Arbitrator-CP ver.1.9
Quick Reference Guide
Officer Information
Register at the beginning of shift & delete at the end of shift
(A) Register the Officers information (At the beginning of shift)
(1) “Auto”: Plug USB memory (saved the officer information) to VPU.
(2) “Manual”: Plug USB memory to VPU and press “Load” button.
If 2 officers need to be loaded, plug 2 different USB memories to VPU.
(3) “List”: Press “Select” button in “Officer” by Control Panel menu.
(B) Delete the Officer information (At the end of shift)
“Manual”, “List”: Press “Delete” button in “Officer” by Control Panel menu.
[Top Menu]
-while REC stopped-
[Manual]
[List]
Register
Officers
Delete
Officers
Control Panel Menu for Officer
[Top Menu]
[Restore]
When appeared in
Control Panel OSD, execute
“Restore”
[Setup/Info]
[Camera] For users who do not use LPR (Licens e Plate Recognition mode)
(“Init LPR Mode” in Admin set up is “Dis able” as a factory default.)
*For LPR users, please go to ”Camera Menu for LPR” for details
Re-Auto Focusing
Adjust manual focus
Adjust image brightness
[Audio]
1. “IN CAR” for In car Mic (Mic in)
2. “WMIC” for 2nd Wireless Mic (Audio 2 in)
3. “LINKCAM” to change the Audio 1 or 2
by linking with the camera changes,
*Audio 1 for Wireless Mic 1 (Audio 1 in)
Check Audio
[Archive]
Playback the recorded video
On Screen Type for Control Panel
“Auto”, “SIMPLE”, “DETAILS” or “OFF”
Camera LED (Camera Tally Light),
for “ON” or “OFF”
Camera Menu for LPR (License Plate Recognition)
In order to use LPR (License Plate Recognition) mode, the Administrator needs to set up
“Init LPR Mode” as “Enable” in Admin/Camera menu.
*If setting up “Init LPR Mode” as “Disable”, there will be no “LPR Mode”, “LPR/Patrol Shutter Speed”, “LPR/Patrol Zoom” on screen as shown
below. (Just “Auto Focus”, “Manual Focus” or “AE” can be selectable and changed in “Camera” menu.)
[Top Menu] while recording is
being stopped in the live screen
[Top Menu] while the live screen
is being recorded
[Camera]
1) [LPR Mode] is set to “LPR”
LPR ON LPR OFF
[Camera]
1) [LPR Mode] is set to “LPR”
2) [LPR Mode] is set to “PATROL”
“LPR” for LPR ON
“Patrol” for LPR OFF
Select “Auto”,
“1/500”, or “1/1000”
Select “Auto”, “1/100”
“1/500”, or “1/1000”
Set x1.0 to x22.0
2) [LPR Mode] is set to “PATROL”
Control Reference Guide
Front Camera (AG-CK10P)
Rear panel LED Control
Backlight compensation
to make it brighter
Auto Zoom
Camera Control
REC LED
Lights up in RED
while recording
Connector for VPU
T(TELE) for Zoom In
W(WIDE) for Zoom Out
REC Start and STOP
*Keep pressing this button for
more than 2 seconds will stop recording.
SUN Shade
REC
LED
Control Reference Guide
P2 Recorder - VPU (AG-CPD15P)
Key Lock
Locks and unlocks
the P2 Card slot cover
P2 card
slot cover
REC
button
STOP
button
READY lamp
Lights up when
recording is ready
BUSY lamp
Lights up or flashes
while a P2 card is accessed.
P2 card
slot 1, 2
Control Reference Guide
Control Panel (AG-RCP30P)
Backlight
Compensation
T: Zoom In
W: Zoom Out
REC/STOP
Lamp
REC
Button
Book
Mark
Auto
Zoom
LCD
Screen
1) Lock Lamp
Lock except “REC”, “Menu”,
“Control Panel ON/OFF”,
“Return” Button while lights on
2) Ready Lamp
3) Busy Lamp
Cursor Button
Return
To go back to previous
menu or setting
Menu
Skip
(Back/Forward)
Live/Archive
Switching Button
STOP
Button
Audio 2 Mute
Button/Lamp
Mute Audio 2 and lamp lights
on by pushing this button.
No recording while muting
(lights on)
IR Mode
(Auto/ON/OFF)
Camera
Select
(Camera1/2))
Volume
Control
Control Panel
ON/OFF
Brightness
Control
Digital Wireless Microphone TX and RX (CCR24PNA)
Transmitter (TX)
with Receiver (RX)
Built-in Mic
Control Reference Guide
Transmitter (Top View)
TALK Button:
Press for REC
Lavalier Mic
Input
TALK ON : Green LED
BATT : Red-Charging, Green-Fully charged
Please refer to CCR24PNA User Guide for more operation information
MODE Selection Button
Transmitter (Bottom View)
MUTE Button
ON/OFF
Switch
Control Reference Guide
(CCR24PNA Vibration / LED Indication)
Mode
Selection
Vibration
and
LED
Vibration Only No Vibration
when Tx is
ready
No Vibration
GREEN On GREEN Blink RED Blink RED On
when Tx is
under
recording
mode
Vibration
(one time only)
Vibration
(one time only)
when Tx is
under
"Low Battery"
status
Vibration
(1 time per second)
Vibration
(1 time per second)
when Tx is
under
"Out Of Range"
status
Vibration
(2 times per 3 seconds)
Vibration
(2 times per 3 seconds)
when Mute is initiated
Vibration
(1 time per 5 seconds)
Tx is not recording:
GREEN On & RED Fast Blink
-------------------------------------------Tx is under recording:
GREEN Blink & RED Fast Blink
Vibration
(1 time per 5 seconds)
None
No Vibration
No LED
1. Default mode when power on.
2. After synchronized, the mode goes back to the last.
3. Please refer to CCR24PNA User Guide for more operation information
Loading...