Pacific Digital 775I65PE-M User Manual

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Disclaimer:Disclaimer:

Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published November 2004

ASRock 775i65PE-M Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

Motherboard LMotherboard L

ayoutayout

ayout

ayoutayout

English

EnglishEnglish

1 PS2_USB_PWR1 Jumper 16 Clear CMOS Jumper (CLRCMOS0) 2 A TX 12V Connector (A TX12V1) 17 Infrared Module Header (IR1) 3 775-Pin CPU Socket 18 Floppy Connector (FLOPPY1) 4 184-pin DDR DIMM Slots (DDR1- 2) 19 Game Port Connector (GAME1) 5 Secondary IDE Connector (IDE2, Black) 20 Internal Audio Connector: AUX1 (White) 6 Primary IDE Connector (IDE1, Blue) 21 Internal Audio Connector: CD1 (Black) 7 North Bridge Controller 22 JR1 / JL1 Jumpers 8 AGP Slot (1.5V_AGP1) 23 Front Panel Audio Header (AUDIO1) 9 South Bridge Controller 24 PCI Slots (PCI1- 3) 10 Secondary Serial AT A Connector (SATA2) 25 FSB Select Jumper (FSB_SEL1) 11 Primary Serial AT A Conne ctor (SA T A1) 26 BIOS FWH Chip 12 USB 2.0 Header (USB67, Blue) 27 Shared USB 2.0 Header (USB4_5, Blue) 13 Chassis Fan Connector (CHA_FAN1) 28 CPU Fan Connector (CPU_FAN1) 14 System Panel Header (PANEL1) 29 ATX Power Connector (A TXPW R1) 15 Chassis Speaker Header (SPEAKER 1)

ASRock 775i65PE-M Motherboard

TMTM

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

ASRock I/O PlusASRock I/O Plus

1 Parallel Port 7 USB 2.0 Ports (USB01) 2 RJ-45 Port 8 USB 2.0 Ports (USB23) 3 Line In (Light Blue) 9 Serial Port: COM1 4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple) 5 Microphone (Pink) 11 PS/2 Mouse Port (Green) 6 Shared USB 2.0 Ports (USB45)

TMTM

ASRock 775i65PE-M Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

1. Introduction1. Introduction

Thank you for purchasing ASRock 775i65PE-M motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-bystep installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest memory and CPU support lists on ASRock website as well.

ASRock website

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

1.1 Package Contents1.1 Package Contents

ASRock 775i65PE-M Motherboard

(Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm) ASRock 775i65PE-M Quick Installation Guide ASRock 775i65PE-M Support CD

(including LGA 775 CPU Installation Live Demo) One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive One Serial ATA (SATA) Data Cable One Serial ATA (SATA) HDD Power Cable (Optional) One ASRock I/O PlusTM Shield

http://www.asrock.com

English

EnglishEnglish

ASRock 775i65PE-M Motherboard

1.2 Specifications1.2 Specifications

1.2 Specifications

1.2 Specifications1.2 Specifications

Platform: Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm CPU: 775-Pin Socket

Supporting Intel® Pentium® 4 / Celeron® processor (in 775-land LGA package)

Chipsets: North Bridge:

Intel® 865PE chipset, FSB @ 800 / 533MHz, supports Hyper-Threading Technology (see CAUTION 1)

South Bridge:

Intel® ICH5, supports SATA 1.5Gb/s

Memory: 2 DDR DIMM slots: DDR1 and DDR2

supports PC3200 (DDR400) / PC2700 (DDR333) / PC2100 (DDR266), Max. 2GB (see CAUTION 2)

Dual Channel Memory Technology support (see CAUTION 3)

IDE: IDE1: ATA 100 / Ultra DMA Mode 5

IDE2: ATA 100 / Ultra DMA Mode 5 Supports up to 4 IDE devices

Serial ATA: Supports up to 2 SATA devices at 1.5Gb/s data transfer rate

(Not Support “RAID and “Hot Plug” functions)

Floppy Port: Supports up to 2 floppy disk drives Audio: 5.1 channels AC’97 Audio PCI LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN Hardware Monitor: CPU temperature sensing,

Chassis temperature sensing, CPU overheat shutdown to protect CPU life (ASRock U-COP)(see CAUTION 4), CPU fan tachometer, Chassis fan tachometer, Voltage monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 3 PCI slots with PCI Specification 2.3 AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 5) USB 2.0: 8 USB 2.0 ports:

includes 6 default USB 2.0 ports on the rear panel, plus two headers to support 2 additional USB 2.0 ports (see CAUTION 6)

ASRock I/O PlusTM: 1 PS/2 mouse port,

1 PS/2 keyboard port, 1 serial port: COM1, 1 parallel port: ECP/EPP support, 6 default USB 2.0 ports, 1 RJ 45 port,

EnglishEnglish

English

ASRock 775i65PE-M Motherboard

English

EnglishEnglish

Audio Jack: Line In / Line Out / Microphone

BIOS: AMI legal BIOS,

Supports “Plug and Play”, ACPI 1.1 compliance wake up events, Supports jumperfree, CPU frequency stepless control (only for advanced users’ reference, see CAUTION 7)

OS: Microsoft® Windows® 98 SE / ME / 2000 / XP compliant

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 24 in the support CD.

2. Please check the table below for the memory support frequency and its corresponding CPU FSB frequency.

CPU FSB Frequency Memory Support Frequency

800 DDR266, DDR320

533 DDR266, DDR333

* When you use an FSB800-CPU on this motherboard, it will run at

DDR320 if you adopt a DDR333 memory module.

3. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 10 for proper installation.

4. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU a nd the he atsink when you install the PC syste m.

5. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage!

6. Power Management for USB 2.0 works fine under Microsoft SP1 / 2000 SP4. It may not work properly under Microsoft® Windows® 98/ ME.

7. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the

CPU.

*, DDR400

Windows® XP

ASRock 775i65PE-M Motherboard

2.2.

InstallationInstallation

Installation

2.2.

InstallationInstallation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Pre-installation PrecautionsPre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

2.12.1

CPU InstallationCPU Installation

2.1

CPU Installation

2.12.1

CPU InstallationCPU Installation

For the installation of Intel 775-LAND CPU, please follow the steps below.

775-Pin Socket Overview

Before you insert the 775-LAND CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

ASRock 775i65PE-M Motherboard

EnglishEnglish

English

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two orientation key notches.

Pin1

orientation

key notch

orientation

key notch

Pin1

alignment key

black line

alignment key

English

EnglishEnglish

775-Pin Socket

775-LAND CPU

For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick a nd Pla ce Cap):

Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.

ASRock 775i65PE-M Motherboard

It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

2.2

Installation of CPU Fan and Heatsink

2.22.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU. Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_FAN1, see page 2, No. 28).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or contact other components.

ASRock 775i65PE-M Motherboard

EnglishEnglish

English

2.32.3

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

2.3

Installation of Memory Modules (DIMM)

2.32.3

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

775i65PE-M motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots.

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

English

EnglishEnglish

1010

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

ASRock 775i65PE-M Motherboard

2.4 Expansion Slots (PCI and AGP Slots)2.4 Expansion Slots (PCI and AGP Slots)

2.4 Expansion Slots (PCI and AGP Slots)

2.4 Expansion Slots (PCI and AGP Slots)2.4 Expansion Slots (PCI and AGP Slots)

There are 3 PCI slots and 1 AGP slot on 775i65PE-M motherboard. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot ha s

a special design of clasp that can securely fasten the inserted graphics card.

Please do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage! For the voltage information of your AGP card, please check with the AGP card vendors.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Installing an expansion cardInstalling an expansion card

STEP 1: Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.

STEP 2: Remove the system unit cover (if your motherboard is already installed in

a chasis).

STEP 3: Remove the bracket fa cing the slot that you intend to use. Keep the screws

for later use.

STEP 4: Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

STEP 5: Fasten the card to the chassis with screws. STEP 6: Replace the system cover.

ASRock 775i65PE-M Motherboard

1111

EnglishEnglish

English

2.5 Jumpers Setup2.5 Jumpers Setup

2.5 Jumpers Setup

2.5 Jumpers Setup2.5 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “SHORT”. If no jumper ca p is placed on the pins, the jumper is “OPEN”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “SHORT” when jumper cap is placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1(see p.2 No. 22) JL1(see p.2 No. 22)

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS0, 2-pin jumper) (see p.2 No. 16)

2-pin jumper

Short Open

or USB wake up events.

English

EnglishEnglish

1212

Note: CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS0 for 3 seconds. Please remember to remove the jumper cap after clearing the CMOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action.

ASRock 775i65PE-M Motherboard

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

FDD connector

(33-pin FLOPPY1) (see p.2 No. 18)

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue) Secondary IDE connector (Black)

(39-pin IDE1, see p.2 No. 6) (39-pin IDE2, see p.2 No. 5)

connect the blue end

to the motherboard

connect the black end to the IDE devices

80-Conductor ATA 66/100 cable

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SAT A1: see p.2 No. 1 1) connectors support SATA data (SAT A2: see p.2 No. 10) cables for internal storage

SAT A2

SAT A1

devices. The current SATA interface allows up to 1.5 Gb/s data transfer rate.

Serial A TA (SATA) Either end of the SATA data ca ble Data Cable can be connected to the SATA

hard disk or the SA TA conne ctor on the motherboard.

ASRock 775i65PE-M Motherboard

1313

EnglishEnglish

English

Serial ATA (SATA) Please connect the black end of Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect to the SAT A

HDD power connector

connect to the power supply

connect the white end of SATA power cable to the power connector of the power supply.

USB 2.0 Header ASRock I/O PlusTM accommo-

(9-pin USB67) dates 6 default USB 2.0 ports. If (see p.2 No. 12) those USB 2.0 ports on the I/O

panel are not sufficient, this USB 2.0 header is available to support 2 additional USB 2.0 ports.

Shared USB 2.0 Header This USB45 connector is shared

(9-pin USB4_5) with the USB 2.0 ports 4,5 on (see p.2 No. 27) ASRock I/O Plus

. When using the front panel USB ports by attaching the front panel USB cable to this connector (USB4_5), the USB ports 4,5 on ASRock I/O PlusTM will not be able to function.

English

EnglishEnglish

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting (see p.2 No. 17) and receiving infrared module.

nternal Audio Connectors These connectors allow you

(4-pin CD1, 4-pin AUX1) to receive stereo audio input (CD1: see p.2 No. 21) from sound sources such as (AUX1: see p.2 No. 20) a CD-ROM, D VD-ROM, TV

AUX1

CD1

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(9-pin AUDIO1) panel audio cable that allows (see p.2 No. 23) convenient connection and

control of audio devices.

1414

ASRock 775i65PE-M Motherboard

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel (see p.2 No. 14) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header. (see p.2 No. 15)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and (see p.2 No. 13) match the black wire to the

ground pin.

CPU Fan Connector Please connect a CPU fan cable

(4-pin CPU_FAN1) to this connector and match (see p.2 No. 28) the black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPW R1) supply to this connector. (see p.2 No. 29)

Game Port Conne ctor Connect a Game cable to this

(15-pin GAME1) connector if the Game port (see p.2 No. 19) bracket is installed.

ATX 12V Connector Please note that it is necessary

(4-pin A TX12V1) to connect a power supply with (see p.2, No. 2) ATX 12V plug to this connector

so that it can provides sufficient power. Failing to do so will cause the failure to power up.

ASRock 775i65PE-M Motherboard

1515

EnglishEnglish

English

2.72.7

Serial ASerial A

2.7

Serial A

2.72.7

Serial ASerial A

This motherboard adopts Intel ICH5 south bridge chipset that supports Serial ATA (SATA) hard disks. You may install SATA hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis. STEP 2: Connect the SATA power cable to the SATA hard disk. STEP 3: Connect one end of the SATA data cable to the motherboard’s primary

SATA connector (SATA1).

STEP 4: Connect the other end of the SATA data cable to the primary SATA hard

disk. If you just want to install only one SATA HDD, the installation process is complete at this step. If you want to install two SATA HDDs,

please continue to do the following steps. STEP 5: Connect the SATA power cable to the SATA hard disk. STEP 6: Connect one end of the second SATA data cable to the motherboard’s

secondary SATA connector (SATA2). STEP 7: Connect the other end of the SATA data cable to the secondary SATA hard

disk.

A (SAA (SA

Before you install OS into the SATA hard disk, you need to check and ensure the configuration of the OnBoard IDE Operate Mode option in BIOS setup is correct according to the condition of your system. For the configuration details, please refer to the instruction on page 27 of “User Manual” in the Support CD.

A) Hard Disks InstallationA) Hard Disks Installation

A (SA

A) Hard Disks Installation

A (SAA (SA

A) Hard Disks InstallationA) Hard Disks Installation

English

EnglishEnglish

1616

ASRock 775i65PE-M Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

3. BIOS Information3. BIOS Information

The BIOS Setup Utility is stored in the BIOS FWH chip. When you start up the computer, please press <F2> during the Power-On-Self-Test (POST) to enter the BIOS Setup Utility; otherwise, POST continues with its test routines. If you wish to enter the BIOS Setup Utility after POST, please resume the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. For the detailed information about the BIOS Setup Utility, please refer to the User Manual (PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

4. Software Suppor4. Software Suppor

This motherboard supports various Microsoft® Windows® operating systems: 98 SE/ ME / 2000 / XP. The Support CD that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the file “ASSETUP.EXE” from the “BIN” folder in the Support CD to display the menus.

“LGA 775 CPU Installation Live Demo”

This motherboard is equipped with Intel LGA 775 socket, which is a new CPU socket interface that Intel has released. Since it has several tiny pins, whcih are easily to be damaged by improper handling, ASRock sincerely presents you a clear installation guide through this “LGA 775 CPU Installation Live Demo”. We hope you may check this live demo program before you start the installation of LGA 775 CPU in order to reduce the risks of CPU and motherboard damages caused by any improper handling. To see this Live Demo, you can run Microsoft® Media Player® to play the file. You may find this Live Demo in the motherboard’s Support CD through the following path:

..\ MPEGAV \ LGA775INST.DAT

t CD informationt CD information

t CD information

t CD informationt CD information

ASRock 775i65PE-M Motherboard

1717

EnglishEnglish

English