Ovislink Air Live WIAS-3200N v2 User Manual

WIAS

-

3200N v2

802.11n Interne

t Access

Server

User

’

s Manual

Table of Contents

i AirLive WIAS-3200N v2 User’s Manual

Copyright & Disclaimer

No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.

OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice

All Trademarks are properties of their respective holders.

Table of Contents

AirLive WIAS-3200N v2 User’s Manual

ii

FCC Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This device complies
with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. For
product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operation in conjunction with any
other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

Table of Contents

iii AirLive WIAS-3200N v2 User’s Manual

Table of Contents

1. BEFORE YOU START................................................................................................ 1

1.1 PREFACE..............................................................................................................................................1

1.2 PACKAGE CHECKLIST............................................................................................................................ 2

2. GETTING STARTED WITH EASY SETUP UTILITY................................................... 3

2.1 INTRODUCE ..........................................................................................................................................3

2.2 SYSTEM CONCEPT................................................................................................................................3

2.3 HARDWARE DESCRIPTIONS ...................................................................................................................4

2.3.1 Front Panel.................................................................................................................................. 4

2.3.2 Rear Panel...................................................................................................................................5

2.3.3 Top LED Panel.............................................................................................................................6

2.4 SYSTEM REQUIREMENT.........................................................................................................................7

2.5 INSTALLATION STEPS ............................................................................................................................7

2.6 EASY SETUP.........................................................................................................................................8

2.7 ACCESS WEB MANAGEMENT INTERFACE..............................................................................................10

3. CONFIGURE HOTSPOT TO NETWORK ................................................................. 13

3.1 NETWORK REQUIREMENT....................................................................................................................13

3.2 WAN ................................................................................................................................................. 13

3.2.1 Static IP .....................................................................................................................................13

3.2.2 Dynamic IP ................................................................................................................................14

3.2.3 PPPoE....................................................................................................................................... 14

3.2.4 PPTP .........................................................................................................................................15

3.2.5 DNS........................................................................................................................................... 15

3.2.6 MAC Clone ................................................................................................................................16

3.3 WAN TRAFFIC....................................................................................................................................16

3.3.1 Load Balance.............................................................................................................................17

3.3.2 Backup.......................................................................................................................................17

3.3.3 Connection Detect..................................................................................................................... 17

3.4 LAN/VLAN ........................................................................................................................................ 19

3.4.1 VLAN Setup...............................................................................................................................19

3.4.2 LAN/VLAN List...........................................................................................................................19

3.4.3 LAN Setup (Domain0) ...............................................................................................................20

3.4.4 VLAN Setup (Domain1-3)..........................................................................................................20

3.4.5 Bandwidth Control .....................................................................................................................20

3.4.6 DHCP Server .............................................................................................................................23

3.4.7 Static Lease List ........................................................................................................................24

3.5 DYNAMIC DNS ................................................................................................................................... 24

3.6 MANAGEMENT ....................................................................................................................................25

3.6.1 System Information....................................................................................................................26

3.6.2 Root Password ..........................................................................................................................26

3.6.3 Admin Password........................................................................................................................26

3.6.4 Operator Password....................................................................................................................27

3.6.5 Login Methods........................................................................................................................... 27

3.6.6 E-mail SMTP Relay ...................................................................................................................28

3.6.7 Ping Watchdog ..........................................................................................................................29

3.7 TIME SERVER .....................................................................................................................................30

3.7.1 System Time.............................................................................................................................. 30

3.7.2 Setup Time Use NTP................................................................................................................. 30

3.7.3 User Setup.................................................................................................................................31

3.7.4 Time Display Format ................................................................................................................. 31

3.8 SNMP ............................................................................................................................................... 32

Table of Contents

Ai

rLive WIAS-3200N v2 User’s Manual

iv

3.8.1 SNMP v2c.................................................................................................................................. 32

3.8.2 SNMP v3.................................................................................................................................... 32

3.8.3 SNMP Trap ................................................................................................................................32

4. CONFIGURE SERVICE DOMAIN............................................................................. 33

4.1 SERVICE DOMAIN................................................................................................................................33

4.1.1 Service Domain .........................................................................................................................34

4.2 AUTHENTICATION................................................................................................................................37

4.2.1 Authentication Management......................................................................................................37

4.2.2 Pregenerate Ticket ....................................................................................................................38

4.2.3 On-Demand ................................................................................................................................45

4.2.3.1 Billing Plan Setup ...................................................................................................................................50

4.2.3.2 Payment Gateway ..................................................................................................................................53

4.2.3.3 Thermal Printer Setup ............................................................................................................................56

4.2.3.4 Billing Plan Report..................................................................................................................................60

4.2.3.5 Ticket Customization ..............................................................................................................................62

4.2.4 Local RADIUS Accounts............................................................................................................63

4.2.5 Remote RADIUS Accounts........................................................................................................67

4.2.6 Clear Tickets..............................................................................................................................68

4.3 PRIVILEGE IP/MAC ADDRESS .............................................................................................................68

4.4 WALLED GARDEN ...............................................................................................................................69

4.5 BLACKLIST..........................................................................................................................................71

4.6 NOTIFICATION.....................................................................................................................................72

4.7 ONLINE USERS ...................................................................................................................................77

4.8 LOG INFO ...........................................................................................................................................78

5. CONFIGURE WIRELESS CONNECTION ................................................................ 80

5.1 GENERAL SETUPS ..............................................................................................................................80

5.2 ADVANCED SETUP .............................................................................................................................. 82

5.3 VIRTUAL AP SETUP.............................................................................................................................85

5.3.1 VAP0-3 Setup ............................................................................................................................86

5.3.1.1 Security ..................................................................................................................................................87

5.3.1.2 WDS .......................................................................................................................................................93

5.3.2 Wireless MAC Filter...................................................................................................................94

5.4 ASSOCIATED CLIENTS......................................................................................................................... 96

5.5 WDS STATUS..................................................................................................................................... 97

6. ADVANCE FUNCTIONS........................................................................................... 98

6.1 DMZ.................................................................................................................................................. 98

6.2 IP FILTER ...........................................................................................................................................98

6.3 MAC FILTER.....................................................................................................................................100

6.4 VIRTUAL SERVER..............................................................................................................................101

6.5 TIME POLICY ....................................................................................................................................102

7. NETWORK UTILITIES............................................................................................ 104

7.1 PROFILE SETTING (BACKUP/RESTORE AND RESET TO FACTORY).........................................................104

7.2 FIRMWARE UPGRADE........................................................................................................................105

7.3 NETWORK UTILITY ............................................................................................................................105

7.4 FORMAT DATABASE...........................................................................................................................107

7.5 REBOOT ........................................................................................................................................... 108

8. VIEW SYSTEM LOG & STATUS ............................................................................ 109

8.1 OVERVIEW........................................................................................................................................109

8.2 EXTRA INFO ..................................................................................................................................... 110

8.3 EVENT LOG.................................................................................................................................. .... 113

APPENDIX A. SPECIFICATIONS .................................................................................. 114

Table of Contents

v AirLive WIAS-3200N v2 User’s Manual

APPENDIX B. WEB UI VALID CHARACTERS.............................................................. 122

APPENDIX C. SYSTEM MANAGER PRIVILEGES........................................................ 131

APPENDIX D. CREATE PAYPAL BUSINESS ACCOUNT............................................ 133

APPENDIX E. EXAMPLE OF MAKING PAYMENTS FOR END USERS ....................... 137

APPENDIX F. ISSUE REFUND FOR PAYPAL ............................................................... 141

APPENDIX G. NETWORK CONFIGURATION ON PC & USER LOGIN ........................ 145

APPENDIX H. USING STB CONNECTOR FOR POWER INPUT ................................... 164

1. Before You Start

1 AirLive WIAS-3200N v2 User’s Manual

1

1. Before You Start

1.1 Preface

This manual is for WLAN service providers or network administrators to set up a network
environment using the hotspot system. It contains step-by-step procedures and graphic
examples to guide MIS staff or individuals with slight network system knowledge to
complete the installation.

1. Before You Start

AirLive WIAS-3200N v2 User’s Manual

2

1.2 Package Checklist

The standard package of WIAS-3200N v2 includes:

 WIAS-3200N v2 x 1

 CD-ROM (with User’s Manual and QIG) x 1

 Quick Installation Guide (QIG) x 1

 Ethernet Cable x 1

 Power Adapter (DC 12V,1A) x 1

 Antenna x 2

 Ground Cable x 1

*Note: It is highly recommended to use all the supplies in the package instead of
substituting any components by other suppliers to guarantee bests performance.

2 Getting Started with Easy Setup Utility

3 AirLive WIAS-3200N v2 User’s Manual

2

2. Getting Started with Easy

Setup Utility

2.1 Introduce

The WIAS-3200N v2 is the most economical and feature rich Wireless Hotspot Gateway,
targeting mini-size stores that want to provide small, single-point wireless Internet access
service. WIAS-3200N v2 is a perfect choice for beginners to run hotspot businesses. It
does not cost much compared to buying a pile of equipments, nor does it take the skills of
an expert to glue multiple applications out of multiple freeware. Feature-packed for hotspot
operation, WIAS-3200N v2 comes with built-in 802.11 n/b/g MIMO access point, web
server and web pages for clients to login, easy logo-loading for branding a hotspot store,
simple user/visitor account management tool, payment plans, credit card gateway, traffic
logs, IP sharing , Firewall, Multi-WAN and Qos etc.

One single WIAS-3200N v2 can serve up to 100 simultaneous users, takes control over
authentication, authorization, accounting and routing to the Internet as well as to the
operating central. Built-in AAA system allows hotspot owners set up public access services
without extra RADIUS server.

WIAS-3200N v2 also brings in an extra advantage - the wall-mountable, dust-proof (IP50)
metal housing.

2.2 System Concept

WIAS-3200N v2 is capable of managing user authentication, authorization and accounting.
The user account information is stored in the local database or a specified external
RADIUS database server. Featured with user authentication and integrated with external
payment gateway, WIAS-3200N v2 allows users to easily pay the fee and enjoy the
Internet service using credit cards through a variety of payment gateways including PayPal.
Furthermore, WIAS-3200N v2 introduces the concept of Zones – Private Zone and Public
Zone, each with its own definable access control profiles. Private Zone means clients are
not required to be authenticated before using the network service. On the other hand,
clients in Public Zone are required to get authentication before using the network service.
This is very useful for hotspot owners seeking to deploy wireless network service for clients
and manage the network as well. The following diagram is an example of WIAS-3200N v2
set to manage the Internet and network access services at a hotspot venue.

2. Getting Started with Easy Setup Utility

AirLive WIAS-3200N v2 User’s Manual

4

2.3 Hardware Descriptions

2.3.1 Front Panel

No.

Connector Description

1

USB For future usage only.

2

Scan Button

There are two functions for Scan button as following.

 Scan New Channel

Press and hold the Scan button for 3 seconds until
STATUS LED FLASH and release to Scan New AP's
Channel.

2 Getting Started with Easy Setup Utility

5 AirLive WIAS-3200N v2 User’s Manual

 Reset to factory default

Press and hold the Scan button for more than 10
seconds until SYSTEM LED FLASH to reset the system
to default configurations.

3

Console Attach the RS-232 console cable here, for management use

only.

4

WAN1/WAN2 Attach Ethernet cables here for connecting to the wired local

network. LAN1 maps to Private Zone and requires no user
authentication, LAN2 maps to Public Zone and by default
requires user authentication.

5

LAN (PoE) Attach the wired external network here. This port supports

Power over Ethernet (PoE) for flexible installation.

6

Reset This is hardware reset button. Press once to restart the

system.

7

STB Connector for
Power Apply

For connecting power input via STB, please refer “Appendix
H. Using STB connector for power input” for more detail.

8

Power Socket

(12VDC/1A)

For connecting to external power supply via the power
adapter.

2.3.2 Rear Panel

Connector Description

Antenna Connector Attach antennas here. WIAS-3200N v2 supports 1 RF

interface with 2 SMA connectors.

2. Getting Started with Easy Setup Utility

AirLive WIAS-3200N v2 User’s Manual

6

2.3.3 Top LED Panel

No.

Connector Description

1 Power LED ON indicates power on; OFF indicates power off.

2 LAN LED ON indicates LAN connection; OFF indicates no connection;

BLINKING indicates transmitting data.

3 WAN2

4 WAN1

LED ON indicates WAN connection; OFF indicates disconnection;
BLINKING indicates transmitting data.

5 WLAN LED ON indicates wireless ready.

6 PRINT LED ON thermal ticket printer is ready.

7 SYSTEM

LED ON/FLASH indicates Flash busy, OFF indicates Flash Idle

8 Status LED ON indicates System up, OFF indicates down, FLASH

indicates Scan button activated.

2 Getting Started with Easy Setup Utility

7 AirLive WIAS-3200N v2 User’s Manual

2.4 System Requirement

 Standard 10/100BaseT including network cables with RJ-45 connectors

 All PCs need to install the TCP/IP network protocol

2.5 Installation Steps

Please follow the steps below to install WIAS-3200N v2:

Please follow the steps mentioned below to install the hardware of WIAS-3200N v2:

Step 1. Place the WIAS-3200N v2 at a best location.

The best location for WIAS-3200N v2 is usually at the center of your wireless network.

Step 2. Connect WIAS-3200N v2 to your outbound network device.

Connect one end of the Ethernet cable to the WAN port of WIAS-3200N v2 on the front
panel. Depending on the type of internet service provided by your ISP, connect the other
end of the cable to the ATU-Router of an ADSL, a cable modem, a switch or a hub. The
WAN LED indicator should be ON to indicate a proper connection.

Step 3. Connect WIAS-3200N v2 to your network device.

Connect one end of the Ethernet cable to the LAN port of WIAS-3200N v2 on the front
panel. Connect the other end of the cable to a PC for configuring the system. The LAN LED
indicator should be ON to indicate a proper connection.

1. There are two ways to supply power over to WIAS-3200N v2.

(a) Connect the DC power adapter to the WIAS-3200N v2 power socket on the front

panel.

(b) WIAS-3200N v2 is capable of transmitting DC current via its WAN PoE port.

Connect an IEEE 802.3af-compliant PSE device, e.g. a PoE-switch, to the WAN
port of WIAS-3200N v2 with the Ethernet cable.

2. Now, the hardware installation is completed.

*Caution!! Please only use the power adapter supplied with the WIAS-3200N v2 package.

Using a different power adapter may damage this system.

2. Getting Started with Easy Setup Utility

AirLive WIAS-3200N v2 User’s Manual

8

*Caution!! To double verify the wired connection between WIAS-3200N v2 and your

switch/router/hub, please check the LED status indication of these network devices.

2.6 Easy Setup

Web UI Wizard

Please click the System >
Wizard to start the setup wizard.

Step 1. Select Internet

Interface

Please select what internet
connection you have, and then
click “Next” to continue.

Step 2. WAN Setting

Configure your WAN connection
type, and then click “Next” to
continue.

2 Getting Started with Easy Setup Utility

9 AirLive WIAS-3200N v2 User’s Manual

Step 3. Hotspot Zone Setting

Please configure the Zone SSID
and Hotspot Authentication type.
We have choice the WPA2-PSK
security type for you. If you want
to want to change to other
security type, please go to
"Wireless > Virtual AP Setup
>VAP0 Setup".

And, then click “Next” to
continue.

Step 4.

Hotspot Zone Billing Plan

Please configure your On-Demand
Billing Plan, and then click “Next” to
continue.

Step 5. Finish and Reboot

Please click on the "Finish"
button if you have entered all the
information correctly. It will take
about 2 minutes to reboot. After
reboot, you will use the SSID
you entered, and please select
the SSID and connect it.

2. Getting Started with Easy Setup Utility

AirLive WIAS-3200N v2 User’s Manual

10

2.7 Access Web Management Interface

When Hotspot mode is activated, the system can be configured as a Wireless Hotspot
Gateway. This section provides information in configuring the Hotspot mode with graphical
illustrations. WIAS-3200N v2 provides functions as stated below where they can be
configured via a user-friendly web based interface.

System

Service
Domain

Wireless Advanced Utilities Status

WAN

Service

Domain

General

Setup

DMZ Profile Setting Overview

WAN Traffic Authentication

Advanced

Setup

IP Filter

Firmware

Upgrade

Extra Info

LAN/VLAN Privilege List

Virtual AP

Setup

MAC Filter

Network

Utility

Event Log

DDNS

Walled

Garden

Associated

Clients

Virtual Server

Format

Database

Management Notification WDS Status Time Policy

Reboot

Time Server Online Users

SNMP Log Info

*Note: After finishing the configuration of the settings, please click Save button and pay
attention to see if a Reboot message appears on the screen. If such message appears,
system must be restarted to allow the settings to take effect. All online users will be
disconnected during restart.

WIAS-3200N v2 supports Web Management Interface (WMI) configuration. Upon the
completion of hardware installation, WIAS-3200N v2 can be configured via web browsers
with JavaScript enabled such as Internet Explorer version 6.0 and above or Firefox.

Default LAN interface IP address is 192.168.1.254.

2 Getting Started with Easy Setup Utility

11 AirLive WIAS-3200N v2 User’s Manual

To access the web management interface, connect a PC to the LAN Port, and then launch
a browse. Make sure you have set DHCP in TCP/IP of your PC to get an IP address
dynamically. The default gateway IP address is the default gateway IP address of Private
Zone: “192.168.1.254”.

Next, enter the gateway IP address of WIAS-3200N v2 at the address field. The default
gateway IP address from LAN Port is http://192.168.1.254.

The administrator login page will appear. Enter “root”, the default username, and “airlive”,
the default password, in the User Name and Password fields. Click LOGIN to log in.

After a successful login, a “Home” page with six main buttons will appear on the screen.

2. Getting Started with Easy Setup Utility

AirLive WIAS-3200N v2 User’s Manual

12

(“https” is used for a secured connection).

For the first time, if WIAS-3200N v2 is not using a trusted SSL certificate, there will be a
“Certificate Error” when enable https login, because the browser treats WIAS-3200N v2 as
an illegal website. Please press “Continue to this website” to continue.

*Caution!!!

If you can’t get the login screen, the reasons may be:

(1) The PC is set incorrectly so that the PC can’t obtain the IP address automatically
from the LAN port;

(2) The IP address and the default gateway are not under the same network segment.
Please set your PC with a static IP address such as 192.168.1.xx in your network and
then try it again. For the configuration on PC, please refer to “Appendix G. Network
Configuration on PC & User Login”.

3 Configure Hotspot to Network

13 AirLive WIAS-3200N v2 User’s Manual

3

3. Configure Hotspot to

Network

3.1 Network Requirement

In the general network environment, the main role of WIAS-3200N v2 is a gateway that
manages all the network access from internal network to Internet. Thus, the first step is to
prepare an Internet connection from your ISP (Internet Service Provider) and connect it to
the WAN port of WIAS-3200N v2.

3.2 WAN

There are 3 connection types for the WAN Port: Static IP, Dynamic IP, PPPoE and PPTP.

Now, let us discuss how to configure WAN port. Please click on System > WAN and follow
the below setting.

3.2.1 Static IP

The administrator can manually setup the WAN IP address when static IP is available/
preferred.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

14

 IP Address: The IP address of the WAN port.

 IP Netmask : The Subnet mask of the WAN port.

 IP Gateway: The IP address of the host router which resides on the external network

and provides the point of connection to the next hop towards the Internet. This can be
a DSL modem, Cable modem, or a WISP gateway router. AC-920X will direct all the
packets to the gateway if the destination host is not within the local network.

Gateway IP address should be from the same address space (on the same network
segment) as the AC-920X's external network interface.

3.2.2 Dynamic IP

This configuration type is applicable when the WIAS-3200N v2 is connected to a network
with the presence of a DHCP server; all related IP information will be provided by the
DHCP server automatically. If the IP Address does not assigned from DHCP server, the
system need manual connect to DHCP server.

 Hostname : The Hostname of the WAN port

3.2.3 PPPoE

This configuration type is applicable when the WIAS-3200N v2 is connected to a network
with the presence of a PPPoE server.

 User Name : Enter User Name for PPPoE connection

 Password : Enter Password for PPPoE connection

 MTU: MTU stands for Maximum Transmission Unit. For PPPoE connections, you may

need to set the MTU setting in order to work correctly with your ISP. Default is 1492
bytes.

3 Configure Hotspot to Network

15 AirLive WIAS-3200N v2 User’s Manual

3.2.4 PPTP

The Point-to-Point Tunneling Protocol (PPTP) mode enables the implementation of secure
multi-protocol Virtual Private Networks (VPNs) through public networks.

 Username : Enter User Name for PPTP connection .(You can set 0-32 alphanumeric

and ~!@#$%^*()_+-:<>?[]/;,.= specific characters)

 Password: Enter Password for PPTP connection. (You can set 0-32 alphanumeric

and ~!@#$%^*()_+-:<>?[]/;,.= specific characters)

 PPTP Server IP Address : The IP address of the PPTP server

 My WAN IP : The IP address of the WAN port

 My WAN IP Netmask : The Subnet mask of the WAN port

 MTU: The range is 1400-1460, default is 1460 bytes. MTU stands for Maximum

Transmission Unit. Consult with WISP for a correct MTU setting.

 MPPE Encryption: Microsoft Point-to-Point Encryption (MPPE) encrypts data in

Point-to-Point Protocol (PPP)-based dial-up connections or Point-to-Point Tunneling
Protocol (PPTP) virtual private network (VPN) connections. 128-bit key (strong) and
40-bit key (standard) MPPE encryption schemes are supported. MPPE provides data
security for the PPTP connection that is between the VPN client and the VPN server.

3.2.5 DNS

You can select “No Default DNS Server” or “Specify DNS Server IP” radial button as
desired to set up system DNS.

 Primary: The IP address of the primary DNS server.

 Secondary: The IP address of the secondary DNS server.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

16

3.2.6 MAC Clone

The MAC address is a 12-digit HEX code uniquely assigned to hardware as identification.
Some ISPs require you to register a MAC address in order to access to Internet. If not, you
could use default MAC or clone MAC from a PC.

 Keep Default MAC Address: Keep the default MAC address of WAN port on the

system.

 Clone MAC Address: If you want to clone the MAC address of the PC, then click the

“Clone MAC Address” button. The system will automatically detect your PC's MAC
address.

* Note: The Clone MAC Address field will display MAC address of the PC connected to
system. Click Save button can make clone MAC effective.

 Manual MAC Address: Enter the MAC address registered with your ISP.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

3.3 WAN Traffic

The section is for administrators to configure the control over the entire system’s traffic
though the WAN interface (WAN1 and WAN2 ports). To configure WAN Traffic, please go
to: System > WAN Traffic.

 Primary WAN Interface: Select desired primary WAN interface for system.

 Traffic Mode: There are three types: None, Load Balance and Backup.

3 Configure Hotspot to Network

17 AirLive WIAS-3200N v2 User’s Manual

3.3.1 Load Balance

Outbound load balancing is supported by the system. When enabled, the system will
allocate traffic between WAN1 and WAN2 dynamically according to designed algorithms
based on the Bandwidth.

 WAN1 Max. Bandwidth: Specify the maximum download and upload bandwidth that

can be shared by clients of the WAN1 port.(Download/Upload range is 128-102400
Kbit/s, default is 10240 Kbit/s)

 WAN2 Max. Bandwidth: Specify the maximum download and upload bandwidth that

can be shared by clients of the WAN2 port. (Download/Upload range is 128-102400
Kbit/s, default is 10240 Kbit/s)

* Note: On the Load Balance traffic mode, the primary WAN port is WAN1. When the
WAN1 connection is down, the WAN2 will backup automatically.

3.3.2 Backup

When primary WAN interface is WAN1 and WAN2 is available, WAN1's traffic will be routed
to WAN2 when WAN1 connection is down. When WAN1 connection is up, the route traffic
will be connected back to WAN1 automatically.

3.3.3 Connection Detect

The Connect Detect sets the WIAS-3200N v2 to continuously ping a user defined IP
address (it can be the Internet gateway for example). If it is unable to ping under the user
defined constraints, the WIAS-3200N v2 t will change Primary WAN interface to
secondary WAN interface automatically. This option is only for “Load Balance” or
“Backup” traffic mode.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

18

 Service: By default, it's “Disable”. To “Enable” to activate this function.

 IP Address To Ping : specify an IP address of the target host which will be monitored

 Ping Interval: specify time interval (in seconds) between the ICMP “echo requests”

are sent. (The range is 60-3600, default is 60 seconds.)

 Startup Delay: specify initial time delays (in seconds) until first ICMP “echo requests”

are sent. The value of Startup Delay should be at least 60 seconds as the network
interface and wireless connection initialization takes considerable amount of time if the
device is rebooted. (The range is 60-3600, default is 60 seconds.)

 Failure Count: specify the number of ICMP “echo response” replies. If the specified

number of ICMP “echo response” packets is not received continuously, the primary
WAN traffic will be routed secondary WAN. (The range is 1-99, default is 1.)

* Note: If Connection Detect is disabled on “Load Balance” or “Backup”, the system will
use default value.

* Note: if “Connection Detection” is disabled and the PHY's connection status shows Red

(Status > Port Link Info). The system will detect PHY on every 5 seconds. When system

detects failure 1 times, the traffic of package will routed via Secondary WAN Interface.
When Primary WAN Interface detects 1 time success, the traffic of package will routed via
Primary WAN Interface.

If “Connection Detection” is disabled and the PHY's connection is Green (Status > Port
Link Info), the system will detect remote Gateway IP address of Primary WAN on every 5
seconds. When system detects failure 3 times, the traffic of package will routed via
Secondary WAN Interface. When Primary WAN Interface detects 1 time success, the
traffic of package will routed via Primary WAN Interface.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

Here is the instruction for how to setup the local LAN/VLAN IP Address and Netmask.
Please click on System > LAN/VLAN, the LAN/VLAN List should be appear. This page
shows information of LAN's/VLAN's settings.

3 Configure Hotspot to Network

19 AirLive WIAS-3200N v2 User’s Manual

3.4 LAN/VLAN

3.4.1 VLAN Setup

 VLAN No. : Denote the system's VLAN port.

 VLAN Tag (ID): Denote the VLAN tag of the respective VLAN port. Only for VLAN1 ~

VLAN3.

 VAP0-VAP3: Select specify the LAN/VLAN port for VAP. The packets from VAP to LAN

will insert specify VLAN tag

 WDS: Select specify the LAN/VLAN port for WDS. The packets from WDS to LAN will

insert specify VLAN tag

3.4.2 LAN/VLAN List

 VLAN No. : Denote the system's VLAN port.

 VLAN Tag (ID): Denote the VLAN tag of the respective VLAN port. Only for VLAN1 ~

VLAN3.

 IP Address: Denote the IP address of the respective LAN/VLAN port.

 Bandwidth Control(p/Down Kb):

(1) Individual: Denote the Individual Max. Upload/Download of the respective

LAN/VLAN port.

(2) Group: Denote the Group Upload/Download of the respective LAN/VLAN port.

(3) Distribution: Denote the Distribution Upload/Download of the respective

LAN/VLAN port.

(4) Session: Denote the Session of the respective LAN/VLAN port.

 DHCP: Denote the DHCP server status of the respective LAN/VLAN.

 Actions: Click this option to configure LAN/VLAN's settings, the setup page should be

appear. Below depicts an example for LAN.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

20

3.4.3 LAN Setup (Domain0)

 IP Address: The IP address of the LAN port, and the he default LAN's IP address as

192.168.1.254,

 IP Netmask : The Subnet mask of the VLAN port; default Netmask is 255.255.255.0

3.4.4 VLAN Setup (Domain1-3)

 VLAN Tag (ID): Virtual LAN, the system supports 3 tagged VLAN port (VLAN1 ~

VLAN3). The valid values are from 1 to 4094. The default VLAN1's tag ~ VLAN3's tag
are from 101 to 103.

*Note: Some system and VLAN switch do not support VLAN tag 1

 IP Address: The IP address of VLAN port, default VLAN1's ~ VLAN3's IP address as

192.168.101.1 ~ 192.168.103.1.

 IP Netmask : The Subnet mask of the VLAN port; default Netmask is 255.255.255.0

3.4.5 Bandwidth Control

3 Configure Hotspot to Network

21 AirLive WIAS-3200N v2 User’s Manual

 Bandwidth Control: By default, it's “Disable”. To “Enable” to use bandwidth control.

 Type : Enable the desire option among “Even Distribution of Bandwidth” or

“Individual Bandwidth”

(1) Even Distribution of Bandwidth: Set users distribute Total Max. Upload/Download.

Below depicts an example for Even Distribution of Bandwidth, set Total Max.
Upload or Download to 9 Mbps, if one user access Internet, the maximum upload or
download is 9 Mbps; if three users access Internet at the same time, the maximum
upload or download is 3 Mbps by each user.

 Total Max. Upload: The Total Max. Upload is in the range of 0~102400 Kbit/s, 0

indicates unlimited, default is 512 Kbit/s

 Total Max. Download: The Total Max. Download is in the range of 0~102400 Kbit/s, 0

indicates unlimited; default is 512 Kbit/s.

*Note: If the system does not enable any authentication function, all users of the

bandwidth control will be based by the “Total Max. Upload” and “Total Max. Download”

If the system enable authentication function and user in the privilege list, the user of
bandwidth will be uncontrolled by Even Distribution of Bandwidth

(2) Individual Bandwidth: Set each users Individual Upload/Download. Below depicts an

example for Individual Bandwidth, set Group Upload or Download to 6 Mbps and
Individual Upload or Download to 3 Mbps, if one user access Internet, the maximum
upload or download is 3 Mbps; if three users access Internet at the same time, the
maximum upload or download is 3 Mbps by each user.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

22

 Individual Upload : The Individual Upload is in the range of 0~102400 Kbit/s, 0

indicates unlimited, default is 512 Kbit/s

 Individual Download : The Individual Download is in the range of 0~102400 Kbit/s, 0

indicates unlimited, default is 512 Kbit/s

 Group Total Limit: By default, it's “Disable”. To “Enable” to activate Group Total

Limit.

 Group Upload : The Group Upload is in the range of 0~102400 Kbit/s, 0 indicates

unlimited, default is 512 Kbit/s

 Group Download : The Group Download is in the range of 0~102400 Kbit/s, 0

indicates unlimited, default is 512 Kbit/s

3 Configure Hotspot to Network

23 AirLive WIAS-3200N v2 User’s Manual

*Note: If the system enable authentication function and user in the privilege list, the user

of bandwidth will be uncontrolled by Individual Bandwidth

 Guest Service: By default, it's “Disable”. To Enable to activate bandwidth control

service for guest users.

 Guest Upload : The Guest Upload is in the range of 0~102400 Kbit/s, 0 indicates

unlimited, default is 512 Kbit/s

 Guest Download : The Guest Download is in the range of 0~102400 Kbit/s, 0

indicates unlimited, default is 512 Kbit/s

 Session Limit per IP: The number of sessions is in the range of 10~500, 0 indicates

unlimited, default is 0.

 STP: By default, it's “Disable”. To “Enable” to activate STP. the spanning tree network

protocol provides a loop free topology for any bridged LAN/VLAN. The Spanning Tree
Protocol, which is also referred to as STP, is defined in the IEEE Standard 802.1d.

3.4.6 DHCP Server

 Service: Check “Enable” to activate DHCP Server on VLAN/LAN port.

 Start IP / End IP: Specify the range of IP addresses to be used by the DHCP server

when assigning IP address to clients.

 DNS1 / DNS2 IP: The Domain Name System (DNS) is an Internet "phone book" which

translates domain names to IP addresses. These fields identify the server IP
addresses where the DNS requests are forwarded by the WIAS-3200N v2.DNS1
server IP is mandatory. It is used by the DNS Proxy and for the device management
purpose. DNS2 server IP address is optional. It is used as the fail-over in case the
primary DNS server will become unresponsive.

 WINS IP: Enter IP address of the Windows Internet Name Service (WINS) server; this

is optional.

 Domain: Enter the domain name for this network.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

24

 Lease Time: The IP addresses given out by the DHCP server will only be valid for the

duration specified by the lease time. Increasing the time ensure client operation
without interrupt, but could introduce potential conflicts. Lowering the lease time will
avoid potential address conflicts, but might cause more slight interruptions to the client
while it will acquire new IP addresses from the DHCP server.

3.4.7 Static Lease List

If you want a computer or device to always have the same IP address assigned, you can
create a static lease. The system will assign the IP address only to that computer or device.
There are maximum 50 rules allowed in this list.

 Hostname: Enter the hostname of the computer or device.

 IP Address: Enter the IP address you want to assign to the computer or device. This

IP Address must be within the DHCP IP Address Range.

 MAC Address: Enter the MAC address of the computer or device.

 Actions: Click an action button to perform the appropriate action.

 Delete: Click this button to remove the lease for a specific LAN device and free an

entry in the lease table.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes.

3.5 Dynamic DNS

Dynamic DNS allows you to make an assumed name as a dynamic IP address to a static
hostname. Please click on System > DDNS and follow the below setting.

3 Configure Hotspot to Network

25 AirLive WIAS-3200N v2 User’s Manual

 Enabled: Select Enable for DDNS function, each time your IP address for WAN is

changed, the information will be updated to DDNS service provider automatically.

 Service Provider: Select the correct Service Provider from the drop-down list, here

included are dyndns, dhs, ods and tzo embedded in the WIAS-3200N v2.

 Hostname: This field represents the Host Name you register to Dynamic-DNS service

and expect to export to the world. (You can set 1-32 alphanumeric and @-_. specific
characters)

 User Name & Password: User Name and Password is used as an identity to login

DDNS service. (You can set 1-32 alphanumeric and ~!@#$%^*()_+-:<>?[]/;,.= specific
characters)

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

3.6 Management

The administrator can later obtain the geographical location of the system via the
information configured here. The administrator also can change system password and
configure system login methods. Please click System > Management and follow the
below settings.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

26

3.6.1 System Information

 System Name: Enter a desired name or use the default provided.

 Description: Denote further information of the system.

 Location: Enter related geographical location information of the system;

administrator/manager will be able to locate the system easily.

3.6.2 Root Password

Log in as a root user and is allowed to change its own. Root user also can change admin
user's and operator user's password. Click Save button to activate the new password.
(Default password is airlive)

 New Password: Please input the new password of administrator.

 Check New Password: Please input again the new password of administrator.

3.6.3 Admin Password

Log in as a admin user and is allowed to change its own. Admin user also can change
operator user’s password. Click Save button to activate the new password. (Default
password is airlive)

3 Configure Hotspot to Network

27 AirLive WIAS-3200N v2 User’s Manual

 New Password: Please input the new password of administrator.

 Check New Password: Please input again the new password of administrator.

3.6.4 Operator Password

Log in as a operator user and is not allowed to change its own. Click Save button to
activate the new password. (Default password is airlive)

 New Password: Please input the new password of administrator.

 Check New Password: Please input again the new password of administrator.

3.6.5 Login Methods

Admin Login Methods, the admin manager can enable or disable system login methods; it
also can change services port. Click Save button to activate the admin login methods.

 Enable HTTP: Select Enable HTTP to activate HTTP Service

 HTTP Port: Please input 1 ~ 65535 value to set HTTP Port; default value is 80.

 Enable HTTPS: Select Enable HTTPS to activate HTTPS Service.

 HTTPS Port: Please input 1 ~ 65535 value to set HTTPS Port; default value is 443.

Without a valid certificate, users may encounter the following problem in IE8 when they try
to access WIAS-3200N v2 GUI (https://192.168.1.254). There will be a “Certificate Error”,
because the browser treats WIAS-3200N v2 as an illegal website.

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

28

Click “Continue to this website” to access the WIAS-3200N v2's GUI. The WIAS-3200N
v2's Home page will be appearing.

*Note: If you already have an SSL Certificate, please click UploadKey button to select the
file and upload it.

 Enable Telnet: Select Enable Telnet to activate Telnet Service

 Telnet Port: Please input 1 ~ 65535 value to set Telnet Port; default value is 23.

 Enable SSH: Select Enable SSH to activate SSH Service

 SSH Port: Please input 1 ~ 65535 value to set SSH Port; default value is 22.

*Note: Click GenerateKey button to generate RSA private key. The “Display the host key
footprint” gray blank will be show content of RSA key.

3.6.6 E-mail SMTP Relay

Select Enable Service to activate Email SMTP Relay function. Enter SMTP relay server in
IP Address/ Domain field.

3 Configure Hotspot to Network

29 AirLive WIAS-3200N v2 User’s Manual

3.6.7 Ping Watchdog

The ping watchdog sets the WIAS-3200N v2 to continuously ping a user defined IP
address (it can be the Internet gateway for example). If it is unable to ping under the user
defined constraints, the WIAS-3200N v2 will automatically reboot. This option creates a
kind of "fail-proof" mechanism.

Ping Watchdog is dedicated for continuous monitoring of the particular connection to
remote host using the Ping tool. The Ping works by sending ICMP “echo request” packets
to the target host and listening for ICMP “echo response” replies. If the defined number of
replies is not received, the tool reboots the device.

 Enable Ping Watchdog: control will enable Ping Watchdog Tool.

 IP Address to Ping: specify an IP address of the target host which will be monitored

by Ping Watchdog Tool.

 Ping Interval: specify time interval (in seconds) between the ICMP “echo requests”

are sent by the Ping Watchdog Tool. Default is 300 seconds.

 Startup Delay: specify initial time delay (in seconds) until first ICMP “echo requests”

are sent by the Ping Watchdog Tool. The value of Startup Delay should be at least 60
seconds as the network interface and wireless connection initialization takes
considerable amount of time if the device is rebooted. Default is 300 seconds.

 Failure Count To Reboot: specify the number of ICMP “echo response” replies. If the

specified number of ICMP “echo response” packets is not received continuously, the
Ping Watchdog Tool will reboot the device.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

30

3.7 Time Server

System time can be configured via this page where manual setting and NTP server
configuration are both supported. Please click on System > Time Server and follow the
below setting.

3.7.1 System Time

Display the current time of the system.

3.7.2 Setup Time Use NTP

To enable Network Time Protocol, NTP, to synchronize the system time with NTP server.

 Default NTP Server: Select the NTP Server from the drop-down list.

 Time Zone: Please set a time zone from where the accurate time can be supplied,

(GMT+08:00) Taipei for example.

 Daylight saving time: Enable Daylight saving time from where the accurate time

needed.

*Note: If Time server setting selected in “Setup Time User NTP”, please verify system's
Default Gateway and DNS setting first.

3 Configure Hotspot to Network

31 AirLive WIAS-3200N v2 User’s Manual

3.7.3 User Setup

Administrator can set Time manually. Click Set Time button and Save button to change
Local Time.

3.7.4 Time Display Format

Administrator can set system's time format. Enter a desired time format or use the default
provided.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

3. Configure Hotspot to Network

AirLive WIAS-3200N v2 User’s Manual

32

3.8 SNMP

SNMP is an application-layer protocol that provides a message of format for
communication between SNMP managers and agents. By enabling SNMP function, the
administrator can obtain the system information remotely. Please click on System > SNMP

Setup and follow the below setting.

3.8.1 SNMP v2c

 Enable: Check to enable SNMP v2c.

 ro community : Set a community string to authorize read-only access.

 rw community : Set a community string to authorize read/write access.

3.8.2 SNMP v3

 Enable: Check to enable SNMP v3. SNMPv3 supports the highest level SNMP

security.

 SNMP ro user: Set a community string to authorize read-only access.

 SNMP ro password: Set a password to authorize read-only access.

 SNMP rw user: Set a community string to authorize read/write access.

 SNMP rw password: Set a password to authorize read/write access.

3.8.3 SNMP Trap

Events such as cold start, interface up & down, and association & disassociation will report
to an assigned server.

 Enable: Check to enable SNMP Trap.

 Community: Set a community string required by the remote host computer that will

receive trap messages or notices sends by the system.

 IP: Enter the IP addresses of the remote hosts to receive trap messages.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

4 Configure Service Domain

33 AirLive WIAS-3200N v2 User’s Manual

4

4. Configure Service Domain

4.1 Service Domain

WIAS-3200N v2 support 4 Service Domain, administrator can quick setup hotspot via this
page. Each VAP can move to different Domain.

 : Click tools icon on the top-right corner of each Domain settings window, the

Service Domain page will pop-up.

 LAN/VLAN : The bonding interface for this Service Domain

 Auth Type: The authentication type for this Service Domain. There are four types:

Pregenereated Ticket, On-demand, Local Users and Remote RADIUS Server.

 IP PnP Service: Denote the current status of IP PnP service on the respective

Service Domain.

 Guest Service: Denote the current status of guest service on the respective

Service Domain.

 Time Policy: Denote the schedule of authentication service on the respective

Service Domain.

 Redirect URL: Denote the redirect URL on this Login page of Service Domain.

 Login Domain Name : Denote the login domain name on the respective Service

Domain

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

34

 Login Page: The custom page for this Service Domain. There are two types :

Template page or Upload page

 : Click signal icon on each VAP field, the VAP Setup will pop-up.

4.1.1 Service Domain

Administrator can configure Service Domain with different authentication service type, IP
PnP service, guest free service, idle time , redirect URL, scheduling authentication service
and customization login page.

Click on Service Domain > Tools icon or Service Domain > Service Domain# to enter
Service Domain Setup page.

 Authentication Options: Select authentication type for this Service Domain. The

system supports multiple authentications in one Service Domain.

 Auth Type: Select desired authentication type for this Service Domain, each Domain

supports multiple authentications.

 Default Auth Type: Select default authentication type for this Service Domain.

 Pregenerated Ticket: Select desired tickets database for Pregenerated

authentication after creating the database of Pregenerated Tickets.

 Login Options: When authentication type selected in Auth Type, the Login Options

setting field will appear.

 Login Timeout: Enter idle timeout for this Service Domain. If users have idled with

no network activities, the system will automatically logout the users. The Login
Timeout can be set between 0 to 1440 minutes, and the default timeout is 10 minutes.

 Redirect URL: Enter the specified website to redirect, when users log in successfully,

the pop-up page will direct to the specified URL.

4 Configure Service Domain

35 AirLive WIAS-3200N v2 User’s Manual

 Login Domain Name: Enter the specified URL to display login page. If you close the

login page and because you can’t click Logout button to stop service, you can enter
specified URL on browser to display login page.

 Time Policy: Select desired scheduling of the respective Service Domain for

authentication service. Scheduling setting is on Time Policy page.

 IP PnP Service: IP Plug and Play, the AC-920X supports IP PnP for the respective

Server Domain. At the user end, a static IP address can be used to connect the
system. Regardless of what the IP address at the user end is, authentication can still
be performed through WIAS-3200N v2.

 Guest Service: By default; it's “Disable”. To Enable to activate guest service

limitation, the Guest button will appear on the login portal window. Below depicts an
example Guest Service.

 Guest Count Limit: Enter maximum number of guest to a desired number in the

range of 1-100. The default value is 5. For example, while the number of the guest is
set to 5, only 5 guests are allowed to connect to Internet via controller at the same
time.

 Guest Time: Enter maximum free service time for guest user within 24 hours. The

default is 10 Minutes; the range is between 1 to 720 Minutes.

 Custom Pages: Configure Custom pages for this Service Domain. Administrator can

select Template Page or Upload Customize Page.

 Template Page: Choose Template Page to make a customized login page. Click

select to pick up a color and then fill in all of the banks. You also can use Color
Template for your template. If you use Color Template, please click Apply button to
change all color. You can change the text as your wish. After finishing the setting, Click

Save button and Preview button to see the result.

6/17 12:00

6/17 00:00

Expired

Guest Time = 720 Minutes

Login

6/18 00:00

Free

Block

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

36

 Upload Page: Choose the Upload Page selection and click Upload button to upload

the designated page and photo. The upload files will be listed on the File List field.
Below depicts an example for upload File List. The file name of upload page must be

“login.html”

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

* Example for Upload Page:

Here the codes are supplied. Please note that the red part is for the login feature (can't not
modified), the green part can be modified freely by administrators.

<meta name="apple-mobile-web-app-capable" content="yes" /><!--Auto Login for Mac-->

<meta names="apple-mobile-web-app-status-bar-style" content="black" /><!--Auto Login

for Mac-->

<html>
<head>
<title><?hHotspot_main_title></title>

<?JAVASCRIPT>

</head>
<body>
<h1><?hHotspot_main_title></h1>
<p><?hHotspot_sub_title><p>

<div id="CW_MSG"></div><!--Main Login Form Content-->
<div id="CW_INFO"><span id="CW_HELP"></span></div><!--Main Help Content-->
<div id="WALLED"></div><!-- Walled Garden-->

<?hHotspot_footer_title>

</body>
</html>

4 Configure Service Domain

37 AirLive WIAS-3200N v2 User’s Manual

If login page need insert images or css file, please include path “/upload/vlan0/” ~
“/upload/vlan7/”, the “vlan0” ~”vlan7” indicate “Service Domain0” ~ “Server Domain7”,
below depicts an example for insert image001.gif image file to login page of Service
Domain0.

<img src="/upload/vlan0/image001.gif">

Below depicts an example for <div id="WALLED"></div> content

<div class="ad"><a href="http://www.google.com" title=""
target="_blank">Google</a></div>

You only can modify <div class="ad">, here is define CSS content for <div class="ad">
.ad{
float: left;

display: inline=block;
text-align: center;
width: 100px;
margin: 5px;
padding: 5px;
background: #fff;
font-size: 14px;
font-weight: bold;

}

.ad a{

text-decoration: none;
color: red;

}
.ad:hover, .ad a:hover, ad a:active{

background: #333333;
color: blue;

}

4.2 Authentication

WIAS-3200N v2 support 5 types of authentication: Pregenerated Tickets, On-Demand
Users, Local RADIUS Accounts, Remote RADIUS Server and Remote LDAP Server. This
section depicts to configure the settings for Pregenerated tickets, On-Demand users and
authentication server. If authentication selected in None, the clients can access Internet
without authentication.

4.2.1 Authentication Management

The WIAS-3200N v2 supports multiple login for one accounts and administrator can
configure alias name of the respective authentication type on login page. Please click on
Service Domain → Authentication → Authentication Management, and follow the
below setting.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

38

 Multiple Login: Select Enable to activate multiple login service, and Disable to

inactivate multiple login service.

 Auth Type: Denote authentication type of the system.

 Service Name: Enter desired alias name of the respective authentication type on

login page.

 Description: Enter desired description name of the respective authentication type.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes.

4.2.2 Pregenerate Ticket

This section is for administrators to Pregenerated authentication tickets for entire external
Network. There are three types of time policy ticket can be generated (One Time, Multiple

Times, Volume and Unlimited Until End Time). Please click on Service Domain >
Authentication > Pregenerated Tickets, and follow the below setting.

4 Configure Service Domain

39 AirLive WIAS-3200N v2 User’s Manual

Ticket Setting

 File ID: Enter the 8 hex digit numbers for identifying tickets database, this setting is

optional, If you don't specified file ID, the system will automatically generate. (The
range is 1-32767; Auto generated if no setting.)

 Price: The price charged for this tickets database.

 Currency : Select currency from drop-down list or enter customize currency for this

tickets database

 Quantity of Tickets: The range is 1-3066. To specify desired quantity of tickets for

this database

 Passcode Type: There are different passcode types for this tickets database: All Digit,

All Letters, and Mix Digit Letter. Select All Letters or Mix Digit Letter, the sub-item
should be shown-up. Select desired excluding letters for passcode of ticket database.

 Passcode Length : Specify desired passcode length between 8 to 32 for this tickets

database

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

40

 Wireless Information : Specify desired wireless information for this tickets

database(Up to 512 characters)

 Description : Enter appropriate text to denote this database

Billing Type

 Type: There are different billing policies for this tickets database: One Time, Multiple

Times, Volume and Unlimited Until End Time. Select One Time or Multiple Times or
Volume, the Quota sub-item should be shown-up.

 Quota : Enter the time quota for One Time and Multiple Times policy (the maximum

volume allowed is 527040 (366day * 24 * 60)minutes, default is 60 minutes); or enter
the volume quota for Volume policy ( the maximum volume allowed is 102400 MB,
default is 10 MB)

 Effective Starting Time : Specify desired effective starting time for this tickets

database

 Effective Ending Time : Specify desired effective ending time for this tickets

database

Click Save button to create database of ticket.

Pregenerated Tickets Database List

Shows all created ticket of database in the list

 Import Tickets File: Click this to upload the tickets of database. Click “Select File”

button to select the file for the tickets upload. The “Upload File ...” message will appear.
(The format is “*.bin”)

4 Configure Service Domain

41 AirLive WIAS-3200N v2 User’s Manual

 File ID: Denote the identity number of the database.

 Price: Denote the price of ticket in the database.

 Quantity:

 Description : Denote the additional information of database

 Actions: Click an action button to perform the appropriate action.

 Info: Click this option to view information of each tickets database.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

42

Below depicts an example for information of Pregenerated tickets databases when you
click”Info“option

 Edit: Click this option to edit Wireless Information and Description in selected tickets

database.

 Delete: Click this option to delete selected tickets database.

Ticket Information

Show the ticket information in this database.

4 Configure Service Domain

43 AirLive WIAS-3200N v2 User’s Manual

 File ID : Denote the identity number of the database

 Wireless Information : Denote the wireless information on the ticket

 Description : Denote additional information on the ticket

 Effective Starting Time : Denote the effective starting time on the ticket

 Effective Ending Time : Denote the effective ending time on the ticket

 Type and Quota : Denote the billing type and service quota on the ticket

 Passcode Type : Denote the passcode type on the ticket

 Passcode Length : Denote the passcode length on the ticket

 Quantity : Denote the quantity of ticket in this database

 Price : Denote the price charged on the ticket

 Statistic : Show the statistics of information in this database

 Ticket Qty : Denote the quantity of created ticket in this database

 Used Ticket Qty : Denote the quantity of used ticket in this database

 Expired Ticket Qty : Denote the quantity of expired ticket in this database

 Total Price : Denote the total ticket's price and currency in this database

Export Tickets

There are three methods to backup your information of ticket databases

 Export BIN: The administrator can backup ticket database or copy to other AC-920X.

Click Export button, the ticket databases (FileID_passcode.bin) will be download
from system. Below depicts an example for exporting tickets database.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

44

 Export TXT: There are three type of file list: XML, CSV and TXT(only Passcode).

Click Generate button, the passcode list of ticket databases will be download from
system.

 Printable: The selected ticket databases can be previewed on the screen. Click Print

button, the tickets will be shown including the information of Passcode, Price, Start
Time, End Time, and Available SSID on the screen. Admin

Below depicts an example for printable tickets

4 Configure Service Domain

45 AirLive WIAS-3200N v2 User’s Manual

 Tickets List : Show all tickets in this database

 File ID : Denote the identity number of the database

 Code : User can used Passcode of ticket for access Internet

 Type/Quota : Denote the billing type and service quota on this ticket

 Status: Denote the status of ticket. There three types of status : Unused, Used and

Expired

 Create Time : Denote the ticket create time

 Open Time : Denote the time of the first time used on this ticket

 Start Time : Denote effective starting time on this ticket

 End Time : Denote effective ending time on this ticket

 Last Login : Denote the last login time on this ticket

 Price: Denote the price of the charged on this ticket.

 Currency : Denote the currency of the charged on this ticket

 Actions: Click an action button to perform the appropriate action.

 Delete: Click this option to remove ticket from this billing plan. When administrator

clicks this option, the alert message will appear as below.

Click Refresh button to reload the page.

*Note: After you login system via Pregenerated authentication, the timer page will appear.
Don't close Timer page (Because the Logout button on this page)

If Timer Page doesn't appear in the browser, please enter “http(s)://domain0.login” to open
Timer Page

4.2.3 On-Demand

Administrators can enable and configure this authentication method to provide clients
access in a Hotspot environment. Major functions include billing plans creation, accounts
creation, accounts monitoring list, thermal printer support, billing report statistics, and
external payment gateway support. There are three method to generate On-Demand
accounts: Generate by Manual, Print from Thermal Printer, Generate after Online
Payments.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

46

Click on Service Domain > Authentication > On-Demand, then the Billing Plans List
page will appears.

 Status: Denote the current status of billing plan.

 Plan Name: Denote the name of billing plan

 Type/Quota : Denote the billing type and quota of billing plan

 Price: Denote the price charged of billing plan

 Actions: Click an action button to perform the appropriate action.

 Edit: Click this option to edit the respective billing plan. There are 10 billing plans can

be edited.

 Info: Click this option to view accounts list and information of the respective billing

plan.

After configuring billing plans, administrator can create and delete On-Demand users on
this section. Click Info button on Billing Plans List page to enter the On-Demand
Information page. In the On-Demand Information page. Administrator may create and
delete On-Demand users.

4 Configure Service Domain

47 AirLive WIAS-3200N v2 User’s Manual

 Plan Information : Show plan information in this billing plan

 Service : Denote the current status of billing plan

 Plan Name : Denote the plan name of billing plan

 Price : Denote the price charged of billing plan

 Wireless Information : Denote the wireless information of billing plan

 Description : Denote additional information of billing plan

 Type and Quota : Denote billing type and service quota of billing plan

 Effective Starting Time : Denote effective starting time of billing plan

 Effective Ending Time : Denote effective ending time of billing plan

Click Preview button to preview ticket in the billing plan. Below depicts an example for
previewing ticket. Click Close button to close window.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

48

Click Add Accounts button, the create page will appear as below. Click Cancel button to
close window.

Click Create button to add new account for this billing plan. Below depicts an example for
creating ticket.

4 Configure Service Domain

49 AirLive WIAS-3200N v2 User’s Manual

 Statistic : Show on-demand users statistic information for this billing plan

 Ticket Qty : Denote the quantity of created ticket of billing plan

 Used Ticket Qty : Denote the quantity of used ticket of billing plan

 Expired Ticket Qty : Denote the quantity of expired ticket of billing plan

 Total Price : Denote the total ticket's price and currency of billing plan

 Tickets per day : Show the bar chart of quantity of the ticket in this billing plan

 Tickets List :

 Plan : Denote the billing plan on this ticket

 Code : User can used Passcode of ticket for access Internet

 Type/Quota : Denote the billing type and service quota on this ticket

 Status: Denote the current status on this ticket. There three types of status : Unused,

Used and Expired

 Create Time : Denote the time of create on this ticket

 Open Time : Denote the time of the first time used on this ticket

 Start Time : Denote effective starting time on this ticket

 End Time : Denote effective ending time on this ticket

 Last Login : Denote the last login time on this ticket

 Price : Denote the price of the charged on this ticket

 Currency : Denote the currency of the charged on this ticket

 Actions: Click an action button to perform the appropriate action.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

50

 Delete: Click this option to remove ticket from this billing plan. When administrator

clicks this option, the alert message will appear as below.

Click Refresh button to renew this page.

*Note: The list only shows generate of the ticket by clicking Add Account button.

*Note: After you login system via On-Demand authentication, the timer page will appear.

Don't close Timer page (Because the Logout button on this page)

If Timer Page doesn't appear in the browser, please enter “http(s)://domain0.login ” to open
Timer Page.

4.2.3.1 Billing Plan Setup

Click on Service Domain > Authentication > On-Demand，and click Edit option on
Billing Plans List, the Billing Plan Setup page will appear.

4 Configure Service Domain

51 AirLive WIAS-3200N v2 User’s Manual

Billing Plan0 Setup

 Service: By default, it's “Disable”. To “Enable” to activate this billing plan.

 Plan Name: Enter plan name for this billing plan.

 Price: The price charged and currency for this billing plan.

* Note: The Paypal payment gateway does not support “Customize Currency” option.

 Passcode Type: There are different passcode types for this billing plan: All Digit, All

Letters, Mix Digit Letter. Select All Letters or Mix Digit Letter, the sub-item should be

shown-up. Select desired excluding letters for passcode of ticket databases.

 Passcode Length: Specify desired passcode length between 8 to 32 for this billing

plan.

 Wireless Information: Enter the wireless information for this billing plan.

 Description: Enter any additional information that will appear at the bottom of the

receipt.

 Paypal Description: Enter any additional information that will appear at the list of the

login page.

 Receipt Header: Enter header information that will appear at the top of the receipt.

 Receipt Footer: Enter footer information that will appear at the bottom of the receipt.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

52

Billing Type

 Billing Type: There are different policies for this billing plan: One Time, Multiple

Times, Volume and Unlimited Until End Time. Select One Time or Multiple Times or
Volume, the Quota sub-item should be shown-up.

 Quota : Enter the time quota for One Time and Multiple Times policy (the maximum

volume allowed is 527040 minutes, default is 60 minutes); or enter the volume quota
for Volume policy ( the maximum volume allowed is 102400 MB, default is 10 MB)

 Effective Starting Time: Specify desired effective starting time for this billing plan.

 Effective Ending Time: Specify desired effective ending time for this billing plan.

Display Item Option

Select desired display item for ticket

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes.

4 Configure Service Domain

53 AirLive WIAS-3200N v2 User’s Manual

4.2.3.2 Payment Gateway

This section is for merchants to set up an external payment gateway to accept payments in
order to provide access service to end customers who wish to pay for the service on-line.

Select Paypal to enable External Payment Gateway. Before setting up “PayPal”, it is
required that the merchant owners have a valid PayPal “API Username”, “API Password”.

Please see Appendix D – Accepting Payments via PayPal, Appendix E – Examples of
Making Payments for End Users for more information about setting up a PayPal
Business Account, relevant maintenance functions, and example for end users.

*Note: The Paypal payment gateway does not support “Customize Currency” option on
Billing Plan.

After opening a PayPal Business Account, the merchant should find the “API Signature” of
this PayPal account to continue “External Payment Gateway Setup”.

 API Username: This is the “Login ID”(E-mail address) that is associated with the

PayPal Business Account.

 API Password: This is the “Login Password” that is associated with the PayPal

Business Account.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

54

 API Signature: This the key used by Paypal to validate all the transactions.

 Invoice Number: An invoice number may be provided as additional information

against a transaction.

 Current No. : Show current invoice number.

 Billing Plan Setup List :

 Enable: Select specified the billing plan for this payment gateway.

 Plan Name : Denote the name of billing plan

 Type/Quota : Denote the billing type and quota of billing plan

 Price : Denote the price charged of billing plan

 Information: Click this button to view accounts information for PayPal.

Payment Gateway Information

Show current ticket's invoice number.

Click Edit button to enter Payment Gateway Setup page.

 Statistic : Shows on-demand users statistic information for this billing plan via

payment gateway created

 Ticket Qty : Denote quantity of created ticket from payment gateway

 Used Ticket Qty : Denote quantity of used ticket from payment gateway

 Expired Ticket Qty : Denote quantity of expired ticket from payment gateway

 Total Price : Denote total ticket's price and currency from payment gateway

 Tickets per day : Show the bar chart of quantity of the ticket from payment gateway

4 Configure Service Domain

55 AirLive WIAS-3200N v2 User’s Manual

 Tickets List : Show tickets information

 Plan : Denote the billing plan on this ticket

 Code : User can used Passcode of ticket for access Internet

 Type/Quota : Denote the billing type and service quota on this ticket

 Status: Denote the current status on this ticket. There three types of status : Unused,

Used and Expired

 Create Time : Denote the time of create on this ticket

 Open Time: Denote the time of the first time used on this ticket

 Start Time : Denote effective starting time on this ticket

 End Time : Denote effective ending time on this ticket

 Last Login : Denote the last login time on this ticket

 Price: Denote the price of the charged on this ticket.

 Currency : Denote the currency of the charged on this ticket

 Actions: Click an action button to perform the appropriate action.

 Delete: Click this option to remove ticket from this billing plan. When administrator

clicks this option, the alert message will appear as below.

Click Refresh button to renew this page.

*Note: On this List, it only shows all of generated tickets through External Payment
Gateway.

*Note: After you login system via On-Demand authentication, the timer page will appear.

Don't close Timer page (Because the Logout button on this page)

If Timer Page doesn't appear in the browser, please enter “http(s)://domain0.login” to open
Timer Page.

*Note: If administrator wants to refund transaction, please see Appendix E. Issue

Refund for PayPal

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

56

4.2.3.3 Thermal Printer Setup

WIAS-3200N v2 can generate ticket of On-Demand users manually or automatically from
Thermal Printer. Please click on Service Domain → Authentication → On-Demand →
Thermal Printer Setup to enter the Thermal Printer List page.

In the Thermal Printer List page, administrator may configure Thermal Printer setting and
generate tickets manually and delete tickets.

*Note: If administrator wants to generate tickets from Thermal Printer, system must use
DS-100 v2 to control Thermal Printer.

 Status : Denote the current status of thermal printer

 IP Address : Denote the IP address of f DS-100 v2 device server

 Command Port : Denote the command port of f DS-100 v2 device server

 COM Port : Denote the COM port of f DS-100 v2 device server to connect to thermal

printer

 Date : Denote balance date of thermal printer

 Description : Denote the additional information of thermal printer

 Actions: Click an action button to perform the appropriate action.

 Edit: Click this option to edit the respective settings of thermal printer. There are 10

thermal printer can be edited. Each thermal printer can specified billing plan

 Info : Click this option to view accounts list and information of the respective billing

plan from thermal printer created

4 Configure Service Domain

57 AirLive WIAS-3200N v2 User’s Manual

Click Edit button to enter Thermal Printer Setup page. In the Thermal Printer Setup page,
administrator may configure related settings.

Thermal Printer Setup

 Service: By default, it's “Disable”. To “Enable” to activate this function.

 IP Address : Enter the IP address of WIAS-3200N v2 serial server

 Command Port : Enter the command port of WIAS-3200N v2 serial server

 COM Port : Select the COM port of WIAS-3200N v2 serial server to connect to

thermal printer

 Balance Date: Enter balance date for statement printing from thermal printer. Thermal

printer can print “Current Balance” or “Early Balance” statement. Below depicts an
example for balance date.

 Description : Enter appropriate text to denote this thermal printer

 Billing Plan Setup List :

 Enable : Select specified the billing plan for this thermal printer

 Plan Name : Denote the name of billing plan

 Type/Quota : Denote the billing type and quota of billing plan

 Price : Denote the price charged of billing plan

Balance Date

Current Date

Early Balance

Current Balance

6/17 23:59 6/18 20:00

6/17 00:00

6/17 23:59

6/18 00:00

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

58

 Information: Click this button to view accounts information for PayPal.

*Note: After configuring thermal printer general setting, administrator must select specified

billing plan for this thermal printer.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

Click Info button to enter Thermal Printer Information page. In the Thermal Printer
Information page, administrator may generated and delete ticket manually.

 Thermal Printer Information: Show setting information in this thermal printer.

 Status : Denote the current status of thermal printer

 IP Address : Denote the IP address of DS-100 v2 device server

 Command Port : Denote the command port of f DS-100 v2 device server

 COM Port : Denote the COM port of f DS-100 v2 device server to connect to thermal

printer

 Date : Denote balance date of thermal printer

 Description : Denote the additional information of thermal printer

Click Edit button to enter Thermal Printer Setup page.

4 Configure Service Domain

59 AirLive WIAS-3200N v2 User’s Manual

 Statistic : Shows on-demand users statistic information for this billing plan via thermal

printer created

 Ticket Qty : Denote the quantity of created ticket from thermal printer

 Used Ticket Qty : Denote the quantity of used ticket from thermal printer

 Expired Ticket Qty : Denote the quantity of expired ticket from thermal printer

 Total Price : Denote the total ticket's price and currency from thermal printer

 Tickets per day : Show the bar chart of quantity of the ticket from thermal printer

 Tickets List : Show tickets information

 Plan : Denote the billing plan on this ticket

 Code: User can use Passcode of ticket for access Internet. Clicking hyperlinks to view

this ticket information as below. Click Print button, the ticket will print from thermal
printer again.

 Type/Quota : Denote the billing type and service quota on this ticket

 Status: Denote the current status on this ticket. There three types of status : Unused,

Used and Expired

 Create Time : Denote the time of create on this ticket

 Open Time : Denote the time of the first time used on this ticket

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

60

 Start Time : Denote the effective starting time on this ticket

 End Time : Denote the effective ending time on this ticket

 Last Login : Denote the last login time on this ticket

 Price: Denote the price of the charged on this ticket.

 Currency : Denote the currency of the charged on this ticket

 Actions: Click an action button to perform the appropriate action.

 Delete: This will delete the ticket individually. When administrator click Delete

Button, the alert message will appear as below.

Click Refresh button to renew this page.

*Note: On this List, it only shows all of generated tickets from Thermal Printer.

*Note: After you login system via On-Demand authentication, the timer page will appear.

Don't close Timer page (Because the Logout button on this page)

If Timer Page doesn't appear in the browser, please enter “http(s)://domain0.login” to open
Timer Page.

4.2.3.4 Billing Plan Report

Click on Service Domain > Authentication > On-Demand to enter the Billing Plans
Report page. Administrator can get a complete report or a report of a particular period.

4 Configure Service Domain

61 AirLive WIAS-3200N v2 User’s Manual

Search Create Time Range

 On-Demand Type: There are four type can be selected: ALL, Manually Create,

Payment Gateway and Thermal Printer.

 Start Time : Specify desired search starting time

 End Time : Specify desired search ending time

 Search Result: Select a time period to get a period report. The report tells the total

income and individual accounting of each plan for all plans available for that period of
time.

.

Search Result

Shows search result of the specified time range

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

62

 Search Time: Denote the specified search time range.

 Name: Denote the name of billing plan.

 On-Demand: Denote the quantity of ticket from manually created.

 Payment Gateway: Denote the quantity of ticket from payment gateway created.

 Thermal Printer: Denote the quantity of ticket from thermal printer created.

 Amount Qty: Denote total quantity of created ticket of billing plan.

 Unit Price: Denote the unit price of billing plan.

 Subtotal: Denote the total price of billing plan.

 Total: Denote the total price and quantity on all billing plan.

4.2.3.5 Ticket Customization

Click on Service Domain > Authentication > On-Demand to enter the Ticket
Customization page. Administrator can edit text on printed ticket on this page.

Change these settings as described here and click Save button to save your changes.
Click Preview button to preview ticket in the Billing Plan 0. Below depicts an example for
previewing ticket. Click Close button to close window.

4 Configure Service Domain

63 AirLive WIAS-3200N v2 User’s Manual

Click Reboot button to activate your changes

4.3.3 Local RADIUS Accounts

WIAS-3200N v2 provide Local RADIUS server authentication. Please click on Service
Domain > Authentication > Remote RADIUS Server, the page of Remote RADIUS
Server Setup will appear. Administrator can add accounts by manual or import accounts

file.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

64

 Group Setup: Enter the specified name on group and click Add button to create. Up

to 20 groups can add. (You can set 4-16 alphanumeric and ~!@#$%^*()_+-:{}

|:<>?[]/,’.= specific characters)

 Group List: Display all of groups in the list, click Delete option to remove group name

and all of the accounts in this group will be removed, click Edit option to change group
name.

 RADIUS Accounts Setup :

 Username/Password: Enter the username and password of account on local

RADIUS authentication.(You can set 4-16 alphanumeric and ~!@#$%^*()_+-:

{}|:<>?[]/;’..= specific characters)

 MAC Address: Enter the MAC address of account on local RADIUS authentication.

(Optional)

 Description: Enter appropriate text to denote this account.

 Group: Select the specified group on local RADIUS authentication, default is None.

Click Save button to add new account, all of accounts can be edited (Username cannot
edit) and deleted.

Local RADIUS Accounts List

 Delete: Select the specified group and click Delete button to remove accounts of the

specified group.

4 Configure Service Domain

65 AirLive WIAS-3200N v2 User’s Manual

 Import Accounts File: Select the specified group on Group option and click Select

File button to select the text file for uploading the accounts of the specified group. The
the “Upload File ...” message will appear.

The upload file should be a text file and the format of each line is “Username, Password,
MAC, Description” without the quotes. There must be no spaces between the fields and
commas. The MAC field could be omitted but the trailing comma must be retained. When
adding accounts by uploading a file, the existing accounts in the embedded database,
uploading process will fail. Below depicts an example for text file.

*Note: The same Username account can't exist on different groups, the Group option only
for convenient management.

 Export Accounts File: Select the specified group on Group option and click Export

button to save accounts of the specified group to PC. The “File Download” window will
appear.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

66

 Search: Enter a keyword to be searched in the text field and all matching the

keyword will be listed.

 Username : Denote the username of account on local RADIUS authentication

 MAC Address : Denote the MAC address of account on local RADIUS authentication

 Description : Enter appropriate text to denote this account

 Group : Denote the specified of account on local RADIUS authentication

 Actions: Click an action button to perform the appropriate action.

 Delete: Click this option to remove the specified account.

 Edit : Click this option to edit the specified account

*Note: These settings will become effective immediately after clicking the Save button.

4 Configure Service Domain

67 AirLive WIAS-3200N v2 User’s Manual

4.3.4 Remote RADIUS Accounts

WIAS-3200N v2 provide remote RADIUS server authentication. Please click on Service
Domain > Authentication > Remote RADIUS Server, the page of Remote RADIUS
Server Setup will appear

 Service: By default, it's “Disable”. To “Enable” to activate this function.

 Primary/Secondary Server IP: Enter the IP address of the Authentication RADIUS

server.

 Authentication Port: The port number used by Authentication RADIUS server. Use

the default 1812 or enter port number specified.

 Accounting Port: The port number used by Accounting RADIUS server. Use the

default 1813 or enter port number specified.

 Secret Key: The secret key for system to communicate with RADIUS server. Support

1 to 64 characters.

 Accounting Service: Select this to enable or disable the “Accounting Service” for

accounting capabilities.

 Authentication Type: Select the desired authentication type from the drop-down list;

the options are CHAP and PAP.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

68

4.3.5 Clear Tickets

 Ticket Type: There are four ticket types for you to select: Pregenerated Ticket,

On-Demand Ticket, Payment Gateway, and Thermal Printer.

 File ID: Select File ID.

 Ticket Status: Select Expired or Use up.

 Search: Click “Search” button to search the ticket which selected.

 Delete: Click “Delete” button to delete the ticket which selected.

4.4 Privilege IP/MAC Address

This function provides local device can access Internet without authentication. If there are
some workstations belonging WIAS-3200N v2 that need to access to network without
authentication, enter the IP or MAC address of these workstations in this list. Up to 20
addresses can be defined in this list. Please click on Service Domain > Privilege IP/MAC

Address, the page of Privilege IP/MAC Address Setup will appear.

Privilege IP/MAC Address Setup

 Device Name: Enter the name of the workstation, 4-32 characters.

4 Configure Service Domain

69 AirLive WIAS-3200N v2 User’s Manual

 IP Address: Enter the IP address (or IP address/Mask) of the workstation. Permitting

specific IP addresses to have network access rights without going through standard
authentication process

 MAC Address: Enter the MAC address of the workstation. Permitting specific MAC

addresses to have network access rights without going through standard
authentication process

 Description: Enter appropriate text to denote this workstation, up to 64 characters.

Click Save button to add new rule, all of rules can be edited and deleted

Privilege IP/MAC Address List

 Device Name: Denote the name of workstation.

 IP Address : Denote the IP address(or IP address/Mask) of workstation

 MAC Address: Denote the MAC address of workstation.

 Description: Enter appropriate text to denote this workstation.

 Actions: Click an action button to perform the appropriate action.

 Delete : Click this option to remove the specified item

 Edit : Click this option to edit the specified item

4.5 Walled Garden

This function provides certain free services or advertisement web pages for users to
access the websites listed before login and authentication. Up to 20 address or domain
names of the websites can be defined in this list. User without the network access right can
still have a chance to experience the actual network service free of charge. Please click on
Service Domain > Walled Garden, the page of Walled Garden Setup will appear.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

70

Walled Garden

 Name : Enter a descriptive name for this rule for identifying purposes

 IP Address/Domain: Enter the IP address/Domain of the workstation.

 Homepages: Enter the MAC address of the workstation.

 Description : Enter appropriate text to denote this workstation

Click Save button to add new rule, all of rules can be edited and deleted

Walled Garden List

 Name : Denote the name of workstation

 IP Address/Domain : Denote the IP address(or IP address/Mask) of workstation

 Actions: Click an action button to perform the appropriate action.

 Delete : Click this option to remove the specified item

 Edit : Click this option to edit the specified item

After add website on the list, the Walled Name will appear on Login page. Below depicts
an example for Walled Garden

4 Configure Service Domain

71 AirLive WIAS-3200N v2 User’s Manual

4.6 Blacklist

The administrator can add, delete and edit blacklist for uses access. If the system wants to
deny uses access to specified website, enter the IP address, URL or Keyword of these
websites in this list. Up to 20 rules can be defined in this list. Please click on Service

Domain →

Blacklist, the page of Blacklist Setup will appear.

Blacklist Setup

 Name : Enter a descriptive name for this rule for identifying purposes

 IP Address/URL: Enter the specified IP address/URL of the website or Keyword of the

website. Rejecting specific website to access rights

 Description: Enter appropriate text to denote this website.

Click Save button to add new rule, all of rules can be edited and deleted

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

72

Blacklist

 Name: Denote the name of rule

 URL: Denote the IP address/URL or Keyword of the website

 Actions: Click an action button to perform the appropriate action.

 Delete: Click this option to remove the specified item

 Edit: Click this option to edit the specified item

4.7 Notification

WIAS-3200N v2 can automatically send the notification of Traffic Log, On-Demand Log,
Session Log and Billing Report to 3 particular E-mail addresses. A trial email is provided
by the system for validation. Please click on Service Domain > Notification, the page of
Notification E-mail Setup will appear.

SMTP Server Setup

4 Configure Service Domain

73 AirLive WIAS-3200N v2 User’s Manual

 Enabled: Click Enabled to activated SMTP Server

 Sender From: The E-mail address of the administrator in charge of monitoring. This

will show up as the sender's E-mail.

 SMTP Server: The IP address / Domain of the sender's SMTP server.

 Port: The port of the sender's SMTP server. (Default is 25)

*Note: Sometimes SMTP server use Port 587 for TLS encryption and Port 465 for SSL
encryption

 Encryption: Some SMTP server needs encryption linking for sending E-mail. The

system provides encryption for sender's SMTP server

 SMTP Auth: Some SMTP server needs authentication username and password for

sending E-mail. The system provides authentication for sender's SMTP server

 Username: The sender's authentication username for STMP server

 Password: The sender's authentication password for STMP server

Notification E-mail Setup

 Receiver E-mail Address (es): Up to 3 E-mail address can be set up to receive the

notification. These are the receiver's E-mail address.

 Sending Interval: The time interval (in minute) to send the E-mail report. (Default is

1440 minutes; the range is between 10 to 4200 minutes)

 Billing Report Time: The start time of sending e-mail. For example: the Billing Report

Time is 14:00 and Sending Interval is 6 hours, the system will send report on 20:00.

 SMTP Sending Test: Click Send button to verify Notification E-mail settings. Below

depicts an example for success sending test.

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

74

Syslog Setup

There are 3 types of Syslog supported: Syslog Log, On-Demand User Log and Session
Log. Enter the specify IP address and Port number to sent report.

*Note: The all history log are saved in the DRAM, if you restart system, the all of history log

will empty.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes.

If the history E-mail has been entered above Notification settings, after Sending Interval,
the system will send History E-mail to receiver's E-mail address automatically.

4 Configure Service Domain

75 AirLive WIAS-3200N v2 User’s Manual

Traffic Log

As shown in the following figure, each line is traffic history record consisting of 10 fields :

Date, Auth Type, Status, Passcode/Username, IP, MAC, Packets In, Bytes In, Packets
Out and Bytes Out.

 Date : Denote the current event's date and time

 Auth Type: There will shows 6 types of authentication: Pregenerated, On-Demand,

Local Users (Local RADIUS Users), Remote RADIUS, LDAP and Guest.

 Status : There will show 10 types of status as below :

 LOGIN : Denote the user login to the hotspot service

 LOGOUT : Denote the user logout to the hotspot service

 IDLE TIMEOUT : Denote the user idle time is over timeout setting of Service Domain,

the system will logout user automatically

 USE UP : Denote the quota of time of user is over

 SESSION TIMEOUT : Denote the user session timeout for connecting to remote

RAIDUS

 VOLUME USE UP : Denote the quota of volume of user is over

 KICK: Denote the system kick out the user.

 TIME OUT OF RANGE : Denote the service time out of range

 Passcode/Username : Denote the user's passcode or username

 IP : Denote the user's IP address

 MAC : Denote the user's MAC address

 Packets In : Denote the current user's packets in

 Bytes In : Denote the current user's bytes in

 Packet Out : Denote the current user's packets out

 Bytes Out : Denote the current user's bytes out

On-Demand Log

As shown in the following figure, each line is traffic history record consisting of 15 fields :

Date, Location, Status, Passcode/Username, IP, MAC, Packets In, Bytes In, Packets
Out, Bytes Out, Start Time, End Time, Plan, Payment Type and Cost

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

76

 Date : Denote the current event's date and time

 Location : Denote the current device's location

 Status : There will show 10 types of status as below :

 LOGIN : Denote the user login to the hotspot service

 LOGOUT : Denote the user logout to the hotspot service

 IDLE TIMEOUT : Denote the user idle time is over timeout setting of Service Domain,

the system will logout user automatically

 USE UP : Denote the quota of time of user is over

 VOLUME USE UP : Denote the quota of volume of user is over

 KICK : Denote the system kick out the user

 TIME OUT OF RANGE : Denote the service time out of range

 ADD OD ACCOUNT : Denote the system add On-Demand user account

 DELETE OD ACCOUNT : Denote the system delete On-Demand user account

 Passcode/Username : Denote the user's passcode or username

 IP : Denote the user's IP address

 MAC : Denote the user's MAC address

 Packets In : Denote the current user's packets in

 Bytes In : Denote the current user's bytes in

 Packet Out : Denote the current user's packets out

 Bytes Out : Denote the current user's bytes out

 Start Time : Denote the start time on this users

 End Time : Denote the end time on this users

 Plan : Denote the current user's billing plan

 Payment Type : Denote the current payment type, there were show Cash or PayPal

 Cost : Denote the current service charge

4 Configure Service Domain

77 AirLive WIAS-3200N v2 User’s Manual

 Session Log: The system can recorded connection details of each user accessing

the Internet and sent out to a specified Syslog Server or E-Mail based on defined
interval time. As shown in the following figure, each line is traffic history record
consisting of 10 fields, Date, Time, Session Type, Username, Service Domain,

Source IP, Source Port, Destination IP, Destination Port, and MAC.

Billing Report

The system can record the billing report and sent out to a specified E-Mail based on
defined Billing Report Time. As shown in the following figure.

4.8 Online Users

The administrator can view status of all online users on each Service Domain. Please click
on Service Domain > Online Users, the page of Online Users will appear. Below depicts
an example for Online User Information. There provided information of Passocde, IP
Address, MAC Address, Login Time, Packets In/Out and Bytes In/Out.

 A

uth Type : Denote the current user's authentication type

 Passcode/Username : Denote the current user's passcode or username

 IP Address : Denote the current user's IP addre

ss

4 Configure Service Domain

AirLive WIAS-3200N v2 User’s Manual

78

 MAC Address : Denote the current user's MAC address

 Login Time : Denote the login time on this user

 Packets In/Out : Denote the current user's packets in and out

 Bytes In/Out : Denote the current user's bytes in and out

 Actions: Click Logout option to logout online users

C

lick Refresh button to reload the page

4.9 Log Info

The WIAS-3200N v2 can record authentication traffic history and the system will
automatically send out the history information via notification service (See Notification
page). The history of each day will be saved separately in the DRAM for 3 days and sorted
by time, the traffic provides all login and logout activity of specific date. Other information
includes Passocde/Username, IP Address, MAC Address, Packets In/Out and Bytes In/Out.
Please click on Service Domain > Traffic Info, the page of Log Info will appear.

*Note: The all history log are saved in the DRAM, if you need restart system and also keep
the history, please manually copy and save the information before restarting.

Traffic Log

As shown in the following figure, each line is traffic history record consisting of 10 fields :

Date, Auth Type, Status, Passcode/Username, IP, MAC, Packets In, Bytes In, Packets
Out and Bytes Out.

 Date : Denote current event's date and time

4 Configure Service Domain

79 AirLive WIAS-3200N v2 User’s Manual

 Auth Type: There will shows 6 types of authentication: Pregenerated, On-Demand,

Local Users (Local RADIUS Users), Remote RADIUS, LDAP and Guest.

 Status : There will show 10 types of status as below :

 Passcode/Username: Denote the user's passcode or username.

 IP : Denote the user's IP address

 MAC : Denote the user's MAC address

 Packets In: Denote the current user's packets in.

 Bytes In: Denote the current user's bytes in.

 Packet Out: Denote the current user's packets out.

 Bytes Out: Denote the current user's bytes out.

On-Demand Log

As shown in the following figure, each line is traffic history record consisting of 14 fields :

Date, Status, Passcode/Username, IP, MAC, Packets In/Out, Bytes In/Out, Start Time,
End Time, Plan, Payment Type and Cost.

 Date : Denote current event's date and time

 Status : There will show 10 types of status as below :

 Passcode/Username: Denote the user's passcode or username.

 IP : Denote the user's IP address

 MAC : Denote the user's MAC address

 Packets In: Denote the current user's packets in.

 Bytes In: Denote the current user's bytes in.

 Packet Out: Denote the current user's packets out.

 Bytes Out: Denote the current user's bytes out.

 Start Time : Denote the start time of current service users

 End Time : Denote the end time of current service users

 Plan: Denote the current user's billing plan.

 Payment Type : Denote the current payment type, there were show Cash or PayPal

 Cost : Denote the current service charge

Click Refresh button to reload the page.

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

80

5

5. Configure Wireless

Connection

5.1 General Setups

The administrator can change the data transmission, channel and output power settings for
the system. Please click on Wireless > General Setup and follow the below setting.

 MAC address: The MAC address of the Wireless interface is displayed here.

 Band Mode: Select an appropriate wireless band; bands available are 801.11b,

802.11b/g, 802.11b/g/n and 802.11n.

 Transmit Rate Control: Select the desired rate from the drop-down list; the options

are auto or ranging from 1Mbps to 54Mbps for 802.11b/g modes, or 1Mbps to 11Mbps
for 802.11b mode.

 Country: Select the desired country code from the drop-down list; the options are US,

ETSI and Japan.

 Channel: The channel range will be changed by selecting different country code. The

channel range from 1 to 11 for US country code, or 1 to 13 for ETSI country code, or 1
to 14 for Japan (Channel 14 only for 802.11b Rate).

 Auto Scan: Click this button, the channel will be changed to suitable channel.

 AP List: Click this button, the system will show current all AP list. Click Rescan button

to rescan list, click Close button to close window

5 Configure Wireless Connection

81 AirLive WIAS-3200N v2 User’s Manual

 Tx Power: You can adjust the output power of the system to get the appropriate

coverage for your wireless network. Select LEVEL 1 to LEVEL 7 needed for your
environment. If you are not sure of which setting to choose, then keep the default
setting, LEVEL 7.

 When Band Mode select in 802.11b/g/n or 802.11n, the HT Physical Mode settings

should be show immediately.

 Tx/Rx Stream: By default, it's 2.

 Channel Bandwidth: The "20/40” MHz option is usually best. The other option is

available for special circumstances.

 Extension Channel: Only for Channel Bandwidth “40” MHz Select the desired

channel bonding for control.

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

82

 MCS: This parameter represents transmission rate. By default (Auto) the fastest

possible transmission rate will be selected. You have the option of selecting the speed
if necessary.

 Shout GI: Short Guard Interval, by default, it's “Enable”. It can increase throughput.

However, it can also increase error rate in some installations, due to increased
sensitivity to radio-frequency reflections. Select the option that works best for your
installation.

 Aggregation: By default, it's “Enable”. To “Disable” to deactivated Aggregation. A part

of the 802.11n standard (or draft-standard). It allows sending multiple frames per
single access to the medium by combining frames together into one larger frame. It
creates the larger frame by combining smaller frames with the same physical source
and destination end points and traffic class (i.e. QoS) into one large frame with a
common MAC header.

 Aggregation Frames: The Aggregation Frames is in the range of 2~64, default is 32.

It determines the number of frames combined on the new larger frame.

 Aggregation Size: The Aggregation Size is in the range of 1024~65535, default is

50000. It determines the size (in Bytes) of the larger frame.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes. The item in this page is for AP's RF general
settings and will be applied to all VAPs and WDS Link.

5.2 Advanced Setup

The administrator can change the Slot Time, ACK Timeout, and RTS threshold and
fragmentation threshold settings for the system. Please click on Wireless > Advanced
Setup and follow the below setting.

5 Configure Wireless Connection

83 AirLive WIAS-3200N v2 User’s Manual

 Slot Time: Slot time is in the range of 9~1489 and set in unit of microsecond. The

default value is 9 microsecond. Slot time is the amount of time a device waits after a
collision before retransmitting a packet. Reducing the slot time decreases the overall
back-off, which increases throughput. Back-off, which is a multiple of the slot time, is
the random length of time a station waits before sending a packet on the LAN. For a
sender and receiver own right of the channel the shorter slot time help manage shorter
wait time to re-transmit from collision because of hidden wireless clients or other
causes. When collision sources can be removed sooner and other senders attempting
to send are listening the channel (CSMA/CA) the owner of the channel should
continue ownership and finish their transmission and release the channel. Then,
following ownership of the channel will be sooner for the new pair due to shorter slot
time. However, when long duration of existing collision sources and shorter slot time
exist the owners might experience subsequent collisions. When adjustment to longer
slot time can’t improve performance then RTS/CTS could supplement and help
improve performance.

 ACK Timeout: ACK timeout is in the range of 1~372 and set in unit of microsecond.

The default value is 64 microsecond. All data transmission in 802.11b/g request an
“Acknowledgement” (ACK) send by receiving radio. The transmitter will resend the
original packet if correspondent ACK failed to arrive within specific time interval, also
refer to as “ACK Timeout”.

ACK Timeout is adjustable due to the fact that distance between two radio links may
vary in different deployment. ACK Timeout makes significant influence in performance
of long distance radio link. If ACK Timeout is set too short, transmitter will start to
“Resend” packet before ACK is received, and throughput become low due to
excessively high re-transmission.

ACK Timeout is best determined by distance between the radios, data rate of average
environment. The Timeout value is calculated based on round-trip time of packet with
a little tolerance, so, if experiencing re-transmissions or poor performance the ACK
Timeout could be made longer to accommodate.

*Note: Slot Time and ACK Timeout settings are for long distance links. It is important
to tweak settings to achieve the optimal result based on requirement.

 RSSI Threshold: RSSI (Received Signal Strength Indication) Threshold is in the

range of -127 ~ 128. The default value is 24. RSSI Threshold can be used to control
the level of noise received by the device.

 Beacon Interval: Beacon Interval is in the range of 40~3500 and set in unit of

millisecond. The default value is 100 msec.

Access Point (AP) in IEEE 802.11 will send out a special approximated 50-byte frame,
called “Beacon”. Beacon is broadcast to all the stations, provides the basic information
of AP such as SSID, channel, encryption keys, signal strength, time stamp, support
data rate.

All the radio stations received beacon recognizes the existence of such AP, and may
proceed next actions if the information from AP matches the requirement. Beacon is
sent on a periodic basis, the time interval can be adjusted.

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

84

By increasing the beacon interval, you can reduce the number of beacons and
associated overhead, but that will likely delay the association and roaming process
because stations scanning for available access points may miss the beacons. You can
decrease the beacon interval, which increases the rate of beacons. This will make the
association and roaming process very responsive; however, the network will incur
additional overhead and throughput will go down.

 DTIM Interval: The DTIM interval is in the range of 1~255. The default is 1.

DTIM is defined as Delivery Traffic Indication Message. It is used to notify the wireless
stations, which support power saving mode, when to wake up to receive multicast
frame. DTIM is necessary and critical in wireless environment as a mechanism to fulfill
power-saving synchronization.

A DTIM interval is a count of the number of beacon frames that must occur before the
access point sends the buffered multicast frames. For instance, if DTIM Interval is
set to 3, then the Wi-Fi clients will expect to receive a multicast frame after receiving
three Beacon frame. The higher DTIM interval will help power saving and possibly
decrease wireless throughput in multicast applications.

 Fragment Threshold: The Fragment Threshold is in the range of 256~2346 byte. The

default is 2346 byte.

Each Wi-Fi packet can be divided into smaller packets, marked with a sequential
fragment number and re-assemble in the receiving ends. The purpose is to make a
short frame, instead of long frame, transmitting by radio in a heavy noisy environment.
Because of sending smaller frames, corruptions are much less likely to occur. The
pros is obvious, the cons is the overhead for transmission. So, in a clean environment,
higher fragment threshold can be an option to increase throughput.

Fragmentation will be triggered by setting the Fragment Threshold, usually in
Byte-length. Only when the frame size is over the Threshold, fragmentation will take
place automatically.

 RTS Threshold: TRTS Threshold is in the range of 1~2347 byte. The default is 2347

byte.

The main purpose of enabling RTS by changing RTS threshold is to reduce possible
collisions due to hidden wireless clients. RTS in AP will be enabled automatically if the
packet size is larger than the Threshold value. By default, RTS is disabled in a normal
environment supports non-jumbo frames.

 Short Preamble: By default, it’s “Enable”. To Disable is to use Long 128-bit Preamble

Synchronization field.

 The preamble is used to signal "here is a train of data coming" to the receiver. The

short preamble provides 72-bit Synchronization field to improve WLAN transmission
efficiency with less overhead.

 Tx Burst: By default, it’s “Enable”. To Disable is to deactivate Tx Burst.

With TX burst enabled, AP will send many packets in a burst, without collision
detection and RTS/CTS for each packet. TX Burst have better throughput but cause
interference with other APs in channel.

5 Configure Wireless Connection

85 AirLive WIAS-3200N v2 User’s Manual

 802.11g Protection: Click Enable button to activate 802.11g Protection Mode, and

Disable to inactivate 802.11g Protection Mode.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes. The items in this page are for AP's RF
general settings and will be applied to all VAPs and WDS Link.

5.3 Virtual AP Setup

The WIAS-3200N v2 support broadcasting multiple SSIDs, allowing the creation of Virtual
Access Points, partitioning a single physical access point into 8 logical access points, each
of which can have a different set of security, VLAN Tag(ID) and network settings. If wireless
client connect to wire area network with VLAN Tag (ID), the administrator can use dump
switch or VLAN switch on wired area network, below picture shows multiple SSIDs with
different VLAN settings use dump switch connect to wired area. It also shows multiple
SSIDs with different VLAN settings use VLAN switch connect to wired area.

Multiple SSIDs with different VLAN settings use dump switch connect to wired area.

Multiple SSIDs with different VLAN settings use VLAN switch connect to wire area.

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

86

The administrator can create Virtual AP via this page. Please click on Wireless > Virtual
AP Setup and follow the below setting.

 VAP: Indicate the system's Virtual AP.MAC Address: The MAC address of the VAP

Interface is displayed here. When you enable AP and reboot system, the MAC
address will display here.

 ESSID: Indicate the ESSID of the respective Virtual AP

 Status: Indicate the current Status of the respective Virtual AP. The VAP0 always on.

 Security Type: Indicate a used security type of the respective Virtual AP.

 MAC Filter: Indicate a used MAC filter of the respective Virtual AP. Click this option to

configure MAC Filter of the respective Virtual AP.

 Edit: Click this option to configure Virtual AP's settings

5.3.1 VAP0-3 Setup

For each Virtual AP, administrators can configure general settings and security type.

Click Wireless > Virtual AP, click “Edit” of Virtual AP List and then Virtual AP
Configuration page appears.

5 Configure Wireless Connection

87 AirLive WIAS-3200N v2 User’s Manual

5.3.1.1 Security

 ESSID: Extended Service Set ID indicates the SSID which the clients used to connect

to the VAP. ESSID will determine the service type of a client which is assigned to the
specified VAP.

 Enable AP: By default, it’s “Disable” for VAP1 ~ VAP3. The VAP0 always enabled.

Select “Enable” to activate VAP or click “Disable” to deactivate this function

 Hidden SSID: Select this option to enable the SSID to broadcast in your network.

When configuring the network, it is suggested to enable this function but disable it
when the configuration is complete. With this enabled, someone could easily obtain
the SSID information with the site survey software and get unauthorized access to a
private network. With this disabled, network security is enhanced and can prevent the
SSID from begin seen on networked.

 Client Isolation: Select Enable, all clients will be isolated from each other that mean

all clients cannot reach to other clients.

 WMM: Select Enable, the packets with QoS WMM will has higher priority.

 IAPP Support : Inter Access-Point Protocol is designed for the enforcement of unique

association throughout a ESS(Extended Service Set) and for secure exchange of
station's security context between current access point (AP) and new AP during hand
off period.

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

88

*Note: IAPP only used on WAP2 security type. Only one of VAPs can be enabled

 Maximum Clients: Enter maximum number of clients to a desired number. For

example, while the number of client is set to 32, only 32 clients are allowed to connect
with this VAP.

 Service Domain: Select the desired Service Domain from the drop-down list.

 Security Type: Select the desired security type from the drop-down list; the options

are WEP, WPA-PSK, WPA2-PSK, WPA-Enterprise, WPA2-Enterprise and WEP

802.1X.

 Disable: Data are unencrypted during transmission when this option is selected.

 WEP: WEP, Wired Equivalent Privacy, is a data encryption mechanism based on a

64-bit, 128-bit or 152-bit shared key. Select WEP as the security type from the drop
down list as desired.

1) Key Length: Select the desire option are 64 bits, 128 bits or 152 bits from
drop-down list.

2) WEP auth Method: Enable the desire option among Open system or Shared.

3) Key Index: Select key index used to designate the WEP key during data
transmission. 4 different WEP keys can be configured at the same time, but only

5 Configure Wireless Connection

89 AirLive WIAS-3200N v2 User’s Manual

one is used. Effective key is set with a choice of WEP Key 1, 2, 3, or 4.

4) WEP Key: Enter HEX format WEP key value; the system support up to 4 sets of
WEP keys.

 WPA-PSK (or WPA2-PSK): WPA (or WPA2) Algorithms, allows the system accessing

the network by using the WPA-PSK (WPA2-PSK) protected access.

1) Cipher Suite: Check on the respected button to enable either AES or TKIP cipher
suites; default is TKIP.

2) Group Key Update Period: This time interval for re-keying GTK (broadcast/multicast
encryption keys) in seconds. Enter the time-length required; the default time is 600
seconds.

3) Master Key Update Period: This time interval for re-keying GMK (master key used
internally to generate GTKs) in seconds. Enter the time-length required; the default
time is 83400 seconds.

4) Key Type: Check on the respected button to enable either ASCII or HEX format for
the Pre-shared Key.

5) Pre-shared Key: Enter the information for pre-shared key; the format of the
information shall according to the key type selected.

*Note: Pre-shared key can be either entered as a 256-bit secret in 64 HEX digits format, or
8 to 63 ASCII characters.

 WPA-Enterprise (or WPA2-Enterprise): The RADIUS authentication and encryption

will be both enabled if this selected. The WIAS-3200N v2 support two 802.1x
Authentication/ Accounting RADIUS Server

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

90

1) WPA General Settings

(a) Cipher Suite: Check on the respected button to enable either AES or TKIP cipher

suites.

(b) Group Key Update Period: This time interval for re-keying GTK (broadcast/ multicast

encryption keys) in seconds. Enter the time-length required; the default time is 600
seconds.

(c) Master Key Update Period: This time interval for re-keying GMK (master key used

internally to generate GTKs) in seconds. Enter the time-length required; the default
time is 83400 seconds.

(d) EAP Reauth Period: EAP re-authentication period in seconds; default is 3600; 0

indicates disable re-authentication.

2) Authentication RADIUS Server Settings

(a) Authentication Server: Enter the IP address of the Authentication RADIUS server.

(b) Port: The port number used by Authentication RADIUS server. Use the default 1812

or enter port number specified.

(c) Shared secret: The secret key for system to communicate with Authentication

RADIUS server. Support 1 to 64 characters.

(d) Accounting RADIUS Server: Check on the respected button to enable either Enable

or Disable accounting RADIUS server.

5 Configure Wireless Connection

91 AirLive WIAS-3200N v2 User’s Manual

i. Accounting Server: Enter the IP address of the Accounting RADIUS server.

ii. Port: The port number used by Accounting RADIUS server. Use the default 1813

or enter port number specified.

iii. Shared Secret: The secret key for system to communicate with Accounting

RADIUS server. Support 1 to 64 characters.

3) WEP 802.1X: When WEP 802.1x Authentication is enabled, please refer to the
following Dynamic WEP and RADIUS settings to complete the configuration.

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

92

(a) WEP Key length: Check on the respected button to enable either 64bits or 128bits

key length. The system will automatically generate WEP keys for encryption.

(b) WEP Key Update Period: The time interval WEP will then be updated; the unit is in

seconds; default is 300 seconds; 0 indicates no re-key.

(c) EAP Reauth Period: EAP re-authentication period in seconds; default is 3600; 0

indicates disable re-authentication.

(d) Authentication RADIUS Server Settings :

i. Authentication Server: Enter the IP address of the Authentication RADIUS server.

ii. Port: The port number used by Authentication RADIUS server. Use the default 1812

or enter port number specified.

iii. Shared Secret: The secret key for system to communicate with Accounting RADIUS

server. Support 1 to 64 characters.

(e) Accounting RADIUS Server: Check on the respected button to enable either Enable

or Disable accounting RADIUS server.

i. Accounting Server: Enter the IP address of the Accounting RADIUS server.

5 Configure Wireless Connection

93 AirLive WIAS-3200N v2 User’s Manual

ii. Port: The port number used by Accounting RADIUS server. Use the default 1813 or

enter port number specified.

iii. Shared Secret: The secret key for system to communicate with Accounting RADIUS

server. Support 1 to 64 characters.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes

5.3.1.2 WDS

The administrator can create WDS Links for expanding wireless network via this page.

Please click on Wireless > Virtual AP Setup > VAP0 Setup and follow the below setting.

5 Configure Wireless Connection

AirLive WIAS-3200N v2 User’s Manual

94

 Service: By default, it's “Disable”. To “Enable” to activate WDS.

 Enable: Click Enable to create WDS link.

 WDS Peer's MAC Address: Enter the MAC address of WDS peer.

 Description: Description of WDS link.

*Note: If WDS activate, the Security Type only support “WEP” on VAP0.

Change these settings as described here and click Save button to save your changes.
Click Reboot button to activate your changes.

5.3.2 Wireless MAC Filter

For each Virtual AP, administrators can configure general settings and security type.

Click Wireless > Virtual AP, click “Edit” of Virtual AP List and then Virtual AP
Configuration page appears.