Panasonic 1740 User Manual

Fire alarm systems

Alert annunciation

• Controller for the Alert Annunciation function

• Compact size

controller 1740

Alert annunciation controller

When the Alert Annunciation (AA) function
shall be used in system EBL500. The unit is
required for the related manoeuvres, i.e. to
acknowledge / reset the alarms.
For a detailed description of the Alert
Annunciation function, see system EBL500
Planning and Operating Instructions.
The unit shall be mounted close to the c.i.e.
(or an ext. FBP / Presentation unit) where
the fire alarms will be presented.

LEDs, push buttons etc.

The designation texts for the LEDs and push
buttons on the front are in Swedish.

The unit has the following LEDs:

• Larm, indicating fire / AA alarm.

• Drift, indicating that the unit is in

operation, i.e. the AA function is
enabled in the system. Normally a time
channel is used to enable this function.

• Räddningstjänsten larmad, indicating

that the "Fire brigade tx" output is
activated in the c.i.e. because:

- the activated fire alarm is not
alarm

- the AA function has been ended, e.g.
the acknowledge or investigation time
has run out, etc.

• Kvittering, indicating that the AA alarm

has been acknowledged.

an AA

Compact size

The compact size enclosure is made of grey
high impact ABS. Fitted with a supple­mentary "O" ring gasket, it will comply with
IP61, in respect of dust and moisture. The
unit has no door, i.e. the front is accessed
directly, when required. The push buttons
are disabled until they are supposed to be
used. The unit shall be wall mounted.

Miscellaneous

The LED "Kvittering" (Acknowledge) can
be turned on by the push button
"Kvittering" (Acknowledge) or by an
input, i.e. a programmable output in the
c.i.e. This is set via a jumper "JP1" in the
unit.
The unit is power supplied from the c.i.e.
or an external power supply.
One supplementary compression gland
can be used for cable entry when required.

Product application

1740 is intended to be used in the fire alarm
system EBL500 but can be used in the
systems EBL1000 / 2000 / 512 / 128 as well.

The 1740 controller is intended to succeed
the alert annunciation controller 2232.

The unit has the following push buttons:

• Kvittering, used to acknowledge an AA

alarm.

• Återställning, used to reset an AA

alarm.

Panasonic Electric Works Fire & Security Technology Europe AB
Citadellsvägen 23, SE-211 18 Malmö, Sweden
Tel: [phone] • Fax: [phone]
[e-mail] • www.panasonic-fire-security.com

Type number

1740 Alert annunciation controller.

Technical data

Voltage (V DC)
nominal
Current consumption at nom. volt. (mA)
quiescent
active2

Ambient temperature (°C)
operating
storage
Ambient humidity (% RH) max. 90, non condensing
Ingress Protection rating (estimated) IP61 (with the "O" ring gasket)

Inputs

1. Operation

2. Fire

3. Fire brigade alerted

4. Acknowledged
Outputs

1. Acknowledge

2. Reset
Size W x H x D (mm) 220 x 145 x 50
Weight, (g) 400
Colour (high impact ABS) Grey (RAL 7035)
Approvals CE; Conforms to EN54-2 and –4 whenever applicable. Conforms to

1

See input 1 below.

10
40

0 to +40

-40 to +70

24 V DC, (voltage input, 19-30 V DC, via a time channel)
General fire alarm (normally open contact)
Fire brigade tx activated (normally open contact)
Alert annunciation acknowledged (normally open contact)

Relay contacts for 1 A @ 24 V DC.
Push button "Kvittering" activated (normally open)

Push button "Återställning" activated (normally open)

SBF 110:6.

1

LED "Drift" turned on.

2

LED "Kvittering" or LED "Räddningstjänsten larmad" turned on.

All technical features and data are subject to changes without notice, resulting from continuous development and improvement.

Product Leaflet Date of issue Revision / Date of revision

MEW00279 2002-10-21 3 / 2006-08-31