Panasonic CQ-C9901W, C9801W User Manual
2
CQ-C9901W/C9801W
3
English
CQ-C9901W/C9801W
Safety Information
Safety Information
Warning
Observe the following warnings when using
this unit.
❑
The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and use
the parking brake before watching the display or operating
the system.
❑
Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery
system.
❑
Keep batteries and insulation film out of reach of
infants.
Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.
❑
Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑
Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself. If the product needs to be repaired, consult your dealer or an authorized Panasonic Service center.
❑
Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign matter in it, is exposed to water,
is smoking, or smells), turn it off immediately and consult
your dealer.
❑
The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the floor
while driving, get wedged under the brake pedal, and lead to
a traffic accident.
❑
Refer fuse replacement to qualified service personnel.
When the fuse burns out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may lead
to smoke, fire, and damage to the product.
Observe the following warnings when
installing.
❑
Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY OR DEATH.
❑
Never use safety-related components for installation, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
❑
Installing the product on the air bag cover or in a
location where it interferes with airbag operation is
prohibited.
❑
Check for piping, gasoline tank, electric wiring, and
other items before installing the product.
If you need to open a hole in the vehicle chassis to attach or
wire the product, first check where the wire harness, gasoline tank, and electric wiring are located. Then open the hole
from outside if possible.
❑
Never install the product in a location where it interferes with your field of vision.
❑
Never have the power cord branched to supply other
equipment with power.
❑
After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑
In the case of installation to an airbag-equipping
car, confirm warnings and cautions of the vehicle
manufacturer before installation.
❑
Make sure the leads do not interfere with driving or
getting in and out of the vehicle.
❑
Insulate all exposed wires to prevent short circuiting.
Caution
Observe the following cautions when using this
unit.
❑
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
❑
Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.
❑
This unit is designed for use exclusively in automobiles.
❑
Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑
Do not expose the unit to direct sunlight or excessive heat.
Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.
❑
Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on rainy
days.
Observe the following cautions when
installing.
❑
Refer wiring and installation to qualified service
personnel.
Installation of this unit requires special skills and experience.
For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from your
own installation of the unit.
❑
Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑
Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws, and
moving parts such as seat rails. Do not scratch, pull, bend or
twist the leads. Do not run them near heat sources or place
heavy objects on them. If leads must be run over sharp
metal edges, protect the leads by winding them with vinyl
tape or similar protection.
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit.
Faulty installation may lead to an accident, a malfunction or
fire.
❑
Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
❑
Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
❑
Installation Angle
The product should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit must be installed.
Consult your dealer for further details.
❑
Wear gloves for safety. Make sure that wiring is
completed before installation.
❑
To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑
Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling
the batteries for the remote control unit.
●
Use only specified battery (CR2025).
●
Match the polarity of the battery with the (+) and (–) marks
in the battery case.
●
Replace dead battery as soon as possible.
●
Remove the battery from the remote control unit when not
using it for an extended period of time.
●
Insulate the battery (by placing them in a plastic bag or covering them with vinyl tape) before disposal or storage.
●
Dispose of the battery according to the local regulations.
●
Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.
In case of battery leakage
●
Thoroughly wipe the battery liquid off the battery case and
insert new battery.
●
If any part of your body or clothing comes into contact with
battery liquid, wash it with plenty of water.
●
If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical attention.
■
Read the operating instructions for the unit and all other components of your car audio system carefully before using the
system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no
responsibility for any problems resulting from failure to
observe the instructions given in this manual.
■
This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
Warning Caution
This pictograph intends to alert you to the presence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in severe injury or death.
This pictograph intends to alert you to the presence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material damage.
4
CQ-C9901W/C9801W
5
English
CQ-C9901W/C9801W
Safety Information, Before Reading These Instructions
Safety Information
Accessories
Notes:
¡ The number in parenthesis underneath each accessory part name is the part number for maintenance and service.
¡ Accessories and their parts numbers are subject to modification without prior notice due to improvements.
¡ Mounting Collar and Trim Plate are mounted on the main unit at shipment.
Power Connector
(YEAJ02871)
Q'ty: 1
Lock Cancel Plate
Q'ty: 2
Mounting Bolt
Q'ty: 1
Tapping Screw
(5 mmø x 16 mm)
Q'ty: 1
Hexagonal Nut
(5 mmø)
Q'ty: 1
Mounting Collar
(YEFXO217222)
Q'ty: 1
Removable Face Plate
Case
(YEFA131646)
Q'ty: 1
SEL
SRC
BAND
MUTE
VOL
DISP
Remote Control Unit
(Includes a battery:
CR2025)
(EUR7641010)
Q'ty: 1
Trim Plate
(YEFC05606):
CQ-C9801W
(YEFC05655):
CQ-C9901W
Q'ty: 1
Installation kit (YEP0FZ5701)
Before Reading These Instructions
Label Indications and Their Locations
CAUTION
LASER RADIATION WHEN OPEN. DO NOT STARE
INTO BEAM.
Caution
THIS PRODUCT IS A CLASS 1 LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY
YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Do not take apart this unit or attempt to
make any changes yourself.
This unit is a very intricate device that uses a laser
pickup to retrieve information from the surface of
compact discs. The laser is carefully shielded so that
its rays remain inside the cabinet.
Therefore, never try to disassemble the player or alter
any of its parts since you may be exposed to laser
rays and dangerous voltages.
CLASS 1 LASER PRODUCT
Deck Ass’y (Upper Side)
Laser Product
CQ-C9901W
WMA MP3 CD Player/Receiver with 512 Color OEL
(Organic electroluminescence) Display
CQ-C9801W
WMA MP3 CD Player/Receiver with Full Dot Matrix
Display
This operating instruction manual is for 2 models CQ-C9901W and CQ-C9801W.
The difference among these models’ are mentioned below.
All screens and main body illustrations in this book represent CQ-C9901W unless otherwise specified.
CQ-C9901W CQ-C9801W
Display unit 512 Color OEL Full Dot Matrix (Light Blue)
Features
Models
Before Reading These Instructions
Differences
among 2 models
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected
components, and assembled by people who are proud of the reputation their work has built for our company. We know this product
will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be
proud to be a member of our family.
Operating Instructions
(YEFM285648)
Q'ty: 1
Installation Instructions
(YEFM293973)
Q'ty: 1
Rear Support Strap
(YEFG04019)
Q'ty: 1
CAUTION - LASER
RADIATION WHEN
OPEN. AVOID EXPOSURE TO BEAM.
ЗзаеДзаЦ – гДбЦкзйЦ
абгмуЦзаЦ ика
йндкхнаа. абЕЦЬДнъ
ЗйбСЦвлнЗаь
гДбЦкзйЙй
абгмуЦзаь.
注意－打開時避免被激
光輻射光束照射到。
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
POWER
SOURCE
MENU
SEL
SEL
SRC
SRC
VOL
VOL
SET
BAND
MUTE
BAND MUTE
2 31
231
SCAN REPEAT
RANDOM
5
64
5
64
97
97
8
8
TUNE TUNE
0
0
DISP
DISP
#
#
NUMBER
CAR AUDIO
6
CQ-C9901W/C9801W
7
CQ-C9901W/C9801W
Contents
¡Safety Information 2
¡Before Reading These Instructions 4
¡Features 6
¡Controls Layout 8
¡Preparation 10
¡General 12
¡Sound Control 16
¡Radio 19
¡CD Player 22
¡MP3/WMA Player 24
¡Disc Changer
(when CDs or MP3 discs are loaded)
28
¡Disc Changer (when DVDs or VCDs are loaded) 30
¡Audio Setting 32
¡Function Setting 34
¡Display Setting 35
¡Customize the Display 36
¡Troubleshooting 38
¡Error Display Messages 42
¡Notes on Discs 43
¡Maintenance 44
¡Contents by Functions 44
¡Specifications 45
Features
English
46
90
CommonEach SourceAs Needed
New Features
Full Digital CD Receiver
The CQ-C9901W/C9801W uses Radio DSP for digital
conversion and processing of FM/AM signals, and a
digital amp to provide amplification of the digital data.
With this technology, Panasonic achieves full digital
processing of radio and CD signals from input to speaker
output. This means faithful reproduction of the original
sound.
Radio DSP
By digitally converting and processing FM/AM broadcast
signals, this greatly reduces adjacent interference and
multipath distortion.
A radio's IF filter has the job of preventing neighboring
broadcast frequencies from interfering with reception of
your desired station. Panasonic's Radio DSP uses an
advanced algorithm to perform this task with digital
control. It maintains the optimum balance between noise
suppression and sound quality by automatically adjusting
the IF filter bandwidth in response to the changing
interference characteristics as you drive.
Fully Motorized Front Panel
A touch is all it takes to slide the front panel down for
access to the disc slot. A three-stage tilt function permits
viewing angle to be adjusted to 15, 25 or 35 degrees for
optimum display visibility.
256x64 pixel 512-color OEL display
(CQ-C9901W only)
Multicolored expression can be achieved thanks to OEL
display. You can use this unit in your original way in collaboration with the customization function.
Sound Control
CS Auto (CIRCLE SURROUND AUTOMOTIVE)
CS Auto allows your car interior to change to a splendid
audio room in a moment. Every speaker can be finetuned. (a page 16)
*CS Auto, TruBass, FOCUS, SRS and symbol are
trademarks of SRS Labs, Inc.
CS Auto technology is incorporated under license from
SRS Labs, Inc.
Note: If you enable CS Auto, the following functions are
automatically disabled:
SQ, POSITION, BASS/TREBLE, BALANCE/FADER, SUBWOOFER LEVEL, LPF, HPF, SBC-SW
SQ (SOUND QUALITY)
You have six preset modes (FLAT, POP, ROCK, VOCAL,
JAZZ, CLUB). You can customize your settings for these
(except FLAT) and save them for instant recall.
SQ9 (9-Band Sound Quality)
Center frequency and level are adjustable in each of nine
bands. This lets you fine tune sound quality for each
genre to suit car-interior acoustics and your personal
preferences. (a page 16)
Full lineup of optional parts
You can also enjoy watching DVDs if the optional DVD
changer and display unit are connected.
New radio tuner
Innovated APM (Auto Preset Memory) method for FM
bands. In addition to the conventional method (EACH
BAND), we have successfully launched the enhanced ALL
BAND method that presets 18 stations at the same time.
(a page 21)
Delightful sound space thanks to system buildup
Sub-Woofer
(Option)
CQ-C9901W/C9801W
Head unit
Stereo/Mono
Power Amplifier (Option)
DVD Changer
CX-DH801W
(Option)
Monitor: CY-VM1500EX
(Option)
8
CQ-C9901W/C9801W
9
English
CQ-C9901W/C9801W
y / 5 PAUSE/PLAY
BAND
SET
APM
AUTO PRESET MEMORY
Controls Layout
Note: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
SRC
CS
SEL
SRC
BAND
MUTE
VOL
DISP
One-touch operation is available for selecting a track
playing style by use of [4] (RANDOM), [5] (SCAN), or
[6] (REPEAT). (For a Folder/Disc playing style, hold
down the same button for 2 sec. or more.)
Direct Access
A track (CD mode), disc (Disc changer), file and folder
(MP3/WMA mode) can be directly selected.
Example: Track number 5
1
Press [#] (NUMBER).
2
Press [5].
3
Press [BAND] (SET).
SRC SOURCE
PWR POWER
MUTE
SBC·SW SUPER BASS
CONTROL-SUBWOOFER
CS
CIRCLE SURROUND AUTOMOTIVE
SQ SOUND QUALITY
MENU
DIM DIMMER
D•M DIRECT MEMORY
VOLUME
PUSH SEL SELECT
DISP
DISPLAY
TUNE
TRACK
(FILE)
Release
CS
TILT
OPEN (eject)
SRC SOURCE
PWR POWER
MUTE
SBC·SW SUPER BASS
CONTROL-SUBWOOFER
BAND
SET
APM AUTO PRESET
MEMORY
SEL SELECT
MENU
VOL VOLUME
}: Up
{: Down
DISP DISPLAY
8
0
0
RANDOM
SCAN
REPEAT
Number Buttons
to
NUMBER
RANDOM
SCAN
REPEAT
TUNE
TRACK (FILE)
P·SET (PRESET)
DISC (FOLDER)
VOL
DISP
BAND
SET
SEL
MENU
Controls Layout
Main Unit
Remote Control UnitFunctions only by remote control unit
Disc slot
When Panel Opens
P·SET
PRESET
DISC
(FOLDER)
MUTE
SRC
POWER
SOURCE
NUMBER
CS
99
##
NUMBER
NUMBER
RANDOM
RANDOM
44
SCAN
SCAN
55
REPEAT
REPEAT
66
77
99
808
0
POWER
POWER
SOURCE
SOURCE
SRC
SRC
SET
SET
BAND
BAND
MENU
MENU
SEL
SEL
POWER
SOURCE
SRC
SRC
SET
BAND MUTE
BAND
RANDOM
TUNE TUNE
#
#
NUMBER
CAR AUDIO
MENU
SEL
SEL
VOL
VOL
MUTE
2 31
231
SCAN REPEAT
5
64
5
64
97
97
8
8
0
0
DISP
DISP
VOL
VOL
MUTE
MUTE
DISP
DISP
10
CQ-C9901W/C9801W
11
English
CQ-C9901W/C9801W
Preparation
Note: Adjust the clock when “ADJUST” appears on the
display.
1
Press [MENU] to display the menu display.
For using the remote control, hold down [MENU]
for 2 sec. or more.
2
Press []] or [[] to display the DISPLAY menu.
3
Press [{] to select “CLOCK ADJ”.
4
Press [BAND] (SET) to confirm the display.
5
Adjust the setting value.
[[]:Adjusting minutes
[]]
:
Adjusting hours
[}]
:
Forward
[{]
:
Backward
6
Press [BAND] (SET) to confirm the
adjustment.
Note: For cancellation of clock adjustment, press
[DISP].
7
Press [MENU].
For using the remote control, hold down [MENU]
for 2 sec. or more.
When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP] to change to regular mode.
1
Set your car’s ignition switch to the ACC
or ON position.
The demonstration screen appears.
Example: CQ-C9901W
2
Press [DISP: DISPLAY].
The demonstration screen is cancelled, and no more
appears.
Note: If you would like to turn on the power and make
the demonstration message appear, hold down [SRC]
(PWR: POWER) for 4 sec. or more.
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡ Subwoofer level adjustment (a page 32)
¡ Subwoofer low pass filter (a page 32)
Connecting an AV device (TV, VTR)
If you connect TV to AUX1 terminal, set the AUX1 setting
to TV.
1
Press [SRC: SOURCE] to select the
AUX1 mode. (a page 14)
2
Press [MENU] to display the menu display.
For using the remote control, hold down [MENU]
for 2 sec. or more.
3
Press [BAND] (SET) to adjust.
: TV
: Other devices (Default)
Note: When using an external TV unit manufactured by
a third party, select the TV mode.
4
Press [MENU] to confirm the adjustment.
The following functions are activated when the Security
Function is ON. (a page 34)
¡ The security indicator blinks when removing the face
plate.
¡ The alarm sounds and the message appears on the
screen to warn you to remove the face plate at power
off.
Security Indicator
SRC
CS
Preparation
First Time Power On
(DEMONSTRATION)
Remote Control PreparationSecurity Function
Setting
Other SettingsClock adjustment
(CLOCK ADJ: CLOCK ADJUSTMENT)
Battery Replacement
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Warning
¡Keep batteries and insulation film out of reach
of infants. If an infant ingests a battery, please
seek immediate medical attention.
Caution
¡
Remove and dispose of an old battery immediately.
¡ Do not disassemble, heat or short a battery.
Do not throw a battery into a fire or water.
¡ Follow local regulations when disposing of a
battery.
¡Improper use of a battery may cause overheat-
ing, an explosion or ignition, resulting in injury
or a fire.
Note:
¡Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under nor-
mal use (at room temperature)
q
w
q Remove the battery holder
with the remote control unit
placed on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w Pull it out in the direction
of the arrow using a
tough pointed object.
w Put a battery in the case with
(+)-side facing up.
e Put the case back.
2
3
Tough pointed object
Back side
Insulation film
12
CQ-C9901W/C9801W
13
English
CQ-C9901W/C9801W
Power on
Press [SRC] (PWR: POWER).
Notes:
¡ The opening screen appears. You can overwrite the
opening screen (moving picture) with new one. (a
page 36)
¡ When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP] to change to regular mode. (a page 10)
Power off
Hold down [SRC] (PWR: POWER) for 2
sec. or more and release it.
Note: The ending screen appears. You can overwrite the
ending screen (moving picture) with new one. (a page
36)
General
This chapter explains how to turn on or off the power, how to adjust the volume, etc.
You can remove the face
plate to prevent it from
being stolen.
Removing
1
Turn off the power
(a page 12)
2
Press [] (Release).
(The face plate disengages
with a click when it is
removed.)
The face plate automatically closes in 5 seconds if it is open or tilted.
Note: The power is automatically turned off while
the unit is active.
3
Put the face plate in the case.
Mounting
1
Slide the left side of the face plate in
place.
2
Press the right end of the face plate
until “click” is heard.
Caution
¡ It is recommended to remove or mount the face
plate when the plate is at the closed position.
Do not remove or mount the face plate when the
plate is in motion.
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or
nearby areas where the temperature rises to high
levels.
¡ Do not touch the contacts on the face plate or on the
main unit, since this may result in poor electrical
contacts.
¡ If dirt or other foreign substances get on the con-
tacts, wipe them off with clean and dry cloth.
¡ To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
Open/Eject
Press [] (OPEN).
When a disc is already loaded, the disc will automatically
be ejected.
Close
Press [] (OPEN).
Tilt
The display angle changes among 4 levels as follows
every time you hold down [] (TILT) for 1 sec. or
more and release.
Note: The last selected
angle is maintained even
after turning off the power.
Notes:
¡ The volume level can be set independently for each
source. (For radio, one volume setting for AM, one
volume setting for all FMs)
¡ The volume is not adjustable while an error appears
on the monitor or the external mute function is
enabled. (a page 42)
q Up
w Down
Setting Range: 0 to 40
Default: 18
Volume off (down)
Press [](MUTE).
Cancel
Press [](MUTE) again.
Note:
Volume-down range can be specified. (a page
34)
Power On/off
(PWR: POWER)
Face Plate Motion (Open/Close, Tilt)
(OPEN/CLOSE, TILT)
Volume Adjustment
(VOLUME)
Temporary Volume Off (Down)
MUTE (ATT: ATTENUATION)
Caution
¡ To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
¡ Do not pinch your finger or hand in the face plate.
¡ Do not insert foreign objects into the disc slots.
¡ For the following cases, the face plate automatical-
ly closes. Use caution not to catch your finger.
¡ After a lapse of 20 seconds
¡ When a disc is inserted
¡ When the face plate is removed (a page 12)
¡ Five seconds after turning off the power or
turning the key to ACC OFF.
Face Plate Removing/Mounting
(ANTI-THEFT)
SRC
CS
SRC
SRCCSSRC
CS
General
TILT 1
TILT 2
TILT 3
TILT OFF
OPEN
14
CQ-C9901W/C9801W
15
English
CQ-C9901W/C9801W
General
The display changes as follows every time [DISP:
DISPLAY] is pressed.
Note: You can select a graphic pattern and a still image
from originally stored data. (a page 35) You can also use
your original images. (Customize Function a page 36)
At power-off:
Clock display (default)
The dimmer level changes as follows every time you hold
down [MENU] (DIM: DIMMER) for 2 sec. or more.
Brighter (Default)
Medium
Mode
Folder hierarchy (MP3/WMA mode only.)
Ordinary display + still image
Ordinary display + clock
Display OFF
All displays disappear in 5 seconds.
At power-on:
Darker
Off
Only graphic pattern
Only still image
Display Change
(DISP: DISPLAY)
Dimmer Control
(DIM: DIMMER)
Note: This setting is not adjustable with the remote control.
SRCCSSRC
CS
General
Radio
FM1, FM2, FM3, AM (a page 19)
Source Selection
(SRC: SOURCE)
The source changes as follows every time
[SRC: SOURCE] is pressed.
Player
Auxiliary (AUX 1)
Auxiliary (AUX2)
SRC
CS
SRC
When connecting CD Changer, DVD Changer (a page
28, 30)
When connecting a device that is not
compatible with this unit
When loading CD (a page 22)
When loading MP3/WMA disc (a page 24)
When connecting a TV
When connecting a device that is not compatible with
this unit
Notes: Please connect a CD changer or a DVD changer
to AUX2. (a Installation Instructions)
Ordinary display + graphic pattern
Loading...