Panasonic CF-30CTQAZBM Reference Manual

Reference Manual

Personal Computer

Model No. CF-30 Series

We recommend that this Reference Manual be printed.

Key Combinations

NOTE

z Do not repeatedly press the keys in quick succession. z Do not use the key combinations together with touch pad (external mouse), touchscreen (only for model with touch-

screen) or other key operations.

z Do not use the key combinations before you log on to Windows. Wait until the hard disk drive indicator turns off.

On the Setup Utility screen, you can use the key combinations of

z The key combinations may not work with some applications. z The popup menu icon appears after logging on to Windows. It may not appear in some application conditions (e.g.,

when [Command Prompt] is set to “Full Screen”).

Key Function Popup menu icon

Fn+F1, Fn+F2

and Fn+F3.

Fn+F1

Fn+F2

Fn+F3

LCD brightness

(

Fn+F1

Display switching (Î page 37)

(When an external display is connected) Internal LCD Simultaneous display External display

= down / Fn+F2= up)

NOTE

z To obtain higher brightness, set [LCD Brightness Mode] to [High Brightness]

in the [Main] menu of the Setup Utility. (Î page 56)

CAUTION

z Do not press any keys until the display has finished switching. z Do not use this function:

• When an external display is not connected.

• When playing motion video such as DVD or MPEG.

• When using the Extended Desktop.

• When showing a game screen such as pinball.

Key Combinations

Key Function Popup menu icon

Fn+F4

Fn+F5

Fn+F6

Fn+F7

Fn+F9

Fn+F10

Speaker on/off

NOTE

z Beeps do not sound if you turn off the speaker sound. z You cannot turn off the sound of speakers connected to the USB port.

Volume

(

Fn+F5

Activate standby (Î page 8)

Remaining battery level (Î page 13)

Activate hibernation (Î page 8)

= down / Fn+F6= up)

NOTE

z This does not work on beeps or speakers connected to the USB port.

OFF

(MUTE)

Key Combinations

Hotkey Settings

You can make two settings:

• Fn key lock

is locked (pressed-down) until you press another key. Use this when pressing difficult key combinations.

• Popup menu icon on/off

1 Start up the Hotkey Settings.

Click [start] - [All Programs] - [Panasonic] - [Hotkey Settings].

2 Make the settings.

[Use Fn key lock]

z When using an

A Press B Press another key. (Lock released)

z When using successive

A Press B Press another key.

Fn key remains locked until you press

key combination

once. (Locked)

twice. (Locked)

key combinations

again.

[Notification]

[Make sounds when Fn key is pressed] [Show status on screen]: Displays the Fn key status on the notification area.

•:

[Disable popup]

The popup menu icon will not be displayed.

is locked.

is not locked.

3 Click [OK].

NOTE

z You can have different settings for each user.

If the speakers are muted, beeps do not sound.

Touchscreen

You can use the touchscreen function to perform the same operation as the touch pad and mouse. Touch the screen surface with the stylus (included).

z To right-click

A Click on the notification area.

changes to .

B Click the object you want to right-click.

returns to .

NOTE

z You need to make the following setting for each user.

A Click [start] - [All Programs] - [Fujitsu Touch Panel (USB)] - [Touch Panel Configuration]. B Select the settings, and then click [OK].

z Do not add a check mark to [Delete Cursor] since the display may be distorted.

z If you add a check mark for [Use] in [Hold [Ctrl] key down + Touch the screen] of [Touch Panel Configuration], touching

the screen may always be recognized as a right-click. To return to the normal operation, press

z The touchscreen function does not work in the Setup Utility, in the full screen of [Command Prompt] or in or Recover

Pro (Î page 67).

Ctrl

on the keyboard.

Touchscreen Calibration

1 Run [Touch Screen Calibration Utility].

Click [start] - [All programs] - [Fujitsu Touch Panel (USB)] - [Touch Screen Calibration Utility].

2 Using the stylus, touch each of the 12 “+” target marks one by one until it blinks, and then

click [Calibration].

3 Click [Save & Exit].

NOTE

z Perform the touchscreen calibration for each user.

Panasonic Hand Writing

You can make a bitmap file (.bmp) of a simple character and a figure such as signature by handwriting on the touch pad and the touchscreen (only for model with touchscreen).

CAUTION

z Do not use the Fast User Switching function while Panasonic Hand Writing is active. z If you install other pointing devices (e.g., commercially available mouse driver) and overwrite the touch pad driver,

Panasonic Hand Writing will not work.

NOTE

z The display of Panasonic Hand Writing may be distorted if the number of display colors is changed. Right-click on

the notification area and click [Exit Panasonic Hand Writing], and then restart Panasonic Hand Writing.

z Panasonic Hand Writing may not work properly if another application software is active. In this case, close the applica-

tion software and try handwriting again.

Starting Panasonic Hand Writing

1 Double-click on the notification area.

Alternatively you can click [start] - [All Programs] - [Panasonic] - [Panasonic Hand Writing].

NOTE

z Select the image size before handwriting by clicking [Option] - [Window size]. If you change the size after handwriting,

the image quality will become lower.

z You can copy the bitmap image by clicking [Edit] - [Copy], and paste it in another application software that supports bit-

map format.

z The touch pad mode will not work properly when using the extended desktop. z The touch pad mode will be canceled in the following cases.

• Switching to another application

• Resuming from standby or hibernation

• Pressing

• Touching the touchscreen (only for model with touchscreen)

z An external mouse or trackball connected via the port replicator (optional) will not work during handwriting in the touch

pad mode.

Alt

Standby and Hibernation Functions

The standby or hibernation function allows you to shut off the computer without closing programs and documents. You can quickly return to the programs and documents that you were working on before standby or hibernation.

Function Data is saved to Recovery time Power supply

Standby Memory Short Required. (If power is not supplied, all data will be lost.)

Hibernation Hard disk Rather long Not required. (However power is slightly consumed to

keep the hibernation.)

Setting Standby or Hibernation

1 Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Options] -

[Advanced].

2 Select [Stand by] or [Hibernate] for [When I close the lid of my portable computer:] /

[When I press the power button on my computer:], and then click [OK].

NOTE

z You do not need to make the setting if you use the Windows menu to enter standby or hibernation.

Precautions

z Connect the AC adaptor if the computer will be in standby mode for a long period of time. If you cannot use the AC adap-

tor, use hibernation instead.

z Using standby or hibernation repeatedly may cause malfunction of the computer. To stabilize computer operation, restart

Windows regularly (about once a week) without using standby or hibernation.

z Save the necessary data. z Close files you have opened from removable disk and network drive. z The password you set in the Setup Utility is not requested at resuming. You can use the Windows password for security in

standby or hibernation.

A Click [start] - [Control Panel] - [User Accounts], and select the account. B Click [Create a password] and set the password. C Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Options] - [Advanced], and add the

check mark in [Prompt for password when computer resumes from standby].

Standby and Hibernation Functions

z Do not enter standby or hibernation in the following conditions, otherwise the data or file may be corrupted, standby or

hibernation may not work, or malfunction may occur in the computer or the peripheral devices.

• When any of the multimedia pocket device indicator

cator is on.

• When playing/recording audio files or displaying motion video such as MPEG files.

• When playing a DVD-Video.

• When writing to a disk.

• When using communication software or network function.

• When using a PC Card. (If the card fails to work normally, restart the computer.)

• When an external mouse is connected to the serial port.

z The computer does not enter standby or hibernation immediately after resuming. Wait approximately one minute.

Except when using a second battery pack

, the hard disk drive indicator and the SD Memory Card indi-

Entering/Resuming from Standby or Hibernation

 To enter standby or hibernation

1 Close the display, or slide the power switch (A) until a beep

sounds.

Standby: The power indicator (B) blinks green. Hibernation: The power indicator (B) goes off. z You can alternatively use the Windows menu to enter standby or hibernation. To

enter standby, click [start] - [Turn Off Computer] - [Stand By]. To enter hibernation, click [start] - [Turn Off Computer], then press and hold [Hibernate].

CAUTION

While the computer is entering standby or hibernation

z Do not:

• Touch the keyboard, touch pad, touchscreen (only for model with touchscreen), or power switch.

• Use an external mouse or other peripheral device.

• Connect or disconnect the AC adaptor.

• Close or open the display. Wait until the power indicator blinks green (standby) or goes off (hibernation).

z It may take one or two minutes to enter standby or hibernation.

Shift

and click

Standby and Hibernation Functions

z At the beep*2, immediately release the power switch. If you slide and hold the power switch for longer than four sec-

onds, the computer will forcibly shut down and unsaved data will be lost even if you have set [Shut down] in [When I press the power button on my computer:] (Î page 7 “Setting Standby or Hibernation”).

In standby or hibernation

z Do not attach or remove a multimedia pocket device (excluding a second battery pack) and peripheral device. Doing

so may cause malfunction.

z Power is consumed in standby mode. Power consumption may increase when a PC Card is inserted. When power is

exhausted, the data retained in memory will be lost. Connect the AC adaptor when using the standby function.

If the speakers are muted, beeps do not sound.

 To resume from standby or hibernation

1 Open the display, or slide the power switch (A).

z When [Stand by] or [Hibernate] is selected as the setting for [When I close the lid of my

portable computer] (Î page 7), you can resume operation opening the display.

CAUTION

z Do not perform the following operations until resuming is complete. After the display has resumed, wait approximately

30 seconds (normally) or 60 seconds (when the computer is on a network).

• Touch the keyboard (except for password input), touch pad, touchscreen (only for model with touchscreen), or power

switch.

• Use an external mouse or other peripheral device.

• Connect or disconnect the AC adaptor.

• Close or open the display.

• Shut down or restart Windows.

• Enter standby or hibernation.

Security Measures

Use these features to protect your data. z Other security measures

• SD Security (

• Embedded Security (TPM) ( Module (TPM)”.

Setting the Supervisor Password/User Password

Set the Supervisor Password before setting the User Password.

1 Start up the Setup Utility (Î page 54). 2 Select [Security].

Î page 26)

Î page 60): For further information, refer to the Installation Manual of “Trusted Platform

3 Select [Set Supervisor Password] or [Set User Password], and press

4 Enter your password in [Enter New Password] and press

z When the password has been set, you need to enter your password in [Enter Current Password] and press

Enter

z To disable the password, leave the input field empty and press

Enter

5 Enter your password again in [Confirm New Password] and press 6 In [Setup Notice], press

7 Press

CAUTION

z Do not forget your password. If you forget your Supervisor Password, you will not be able to use your computer. Con-

tact Panasonic Technical Support.

z When running the Setup Utility, do not leave and go away from your computer even for a short time, since other people

may set or change the password.

NOTE

z The password will not be displayed on the screen. z You can use up to 32 alphanumeric characters (including spaces).

• The case (upper/lower) is ignored.

• To input numbers for the password, you cannot use the numbered keys on the keyboard.

• You cannot use

z Disabling the Supervisor Password also disables the User Password.

F10

, and then select [Yes] and press

Shift

and

Enter

Ctrl

to input a password.

Enter

Security Measures

Preventing Your Computer from Unauthorized Use

You can set a start-up password to protect your computer from unauthorized use.

1 Set the password (Î page 10), and select [Enable] in [Password on boot] in the [Security]

menu of the Setup Utility (Î page 60).

NOTE

z If the Supervisor Password or User Password has been set, the password input screen will be displayed on starting-up

of the Setup Utility even though [Password on boot] is set to [Disable].

Preventing Your Hard Disk Data from Being Read or Written

The hard disk lock function protects the hard disk data from being read or written when the hard disk is attached to another computer. The data can be read/written when the hard disk is returned to the original computer. (Note that the hard disk lock does not guarantee complete protection of the data.)

1 Select [Enable] in [Hard Disk Lock] in the [Security] menu of the Setup Utility (Î page 60).

CAUTION

z For the data being read/written on the original computer, the Setup Utility settings must be the same as when the hard

disk was removed.

z You cannot use the hard disk lock function without setting the Supervisor Password. Set the Supervisor Password

beforehand (Î page 10).

z When you have your hard disk drive repaired

• Contact Panasonic Technical Support.

• Before sending back the hard disk drive, be sure to set the [Hard Disk Lock] to [Disable].

NOTE

z The hard disk lock function works with the built-in hard disk. It does not work with the external hard disk. z We recommend you to set [Password on boot] to [Enable] to ensure security though it is not required to enable the

hard disk lock.

Battery Power

Battery Indicator

Battery indicators: Main battery pack, Second battery pack

Battery indicator Battery status

Not lit The battery pack is not inserted or not being charged.

Orange Charging is in progress.

Green The battery is fully-charged.

Blinking green

Red The remaining battery is approximately 9% or less.

Blinking red The battery pack or the charging circuit is not operating properly.

Blinking orange The battery cannot be charged temporarily due to the following reasons:

Blinking green and orange alternately

Only for the main battery pack.

In high temperature mode, the 100% battery level is equivalent to 80% level of the normal temperature mode.

NOTE

z Once the battery is fully charged, the computer performs recharging only when the battery level becomes less than

approximately 95%, so overcharging is avoided.

In high temperature mode, the battery pack is discharging the power to 80%*2 of normal temperature mode (Î page 14). Do not remove the battery pack in this status.

• Its internal temperature is out of the acceptable range.

• The power supply is not enough because software applications or peripheral devices are consuming a large amount of power.

The temperature is low and the computer is warming up to prevent the hard disk drive from malfunctioning. The computer will start automatically after warming-up.

Battery Power

Checking the Remaining Battery Charge

You can check the remaining battery charge on the screen.

(After logging on to Windows)

1 Press

z When the battery pack is inserted (example)

z When the battery pack is not inserted

Left icon: Main battery Right icon: Second battery (optional)

NOTE

z The battery display may not correspond to the actual remaining battery charge in the cases as below. To correct the

display, perform the Battery Recalibration (Î page 16).

• The battery indicator remains red.

• The indicator lights orange and the display shows 99% for a long time.

• Low battery warning appears soon after a short time of use. This can occur when the computer is in standby mode for a long time without power supply from the AC adaptor.

z The battery display may not be the same as that of notification area or of [Power Meter] in [Power Options Properties].

This is not a malfunction.

Fn+F9

: Normal temperature mode (Î page 14)

: High temperature mode (Î page 14)

Battery Power

High temperature mode

The high temperature mode can prevent the battery from deteriorating when the computer is used in high-temperature environment or used for a long time with its battery fully charged. Select [Auto] (default) or [High Temperature] in [Environment] of the [Main] menu of the Setup Utility (Î page 56).

NOTE

z Note that a level corresponding to a 100% charge for high temperature mode is approximately equivalent to an 80%

charge level for normal temperature mode.

z After switching from [Normal Temperature] to [High Temperature] or vice versa, the remaining battery capacity will not

be displayed correctly until the battery pack is completely discharged or fully charged.

z In the [Auto] mode:

Once the computer has automatically switched from the normal temperature mode to the high temperature mode, the computer will not switch back to the normal temperature mode until the battery has been used and recharged to a total charge level of about five times as much as that of the fully-charged state. This is to avoid battery deterioration.

Battery Power

Computer behavior with low battery

The default settings are as follows.

When the battery level becomes 10% [Low battery alarm]

z Displays a message that the battery level is low. z Displays a message that the battery level is low, and

↓↓

Charge the battery. Connect the AC adaptor or replace the battery to start up

z Connect the AC adaptor immediately. If you do not

have the AC adaptor, exit the running programs and Windows, then confirm that the power indicator is off.

z If you have a fully charged spare battery, turn off the

computer, replace the battery and turn the computer on again.

Do not replace the battery pack when the computer is in standby mode.

When the battery level becomes 5% [Critical battery alarm]

then the computer enters hibernation.

the computer.

z Connect the AC adaptor and charge the battery. z If you have a fully charged spare battery, replace the

battery and turn the computer on again. When the computer enters hibernation with the battery down and you resume the operation without charging the battery, Windows may not start up normally or the alarm function may not operate normally from then on.

Battery Power

Correcting the Battery Display (Battery Recalibration)

The “Battery Recalibration” function measures and memorizes the battery capacity. To correct the battery display, use this function to fill the battery and then discharge it completely. Perform the procedure at least once immediately after purchasing the computer. Normally the interval of battery recalibration is three months. The battery display may not be correct when the battery pack deteriorates after a long time use. In this case, perform the procedure again.

1 Connect the AC adaptor. 2 Close all the applications.

3 Perform “Battery Recalibration”.

A Click [start] - [All Programs] - [Panasonic] - [Battery Recalibration]. B When the confirmation message appears, click [Start].

z Frequent recalibration of the battery can degrade the battery. A caution message appears when the battery

recalibration is performed at the shorter interval than approximately a month. In this case, cancel the battery recalibration.

C When the message requests shut down of Windows, click [Yes].

The battery recalibration starts. After the battery pack is fully charged, discharging starts. When the discharging is completed, the power goes off automatically.

After the battery recalibration is finished, normal charging starts.

NOTE

z The temperature range should be 10 z The battery recalibration may take a long time due to the large battery capacity. This is not a malfunction.

• Full charge: Approximately 5 hours [max.]

• Complete discharge: Approximately 5 hours (only for model with touchscreen)

Approximately 6 hours (only for model without touchscreen)

z If the computer is turned off during the battery recalibration (e.g., due to power failure, or accidental removal of the AC

adaptor and battery pack), the battery recalibration will not be completed.

z You can also perform the battery recalibration with the following procedure.

A Restart the computer. B Press C When the remaining battery capacity is displayed, press D Follow the on-screen instructions.

while the [Panasonic] boot screen is displayed just after the computer starts the startup procedure.

°C to 30°C {50°F to 86°F}.

Enter

Battery Power

Replacing the Battery Pack

The battery pack (CF-VZSU46U) is a consumable item so the replacement will be necessary. If the battery operation time becomes noticeably short and not recovered even after recalibrating the battery, replace with a new battery. If necessary, attach the second battery pack to the multimedia pocket (Î page 19).

CAUTION

z The battery pack is not charged when you first purchase it. Be sure to charge it before using for the first time. Charging

starts automatically when the AC adaptor is connected to the computer.

z Use only the specified battery pack with your computer. z In the standby mode, do not remove/replace the battery pack. Otherwise your data will be lost and the computer may

be damaged.

1 Turn off the computer.

z Do not use the standby function.

2 Remove/Insert the battery pack.

z To r em ov e

A Slide the latch (A) to the right to unlock the cover.

B Slide the latch (B) down, and open the cover.

Battery Power

C Pull the tab (C) of the battery pack.

z To i ns er t

A Insert the battery pack until it securely fits the connector. B Close the cover until it clicks.

C Slide the latch (D) to the left to lock the cover.

CAUTION

z Make sure the latch is securely locked, otherwise the battery pack may fall when you carry the computer.

Multimedia Pocket

You can attach the following devices. (refer to recent catalogs and other sources for information about the products available)

z DVD-ROM & CD-R/RW drive (optional) z DVD MULTI drive (optional) z Second battery pack (optional: CF-VZSU1430U)

CAUTION

z Do not insert/remove the multimedia pocket device in standby or hibernation, or when the multimedia pocket device

indicator or the hard disk drive indicator is on.

NOTE

z Refer to the catalogs etc. for the latest information about optional devices. z Read the instruction manuals of the devices carefully.

Replacing the Multimedia Pocket Device

1 Disable the multimedia pocket device function.

A Double-click on the notification area. B Select the multimedia pocket device and then click [Stop]. C Follow the on-screen instructions.

D Confirm that the multimedia pocket device indicator and the hard disk drive indicator indicators are not lit.

z This step is not necessary when;

• Removing the device after turning off the computer.

• is not displayed.

• The device does not appear in the list in step B.

• Removing the second battery pack.

2 Slide the latch (A) and open the cover.

Multimedia Pocket

3 Press the release handle (B).

The release handle pops out.

4 Pull the release handle (B) to draw out the device partway, and hold

the device on its both sides to remove.

5 Carefully insert the device into the multimedia pocket by pushing

both corners until it surely fits in the slot.

z Press the release handle (C) to set in. z The computer must be on when inserting the device. z Insert the device with the label side up.

6 Close the cover until it clicks.

CAUTION

z Hold the device by both sides. Otherwise the device may be damaged. z Do not apply excessive force when raising the slot side upward and inserting the device.

NOTE

z You can see that the device is recognized or not by double-clicking

mation] menu in the Setup Utility (Î page 55). (When using a second battery pack, press recognized (or if the media cannot be accessed), turn off the computer and reinsert the device.

on the notification area, or checking the [Infor-

Fn+F9

.) If the device is not

PC Card / ExpressCard

You can insert the following cards.

z ExpressCard/34 or ExpressCard/54 to the ExpressCard slot (A) z PC Card Type I (3.3 mm) or II (5.0 mm) to the PC Card slot (B)

NOTE

z The following types of card are not supported:

PC Card Type III (10.5 mm), ZV card, SRAM card, FLASH ROM card (excluding ATA interface type), and other cards that require 12 V of operating voltage.

Inserting/Removing the Card

Preparation

Attach the device for the media containing the card driver (e.g., CD-ROM). Equipment connected to the multimedia pocket cannot be recognized if connected after the card driver installation screen appears.

 To insert the card

1 Slide the latch (C) and open the cover.

2 Insert the ExpressCard (left solt) (D) or the PC Card (right slot)

(E) with the label side up until it securely fits in to the slot.

z For further information, refer to the instruction manual of the card.

PC Card / ExpressCard

 To remove the card

1 Disable the card function.

A Double-click on the notification area and select the card, then click [Stop]. B Follow the on-screen instructions.

z This step is not necessary when removing the card after turning off the computer.

2 Open the cover and remove the card.

z ExpressCard (F)

A Press the card so it comes out of the slot. B Draw the card straight out.

z PC Card (G)

A Press the eject button so the card comes out of the slot. B Draw the card straight out.

NOTE

z Check the card’s specification to prevent the total operating current from exceeding the allowable limit. Otherwise mal-

function may occur. Permissible Current: 3.3 V: 400 mA, 5 V: 400 mA

z Some types of cards cannot be used simultaneously. z After repeating insertion and removal, some types of card will not be recognized. In this case, restart the computer. z If the computer freezes after resuming from standby or hibernation, remove and reinsert the card. If the problem per-

sists, restart the computer.

z When a card is inserted, power consumption increases. Remove the card when it is not in use, especially when oper-

ating by battery power.

z To connect peripheral devices (SCSI, IEEE 1394, etc.) using a PC Card or an ExpressCard, follow the steps below

(one example).

A Connect the peripheral device to the card. B Turn on the power of device. C Insert the card until it surely fits in the slot.

SD Memory Card

SD Memory Card Information

z The SD Memory Card has a copyright protection function which is compatible with content on-demand services on the

Internet, etc.

z To format the SD Memory Card on this computer, do not use [Format] of Windows, but use the SD Memory Card format

software. You can download the software from the web site below. http://panasonic.co.jp/pavc/global/cs/sd/download/sd_formatter.html

z To use the SD Memory Card on other devices, format the card on those devices. For further information, refer to the

instruction manual of the devices.

z This computer is not compatible with SDHC Memory Cards (SD Memory Cards with a capacity of 4 GB or more).

To use this kind of card, you will need to obtain a compatible PC Card adaptor or USB reader/writer.

Handling and storage cautions

z Store the SD Memory Card in the case after removing it from the computer. z Do not:

• Disassemble or modify the card.

• Hit, bend, or drop the card.

• Touch the terminals with fingers or metal object.

• Remove the labels of the card / Attach other labels or stickers to the card.

z Do not place the card in the following locations.

• In direct sunlight or in very hot location such as inside of a car.

• In very dusty or humid location.

• In location subject to corrosive gas, etc.

Data handling cautions

z Set the write-protect switch (A) to the LOCK position. Unlock the switch when recording

(checkout), saving, or editing data.

z We recommend you to back up the important data to another storage medium. z When disposing the card, we recommend you to physically destroy the card (using a ham-

mer, etc.) to prevent personal or confidential data leakage.

SD Memory Card

Inserting/Removing the SD Memory Card

CAUTION

z Do not remove or insert the SD Memory Card until Windows has completed loading. z Do not remove the card or turn off the computer in the following cases, otherwise the data may be corrupted.

• While the computer is in standby or hibernation.

• Immediately after the writing operation. The computer may still continue the access to the card just after writing operation. If you remove the card before the operation is completed, the data may be damaged or the card access may no longer be performed normally.

z Note that Panasonic assumes absolutely no liability for any loss of data recorded by the user, or any other damages,

direct or indirect.

z Do not forcibly draw out the card, otherwise the slot may be damaged. z Insert the card in the correct direction, otherwise the card and the slot may be damaged. z After resuming from standby or hibernation, do not access the SD Memory Card for approximately 30 seconds.

 To insert the card

1 Slide the latch (A) and open the cover, and insert the SD Memory

Card with the label side facing up and with the cut corner facing in.

 To remove the card

Preparation

z Save the data and close all applications. z Open the cover and confirm the SD Memory Card indicator (B) is off.

1 Disable the card function.

A Double-click on the notification area and click [Secure Digital Storage Device],

then click [Stop].

B Follow the on-screen instructions.

z This step is not necessary when removing the card after turning off the computer.

+ 54 hidden pages