Panasonic CS-E22JKK-1, CU-E18JKK-1, CS-E9JKKW-1, CU-E9JKK-1, CU-E22JKK-1 User Manual

...
QUICK GUIDE
Operating Instructions
Air Conditioner
Model No. Indoor Unit Single Split
Outdoor Unit CS-E9JKKW-1 CU-E9JKK-1 CS-E12JKKW-1 CU-E12JKK-1 CS-E18JKK-1 CU-E18JKK-1 CS-E22JKK-1 CU-E22JKK-1
Multi Split Outdoor Unit
CU-2E18JBK-1
Before operating the unit, read these operating instructions thoroughly and keep them for future reference.
QUICK GUIDE
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2010. Unauthorized copying and distribution is a violation of law.
F567672
WARNING
CAUTION
WARNING
Thank you for purchasing
TABLE OF CONTENTS
NOTE
OPERATION CONDITION
Panasonic Air Conditioner
TABLE OF CONTENTS

SAFETY PRECAUTIONS

MULTI AIR CONDITIONER SYSTEM
INDOOR UNIT
REMOTE CONTROL
2~3
6~7
SAFETY PRECAUTIONS
To prevent personal injury, injury to others, or property damage, please comply with the following. Incorrect operation due to failure to follow instructions below may cause harm or damage, the seriousness of which is classifi ed as below:
WARNING
CAUTION
4
The instructions to be followed are classifi ed by the following symbols:
5
This sign warns of death or serious injury.
This sign warns of injury or damage to property.
This symbol denotes an action that is PROHIBITED.
These symbols denote an actions that is COMPULSORY.
TROUBLESHOOTING
INFORMATION
QUICK GUIDE
BACK COVER
NOTE
The illustrations in this manual are for explanation purposes only and may differ from the actual unit. It is subjected to change without notice for future improvement.
OPERATION CONDITION
Use this air conditioner under the following temperature range
Temperature (°F)
COOLING
HEATING
Max. 89.6 73.4
Min. 60.8 51.8
Max. 86.0 -
Min. 60.8 -
Temperature (°F)
COOLING
HEATING
Max. 109.4 78.8
Min. 60.8 51.8
Max. 75.2 64.4
Min. 5.0 3.2
* DBT: Dry bulb temperature * WBT: Wet bulb temperature
2
8
9
Indoor
*DBT *WBT
Outdoor
*DBT *WBT
WARNING
INDOOR UNIT AND OUTDOOR UNIT
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Please consult authorized dealer or specialist to repair, install, remove and reinstall the unit. Improper installation and handling will cause leakage, electric shock or fi re.
Do not install the unit in a potentially explosive or fl ammable atmosphere. Failure to do so could result in fi re.
Do not insert your fi ngers or other objects into the air conditioner indoor or outdoor unit, rotating parts may cause injury.
Do not touch the outdoor unit during lightning, it may cause electric shock.
REMOTE CONTROL
Do not allow infants and small children to play with the remote control to prevent them from accidentally swallowing the batteries.
CAUTION
Air Inlet
Air Outlet
Air Outlet
Air Inlet
Air Inlet
WARNING
Examples of abnormality/ failure
WARNING
POWER SUPPLY
Do not use modifi ed cord, joint cord, extension cord or unspecifi ed cord to prevent overheating and fi re.
Do not share the same power outlet with other equipment to prevent overheating and fi re.
Do not operate with wet hands to prevent electric shock.
If the supply cord is damage, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a hazard.
It is strongly recommended to be installed with Earth Leakage Circuit Breaker (ELCB) or Residual Current Device (RCD) to prevent electric shock or fi re.
This equipment must be earthed to prevent electrical shock or fi re.
Prevent electric shock by switching off the power supply when:
- Before cleaning or servicing.
- Extended non-use.
- Abnormally strong lightning activity.
Stop using the product when any abnormality/failure occurs and disconnect the power plug or turn off the power switch and breaker. (Risk of smoke/fi re/electric shock)
• The ELCB trips frequently.
• Burning smell is observed.
• Abnormal noise or vibration of the unit is observed.
Examples of abnormality/ failure
• Water leaks from the indoor unit.
• Power cord or plug becomes abnormally hot.
• Fan speed cannot be controlled.
• The unit stops running immediately even if it is switched on for operation.
• The fan does not stop even if the operation is stopped.
Contact immediately your local dealer for maintenance/repair.
CAUTION
INDOOR UNIT AND OUTDOOR UNIT
Do not wash the indoor unit with water, benzene, thinner or scouring powder.
Do not use for other purpose such as preservation of food.
Do not use any combustible equipment in front of the airfl ow outlet to avoid fi re.
Do not expose yourself directly to cold air for a long period.
Do not sit or step on the unit, you may fall down accidentally.
Do not touch the sharp aluminium fi n, sharp parts may cause injury.
Do not switch ON the indoor unit when waxing the fl oor. After waxing, aerate the room properly before operating the unit.
Do not install the unit in oily and smoky areas. Ensure drainage pipe is connected properly.
Otherwise, leakage may occur. Aerate the room regularly. After long period of use, make sure the
installation rack is not deteriorate to prevent the unit from falling down.
REMOTE CONTROL
Do not use rechargeable (Ni-Cd) batteries. It may damage the remote control.
Remove the batteries if the unit is not going to be used for a long period of time.
New batteries of the same type must be inserted following the polarity stated to prevent malfunction of the remote control.
Indoor
Remote
Unit
Control
Air Outlet
Air Inlet
Power
Supply
Outdoor
Unit
Air Inlet
Air Inlet
Air Outlet
3

MULTI AIR CONDITIONER SYSTEM

Living room
Multi Split Outdoor Unit
INDOOR UNIT
Bedroom
POWER SUPPLY
Multi Split Outdoor Unit
(CU-2E18JBK-1)
DEFINITION
Multi air conditioner systems save space by letting you connect multiple indoor units to a single outdoor unit.
INDOOR UNIT
• It is possible to operate the indoor units individually or simultaneously. The operation mode priority is given to the fi rst unit that turned on.
• During operation, heating and cooling mode could not be activated at the same time for different indoor unit. The power indicator blinks to indicate the indoor unit is standing by for different operation mode.
Living room
POWER SUPPLY
Single Split System
Multi Split System
4
Bedroom
Models Number
CS-E9JKKW-1 / CU-E9JKK-1 15 Amps CS-E12JKKW-1 / CU-E12JKK-1 15 Amps CS-E18JKK-1 / CU-E18JKK-1 20 Amps CS-E22JKK-1 / CU-E22JKK-1 25 Amps CS-E9JKKW-1, CS-E9JKKW-1 / CU-2E18JBK-1
CS-E12JKKW-1, CS-E12JKKW-1 / CU-2E18JBK-1
Time Delay Circuit
Breaker
25 Amps 208/230VCS-E9JKKW-1, CS-E12JKKW-1 / CU-2E18JBK-1
Multi Split Outdoor Unit
Rated Volts
208/230V

INDOOR UNIT

CLEANING INSTRUCTIONS
HINT
Switch off the power supply before cleaning.
CAUTION
CLEANING INSTRUCTIONS
• Do not use benzene, thinner or scouring powder.
• Use only soap (
• Do not use water hotter than 104°F.
Do not touch the aluminium n, sharp parts may cause injury.
pH7) or neutral household detergent.
HINT
• To ensure optimal performance of the unit, cleaning maintenance has to be carried out at regular intervals. Dirty unit may cause a malfunction and you may see error code “H99”. Please consult authorized dealer.
2
8
5 6
1
INDOOR UNIT
• Wipe the unit gently with a soft, dry cloth.
2
FRONT PANEL
Remove Front Panel
• Raise and pull to remove the front panel.
• Wash gently and dry.
Close Front Panel
• Press down both ends of the front panel to close it securely.
3
REMOTE CONTROL RECEIVER
4
ALUMINIUM FIN
5
HORIZONTAL AIRFLOW DIRECTION LOUVER
E9JKKW-1, E12JKKW-1
• Manually adjustable.
E18JKK-1, E22JKK-1
• Do not adjust by hand.
6
VERTICAL AIRFLOW DIRECTION LOUVER
• Do not adjust by hand.
4
1 7
9
3
7
AUTO OFF/ON BUTTON
• Use when remote control is misplaced or a malfunction occurs.
Press once. Auto Press and hold until 1 beep is heard,
then release. Press and hold until 1 beep is heard,
then release. Press again until 2 beeps are heard, then release.
Press the button to turn off.
8
• It is recommended to clean the fi lter every 6 months.
• Replace the fi lter every 3 years or replace any damaged
lter. Part no.: CZ-SA20P
9
• Air fi lter cleaning is required every two weeks.
• Wash/rinse the fi lters gently with water to avoid damage
to the fi lter surface.
• Dry the fi lters thoroughly under the shade, away from
re or direct sunlight.
• Replace any damaged fi lters.
Action Mode
Cooling
Heating
AIR PURIFYING FILTER
Vacuum the air purifying fi lter.
AIR FILTERS
5

REMOTE CONTROL

AUTO HEAT
COOL
DRY
FAN
SPEED
AIR
SWING
FAN SPEED
AIR SWING
MODE
QUIET
TEMP
OFF/ON
POWERFUL
TIMER
SET
CANCEL
ON
OFF
1
2
3
SET CHECK CLOCK RESET
AC
RC
Maximum distances: 26ft
INDICATOR
POWER
TIMER
QUIET
POWERFUL
(Green) (Orange) (Orange) (Orange)
Press the remote control’s button
1
TO TURN ON OR OFF THE UNIT
• Please be aware of the OFF indication on the remote control display to prevent the unit from starting/stopping improperly.
2
TO SET TEMPERATURE
• Selection range : 60°F ~ 86°F.
• Operating the unit within the recommended temperature could induce energy saving. HEAT mode : 68°F ~ 75°F. COOL mode : 78°F ~ 82°F. DRY mode : 2°F ~ 4°F lower than room temperature.
4
TO SELECT FAN SPEED (5 OPTIONS)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
TO ADJUST VERTICAL AIRFLOW DIRECTION
5
(5 OPTIONS)
AIR SWING
• Keeps the room ventilated.
• In COOL/DRY mode, if AUTO is set, the louver swing up/down automatically.
• In HEAT mode, if AUTO is set, the louver fi x at predetermined position.
6
TO ADJUST AIRFLOW DIRECTION (5 OPTIONS)
(PAGE 7)
AIR SWING
• Keeps the room ventilated.
• In COOL/DRY mode, if AUTO is set, the louver swing left/right and up/down automatically.
• In HEAT mode, if AUTO is set, the horizontal louver fi x at predetermined position. The vertical louver swing left/right after the temperature rises.
Remote Control display
3
TO SELECT OPERATION MODE
AUTO mode - For your convenience
• During operation mode selection the power indicator blinks.
• Unit selects operation mode every 30 minutes according to temperature setting, outdoor and room temperature (For Single Split System).
• Unit selects operation mode every 3 hours according to temperature setting, outdoor and room temperature (For Multi Split System).
HEAT mode - To enjoy warm air
• Unit takes a while to warm up. The power indicator blinks during this operation.
COOL mode - To enjoy cool air
• Use curtains to screen off sunlight and outdoor heat to reduce power consumption during cool mode.
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
6
10 13
1
3
4
2
5
7
8
9
12
11
E9JKKW-1, E12JKKW-1
7
NOTES
QUIET
POWERFUL
Q
TO SET THE TIMER
S
O
FAN SPEED
MODE
QUIET
TEMP
OFF/ON
AIR SWING
POWERFUL
TIMER
SET
CANCEL
ON
OFF
1
2
3
SET CHECK CLOCK RESE
AC
RC
TO ENJOY QUIET OPERATION
• This operation reduces airfl ow noise.
TO REACH TEMPERATURE
8
QUICKLY
• Single Split System: This operation stops automatically after 20 minutes.
• Multi Split System: Press the button again or turn OFF the unit to stop this operation.
Press and hold for 5 seconds to dim or restore the
9
unit’s indicator brightness.
Press and hold for approximately 10 seconds to
10
show temperature setting in °C or °F
Press and hold for approximately 5 seconds to show
11
12-hour (am/pm) or 24-hour time indication.
12
Press to restore the remote control’s default setting.
13
Not used in normal operations.
NOTES
,
• Can be activated in all modes and can be cancelled by pressing the respective button again.
UIET
POWERFUL
,
• Cannot be selected at the same time.
TO SET THE TIMER
• To turn ON or OFF the unit at a preset time.
ON
1
OFF
Select ON or
OFF timer
• To cancel ON or OFF timer, press press
CANCEL
.
2
ET
Set the time Confi rm
N
OFF
or
then
• When ON Timer is set, the unit may start earlier (up
to 35 minutes) before the actual set time in order to achieve the desired temperature on time.
• Timer operation is based on the clock set in the
remote control and repeats daily once set. For clock setting, please refer to Remote Control Preparation at back cover.
• If timer is cancelled manually or due to power failure,
you can restore the previous setting (once power is resumed) by pressing
SET
.
E18JKK-1, E22JKK-1
6
7

TROUBLESHOOTING

The following symptoms do not indicate malfunction.
SYMPTOM
CAUSE
Check the following before calling for servicing.
SYMPTOM
CHECK
The following symptoms do not indicate malfunction.
SYMPTOM
Mist emerges from indoor unit. • Condensation effect due to cooling process. Water fl owing sound during operation. • Refrigerant fl ow inside the unit. The room has a peculiar odour. • This may be due to damp smell emitted by the wall,
carpet, furniture or clothing.
Indoor fan stops occasionally during automatic fan speed
• This helps to remove the surrounding odours.
setting. Airfl ow continues even after operation has stopped. • Extraction of remaining heat from the indoor unit
(maximum 30 seconds). Operation is delayed a few minutes after restart. • The delay is a protection to the unit’s compressor. Outdoor unit emits water/steam. • Condensation or evaporation occurs on pipes. Timer indicator is always on. • The timer setting repeats daily once set. Power indicator blinks during HEAT mode with no warm air
supply (and louver is closed).
• The unit is in defrost mode (and AIR SWING is set to
AUTO). Indoor fan stops occasionally during heating operation. • To avoid unintended cooling effect. Power indicator blinks before the unit is switched on. • This is a preliminary step in preparation for the operation
when the ON timer has been set. Cracking sound during operation. • Changes of temperature cause the expansion/contraction
of the unit.
Check the following before calling for servicing.
SYMPTOM
Heating/Cooling operation is not working effi ciently. ► • Set the temperature correctly.
• Close all doors and windows.
• Clean or replace the fi lters.
• Clear any obstruction at the air inlet and air outlet vents.
Noisy during operation. • Check if the unit has been installed at an incline.
• Close the front panel properly.
Remote control does not work. (Display is dim or transmission signal is weak.)
• Insert the batteries correctly.
• Replace weak batteries.
The unit does not work. • Check if the circuit breaker is tripped.
• Check if timers have been set.
The unit does not receive the signal from the remote control.
• Make sure the receiver not obstructed.
• Certain fl uorescent lights may interfere with signal transmitter. Please consult authorized dealer.
CAUSE
CHECK
The unit stops and the timer indicator blinks.
Use remote control to retrieve error code.
Press for 5
1
seconds.
Press for 5
3
seconds to quit checking.
Turn the unit off and reveal the error code to authorized dealer.
4
TIMER
ON
1
2
OFF
SET CHECK CLOCK RESET
CANCEL
AC
SET
3
RC
8
Press until you hear
2
beep sound, then write down the error code.
Note:
• For certain errors, you may restart the unit for limited operation with 4 beeps during operation starts.

INFORMATION

Information for Users on Collection and Disposal of Old Equipment and used Batteries
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
Contact your country hazardous waste disposal hotline.
FOR SEASONAL INSPECTION AFTER EXTENDED NON-USE
• Checking of remote control batteries.
• No obstruction at air inlet and air outlet vents.
• After 15 minutes of operation, it is normal to have the following temperature difference between air inlet and air outlet vents: Cooling: 46.4°F Heating: 57.2°F
FOR EXTENDED NON-USE
• Activate Heat mode for 2~3 hours to remove moisture left in the internal parts thoroughly to prevent mould growth.
• Turn off the power supply.
• Remove the remote control batteries.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.
Pb
SERVICEABLE CRITERIAS
TURN OFF POWER SUPPLY then please consult authorized dealer under the following conditions:
• Abnormal noise during operation.
• Water/foreign particles have entered the remote control.
• Water leaks from Indoor unit.
• Circuit breaker switches off frequently.
• Power cord becomes unnaturally warm.
• Switches or buttons are not functioning properly.
9
MEMO
MEMO

QUICK GUIDE

MODE
OFF/ON
TEMP
Remote Control Preparation
Remote Control Preparation
1
2
3
5 6
4
TIMER
ON
1
OFF
SET CHECK CLOCK RESET
1
AUTO HEAT DRY COOL
Select the desired mode.
2
Start/stop the operation.
3
Select the desired temperature.
2
AC
SET
3
CANCEL
RC
MODE
OFF/ON
TEMP
Pull out
1
Insert AAA or R03 batteries (can be used ~ 1 year)
2
Close the cover
3
Press CLOCK
4
Set time
5
Confi rm
6
AUTO
HEAT
COOL
DRY
OFF/ON
MODE
QUIET
TIMER
ON
1
OFF
SET CHECK CLOCK RESET
TEMP
POWERFUL
2
FAN SPEED
AIR SWING
CANCEL
AC
FAN SPEED
AIR SWING
SET
3
RC
2 1
3
AUTO
HEAT
COOL
DRY
OFF/ON
MODE
TEMP
POWERFUL
QUIET
TIMER
ON
1
2
OFF
SET CHECK CLOCK RESET
FAN SPEED
AIR SWING
FAN SPEED
AIR SWING
SET
3
CANCEL
AC
RC
E9JKKW-1, E12JKKW-1 E18JKK-1, E22JKK-1
Panasonic Corporation
Website: http://panasonic.net/
For enquiries, please call 1-800-851-1235
Printed in Malaysia
OSSC1004-00 F567672
Loading...