Ozito PWE-1300 Instruction Manual
HIGH PRESSURE
CLEANER
1300W 1450 PSI
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 220–240V ~ 50Hz
Motor: 1300W
Rated Flow: 5.7 l/min
Max. Flow: 6.8 l/min
Permissible Pressure: 10 MPa (1450 psi)
Rated Pressure: 7 MPa (1015 psi)
Inlet Water Pressure: 0.6 MPa (87 psi) max.
Water Supply Temp.: 40ºC max.
IP Rating: IPX5
Weight: 4.3kg
PWE-1300
WHAT’S IN THE BOX
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: bearings,
o-rings.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1215
High Pressure Cleaner
3m High Pressure Hose
Gun & Lance
Deck & Patio Cleaner
Adjustable Spray Nozzle,
Detergent Spray Bottle
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. Accessory holder
2. Water inlet connector
3. High pressure hose connector
4. Quick connect system
5. On/Off switch
6. Carry handle
HIGH PRESSURE CLEANER
KNOW YOUR PRODUCT
1. ASSEMBLY
Fitting the accessory holder
1. Push accessory holder onto the high
pressure cleaner.
The holder can be used for storage of
the gun, lance and high pressure hose.
Deck & patio cleaner
1. Attach the extension onto the deck & patio
cleaner.
2. Fasten from the underside using the 2
screws provided
3. Attach the rotor arm to the deck & patio
cleaner and secure by inserting the U-clip.
SETUP & PREPARATION
ACCESSORIES
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING PROCEDURES.
7. Deck & patio cleaner
8. Rotor arm
9. Lance
10. Gun
11. High pressure hose
12. Screws & U-clip
13. Adjustable spray nozzle
14. Detergent spray bottle
10
Water supply
For use only with mains pressure water when a backow preventer is
installed on the inlet of the pressure washer. For further information
contact Ozito Customer Service.
1. Run water through
your garden hose
to remove any
foreign matter before
attaching to the pump
2. Attach garden hose
(min.Ø 1/2”) to the
water inlet connector
on the pump. Always
use a reinforced
hose with a standard
coupling for water
inlet. The hose should
be at least 6m in
length for proper
operation.
Note: A lter is tted to the inlet connector preventing any debris
from entering the pump. Inspect and clean the lter before use as
insufcient water supply could damage the pump.
2. CONNECTIONS
Gun and lance
1. Fasten the
lance to
the gun by
pushing and
twisting.
Quick connect system
The connections of the accessories are attached with a quick
connection system.
1. To Connect, push the
accessory onto the lance
connection.
High pressure hose
1. Connect the high pressure hose to
the gun.
2. Connect the opposite end of the high
pressure hose to the high pressure
cleaner
2. To remove, actuate the
quick connection system
and remove the accessory
Loading...