Panasonic CF-27EB6GDAM Operating Instruction Windows NT
Personal Computer
Supplementary Instructions for Windows® NT® 4.0
CF-27 Series
This manual contains supplementary instructions regarding the use of the computer . It explains the cases
where the operation of the computer differs from that in the Operating Instructions and Reference Manual.
Contents
®
NT
First-time Operation ..........................................2
Starting Up/Shutting Down............................... 4
Dealing With Pr oblems......................................6
Reinstalling Software..................................... 11
Specifications................................................. 14
The following functions are not supported with Windows NT. Please ignore the description
in the "Operating Instructions" about the following functions.
Using USB Devices
Infrared Data Communications
®
Microsoft
NOTE
An application software is needed to use the infrared data communications. The infrared
data communications can not be used at 4 Mbps data transfer speed.
IntelliMouse™ Wheel Mode
Illustrations in this Manual
NOTE: NOTE provides a useful fact or helpful information.
CAUTION: CAUTION indicates a condition that may result in minor or moderate injury.
W ARNING: WARNING indicates a hazard that may result in moderate or serious injury .
[Start]-[Shut Down]: This illustration means to click [Start], then to click [Shut Down].
(For some applications, you may need to double-click.)
Enter : This illustration means to press the [Enter] key.
Fn + F5 : This illustration means to press and hold the [Fn] key , then press the [F5] key.
First-time Operation
Please read the steps below to help you learn what accessories are included, and to gain an understanding of some
basic computer-related operations.
Confirm the inclusion of all accessories (except belo w Operating Instructions page 8 )
1
Windows 95 System Pack .... 1
Windows® 95 Book
Product Recovery CD-ROM
Windows NT Workstation System
Pac k ....................................... 1
Windows NT® Book
Connect the battery pack ( Operating Instructions page 7)
2
Connect your computer to a power outlet ( Operating Instructions page 7)
3
Read the LIMITED USE LICENSE AGREEMENT ( Oper ating Instructions page 27)
4
Turn your computer on ( Operating Instructions page 8)
5
Setup Windo ws NT
6
The Software License Agreement will be displayed. After reading the agreement, select [I
1
Agree] or [I Disagree].
Registration Card
CD-ROM
®
Floppy Disk
Windows NT Service
P a c k 4.............1
FIRST AID CD...1
2
NOTE
Moving the cursor (
2
Select [Next].
Input your name and organization, then select [Next].
3
(It is possible to omit the organization item.)
Input the Product Number written on the “Certificate of Authenticity” located in the Win-
4
dows NT Book that comes with this computer then select [Next].
To move the cursor to a particular item, press Tab or click the desired box.
Input your computer name and select [Next].
5
Input an Administrator password and select [Next].
6
CAUTION
Remember this password! If the password is forgotten, Windows NT cannot be operated.
Select [Next].
7
When not establishing settings for a network:
Select [Do not connect this computer to a network at this time], then select [Next].
(Settings can be made for a network even after Windows starts up. In this case, be sure to
read [When Adding New Software or Hardware Components] in the Reference Manual [T echnical Information].)
When establishing settings for a network:
The settings will vary for different network environments depending on the network system
being used. For more details, ask your system administrator or the person in charge of the
network. Follow the on-screen instructions.
(It takes several minutes for the necessary files to be copied. If the computer enters the ECO
mode, the power to the LCD is automatically turned off. In this case, press a key unrelated to the
direct triggering of a selection, like .
) or clicking buttons can be performed with the touch pad.
Ctrl
Select [Restart Computer]. Select "Windows NT Workstation Version 4.00" and press .
8
9
Following the display , press Ctrl + Alt + Del . Input the password set in step and
select [OK], then select [Close] at the [Welcome] display.
As the computer starts up, it will be necessary to input the password set in step .
10
Follow the on-screen instructions and install DS-XG Driver for WinNT.
(At the [YAMAHA DS XG Audio Driver], select [OK]. When the installation completes, select [Yes, I want to restart my computer now], select [Finish].)
11
Follow the on-screen instructions and install Phoenix APM 2.0 for Windows NT.
When the installation completes, select [Don't Restart Now].
12
Follow the display and install Phoenix Card Executive™ for Windows NT.
When the installation completes, select [Restart Now].
13
The [Begin Logon] display will appear. Perform the operation in step .
14
Select [Next] at the [Card Executive 2.0 for NT Diagnostics].
Select [Next], then select [Finish].
15
Windows will restart.
16
The [Begin Logon] display will appear. Perform the operation in step .
Double-click the [Internet Explorer] icon to install Internet Explorer.
17
Follow the on-screen instructions.
At the [Installation Option], by clicking
At the [Confirm File Replace], press [No].
Windows will restart.
18
The [Begin Logon] display will appear. Perform the operation in step .
19
Set the correct settings for all items in [Control Panel]-[Regional Settings] and [Date/
Time] etc.
, select [Full Installation], then select [Next].
9
Enter
9
9
6
6
Create backup disks
7
Prepare 2HD floppy disks and make sure they are not in the write-protected state. Then, select
[Start] - [Programs] - [Panasonic] - [Create Tool disk]. Follow the on-screen instructions.
After this, place a label on each disk for identification purposes.
Names of created backup disks
Tool Disk, Backup Disk*
*
There are instances where it is not necessary to create backup disks.
CA UTION
Please store the floppy disks in a safe place. They will enable you to return your computer to factory default settings should any problems occur.
Do not remove the floppy disk while the FDD indicator ( ) is on, power down your
computer or use the suspend function ( "Suspend / Hibernation Functions").
When creating floppy disks, do not run any other application program.
When creating floppy disks and the message [Insufficient files to copy] is displayed,
press [OK] then contact Panasonic Technical Support.
The T ool Disk cannot be accessed through [My Computer] or by typing the "DIR" command at the Command Prompt, because it uses a special file format.
Install Acrobat® Reader 3.01 ( Operating Instructions page 9)
8
Partition the Hard Disk
9
The hard disk includes an NT file system (NTFS) partition of 4GB. The remaining free hard
disk space can be used when necessary by creating more partitions (in [Start]-[Programs][Administrative T ools (Common)]-[Disk Administrator]).
NOTE
In Windows NT4.0 Service Pack 4 CD-ROM, "Microsoft Data Access Components 2.0
Service Pack 1" etc. are included. Please read NTSP4.HTM and Y2K.TXT in Windows
NT4.0 Service Pack 4 CD-ROM, and install if necessary. To see the contents of Windows
NT4.0 Service Pack 4 CD-ROM, the CD-ROM drive is needed.
3
Starting Up/Shutting Down
Starting Up
Open the display ( Operating Instructions page11)
1
Turn your computer on ( Operating Instructions page 11)
2
Select your operating system
3
Select "Windows NT Workstation Version 4.00" and press Enter .
Logon
4
Wait for 10 seconds after confirming that the HDD access has been completed, then press Ctrl + Alt
+ Del .
Input your password
5
Input the user name and password, then press [OK]. If [Cancel] is clicked, the computer will return to
the initial [Begin Logon] display . Until the correct user name and password are entered, the computer
will not operate.
Select your application
6
You are able to start working on your computer.
NOTE
The power saving function is factory set to remove power from the LCD if the computer is not
operated or no access is made to a device for two minutes. The LCD will resume normal operation if
the touch pad is moved or if a key on the keyboard is depressed.
Using the Touch Pad
The touch pad driver is not installed.
(Use the touch pad to move the cursor (
Basic Operation
Function
Moving the Cursor
Tapping/Clicking
Double-Tapping/
Double-Clicking
below) on the display and perform normal computer operations.)
Touch Pad Operation
Move the tip of your finger
lightly over the surface.
or
tapping
or
clicking
4
Dragging
double-tapping
or
Two quick taps, but on
the second tap leaving
your finger down (applying pressure) and moving
it on the work surface.
double-clicking
While holding down the
button, moving your finger on the work surface.
Shutting Down (power off your computer)
This procedure is shutting down without using the suspend or hibernation function.
Display the shut down screen ( Operating Instructions page 18)
1
Confirm shut down
2
Select [Shut down].
Your computer will power off automatically.
(In the OFF state, if you are not recharging your battery pack or if the pack is fully charged, your computer consumes approximately 1.5 W.)
NOTE
For the computer to automatically shut down after [Shutdown] is selected, Phoenix APM 2.0 for
Windows NT
the program is installed.
Restarting your computer (without shutting down) ( Operating Instructions page 18)
®
has to be installed. When and are displayed on the taskbar, this indicates that
5
Loading...