Ozito PXBPS-254 Instruction Manual
BUFFER
WHAT’S IN THE BOX
Buffer Polisher
POLISHER
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
No Load Speed: 2,500/min
Pad Diameter: 254mm (10”)
Weight: 1.8kg
ozito.com.au
WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
Application Bonnet
(Towelling)
Polishing Bonnet
(Fleece)
Battery & Charger
sold separately
PXBPS-254
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
OZITO
Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts, for example; polishing bonnets.
0717
KNOW YOUR PRODUCT
CORDLESS BUFFER POLISHER
1 On/Off Switch
2 Foam Pad
1 2 3 4
3 Battery Seating
4 Side Handles
SETUP & PREPARATION
1. FITTING THE BONNET
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
Choosing the Correct Bonnet to Use
2 bonnets are included with this tool and each has it’s own purpose.
ACCESSORIES
5 Application Bonnet (Towelling) 6 Polishing Bonnet (Fleece)
5 6
The application bonnet (towelling
material) should be used to apply
polishing compound to the surface.
Attaching the Bonnet
1 Pull the bonnet over one side of
the foam pad.
2 Pull the remaining
bonnet over the foam
pad.
The polishing bonnet (eece
material) is used once the polishing
compound is applied and will remove
the compound leaving a polished
surface.
BATTERY & CHARGER (sold separately)
This tool is compatible with all batteries and chargers from the Ozito
Power X Change Range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
Removing the Bonnet
1 Pull one side of the
bonnet off the foam pad
and then remove.
2. BATTERY & CHARGING (sold separately)
CAUTION: THE CHARGER FOR THIS PRODUCT SHOULD
BE PROTECTED BY A RESIDUAL CURRENT DEVICE
(RATED AT 30mA OR LESS).
The purchased battery will be shipped in a low charge condition, and requires charging
prior to use. Allow several cycles of charging and discharging (through use of the tool)
for the battery to reach its optimum performance / runtime.
Charging your lithium ion battery - Fast Charger
1 Connect the charger into a mains power outlet.
2 The charger LED will ash green
showing power is being supplied
to the charger.
3 With the charger sitting on a at
surface, align the raised ribs on
the battery with the recess in the
charger and slide onto the charger
ensuring a rm connection.
4 The charger LED will illuminate
red signifying that the battery is
charging.
5 The charger LED will illuminate
green once the battery is fully
charged.
Charging your lithium ion battery - Eco Charger
1 Connect the charger into a mains power outlet.
2 The charger LED will ash green
showing power is being supplied
to the charger.
3 With the battery sitting on a at
surface, align the raised ribs on the
battery with the recess in the charger
and slide onto the battery ensuring a
rm connection.
4 The charger LED will illuminate red signifying that the battery is charging.
5 When removing the charger from the
battery, rst press the battery release
tab, then slide the charger from its
position.
Charger LED Indicator
LED Indicator Situation
GREEN (Flashing) Stand By (no battery pack is inserted)
RED (Illuminated) Battery is charging (low charge)
GREEN (Illuminated) Battery is fully charged
RED (Flashing) Battery or Charger fault
RED & GREEN (Flashing) Battery pack is too hot or too cold (remove battery from
charger and store at room temperature 20ºC. Insert
battery again when at correct charging temperature). If
this happens again, the battery is defective and needs
to be replaced.
Charger LED Indicator
LED Indicator Situation
GREEN (Flashing) Stand By (no battery pack is inserted)
RED (Flashing) Battery is charging (low charge)
RED (Illuminated) Battery is charging (mid charge)
GREEN (Illuminated) Battery is fully charged
BOTH(Illuminated) Battery pack is too hot or too cold (charging will begin
automatically when battery reaches correct charging
temperature).
BOTH (Flashing) Defective battery. Never charge a defective battery
pack!
Remove battery pack from charger.
Battery Charge Indicator
The purchased battery is equipped with a
battery charge indicator to show the state of
the battery charge.
Press the charge indicator button and look to
see which LED lights.
Battery requires
immediate charging
Low state of charge, requires charging soon.
Mid state of charge
Full state of charge.
Note: The battery needs to be removed from the tool to check the state of charge.
Loading...