FW-IOB-T-120/208VAC
Input/Output/Bypass Assembly
Installation Instructions
The OutBack Power Systems FW-IOB-T-120/208VAC allows manual switching between the FX Series Inverter/
Charger and a second AC source, facilitating maintenance and power continuity.
About OutBack Power Systems
OutBack Power Systems is a leader in advanced energy conversion technology. Our products include
true sine wave inverter/chargers, a maximum power point charge controller, system communication
components, as well as breaker panels, breakers, accessories, and assembled systems.
Notice of Copyright
FW-IOB-T-120/208VAC Installation Instructions
Copyright © 2006 All rights reserved.
Disclaimer
UNLESS SPECIFICALLY AGREED TO IN WRITING, OUTBACK POWER SYSTEMS:
(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR
OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.
(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT,
CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE
USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.
Date and Revision
November 1, 2006 1.0
Contact Information
OutBack Power Systems
19009 62nd Ave. NE
Arlington, WA 98223
Phone (360) 435-6030
Fax (360) 435-6019
www.outbackpower.com
Requirements and Warnings
The OutBack FW-IOB-T-120/208VAC is intended as a system component and is included in a listing
by ETL as indoor enclosures to UL standard UL 508A Industrial Control Panels.
This enclosure is intended for battery circuits congured for 12 to 48 volts nominal.
Grounding Instructions – Each enclosure should be connected to a grounded, permanent wiring
system. For most installations, the negative battery conductor should be bonded to the grounding
system at one (and only one) point in the DC system. All installations must comply with all national
and local codes and ordinances. System grounding as required by the National Electric Code,
ANSI /NFPA 70-1996, is the responsibility of the system installer.
The equipment ground is marked with this symbol:
FW-IOB-T-120/208VAC Parts List
AC Breakers Bus Bars Red Terminal Black Terminal Blue Terminal
Bus Bar Insulators Bus Bar Insulators Bus Bar Insulators
White Terminal
Bus Bar Insulators
Breaker
Label Kit
Neutral Conductor Hot Conductors Ground Conductor Hot Conductor Hot Conductor
(White) (Red) (Green) (Black) (Blue)
AC Breaker Bypass
Slide Plate
Hardware Kit
Figure 1: FW-IOB-T-120/208VAC
Figure 2: Placement of Bus Bars
Figure 3: Sample Wiring Diagram
Installing the FW-IOB-T-120/208VAC
Bypass Breakers Output Breakers Input Breakers
(installed upside down)
Figure 4: AC Breaker Installation for FW-IOB-T-120/208VAC
To install the FW-IOB-T-120/208VAC:
• Remove the appropriate quantity of breaker knockouts from the breaker bracket.
• Pull the yellow tabs out from each breaker.
• Install the breakers on the din rail to approximately match the openings in the breaker bracket.
• Hold the breaker bracket loosely against the breakers on the din rail; move the breakers as
needed so they line up with the openings in the breaker bracket.
• With the breakers positioned properly, lock the yellow tabs to secure the breakers to the din rail.
• Install the AC Breaker Bypass Slide Plate (see Figure 5).
Installing the AC Breaker Bypass Slide Plate
Figure 5: AC Breaker Bypass Slide Plate Installation
Parts:
1. 8-32 X .75 Machine Screw (2)
2. Nylon Washer (4)
3. 8-32 Nylock Nut (4)
4. AC Breaker Bypass Slide Plate (1)
5. FLEXware AC Breaker Bracket (1)
To Assemble:
1. Remove necessary circuit breaker knockouts (per IOB kit).
2. Install AC Breaker Bypass Slide Plate and fasteners as shown in Figure 5.
3. Do not over tighten the Nylock nuts. Overtightening can cause the AC Breaker Bypass Slide Plate
to bind.
19009 62nd Avenue NE
Arlington, WA USA
(+1) 360-435-6030
900-0071-01-00 REV B
European Sales Office
Barcelona, España
(+34) 600-843-845
www.outbackpower.com
Loading...