY INSERT. DO
NOT USE A PLUG WITH A

RECEPTACLE OR OTHER Non-Polarizedplug
OUTLET UNLESS THE

BLADE CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE, FOR SOME MODELS THAi"

ARE NON-POLARIZED, THE USE OF AN AC
ADAPTOR CONNECTOR MAYBE NECESSARY.

Batteries

Replace batteries inpairs.
Do not mix battery types (zinc carbon

withalkaline).
Do not recharge, shod-cimuit,

disassemble, heat, or bum use€
battedes.

Cable / Antenna

For proper reception, either a cable or antenna

connectLonare required.

Cable Connection

Connect the cable supplied by your local
cable company.

Incoming Cable from Cable Company

To Audio AMP Jack 0-2,0V RMS

(somemodels) 4.7K Ohm

Specificationsare subject to change withoutnotice
or obligation.

-2-

Note:

75OhmsVHFAJHF

onbackofTV

A cable converterbox may be required

for proper reception. Check with your
local Cable company for compatibility

requirements.

Antenna Connection

For proper reception of VHF/UHF
channels, an externalantenna is required.
For best reception an outdoor antenna is
recommended.

Antenna Mode must be set to TV.

VHF/UHF Antenna

A VHF/UHF antenna and transformer are supplied
in _g_. Attach to the TV, adjust the
antenna until the picture is clear, (See Antenna
Connection),

InGomlng Cable from Home Antenna

Helpful Hints" CablePreset 1

CableModeispresetatthefactory._ntenna users

mustchangeto AntennaModeintheSetUpMenu.|

Optional Equipment
Connections

VCRs, video disc players, video game equipment,
and DSS equipment can also be connected to the

antenna input connection. (See your equipment

manual).

Procedure

f. Connect equipment as shown to front or

rear Audio/Videoinputjacks.

Note: Front and rear Audio/Video

connections cannot be

2,

Select the Video mode by pressing TV/
VIDEO button.

3.

Operate optional equipment as instructed

inequipment manual.

Note: ff both S-VIDEO and VIDEO input are

used at the same time, two image will
appear on the TV screen.

operated at the same time.

To Audio Amplifier (AMP, some

models)

Connect to an external audio amplifier input for

listeningto sound from a stereo system.

Note: TO AUDIO AMP terminalscannotbe used

directlyfor externalspeakers.

Audio Adjustments

1. Press TV SPEAKERS ON button located

backof set.

Note: If your TV does not have a TV

SPEAKERS ON/OFF button,
select TV SPEAKERS ON from

AUDIO menu.

2. Set amplifiervolume to minimum,

3. A_fus'tTV vo_ume'_odesire_ _eveL
4, Adjustamplifiervolume to matchthe TV.

5. Press'iV SPEAKERS OFF buttonlocated

or_beck of set.

Note: ff your TV does not have a TV

SPEAKERS ON/OFF button,

select OFF&VAO from AUDIO

menu.

6. Volume and mute are now selected using
the TV controls.

Note: in OFF&FAO the volume is controlledby

the external amplifie_

Terminals on back of TV (some models) VCF_or Vit:h_oD_sc

-3-