Paasche VSR-PL User Manual

INSTRUCTIONS & PARTS LIST VSR90#1-8/31/2011

Supersedes Instructions & Parts List VSR90#1-5/3/2011

WARNING: Spray materials may be harmful if inhaled or allowed
to come into contact with the skin or eyes. Consult the product

VSR90#1

Gravity Feed - Internal Mix­Double Action Airbrush

INTRODUCTlON:

Prime Characteristics of the Paasche® VSR90#1 Airbrush include the ability to spray fluids requiring gravity feed as well as make quick color
changes with the two (2) different size color cups supplied with each set. This unique two in one design allows the user choice of cup size while
using only one shell. These color cups enable the user to swivel each cup right, left or in alignment with the shell to allow an unobstructed view
of their efforts. The Double Action, Internal mix feature permits flexibility in regulation of color and air without work stoppage. The two different
size Multipleheads, Tips and Needles are quickly interchangeable to allow greater diversity in materials and coverage.

Head Sizes - Patterns - Fluid Thickness

Size 1 - Tip size .010 inches or .25mm

- Used for fine detail. Pencil Line to 1'' patterns

- Paint must be thinned further than 2 head

Size 2 -Tip size .026 inches or .66mm

- Less detail than the size 1 head. 1/32'' to 1-1/2'' patterns

- Can spray slightly thicker paint than size 1 head

Working Pressures:

• Operating pressures 20-55 PSI; Maximum pressure 75 PSI

• 20-30 PSI is best for detail spraying w/ properly thinned paint

• Use the higher pressures for thicker material where fine detail is not critical or thin the paint to allow lower pressures.

Equipment Set-up:

The Airbrush is held in the same manner as a pen, with the index finger comfortably over the Trigger.

1. Attach airhose to air supply and to airbrush. If regulator set pressure between 20 -30 PSI.

2. For VSR90#1 attach one of the color cups to color socket.

3. Remove Head Protecting Cap #1, page 2.

Airbrush Operation:

1. Press down on Trigger to release air and pull back on Trigger to control quantity of color.

2. To spray a fine line without heavy ends, start moving the airbrush without release of color. Then start the color at the beginning of line
and stop the color at the end, but continue the motion of the airbrush after the color has stopped.

3. Practice this movement until you can spray a fine line or a broad pattern without heavy build up at the beginning or end of your strokes.

4. Speed of movement controls density of color and fading effects at beginning and end of strokes.

5. For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on the Trigger to release a small
amount of paint.

6. For background work and broad effects, hold the airbrush away from the work surface and pull back on Trigger to release required
amount of color.

7. For Stippling remove the aircap, push down on the Trigger and pump the Trigger forward and back. Adjust the air pressure between
15 and 50 PSI for desired stipple effect.

8. For more instruction see the “22 Airbrush Lessons for Beginners” booklet enclosed with your airbrush.

label and Material Safety Data Sheet supplied for the spray
material. Follow all safety precautions. CAUTION: Well Ventilated
Area Required to remove fumes, dust or overspray. Secure airhose
to Airbrush with V-62 Wrench for safety and to prevent air leaks.

M a x i m u m A i r P r e s s u r e 7 5 P . S . I .

PTFE Packings.

Paasche Airbrush Company

4311 North Normandy Avenue
Chicago, IL 60634-1395

Phone: [phone] • Fax: [phone]
Website: paascheairbrush.com
E-Mail: [e-mail]

Printed in the U.S.A.

Paasche® VSR90#1 Gravity Feed, Double Action Airbrush Page 2

(A)

(B)

NO. PART DESCRIPTION

1. V-189 Head Protecting Cap

4. VB Aircap Body

VM-1 or 2 Multiplehead (Select Size)

3. VA-1 or 2 Aircap (Select Size)

31 or 32. VN-1 or 2 Needle (Select Size)

5. VT-1 or 2 Tip (Select Size)

6. V-210 Shell Assembly W/V-20

7. V-218 PTFE Packing & Packing Nut

(sold as set)

9. VSR-1 Color Cup 1/8 oz. (3.5cc)

10. VSR-2 Color Cup 3/16 oz. (5.25cc)

12. V-217 Trigger

A. V-186 Needle Valve Assembly L/Needle

17. V-191A Rocker Assembly

21. V-140 Spring

NO. PART DESCRIPTION

24. AFV-143 Chrome Plated Metal Handle

24a. TAL-34 Handle & Stop Assembly (Optional) -

allows for preset paint flow

25. V-221 Air Valve Assembly

26. V-20 Valve Casing

27. A-53 Valve ‘O’ Ring (Pack of 6)

28. V-214 Valve Plunger (with A-53)

29. A-22 Valve Spring

30. A-23R Air Valve Nut

31. VN-1 Needle (Select Size)

32. VN-2 Needle (Select Size)

33. V-54 Reamer (Optional)

22. V-136A Needle Adjusting Sleeve

23. V-141 Locknut