Panasonic A406 Quick Setup Manual
GUIDE
PANASONIC A406 REPEATER
Online instructional videos and manufacturer user guides are also available.
QUICK SETUP GUIDE
Visit www.primus.ca/hpbxguide for more information.
What You Need
Panasonic base unit and cordless
handset (model KX-TGP600) from
Primus Business Services
Panasonic DECT repeater (model
KX-A406) from Primus Business
Services
Hosted PBX service from Primus
Business Services
Before you Start
Your Panasonic base unit and cordless phone must be setup, turned on, and
functioning prior to installing the repeater. Please refer to the Panasonic TGP600
TPA60 TPA65 Quick Setup Guide, available at
information.
www.primus.ca/hpbxguide
for more
Registering the Repeater to the TGP600 Base
Unit
1. Plug the AC adapter into the repeater. Press the plug firmly to make sure it
is in place. There is a hook at the bottom of the unit to secure the cable in
place to prevent it from being accidentally pulled out. Do not plug in the AC
adapter into an electrical outlet yet.
PRIMUS BUSINESS SERVICES | HOSTED PBX | PANASONIC A406 REPEATER QUICK SETUP
PRIMUSBUSINESS.CA
1
GUIDE
2. On the base unit, press and hold the Handset locator button for 4 seconds
until the STATUS indicator flashes red. If all registered handsets start
ringing, press the same button to stop and repeat the step. The next step
must be completed within 90 seconds.
3. Plug the AC adaptor of the repeater to an electrical outlet.
4. On the repeater, the STATUS indicator and indicator will turn amber
for 2 seconds. When both indicator lights turn solid green, the repeater is
registered to the base unit and is ready to use.
5. On the base unit, exit registration mode by pressing the Handset locator
button.
NOTE:
Register repeaters one by one. Do not register multiple repeaters at the
same time.
PRIMUS BUSINESS SERVICES | HOSTED PBX | PANASONIC A406 REPEATER QUICK SETUP
PRIMUSBUSINESS.CA
2
GUIDE
If the indicator lights of the repeater do not turn green, make sure the
repeater is within range of the base unit and try again.
For wall mount instructions, see Panasonic DECT Repeater Installation
Manual for the KX-A406, available at http://primus.ca/business/hpbxguide.
For additional troubleshooting tips, please review the Hosted PBX Small
Office Basic Troubleshooting Guide, available at
http://primus.ca/business/hpbxguide.
If the configuration process was interrupted or if you need assistance, please
contact Primus HPBX Technical Support at 1-888-222-8577.
PRIMUS BUSINESS SERVICES | HOSTED PBX | PANASONIC A406 REPEATER QUICK SETUP
PRIMUSBUSINESS.CA
3
GUIDE
Registering the Repeater to Another Repeater
A repeater can be connected to another repeater in series to extend total coverage
to up to 150m. This can be done by registering the repeater to another repeater.
In the diagram above, the destination repeater is registered with the base unit, and
the origin repeater is connected in series to the destination repeater. This section
describes how to set up the origin repeater. Before you begin, you must
register the destination repeater to the TGP600 base unit. Please follow the
steps in the previous section on how to register a repeater to the base unit.
To register a repeater to another repeater, they must be set to the same ID.
On the destination repeater:
(Destination
Repeater)
(Origin
Repeater)
1. First check the ID of the repeater you are attempting to register to
(destination repeater). With the destination repeater turned on and
functioning normally, press the PROGRAM button located under the
destination repeater. Note the number of times the indicator flashes
green. This is the ID of the destination repeater – one flash indicates the ID
as 1, two flashes indicate the ID as 2, and so on.
2. Return the destination repeater back to normal operation by pressing the
PROGRAM button again. Both the and STATUS indicators should go
back to solid green.
On the origin repeater:
3. Turn on the repeater you want to register (origin repeater) by connecting the
AC adaptor. The STATUS indicator should be flashing red and the
indicator should be off.
4. On the origin repeater, press and hold the PROGRAM button for 5 seconds
until the STATUS indicator flashes green. Release the PROGRAM button.
PRIMUS BUSINESS SERVICES | HOSTED PBX | PANASONIC A406 REPEATER QUICK SETUP
PRIMUSBUSINESS.CA
4
Loading...