Panasonic AVHS400N - MULTI FORMAT LIVE SWITCHER Operating Instructions Manual

POWER ALARM

F1 F2 F3 F4 F5

KEY DSK PinP AUX CLN PVW PGM 1 2

USERAUX SOURCEAUX BUS DELEGATION

1 2 3 4 5 6 7 8 9 10

AUX

PGM/A

PST/B

BKGD PATT

KEY PATT

FUNC N/R R

WIPE DIRECTIONWIPE PATTERN / FUNCTION

WIPE SQ

SL 3D

POSITIONER

FTB

PinP

DSKCUT AUTO

MIX WIPE

BKGD KEY

MIX

WIPE

PAGE

AMB:FILL / GRN:SOURCE

Multi-format Live Switcher AV-HS400

TIME WIPE COLOR

KEY CHR KEY FREEZE

DSK PinP IN/OUT

MEMORY XPT SYSTEM

1 2 3

4 5 6

7 8 9

10 12

Operating Instructions

Multi-format Live Switcher

Model No. AV-HS400N

Before operating this product, please read the instructions carefully and save this manual for future use.

Printed in Japan VQTB0308-3

indicates safety information.

This class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

For CANADA

Safety precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance.

WARNING:

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

• THE

APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

FCC Note:

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Warning:

To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also, any unauthorized changes or modifications to this equipment could void the user’s authority to operate it.

CAUTION:

In order to maintain adequate ventilation, do not install or place this unit in a bookcase, built-in cabinet or any other confined space. To prevent risk of electric shock or fire hazard due to overheating, ensure that curtains and any other materials do not obstruct the ventilation.

The socket outlet shall be installed near the equipment and easily accessible or the mains plug or a power switch shall remain readily operable.

A warning that an apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection.

WARNING:

 THIS APPARATUS MUST BE EARTHED

To ensure safe operation, the three-pin plug must

be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords

used with the apparatus must have three cores and be correctly wired to provide connection to the earth. Wrongly wired extension cords are a major cause of fatalities. The f

act that the apparatus operates satisfactorily does not imply that the power point is earthed or that the installation is completely safe. For your safety, if you are in any doubt about the effective earthing of the power point, please consult a qualified electrician.

indicates safety information.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) D

o not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

o not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)

Protect

the power cord form being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)

Only

use attachments/accessories specified by

the manufacturer.

12)

Use only with the cart, stand,

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)

Unplug

this apparatus during lightning storms

or when unused for long periods of time.

14) R

efer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference.

IMPORTANT SAFETY INSTRUCTIONS

Safety precautions

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca/gov/hazardouswaste.perchlorate.

Contents

Description ................................................6

Features .....................................................6

Precautions for use ..................................7

1. Functions in each area .........................8

1-1. Control panel .....................................................8

1-2. Crosspoint area .................................................9

1-3. Wipe area ........................................................10

1-4. User button area ..............................................11

1-5. Transition area .................................................1

1-6. LCD men

u area ...............................................14

1-7. Positioner area ................................................15

1-8. SD memory card area .....................................15

1-9. Rear panel connections area ..........................16

2. System ..................................................18

2-1. Configuration ...................................................18

2-2. Connections ....................................................19

3. Basic operations .................................21

3-1. Background transition ......................................21

3-1-1. Selecting the bus ......................................21

3-1-2

. Selecting the bus mode ............................21

3-1-3. Selecting the transition mode ...................22

3-1-4. Manual transition (using the fader lever) ...22

3-1-5. Auto transition ...........................................22

3-1-6. Cut transition .............................................22

Wipe ................................................................23

3-2-1. Selecting the wipe pattern ........................23

3-2-2. Selecting the wipe direction ......................24

3-2-3. Wipe decorations (border, soft effect) .......24

3-2-4. Setting the wipe start position ...................25

3-2-5. Modifying wipe ..........................................26

3-3. Key ..................................................................27

3-3-1. Selecting the k

ey type ...............................28

3-3-2

. Selecting the key material .........................29

3-3-3. Key transitions ..........................................30

3-3-4. Key preview...............................................31

3-3-5.

Adjusting the luminance key and linear key

...31

3-3-6. Adjusting the chroma key .........................32

3-3-7. K

ey decorations ........................................35

3-3-8. Masking the key signals ............................36

3-4. PinP (picture in picture) ...................................37

3-4-1. Selecting the PinP material ......................37

3-4-2.

PinP transitions .........................................37

3-4-3. PinP preview .............................................37

3-4-4. PinP adjustments ......................................38

3-4-5. PinP decorations .......................................39

3-4-6. Trimming settings ......................................40

3-5. DSK (downstream key)....................................41

3-5-1. Selecting the DSK type .............................41

3-5-

Selecting the DSK material .......................42

3-5-3. DSK transitions .........................................43

3-5-4. DSK preview .............................................43

3-5-5. DSK adjustments ......................................43

3-5-6. DSK decorations .......................................44

3-6. FTB (fade to black) ..........................................45

3-7. Internal color signals .......................................46

3-7-1. Setting the color background ....................46

3-8. Freezing the input signals ...............................47

3-8-1. Displaying the freeze status ......................47

3-8-

Setting freeze ............................................47

3-9. Switching the AUX output ................................48

3-10. Preset memory ..............................................49

3-11. Frame memories ...........................................5

3-11-1.

Transferring images from the AUX bus ...52

3-12

. SD memory cards .........................................53

3-12-1.

Initializing the SD memory cards ............54

3-12-

2. Saving data on SD memory cards ..........54

3-12-3.

Loading data from SD memory cards .....55

Contents

4. Input/output signal settings...............56

4-1. Setting the SDI input signals and analog input

signals .............................................................56

4-1-1. Setting the frame synchronizer .................56

4-1-2.

Setting the input mode ..............................57

4-1-3. Setting the analog input gain ....................58

4-2.

Setting the up-converter (option) .....................58

4-3. Setting the DVI input signals (option) ..............59

4-3-1. Setting the DVI input signals .....................59

4-3-2.

Adjusting the DVI input signals .................61

4-4. Setting the output signals ................................62

4-4-1.

Types of output signals .............................62

4-4-2

. Assigning the output signals .....................62

4-5. Setting the sync signals...................................63

4-6. Adjusting the output signal phase ...................64

4-7. Setting the multi view display ..........................66

4-8. Setting the on-screen display (OSD) ...............68

4-9. Setting the DVI output signals (option) ............69

4-10. Setting the ancillary data ...............................70

5. System settings ..................................71

5-1. Selecting the video format ...............................71

5-2. Setting the crosspoints ....................................72

5-2-1. Assigning signals to the crosspoints .........72

5-2-2. Setting the crosspoint switching ...............73

5-3. Button assignments .........................................74

5-3-1. Setting the user buttons ............................74

5-3-2.

Setting the FTB button ..............................74

5-4. Setting the date and time ................................75

5-5. Network settings ..............................................76

5-6. Other settings ..................................................77

5-6-1. Setting the LCD backlight .........................77

5-6-

Setting editor enable .................................77

5-6-3. Setting the GPI .........................................78

5-7. Status displays ................................................79

5-7-1. Alarm status displays ................................79

5-7-2.

Displaying the version information and

option information .....................................80

5-8. Initialization......................................................81

6. External interfaces .............................82

6-1. RS-422 connector ...........................................82

6-2. GPI connector .................................................83

6-3. Tally connector.................................................84

7. Setting menu table ..............................85

8. Appearance .........................................91

9. Specifications and standar

accessories .........................................92

Appendix (glossary) ...............................95

Description

This is a 1 ME digital video switcher which supports a multiple number of HD and SD formats. Despite its compact dimensions, the video switcher comes standard with 4 input connectors and can support 8 input connectors when an option board is used. It also has a multi-view display function that allows split-screen display with up to 10 screens. It is capable of providing transitions (wipe, mix and DVE) as video effects, and keyer (luminance keys and chroma keys), DSK and PinP specialized hardware is provided as a standard feature to enable video productions in many different forms. The unit also supports SD memory cards so still image data (BMP) can be imported from SD memory cards into the unit’s frame memories for use as background images or key materials.

Features

Compact design, wide variety of input/output signals

 As a standard feature

, the HD and SD-SDI formats are supported for the input and output signals. If an optional board is added, HD/SD analog component and DVI-I signals can also be accommodated. The input optional board contains an up-converter.



Under the standard specifications, there are four SDI lines for the input signals, and this number can be optionally increased by the user up to eight lines (supported by the optional board). Similarly, there are three SDI lines for the output signals under the standard specifications, and this number can be optionally increased by the user to five lines (PGM, PVW, AUX, KEYOUT and multi view displpay).

Multiple formats supported

Both HD formats (1080/59.94i, 1080/50i, 7

20/59.94p and 720/50p) and SD formats (480/59.94i and 576/50i) as

well as the DVI-I format are supported for the signals.

Multi view display function

This unit enables up to 10 lines of program video (PGM), preview video (PVW) and input video signals to be displayed altogether on a single screen at the same time.

Frame synchronizer system and external synchronization system supported

 A high-performance 10-bit frame synchronizer is incorporated for all the inputs, and asynchronous video

signals can be input. By using the black burst (BB) output, it is possible to construct a system referenced to the synchronization of the switcher.



A genlock function is provided, and an external synchronization system using external sync signals (BB or TRI signals) as a reference are also supported.

Many different effect functions incorporated

 Along with the standard wipe, mix and cut functions

, the unit can provide size reduction, slide and other DVE

transitions.



The unit comes with luminance ke

ys and chroma keys are provided as keyers as well as specialized hardware in the form of the DSK (downstream key) and PinP (picture in picture) functions as a standard option, enabling video productions in many different forms.

SD memory cards supported

Still image data (BMP) can be imported from SD memory cards into the unit’s frame memories for use as background images or key materials. Conversely, the images or setting data in the unit’s frame memories can be stored on the SD memory cards.

Simple operations

Live transmissions can be delivered speedily thanks to the simple panel layout which enables the various functions to be operated directly. Presetting and other similar operations are performed using menus in the form of on-screen displays (OSD) which appear on the unit’s LCD screen or an external monitor.

Precautions for use

 Handle carefully.

Do not drop the product, or subject it to strong shock or vibration.

Do not carry or move the product by the fader lever. This is important to prevent trouble.

 Use the product in an ambient temperature of 32 °F to 104 °F (0 °C to 40 °C).

Avoid using the product at a cold place below 32 °F (0 °C) or at a hot place above 104 °F (40 °C) because

extremely low or high temperature will adversely affect the parts inside.

 Power off before connecting or disconnecting cables.

Before plugging or unplugging the cables, be sure to switch power off.

 Avoid humidity and dust.

Avoid using the product at a humid, dusty place because much humidity and dust will cause damage to the

parts inside.

 Maintenance

Wipe the product using a dry cloth. To remove stubborn dirt, dip a cloth into a diluted solution of kitchen

detergent, wring it out well, and wipe the product gently. Then, after wiping the product with a moist cloth, wipe it again with a dry cloth.

• Avoid using benzine, paint thinners and other volatile fluids.

• If a chemical cleaning cloth is to be used, carefully read through the precautions for its use.

Caution

 Precaution to be observed during production

This product’s image switching and image effect functions can be used to produce images which flicker rapidly

or images which change rapidly.

How

ever, bear in mind when using these functions in production that the kinds of images produced may have

an adverse effect on the viewer’s physical well-being.

 Handling the optional boards

Be absolutely sure to turn off the power of the product before installing or removing any of the optional boards. Furthermore, when installing or removing the optional boards, take care not to hurt yourself on the edges and

metal parts of the boards.

 When the product is to be discarded

When the product is to be discarded at the end of its service life, ask a specialized contractor to dispose of it

properly in order to protect the environment.

1. Functions in each area

1-1. Control panel

POWER ALARM

F1 F2 F3 F4 F5

KEY DSK PinP AUX CLN PVW PGM 1 2

USERAUX SOURCEAUX BUS DELEGATION

1 2 3 4 5 6 7 8 9 10

AUX

PGM/A

PST/B

BKGD PATT

KEY PATT

FUNC N/R R

WIPE DIRECTIONWIPE PATTERN / FUNCTION

WIPE SQ

SL 3D

POSITIONER

FTB

PinP

DSKCUT AUTO

MIX WIPE

BKGD KEY

MIX

WIPE

PAGE

AMB:FILL / GRN:SOURCE

Multi-format Live Switcher AV-HS400

TIME WIPE COLOR

KEY CHR KEY FREEZE

DSK PinP IN/OUT

MEMORY XPT SYSTEM

1 2 3

4 5 6

7 8 9

10 12

 

User button area

LCD menu area SD memory card area

Positioner area

Wipe pattern area

Transition areaCrosspoint area

 Power indicator [POWER]

This indicator lights when the power switch (_) on the rear panel is set to ON while power is supplied to the AC power input socket. It goes off when the power switch (_) is set to OFF.

2 Alarm indicator [ALARM]

This indicator lights when the fan is stopped or there is a problem with the power supply (such as a drop in voltage). When an alarm has occurred, the type of trouble can be checked on the System/Alarm (6/14) menu. In addition, an alarm message is displayed on the OSD screen of the LCD screen and the external monitor.

ALARM TYPE System/Alarm (6/14) ALARM MESSAGE

Fan alarm Alarm display in Fan items ALARM! FAN STOP Power alarm Alarm display in Power items ALARM! POWER FAILURE

Power alarm and fan alarm

Alarm display in Fan items and Power items

ALARM! POWER FAILURE & FAN STOP

If the alarm goes off, stop using the unit immediately and be sure to contact your dealer. Continuing to use the unit even after the alarm goes off could damage it.

1. Functions in each area

1-2. Crosspoint area

F1 F2 F3 F4 F5

KEY DSK PinP AUX CLN PVW PGM 1 2

USERAUX SOURCEAUX BUS DELEGATION

1 2 3 4 5 6 7 8 9 10

AUX

PGM/A

PST/B

AMB:FILL / GRN:SOURCE











3 PGM/A bus crosspoint buttons [PGM/A 1 to 10]

These are used to select the PGM/A bus video signals. In the case of the flip-flop system, the main line video (PGM) signals are always selected.

4 PST/B bus crosspoint buttons [PST/B 1 to 10]

These are used to select the PST/B bus video signals. In the case of the flip-flop system, the images inserted next (PST) are always selected.

5 AUX bus selector buttons [KEY, DSK, PinP, AUX]

Press the KEY button, DSK button, PinP button or AUX button to switch the bus which is selected using the AUX bus crosspoint buttons (7). The indicator of the button that was pressed lights.

[KEY]: Press this button to s

witch the AUX bus crosspoint buttons to the key fill bus or key source bus. (Each time the button is pressed, the key fill bus or key source bus is selected alternately. When the key fill bus is selected, the indicator of the button lights in amber, and when the key source bus is selected, it lights in green.)

[DSK]:

Press this button to s

witch the AUX bus crosspoint buttons to the DSK fill bus or DSK source bus. (Each time the button is pressed, the DSK fill bus or DSK source bus is selected alternately. When the DSK fill bus is selected, the indicator of the button lights in amber, and when the DSK source bus is selected, it lights in green.)

[PinP]:

Press this button to s

witch the AUX bus crosspoint buttons to the PinP bus.

[AUX]: Press this button to s

witch the AUX bus crosspoint buttons to the AUX bus.

6 AUX bus dedicated crosspoint buttons [CLN, PVW, PGM]

These buttons are used to select the AUX bus source while the indicator of the [AUX] button is lighted. The indicator of the pressed button lights in amber.

[CLN]: The clean signals (images whose DSK signals hav

e been removed from the PGM signals) are

output to the AUX bus.

[PVW]: PVW signals are output to the AUX bus

[PGM]: PGM signals are output to the AUX bus

7 AUX crosspoint buttons

These buttons are used to select the source of the bus which was selected by the [AUX] bus selector button (5).

1. Functions in each area

1-3. Wipe area

8 Wipe pattern selector buttons

These 12 buttons are used to select the corresponding wipe patterns while the indicator of the [BKGD PATT] button (9) or KEY PATT button (9) is lighted. They are used to select the corresponding setting menus when the indicator of the FUNC button (;) is lighted. The indicator of the selected button lights in amber.

BKGD PATT

KEY PATT

FUNC

WIPE PATTERN / FUNCTION

WIPE SQ

SL 3D

PAGE

TIME WIPE COLOR

KEY CHR KEY FREEZE

DSK PinP IN/OUT

MEMORY XPT SYSTEM

1 2 3

4 5 6

7 8 9

10 12

 







9 BKGD, KEY pattern selector buttons

These buttons are used to switch the wipe pattern selection. The wipe pattern of a background transition is selected when the indicator of the [BKGD PATT] button is lighted after it was pressed. The wipe pattern of a key transition is selected when the indicator of the [KEY PATT] button is lighted after it was pressed. Each time the [BKGD PATT] button or [KEY PATT] button is pressed, the pattern page is changed in the sequence of WIPE, SQ (squeeze), SL (slide) and 3D (3 dimensions), and the pattern page indicator LED (:) is also switched. 3D cannot be selected using the [KEY PATT] button.

: Pattern page indicator LEDs

These LEDs indicate the pages selected by the background transitions while the indicator of the [BKGD PATT] button is lighted. They indicate the pages selected by the key transitions while the indicator of the [KEY PATT] button is lighted. The WIPE, SQ (squeeze), SL (slide) or 3D (3 dimensions) LED lights.

; FUNC button

When this button is pressed, its indicator lights in amber. When a wipe pattern selector button (8) is pressed while the indicator of the FUNC button is lighted, the setting menu indicated below the button is displayed on the LCD screen.

[TIME]:

The auto transition time settings are perf

ormed.  See 3-1-5.

[WIPE]: The modify, border or soft eff

ect decoration settings are performed for wipe.  See 3-2.

[COLOR]: The color backg

round settings are performed.  See 3-7.

[KEY]: The ke

y settings are performed.  See 3-3.

[CHR KEY]: The chroma ke

y settings are performed.  See 3-3-6.

[FREEZE]: The freeze status is displa

yed and freeze settings are performed.  See 3-8.

[DSK]: DSK settings are perfor

med.  See 3-5.

[PinP]: PinP settings are perfor

med.  See 3-4.

[IN/OUT]: The input/output signals are set.  See 4. [MEMOR

Y]: The preset memory

, frame memory or SD card memory settings are performed.

 See 3-10, 3-11 and 3-12.

[XPT]:

The crosspoint assignment is display

ed and set.  See 5-2.

[SYSTEM]: The system settings are perfor

med.  See 5.

< Freeze status indicator LED

When this LED is lighted, it means that one of the input signals is in the freeze status. The freeze status of the input signals assigned to the crosspoint buttons can be checked on the menu.  See 3-8. Since the freeze status is established while this indicator is lighted, the input image handled inside the unit will remain unchanged even when a different image is input.

1. Functions in each area

1-4. User button area

1 2

USER



= User buttons [USER 1, USER 2]

These are used to allocate some functions of the menu settings to the USER 1 button and USER 2 button.  See 5-3-1.

1. Functions in each area

1-5. Transition area

KEY PATT

FUNC N/R R

WIPE DIRECTIONWIPE PATTERN / FUNCTION

FTB

PinP

DSK

CUT AUTO

MIX WIPE

BKGD KEY

MIX

WIPE

DSK PinP IN/OUT

MEMORY XPT SYSTEM

7 8 9

10 11 12











 

 







 

> [BKGD] button

This executes the background transition when the [AUTO] button (D) or fader lever (J) has been operated. When the [BKGD] button is pressed and it is selected, its indicator lights in amber. If the [KEY] button (?) is now pressed, the indicator goes off, and the de

-selected status is established. When the [BKGD] button and [KEY] button (?) are pressed at the same time, both buttons are set to the selected status.

? [KEY] button

This executes the key transition when the [AUTO] button (D) or fader lever (J) has been operated. When the [KEY] button is pressed and it is selected, its indicator lights in amber. If the [BKGD] button (>) is now pressed, the indicator goes off, and the de-selected status is established. When the [BKGD] button (>) and [KEY] button are pressed at the same time, both buttons are set to the selected status.

@ KEY ON tally LED

This lights in red when the key ON status is established.

A MIX, WIPE selection status tally LEDs

These light up to indicate whether MIX or WIPE has been selected when background transitions or key transitions are executed.

B [MIX] button

This is used to switch the A and B bus images while making them overlap. During the transition, the A and B bus output total is kept at 100 %. When the [MIX] button is pressed and it is selected, its indicator lights in amber. If the [WIPE] button (C) is now pressed, it goes off, and the de-selected status is established.

C [WIPE] button

This is used to execute the transition using the pattern selected by the wipe pattern selector button (8). When the [WIPE] button is pressed and it is selected, its indicator lights in amber. If the [MIX] button (B) is now pressed, it goes off, and the de-selected status is established.

1. Functions in each area

D [AUTO] button

This is used to automatically execute transitions (auto transition) using the transition time which has been set. During auto transition its indicator lights in amber. When the button is pressed again during auto transition, the auto transition operation is suspended, and the indicator lights in green. When it is pressed again while auto transition is suspended, the remaining transition is executed. The indicator goes off when auto transition is completed. When the [AUTO] button is pressed while the fader lever (J) is at an interim setting, the transition is executed in the time remaining from the interim setting.

E [CUT] button

This button is used to execute transitions instantly. Its indicator lights in amber during a transition, and it goes off when the transition is completed.

F [FTB] button

This button is used to execute fade-out to a black screen or fade-in from a black screen for the transition time which has been set.

G [PinP] button

This button is used to execute fade-in or fade-out of the picture in picture for the transition time which has been set.

H [DSK] button

This button is used to execute fade-in or fade-out of downstream key for the transition time which has been set.

I Wipe direction selection buttons

These buttons are used to select the direction in which to wipe for executing background transitions.

When the indicators are off:

Wiping proceeds in the normal direction.

When the [R] indicator is lighted:

Wiping proceeds in the reverse direction.

When the [N/R] indicator is lighted:

The normal direction is replaced with the reverse direction (or vice versa) when the transition is

completed. (The lighted and extinguished statuses of the [R] button are also switched in line with the direction of the wiping.)

J Fader lever

This is used to execute background or key transitions. When it is moved as far as it will go, the transition is completed. When it has been operated during auto transition, auto transition will be switched to manual operation as soon as the fader position overtakes the amount of the transition being executed.

K Bus tally LEDs

These indicate the output statuses of the A bus and B bus. The LED corresponding to the bus whose program signals (PGM) are being output lights.

1. Functions in each area

1-6. LCD menu area

POWER ALARM

F1 F2 F3 F4 F5





L LCD

The setting menus are displayed on the LCD. When the [FUNC] button (;) is pressed and its indicator is lighted and then one of the wipe pattern selector buttons (8) is pressed, the setting menu is displayed. When the buttons listed below are double-clicked, the specified menu is selected. (The menu delegation function) The operation corresponding to the button pressed is also executed.

Button Menu

Crosspoint area (AUX bus selector buttons)

KEY KEY menu/Adjust sub menu (

2/8)

CHR KEY menu/Auto sub menu (1/3) (with chroma key selection)

DSK DSK menu/Adjust sub menu (

2/5)

PinP PinP menu/Position sub menu (4/6)

Transition area BKGD TIME menu/BKGD sub menu (1/5)

KEY TIME men

u/KEY sub menu (

2/5)

WIPE WIPE menu/Border sub menu (1/5)

Wipe area WIPE #5 WIPE menu/WIPEPos sub menu (3/5) (BKGD or KEY)

SQ #5 WIPE menu/SQPos sub menu (4/5) (BKGD or KEY)

M Rotary encoders [F1] to [F5]

These are used to set the parameters displayed on the menus (LCD screen or external monitor). For details on the operations, refer to the sections in “3. Basic operations”.

[F1]: Rotate this rotary encoder to s

witch the sub menu.

[F2] to [F5]: Rotate these rotary encoders to set the par

ameters. When the down arrow (↓) is shown at a menu item, its parameter is set by pressing the corresponding rotary encoder. When the parameter is one which is set using a numerical value, its default will be restored when the rotary encoder is held down. (However, the network settings and date and time settings will not be returned to the defaults.)

Adjust Clip Gain Density Invert 2/8 0.0 100.0 100.0 Off

Operate here

using [F1].

Operate here

using [F2].

Operate here

using [F3].

Operate here

using [F4].

Operate here

using [F5].

Sub menu Parameter setting area

1. Functions in each area

1-7. Positioner area

POSITIONER





N Positioners [X/Y]

This is used to set the PinP position or wipe start position (WIPE and SQ #5) or to select the chroma key area. It takes effect only when the menu is selected. The center values of the positioners are set during the time it takes for the unit to start up after its power is turned on. Do not operate the positioners until after the switcher has started up.

O Rotary encoder [Z]

This is used to set the PinP size or to select the chroma key area. In either case, it takes effect only when the menu is selected.

PinP Wipe Chroma key

Positioner X/Y Position adjustments Start position

adjustments

Selected area position adjustments

Rotary encoder Z Size adjustments

(size increased by rotating the encoder clockwise and reduced by rotating it counterclockwise)

— Selected area size adjustments

(size increased by rotating the encoder clockwise and reduced by rotating it counterclockwise)

Switch Hold switch down to restore

initial values (X/Y, Z).

Hold switch down to restore initial values (X/Y).

Hold switch down to restore initial values (X/Y, Z).

Valid menu All PinP menus WIPE/WIPEPos

WIPE/SQPos

CHR KEY/Auto (only when Marker item is set to On)

1-8. SD memory card area

P SD memory card slot

The SD memory card (sold separately) is inserted into this slot.



SD Logo is a trademark.

Q SD memory card access LED

This LED lights while the data on the SD memory card is being accessed. Do not turn off the unit’s power or eject the SD memory card while the access LED is lighted. Doing so can damage the data on the SD memory card.



Concerning the recommended SD cards

Use of the f

ollowing SD memory cards made by Panasonic is recommended.

RP-SD128B

U1A RP-SD256BU1A RP-SDR512U1A RP-SDR01GU1A RP-SDM02GU1A

1. Functions in each area

1-9. Rear panel connections area

POWER

REF

SLOT2

SLOT

34 SLOT1

SLOT2 8

～IN

SDI INPUTS

TALLY

INPUTS

SDI OUTPUTS

INOUT

OUTPUTS

5 7

SLOT

OFF

SLOT1 5

SLOTSLOT

PGM

RS-422LAN

ANALOG INPUTS

Y Pb

DVI INPUTS

ANALOG OUTPUTS

Y Pb

DVI/ANALOG OUTPUTS

Y Pb

DVI-I

DVI-I DVI-I

GPI

SIGNAL

GND





       



 



R SDI signal input connectors [DIGITAL INPUTS 1 to 4]

IN: SDI signal input; OUT: active through output (use this as a monitor output application).

S Optional input connector SLOT1 [INPUT 5, 6] (optional) T Optional input connector SLOT2 [INPUT 7, 8] (optional)

A board (with built-in up-converter), whether an SDI input board, analog input board or DVI input board, can be connected to each of these slots. For further details, refer to the operating instructions of the optional board concerned.

U SDI signal output connectors [DIGITAL OUTPUTS PGM, OUTPUT 1, 2]

PGM: PGM output connectors OUTPUT 1, 2: The signals for these connectors can be assigned using a menu.

V Optional output connector SLOT1 [OUTPUT 3, 4] (optional)

A board, whether an analog output board or DVI/analog output board (OUTPUT3: DVI, OUTPUT4: analog), can be connected to this slot. For further details, refer to the operating instructions of the optional board concerned.

W Optional output connector SLOT2 [OUTPUT 5, 6] (optional)

A board, whether an analog output board or DVI/analog output board (OUTPUT5: DVI, OUTPUT6: analog), can be connected to this slot. For further details, refer to the operating instructions of the optional board concerned.

X Reference input connector/BB output

connector [REF]

Loop-through output in the external sync mode. If the loop-through output is not going to be used, provide a 75-ohm termination. BB signals output from both connectors in the internal sync mode.

External synchronization signal input

Loop-through output

REF

Input the external synchronization signal to the upper of the two connectors shown above.

1. Functions in each area

Y LAN connector [LAN] (RJ-45) (10BASE-T, 100BASE-TX) Z RS-422 interface connector [RS-422] (D-sub 9-pin, female)

 For details on connection, refer to “6. External interfaces”.

[ Tally output connector [TALLY] (D-sub 15-pin, male)

 For details on connection, refer to “6. External interfaces”.

\ GPI input connector [GPI] (3.5 mm diameter stereo mini jack)

 For details on connection, refer to “6. External interfaces”.

] Ground connector

Connect to the system’s earth ground.

^ AC power input socket [AC IN] (AC 100V-120V)

Connect one end of the supplied power cable to this socket and the other end to the AC outlet. The supplied power cable comes with a 3-pin power plug. Be absolutely sure to plug it into a 3-point power outlet as the power source in order to earth the unit securely. If a 3-point power outlet is not available for this connection, be absolutely sure to consult your dealer.

_ Power switch

This is used to turn the power on and off.

2. System

2-1. Configuration

AV-HS400

PGM

PVW

AUX

Multi

KeyOut

INPUT1(SDI) INPUT2(SDI) INPUT3(SDI) INPUT4(SDI)

INPUT5 UC

UC UC

INPUT6

INPUT7 INPUT8

Black ColorBGD ColorBar FMEM1 FMEM2

REF

PGM1, 2(SDI) OUTPUT1(SDI) OUTPUT2(SDI)

OUTPUT4

OUTPUT3

OUTPUT6

OUTPUT5

PGM1, 2

OUTPUT

1, 2

OUTPUT

5, 6

OUTPUT

3, 4

VIDEO INPUT VIDEO OUTPUT

INTERNAL VIDEO

CONTROL

Output Matrix

INPUT

1–4

INPUT

7, 8

INPUT

5, 6

REF IN/OUT(1)

SD Memory Card

RS422 GPI TALLY OUT LAN

: Option

REF OUT(2)

INPUT SLOT1(Option)

OUTPUT SLOT1(Option)

OUTPUT SLOT2(Option)

INPUT SLOT2(Option)



1: When external synchronization is

selected as the ref

erence signal setting, the reference signal is input. When internal synchronization is selected, the reference signal is output.



2: When external synchronization is

selected as the reference signal setting, the signals are looped through and output. When internal synchronization is selected, the reference signal is output.

Table of optional boards

Board Model number Function Where connected

SDI Input Board AV-HS04M1 SDI input ×2 lines INPUT SLO

T1 or

SLOT2

Analog Input Board AV-HS04M

2 Analog component input ×2 lines

DVI Input Board AV-HS04M3 DVI-I input ×2

lines

Analog Output Board AV-HS04M4 Analog component output ×2 lines OUTPUT SLO

T1 or

SLOT2

DVI/Analog Output Board AV-HS04M5 DVI output ×1 line

Analog component output ×1 line

2. System

2-2. Connections

 Connections when implementing gen-lock

(frame synchronizer OFF)



When the unit is to be installed and when the connections are to be performed, be absolutely

sure to ask your dealer to be responsible for carrying out the work that needs to be done.



Use a 3-point power outlet as the power source in order to earth the unit securely.

POWER

REF

GPI

SLOT2

SLOT

34 SLOT1

SLOT2 8

～IN

SDI INPUTS

TALLY

INPUTS

SIGNAL

SDI OUTPUTS

GND

INOUT

OUTPUTS

5 7

SLOT

OFF

SLOT1 5

SLOTSLOT

PGM

RS-422LAN

Power cord (AC100V - 120V, 50/60Hz)

VTR

HD SDI

HD SDI monitor

Multi-format live switcher

AV-HS400N

HD SDI

HD camera

HD SDI

HD camera

HD SDI

HD camera

HD SDI

Signal Generator

HD SDI

HD SDI monitor

HD SDI

HD SDI monitor

2. System

 Connections when not implementing gen-lock

(frame synchronizer ON)

• Example where the optional board is used

POWER

REF

GPI

SLOT2

SLOT

34 SLOT1

SLOT2 8

～IN

SDI INPUTS

TALLY

INPUTS

SIGNAL

SDI OUTPUTS

GND

INOUT

OUTPUTS

5 7

SLOT

OFF

SLOT1 5

SLOTSLOT

PGM

RS-422LAN

ANALOG INPUTS

Y PbPrY Pb

DVI INPUTS

ANALOG OUTPUTS

Y PbPrY Pb

DVI/ANALOG OUTPUTS

Y Pb

DVI-I

DVI-I DVI-I

VTR

PC monitor

HD Component

HD component

monitor

HD SDI monitor

Multi-format live switcher

AV-HS400N

DVD player

HD Component

HD component

monitor

DVI or VGA

HD camera

HD Component

Power cord (AC100V - 120V, 50/60Hz)

HD SDI

VTR

HD SDI

HD camera

HD SDI

HD camera

HD SDI

HD camera

HD SDI

DVI or VGA

HD SDI

DVI or VGA

3. Basic operations

3-1. Background transition

3-1-1. Selecting the bus

Press the crosspoint buttons to select the material which will be targeted for the background transition. By pressing these buttons, the signals are selected, and the indicators of the selected buttons light. The color in which the button indicators light differs depending on the operation status.

Lighting in red:

When the selected input signals are output to PGM.

(How

ever, the indicator lights in amber during FTB operations.)

Lighting in green: When the selected input signals are not output to PGM.

1 2 3 4 5 6 7 8 9 10

PGM/A

PST/B

Lighting in red Lighting in green

3-1-2. Selecting the bus mode

Select the A/B bus system or flip-flop system (PGM/PST system) from the setting menu.

1 Press the [FUNC] button to light its indicator, and then press the [SYSTEM] button to display the SYSTEM

enu.

2 Turn [F1] to display the System sub menu.

Turn [F2], and select the A/B or PGM/PST (flip-flop system) using the BusMode item.

<Men

u display>

System BusMode BL EditEN 2/13 PGM/PST On On

A/B

Off Off

With the flip-flop (PGM/PST) system, the PGM/A bus selected signals are always output as PGM images, and the PST/B bus selected signals are always output as PVW (PST) images.

System Video output Before transition During transition After transition completion

A/B

PGM PGM/A PGM/A, PST/B PST/B

PVW (PST) PST/B PST/B PGM/A

 With an A  B transition

1 2

PGM/A

PST/B

1 2 1 2

Lighting in red Lighting in green

System Video output Before transition During transition After transition completion

Flip-flop

PGM/PST

PGM PGM/A PGM/A, PST/B PGM/A

PVW (PST) PST/B PST/B PST/B

1 2

PGM/A

PST/B

1 2 1 2

Lighting in red Lighting in green

3. Basic operations

3-1-3. Selecting the transition mode

Press the [BKGD] button in the transition area so that its indicator lights in amber. When the [BKGD] button and [KEY] button are pressed at the same time, both buttons are selected.

Use the [MIX] and [WIPE] buttons in the transition area to select the background transition mode. The indicator of the selected button lights in amber.

3-1-4. Manual transition (using the fader lever)

Operate the fader lever to execute transitions manually. If the fader lever has been operated during auto transition, auto transition will be switched to manual operation as soon as the fader position overtakes the amount of the transition being executed. The bus tally LEDs on the left of the fader lever indicate the program bus output status.

Top LED only lights: PGM/A b

us output

Top and bottom LEDs light

: during the transition

Bottom LED onl

y lights: PST/B output

3-1-5. Auto transition

 When the [AUTO] button is pressed, the transition is executed automatically using the transition time which has

been set.

 When the [AUT

O] button is pressed while the fader lever is at an interim setting, the transition is executed in the

time remaining from the interim setting.

 The auto transition time is set using the menu.

Press the [FUNC] button to light its indicator, and press the [TIME] b

utton to display the TIME menu.

2 Turn [F1] to display the BKGD sub menu. 3 Tur

n [F4] to select the display unit using the UNIT item.

4 When frames (F) ha

ve been selected as the unit, turn [F2] or [F3] to set the transition time.

5 When seconds (SEC) hav

e been selected as the unit, turn [F2] to set the second units or [F3] to set the

frame units.

BKGD TransTime Unit 1/5 16s 39f Sec

BKGD TransTime Unit 1/5 999f Frame

 Any time from 0 to 999f can be set. The time which can be set when seconds are used as the display unit

differs depending on the video format.

59.94i: max. 33s09f, 59.94p: max. 16s39f 50i:

max. 39s24f, 50p: max. 19s49f

3-1-6. Cut transition

When the [CUT] button is pressed, the transition is executed instantly.

3. Basic operations

3-2. Wipe

3-2-1. Selecting the wipe pattern

BKGD PATT

KEY PATT

FUNC

WIPE PATTERN / FUNCTION

WIPE SQ

SL 3D

PAGE

TIME WIPE COLOR

KEY CHR KEY FREEZE

DSK PinP IN/OUT

MEMORY XPT SYSTEM

1 2 3

4 5 6

7 8 9

The wipe patterns which are allocated to the 12 wipe pattern buttons are used as the basis for wiping, and each button has four pages — wipe, squeeze, slide and 3D — of patterns. (Refer to the table of wipe patterns.) Displayed for each wipe pattern selector button are an image of the basic wipe pattern and a number.

Press the [BKGD PA

TT] button or [KEY PATT] button to select the page.

Each time the button is pressed, the page is selected, and the indicator LED (WIPE, SQ, SL or 3D) for the

selected page lights. (3D cannot be selected using the [KEY PATT] button.)

Select the button from among the 1

2 wipe pattern selector buttons for which the number of the pattern concerned is indicated. The selected pattern lights, and a wipe image appears on the external monitor (OSD).

The pattern page indicator LEDs light only when the [BKGD PATT] button or [KEY PATT] button has been selected.

WIPE SQ (squeeze) SL (slide) 3D (3 dimensions)

1 2 3 1

SQ1SL

1 2 3

4 5 6 4

pattern

4 5 6

7 8 9 7

7 8 9

10 11 12 10

pattern

10 11 12

 There are no corresponding patterns for 11 of SQ and 5, 10, 11 and 12 for SL and, therefore, they cannot be

selected.

3. Basic operations

3-2-2. Selecting the wipe direction

Operate the wipe direction selector buttons to select the wipe direction for the background transition. (The key transitions are set by the menu. The direction which is set here will not be reflected.  See 3-3-3.)

When the indicators are off:

Wiping proceeds in the normal direction.

When the [R] indicator is lighted:

Wiping proceeds in the rev

erse direction.

When the [N/R] indicator is lighted:

The normal direction is replaced with the re

verse direction (or vice versa) when the transition is completed. (The lighted and extinguished statuses of the [R] button are also switched in line with the direction of the wiping.)

!."

"2!

! "

.2

! "

3-2-3. Wipe decorations (border, soft effect)

A border effect or soft effect can be added to the wiping of background transitions (but not for key transitions).

 Setting the border and soft eff

ect

1 Press the [FUNC] button to light its indicator

, and press

the [WIPE] button to display the WIPE menu.

2 Turn [F1] to display the Border sub menu.

Turn [F2] to set ON (or OFF) for the border using the

Border item.

Turn [F3] to set the width of the border using the Width

item.

Turn [F4] to set the amount of soft effect using the Soft

item.

The soft effect is OFF if 0 is set.

Border Border Width Soft 1/5 Off 5.0 0.0

0.1

～

100.0

0.0

～

100.0

When “On” has been selected as the Border item setting, the ratio of the soft effect to the border width is

indicated as the amount of soft effect.

When only the soft effect is to be added to wipe

, select “Off” as the Border item setting.

 Setting the border color

On the WIPE menu, turn [F1] to display the BodrCol

sub men

2 Turn [F2], [F3] and [F4] to adjust the Hue, Sat and Lum

of the border color

3 To call a preset color, turn [F5] to select the preset color

using the Load item, and press the [F5] s

witch. The Hue, Sat and Lum values are changed to the preset color values. (The values which ha

ve been set will not be stored in

the memory until the [F5] switch is pressed.)

BodrCol Hue Sat Lum Load 2/5 0.0 0.0 100.0 White

0.0

～

359.9

0.0

～

100.0

0.0

～

108.0

Yellow Cyan Green Magenta Red Blue Black

3. Basic operations

3-2-4. Setting the wipe start position

Any start position can be set for wipe pattern WIPE and SQ #5. The start position has one set of values for a background pattern and another set for a key pattern.

Press the [FUNC] button to light its indicator

, and press the [WIPE] button to display the WIPE menu.

2 Turn [F1] to display the WIPEPos sub menu or the SQPos sub menu.

<Men

u display>

WIPEPos

Select X-Pos Y-Pos CopyTo

3/5 BKGD 0.00 0.00 KEY

KEY

−100.00

～

+100.00

−100.00

～

+100.00

3 Turn [F2] to select the pattern (background or key) to be set using the Select item. 4 Either operate the positioners or tur

n [F3] and [F4] to set the wipe start position using the X-Pos item and Y-

Pos item.

These settings can be established only when

WIPE or SQ #5 has been selected as the background pattern

or key pattern.

Either operate the f

ader lever or press the [AUTO] button to check the wipe operation. (When, for instance, –50 has been set for X-Pos and –50 for Y-Pos, the following screen (or key) appears from the bottom left and wipe is performed while the screen (or key) moves to the screen center.)

<X-Pos, Y-Pos setting range>

Inside screen area Outside screen area

6 To copy the start position settings, press [F5].

The copy destination appears under the CopyTo item. (It will not change even if [F5] is turned.)

3. Basic operations

3-2-5. Modifying wipe

 Setting the lighting effect

When 3D (1, 3, 7, 9) has been selected as the wipe pattern, a lighting effect can be added. 1

Press the [FUNC] button to light its indicator

, and press the [WIPE] button to display the WIPE menu.

2 Turn [F1] to display the Modify sub menu.

<Men

u display>

Modify Light Trim 5/5 Off Off

4:3

3 Turn [F2] to select whether the lighting effect is to be added using the Light item. On: The lighting effect is added. Off: The lighting effect is not added.

 Setting the trimming

When SQ, SL or 3D has been selected as the wipe pattern, the tr

imming can be set.

The trimming setting takes effect only when the HD format has been set as the system format.

On the WIPE menu, turn [F1] to display the Modify sub menu.

Turn [F5] to set the aspect ratio to which the images are to be trimmed using the Trim item.

On:

No trimming

4:3: The images are trimmed using the 4:3 aspect r

atio. Trimming is released when the transition is

completed.

3. Basic operations

3-3. Key

This operation combines the background image with another image. The key definition can be adjusted, and an edge can be added to the combined image.

Also available as materials besides KEY for combining with the background image are PinP (picture in picture) and DSK (downstream key). The figure below shows their priorities.

<Key, PinP and DSK priorities>

KEY

PinP

DSK

Background image

How key combinations work is shown in the figure below.

HS400

Background

Key source

Key fill

Output image

Invert

3. Basic operations

3-3-1. Selecting the key type

1 Press the [FUNC] button to light its indicator, and press the [KEY] button to display the KEY menu. 2 Turn [F1] to display the KEY sub menu.

Turn [F2] to select the Type item.

<Men

u display>



KEY

Type LumKey Fill PVW

1/8 Linear ChrmOff Bus Auto

Lum Chroma

ChrmOn Matte Off

Lum (luminance key/self key):

This is for creating the key signals from the luminance component or luminance and chroma component

of the key fill signal.

Linear (linear key/EXT key):

This is for creating the key signals from the luminance component of the key source signal. It is used

when the key source signal and key fill signal are different.

Chroma (chr

oma key/self key):

This is for creating the key signals using a specific hue of the key fill signal as the reference.

Since the luminance and chroma keys are operated as self keys, the key fill signals are used as the key source signals. When the luminance key or chroma key has been selected as the key type, the key signals will remain unchanged even when the key source signals are switched. Furthermore, when “Lum” or “Chroma” is selected, the KEY button in the crosspoint area changes to lighting in amber (key fill bus selection status).

When using the linear key, use material with a black background and white characters or shape to be combined by the key as the key source signal. Material which is not black and white may not be combined clearly. Material with a white background and black characters, etc. can be reversed using the key invert function for use.

When the luminance ke

y has been selected, the chroma component can be included in the generation of the

key signals in view of the self key application. (This does not apply to the linear key.)

Tur

n [F3], and select the setting using the LumKey item.

ChrmOn: In addition to the luminance component, the chroma component is also taken into account in the

gener

ation of the key signals.

This is the setting f

or using a color with a low luminance component for the key signals (such as

when defining blue characters).

ChrmOff: The k

ey signals are gener

ated from only the luminance component.

5 Turn [F4] to select the fill type using the Fill item. Bus:

The bus signal is used for the k

ey fill signal.

Matte: The internal fill matte is used for the k

ey fill signal.

3. Basic operations

3-3-2. Selecting the key material

 Selecting the key fill and key source signals

Press the KEY button in the AUX bus selection area, and switch the selection of the key fill signal (indicator lights in amber) and key source signal (indicator lights in green).

With the indicator of the KEY button lighted in amber, press one of the AUX crosspoint buttons 1 to 10 to select the key fill signal. The indicator of the selected crosspoint button lights in amber. (It will light in red if the selected signal is being output from the PGM connector.)

Lighting in amber

KEY DSK PinP AUX CLN PVW PGM

AUX SOURCEAUX BUS DELEGATION

AUX

AMB:FILL / GRN:SOURCE

With the indicator of the KEY button lighted in green, press one of the AUX crosspoint buttons 1 to 10 to select the key source signal. The indicator of the selected crosspoint button lights in green. (It will light in red if the selected signal is being output from the PGM connector.) Since the luminance and chroma keys are operated as self keys, the key fill signals are used as the key source signals. When the luminance key or chroma key has been selected as the key type, the key signals will remain unchanged even when the key source signals are switched.

Lighting in green

KEY DSK PinP AUX CLN PVW PGM

AUX SOURCEAUX BUS DELEGATION

AUX

AMB:FILL / GRN:SOURCE

 Setting the fill matte color

1 Press the [FUNC] button to light its indicator

, and press the [KEY] button to display the KEY menu.

2 Turn [F1] to display the FillMatt sub menu.

Turn [F2] ,[F3] and [F4] to adjust the Hue, Sat and Lum of the fill matte.

To call a preset color, turn [F5] to select the preset color using the Load item, and press the [F5] switch.

The Hue, Sat and Lum values are changed to the preset color values.

(The values which have been set will not be stored in the memory until the [F5] switch is pressed.)

FillMatt

Hue Sat Lum Load

3/8 0.0 0.0 100.0 White

0.0

～

359.9

0.0

～

100.0

0.0

～

108.0

Yellow Cyan Green Magenta Red Blue Black

3. Basic operations

3-3-3. Key transitions

1 Select key in the transition mode. Press the [KEY] button in the transition area to light its

indicator.

To e

xecute a background transition and key transition at the same time, press the [BKGD] button and [KEY] button together to turn on both indicators.

MIX WIPE

BKGD KEY

MIX

WIPE

2 Select the transition type. Use the [MIX] button or [WIPE] button in the transition area to

select the key transition mode. The indicator of the selected button lights in amber. At the same time, the MIX or WIPE selection status indicator LED lights. When WIPE has been selected, press the [KEY P

ATT] button

to light its indicator, and select the wipe pattern.

Set the time of the transition. On the TIME menu, turn [F1] to display the KEY sub menu.

As with a background transition, set the transition time.

BKGD PATT

KEY PATT

FUNC

WIPE PATTERN / FUNCTION

WIPE SQ

SL 3D

PAGE

TIME WIPE COLOR

KEY CHR KEY FREEZE

DSK PinP IN/OUT

MEMORY XPT SYSTEM

1 2 3

4 5 6

7 8 9

10 12

4 Set the wipe direction. On the KEY menu, turn [F1] to display the Trans sub menu. Turn [F1] to set Nor (normal) or Rev (reverse) using the

OutPatt item.

Nor (normal): The ke

y out pattern moves in the same direction as the key in pattern.

Rev (reverse): The ke

y out pattern moves in the opposite direction from the key in pattern.

However, the operations in pattern example 3 are performed for WIPE 5, 10, 11 and 12, and the operations

in pattern example 4 are performed for SQ 5, 10 and 12.

Pattern example 1 Pattern example 2 Pattern example 3

(WIPE5, 10, 11, 12)

Pattern example 4

(SQ5, 10, 12)

Key in

Key out (Nor)

Key out (Rev)

: This indicates the areas where keys are combined.

+ 68 hidden pages

Panasonic AVHS400N - MULTI FORMAT LIVE SWITCHER Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual