Overmax X-BEE DRONE 3.1 Plus Operating Instructions
English
1. SAFETY NOTES
** The product is designed for people aged 14 and up**
We suggest those, who are just getting started to operate drones, to contact a person with more experience
in this field. The users under 18 years of age can operate the product under adult supervision only.
The purpose of the safety notes is to protect the product and its users as well as bystanders and their
property.
Improper operation of the product can cause injuries and property damage.
SPECIALLY DESIGNED FOR INDOOR AND OUTDOOR USE
The product has been designed in a way so that it can be used both indoors and outdoors.
Before using the product, make sure that the area you chose is free from obstacles. Also, when operating the
product always keep a safe distance from people and animals.
Do not operate the product near power lines.
PREVENT THE PRODUCT FROM GETTING WET
Both the drone and the controller are composed of many precision electronic components. Therefore, they
must be prevented from getting wet. Exposure to water or moisture in any form can cause their malfunction or
damage.
DO NOT OPERATE OR EXPOSE THE PRODUCT TO RAIN OR MOISTURE
BATTERY INSTRUCTIONS
To avoid a potential fire hazard, please do not short circuit, puncture or reverse the polarity of batteries.
Battery charging should always be done under adult supervision, and at a location out of the reach of children.
DO NOT MIX NI-CAD AND ALKALINE BATTERIES
SAFETY NOTES FOR NI-MH BATTERIES
Make sure the batteries are properly installed observing correct polarity (+ -).
DO NOT MIX NI-CAD AND ALKALINE BATTERIES
If you plan not to use the quadcopter for extended period of time, remove the batteries from the controller to
avoid their leakage, which may damage the transmitter.
PLEASE DISPOSE USED BATTERIES ACCORDING TO LOCAL REGULATIONS IN SPECIAL RECYCLE
SPOTS.
SAFETY NOTES FOR LI-POLYMER BATTERIES
Li-Polymer batteries have higher operational risks when compared to ones of other types. Therefore, using
them, it is imperative to follow proper operational guidelines. The manufacturer and dealers assume no liability
for any damage caused by improper usage.
In order to avoid potential fire or explosion do not use any other charger except the one included with the
product. DO NOT crush, disassemble, burn, or reverse the polarity of the batteries.
To avoid short circuits, do not allow the metal parts to touch the battery terminals. NEVER PUNCTURE
BATTERIES; OTHERWISE IT COULD CAUSE POTENTIAL FIRE HAZARD.
Battery charging should always be done under adult supervision, and at a location out of the reach of
children.
In case of unnatural excessive heating of the batteries please stop using or charging them immediately.
Otherwise, it may cause their swelling, deformation or explosion thereby increasing the risk of fire.
**PLEASE DISPOSE USED BATTERIES ACCORDING TO LOCAL REGULATIONS IN SPECIAL RECYCLE
SPOTS. DO NOT DISPOSE OF OLD BATTERIES IN THE HOUSEHOLD TRASH
DO NOT CHARGE BATTERIES OVERNIGHT
KEEP AWAY FROM HEAT
R/C models are made from various forms of plastic that is very susceptible to damage or deformation due to
extremely high and low temperatures. Therefore, the product should not be used or stored in places where it
would be exposed to extreme temperatures.
OBTAIN THE ASSISTANCE OF AN EXPERIENCED PILOT
Although the product can be treated as a toy, it is not intended for those under fourteen years of age. Those,
who are inexperienced in piloting remote-controlled drones, must know that there will be a slight learning curve
until you become a skilled pilot. In order to make it easier to gain this skill we recommend exercises under the
supervision of professional drone pilots.
NTROLLER (TRANSMITTER) DIAGRAM
R
R
C
C
Input
Charging current
Maximum voltage
5V 700
4
B
B
Single charge
working time
C
Speed mode key
Throttle stick
Right / left migration
key
Start / landing button
Start / stop the
drone's engines
Lights button
Right / left migration
key
Photo button
Video button
Direction control stick
3D flip mode
Power LED
Forward / backward migration
key
2. CO
NTROLLER (TRANSMITTER) BATTERY INSTALLATION
. CO
3
Use a screwdriver to open the battery cover.
Place 4 AA batteries in the battery compartment. Make sure the batteries are properly installed according to
correct polarity (+ -). DO NOT MIX THE BATTERIES OF DIFFERENT TYPES
4
TERY CHARGING
. BAT
Use the included cable to charge
the baery of the drone.
**
Use ONLY the supplied USB cord for
charging.
Battery charging should always be done
under adu
lt supervision.
LED indicator
ed - on
harging completed
rger specifications
Cha
MAH
ery usage and charge duration reference
Batt
attery type
attery specification
ed - off
harging...
.2 ± 0.03V
harging time
R
echargeable lithium-
po
3
D
10
A
c
Zinc
(
1
(
Controller (transmitter)
ope
hours
N
c
Step 1
Tu
on
process.
Step 2
S
t
P
W
s
finished.
S
A
d
Th
Mode
Mode
Le
Th
Ascent / descent,
Rotate left / right
Flying forward /
backward
Direction / rotation
control stick
Left
Right
7. AUTO-CALIBRATION
lymer (Li-Poly) battery
.7V
rone flight time: up to
minutes
bout 50 minutes (charging
urrent approx. 0.75A)
-carbon battery
Non rechargeable)
RANSMITTER AND RECEIVER SYNCHRONIZATION
5. T
rn on the drone using the switch located on the underside by moving it to "ON" position. Place the drone
a flat surface to ensure the gyroscope is centered. Do not move the drone during the synchronization
witch the controller's power button to "ON" position. The LED indicator starts to blink. Wait 5 seconds until
he synchronization process starts.
ush the throttle stick from the lowest to the highest position, and then push it back to the lowest position.
hen the LED indicator stops blinking and starts to glow steadily it means that the synchronization process i
tep 3
fter the flight, move the controller's switch to "OFF" position (the power LED is off). Then, power off the
rone using the same method - move the power switch located on the bottom of the drone to "OFF" position.
e lights will go off indicating that all the systems are off.
LIGHT CONTROL
6. F
.5V
GP 15G R4P)
ration time: 18
on rechargeable (do not
harge)
Press the “Start/ stop engines” buon to start the engines.
Press the
Press the “Start / landing” button to take off.
Press the “Start / landing” button to land. In order to make the landing safe, please start the process only when
the position of the drone is not higher than 2 metres.
“Start/ stop engines” button to stop the engines.
ft / right
rottle stick
0-degree stunts
36
When you press the Flip button the controller's red LED indicator starts to blink fast indicating that the drone is
in 3D flip mode.
When in 3D flip mode, move the direction stick left or right to flip the drone in the chosen direction.
Speed modes
The device supports three flight speed modes. Press the flight speed button to switch between fast, medium
and slow mode. The number of beeps while switching informs about a currently chosen mode.
To
calibrate the drone and the remote control,
position the controller sticks as shown in the picture.
Leave them in this position until the drone’s LEDs
stop blinking (about 10 seconds). Now, the calibrated
drone is ready to fly.
8. APP:
1. Back
10. Throttle control
In order to use an android or iOS smartphone as an FPV screen please complete the following steps:
Download the „FYD-UFO” app from “Play” s
tore or „App store” and install it.
Enable Wi-Fi in your mobile phone.
Turn on the X-Bee Drone 3.1 plus Wifi.
Go to your smartphone’s Wi-Fi settings and search for “FYD-UFO -xxxxx” network. Then
establish the connection (no password needed).
Run the installed FYD-UFO app and tap “PLAY”.
The smartphone’s screen will show the live images from the drone’s camera.
FYD-UFO app button description:
2. Take a picture
3. Record a video
4. Gallery
5. Speed mode (30%, 60%,
100%)
6. Throttle lock (50%)
7. Gravity sensor mode
8. Show / hide interface
9. Rotate camera
11. / 12. Rotation control
13. /14/15/16. Left / right /
forward / backward
migration control
17. /18. Forward / backward
migration calibration
19. /20. Left/ right rotate
calibration
21. /22. Left / right migration
calibration
All the pictures and information in the manual have been submitted for illustrative purposes only and are subject to change
without prior notice.
Polski
Loading...