Ozito PXBP-400U Original Instructions Manual

2

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR
YOUR BATTERY CHARGER.

1. Before using the charger read all instructions and cautionary markings on the charger,
battery pack and the product using the battery pack.

2. This charger is not intended for any uses other than charging rechargeable batteries.
Any other use may result in risk of re, electric shock or electrocution.

3. Do not place any object on top of the charger or place the charger on a soft surface
that may result in excessive internal heat. Place the charger in a position away from
any heat source.

4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than
the cord when disconnecting the charger.

5. Make sure the cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.

6. An extension cord should not be used unless absolutely necessary. Use of an improper
extension cord could result in the risk of re, electric shock or electrocution.

7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise
damaged in any way. Have it checked by an electrician or power tool repairer.

8. Do not disassemble charger. Take it to an electrician or power tool repairer when
service or repair is required. Incorrect reassembly may result in a risk of electric
shock, electrocution or re.

9. To reduce risk of electric shock, unplug the charger from the outlet before attempting
any cleaning. Removing the battery pack will not reduce this risk.

10. Never attempt to connect 2 chargers together.

11. DO NOT store or use the tool and battery pack in locations where the temperature may
reach or exceed 40ºC (such as inside sheds or metal buildings in summer).

12. The charger is designed to operate on standard household electrical power (240
volts). Do not attempt to use it on any other voltage!

13. The battery pack is not fully charged out of the carton. First read the safety instruc­tions and then follow the charging notes and procedures.

14. The longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 18 - 24ºC. Do not charge the battery pack in an
air temperature below 10ºC or above 40ºC. This is important and will prevent damage
to the battery pack.

15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn
out. The battery can explode in a re.

16. Never attempt to open the battery pack for any reason. If the plastic housing of the battery
pack breaks or cracks, immediately discontinue use and do not recharge.

17. During charging, the battery must be placed in a well ventilated area.

BATTERY SAFETY WARNINGS

ELECTRICAL SAFETY

WARNING! When using mains-powered tools, basic safety precautions,

including the following, should always be followed to reduce risk of re, electric

shock, personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an
emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for the UK.

This tools charger is double insulated, therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualied persons in order to avoid hazard.

Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting
from a possible electrical insulation failure within the tool.

Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before

use, inspect the extension lead for signs of damage, wear and ageing. Replace the
extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an
extension lead not suitable for the power input of the tool or which is damaged or defective
may result in a risk of re and electric shock.

To reduce the risk of electric shock, we recommend the use of a residual current device
(rated 30mA or less).

This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.

Children should be supervised to ensure that they do not play with the appliance.

SPECIFICATIONS

Input: 18V
Battery Power: 4.0Ah Li-ion
Charge Times: 80min Fast Charger
5Hr Eco Charger
Weight: 0.65kg

1. Battery

2. Battery Release Button

3. Charge Indicator Button

ozito-diy.co.uk

DESCRIPTION OF SYMBOLS

Warning

Do not use or store battery in
temperatures exceeding 50ºC

Volts Hertz

Alternating Current

Direct Current

Milliamperes

Watts

Amp Hour

Ah

W

HzV

ac/~

mA

Lithium Ion Battery

Do not put in the rubbish

Do not get battery wet

Recycle Battery

Do not incinerate

dc

31

4.0Ah BATTERY

ORIGINAL INSTRUCTIONS

PXBP-400U

BATTERY CHARGE INDICATOR

The purchased battery is equipped with a
battery charge indicator to show the state of
the battery charge.

Press the charge indicator button and look to
see which LED lights.

Battery requires immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note: The battery needs to be removed from the tool to check the state of charge.

BATTERY PROTECTION SYSTEM

The tool is equipped with a battery protection system, which helps to ensure longevity
of the battery.

The output power automatically cuts off during operation when the tool and/or battery
are placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of overload, then pull

the switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the tool.

Note: The indicated capacity may be lower than the actual level during use or

immediately after using the tool.

1. OPERATION

CHARGING YOUR LITHIUM ION BATTERY

This battery has been shipped in a low charge condition, and requires charging prior to
use. Allow several cycles of charging and discharging (through use with a compatible
tool) for the battery to reach its optimum performance / runtime.

This battery has two compatible Ozito chargers available through your local Bunnings
Warehouse:

• PXCG-030U Fast Charger

• PXCG-120U Eco Charger

Only use the battery pack with Ozito Power X Change 18V cordless products.

1. Insert the power plug of the charger into the mains socket outlet. The green LED
will begin to ash when properly connected to power supply.

2. Insert the battery pack into the battery charger .

3. Remove battery from the charger once charged. Disconnect the charger from the
power supply.

Note: The battery pack can become a little warm during the charging. This is normal

If the battery pack fails to charge, check:
if there is voltage at the socket outlet
that the battery and charger are properly connected.

If the battery pack still fails to charge, please contact our customer service center.

ONLINE MANUAL

Scan this QR Code with your
mobile device to take you to the
online manual.

PXBP-400U

WARRANTY

All of our products undergo strict quality checks to ensure that they reach you in perfect
condition. In the unlikely event that your device develops a fault, please contact our
service department at the address shown on this guarantee card. You can also contact
us by telephone using the customer service number shown. Please note the following
terms under which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer
mentioned below promises to buyers of its new products in addition to their statutory
guarantee claims are not affected by this guarantee. Our guarantee is free of charge to
you.

2. The warranty services only covers defects due to material or manufacturing faults on
a product which you have bought from the manufacturer mentioned below are limited to
either the rectication of said defects on the product or the replacement of the product,
whichever we prefer.
Please note that our devices are not designed for use in commercial, trade or
professional applications. A guarantee contract will not be created if the device has
been used by commercial, trade or industrial business or has been exposed to similar
stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due
to incorrect installation, a failure to follow the operating instructions (for example
connecting it to an incorrect mains voltage or current type) or a failure to follow
the maintenance and safety instructions or by exposing the device to abnormal
environmental conditions or by lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the
device or the use or unapproved tools or accessories), ingress of foreign bodies into the
device (such as sand, stones or dust, transport damage), the use of force or damage
caused by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear
or by normal use of the device.

4. Your Product is guaranteed for a period of 12 months from the original date
of purchase and is intended for DIY (Do It Yourself) use only. Warranty excludes
consumable parts. Guarantee claims should be submitted before the end of the
guarantee period within two weeks of the defect being noticed. No guarantee claims
will be accepted after the end of the guarantee period. The original guarantee period
remains applicable to the device even if repairs are carried out or parts are replaced.
In such cases, the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work performed or
parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT
TO THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables
and missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE
HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk

OZITO UK Unit 9 Stadium Court, Wirral International Business Park,

Plantation Road, Bromborough, Wirral, CH62 3QG