Ozito PLS-1214 Instruction Manual

PLUNGE
SAW KIT

1200W

INSTRUCTION MANUAL

SPECIFICATIONS

Motor: 1200W
Input: 230-240V ~ 50Hz
No Load Speed: 5,200/min
Blade Diameter: 165mm (6½”)
Blade Bore: 20mm
Depth of Cut: 55mm @ 90°
42mm @ 45°

Guide Rail Length: 700mm

Weight: 4.65kg

PLS-1214

WHAT’S IN THE BOX

Plunge Saw

Clamps x 2

Guide Rails x 2

IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:

Australia 1800 069 486
New Zealand 0508 069 486

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.

OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.

Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.

ozito.com.au

0117

Hex Keys (3 & 5mm) &
Joiner

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will

be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: O-rings, bearing,
seals gaskets.

WARNING

The following actions will result in the warranty being void.

• Ifthetoolhasbeenoperatedonasupplyvoltageother
than that specified on the tool.

• Ifthetoolshowssignsofdamageordefectscaused
by or resulting from abuse, accidents or alterations.

• Failuretoperformmaintenanceassetoutwithinthe

instruction manual.

• Ifthetoolisdisassembledortamperedwithinanyway.

• Professional,industrialorhighfrequencyuse.

ONLINE MANUAL

Scan this QR Code with your
mobile device to take you to
the online manual.

KNOW YOUR PRODUCT SETUP & PREPARATION

1. DEPTH & BEVEL ADJUSTMENT

1. Hex Key Holder

2. Dust Port

3. Safety Switch

4. On/Off Trigger

5. Blade Change Lever

6. Front Handle

7. Rear Bevel Locking Knob

8. Saw Blade

9. Front Bevel Locking Knob

10. Cutting Line Guide

PLUNGE SAW

1 2 3 4 5 6

7 8 9 10

11 12 13 15 16 1714

WARNING! ENSURE THE TOOL IS SWITCHED OFF AND

DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.

Cutting Depth Adjustment

Bevel Adjustment

¥ Cutting depth A shows the cutting depth WITHOUT Guide

rail tted.

¥ Cutting depth B shows the cutting depth WITH guide rail

tted.

1. Loosen the Cutting Depth
Knob.

1. Loosen both Bevel Locking
Knobs.

3. Tighten Bevel Locking
Knobs.

2. Press the Knob inwards and slide to set the desired depth
using the Cutting Depth Scale.

2. Align Base Plate to desired
angle on Bevel Angle Scale.

Depth should be adjusted so that no more than one tooth
is protruding through the timber. This helps to minimise
splintering.

11. Cutting Depth Scale

12. Bevel Angle Scale

13. Cutting Depth Knob

14. Base Plate

15. Blade Locking Lever

16. Guide Rail Adjusting Knob

17. Rear Handle

3. Tighten Cutting Depth Knob.

B
A