Ozito PSCW-400RB Instruction Manual

INSTRUCTION MANUAL

PSCW-400RB

STANDARD EQUIPMENT

IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:

Australia 1800 069 486
New Zealand 0508 069 486

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.

OZITO

Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer service
helpline above.

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)

use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: O-rings, bearings, seals and gaskets

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other
than that specified on the tool.

• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the
instruction manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

CLEAN WATER
SUBMERSIBLE
WATER PUMP

400W

SPECIFICATIONS

Motor: 400W
Max. Flow Rate: 4,200l/h
Max. Head: 11m
Max. Immersion: 5m
Min. Suction Depth: 50mm
Max Particle Size: Ø0.5mm
Water Temp.: 1°C - 35°C
Weight: 4.2kg

ozito.com.au

Outlet Pipes x 3

Submersible Pump

0318

ONLINE MANUAL

Scan this QR Code with your
mobile device to take you to
the online manual.

KNOW YOUR PRODUCT SETUP & PREPARATION

1. Tap Adaptor

2. Hook

3. Outlet Pipe (middle section)

4. Float Switch

5. Cord Restraint

6. Carry Handle

7. Pump Housing

8. Suction Base

9. Outlet Pipe (elbow)

10. Outlet Pipe (lower section)

11. Float Switch Adjustor

SUBMERSIBLE PUMP

1

2

3

4

7

5

8

6

9

1. ASSEMBLY

Fitting the Outlet Pipes

WARNING!: ENSURE THE TOOL IS SWITCHED OFF AND

DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING ASSEMBLY.

NOTE: Ensure the rubber seals

are tted in the outlet pipes

connectors otherwise this could
result in leaks.

1. Screw the outlet pipe lower
section onto the pump housing
by rotating in a clockwise
direction.

2. Screw the outlet pipe middle
section onto the outlet pipe
lower section by rotating in a
clockwise direction.

3. Screw the outlet pipe elbow onto
the outlet pipe middle section by
rotating in a clockwise direction.

NOTE: Make sure all pipe sections

connectors are rmly tightened so

that the rubber seal is compressed
in the connectors. This ensures no
water or air leakage will occur.

Tap Adaptor

Alternatively the outlet on pump

housing can be tted with the tap

adaptor (supplied). Simply unscrew
the tap adaptor from the outlet pipe
elbow and connect to the pump
housing.

10

11