Orion Car Audio XTR 3752, XTR 5002, 9002 User Manual
Specifications and Main Features
AMPLIFIER SECTION
- Modern Model: XTREME 3752
- Power Output 4 Ω Stereo: 93.75 watts
- Power Output 2 Ω Stereo: 187.5 watts
- Power Output 4 Ω Mono: 375 watts
- Distortion (all channels driven): <0.1% THD
- Frequency Response: 20Hz to 20kHz +0.25 dB
- Linear Bandwidth: 6Hz to 50kHz +3dB
- Signal-to-noise Ratio: > 100 dB
- Damping Factor: >400 at output connector
- Slew Rate: > 30V/µs
- Input Sensitivity: 200 mV to 5 Vrms
- Input Impedance: 47kΩ
- Fuse Type: (2) 15 AMP ATC
- Modern Model: XTREME 5002
- Power Output 4 Ω Stereo: 125 watts
- Power Output 2 Ω Stereo: 250 watts
- Power Output 4 Ω Mono: 500 watts
- Distortion (all channels driven): 0.1% THD
- Frequency Response: 20 Hz to 20 KHz +0.25 dB
- Linear Bandwidth: 6Hz to 50kHz +3dB
- Signal-to-noise Ratio: > 100 dB
- Damping Factor: >400 at output connector
- Slew Rate: > 30V/µs
- Input Sensitivity: 200 mV to 5 Vrms
- Input Impedance: 47kΩ
- Fuse Type: (2) 20 AMP ATC
- Modern Model: XTREME 9002
- Power Output 4 Ω Stereo: 225 watts
- Power Output 2 Ω Stereo: 450 watts
- Power Output 4 Ω Mono: 900 watts
- Distortion (all channels driven): <0.1% THD
- Frequency Response: 20Hz to 20kHz +0,25 dB
- Linear Bandwidth: 6Hz to 50kHz +3dB
- Signal-to-noise Ratio: > 100 dB
- Damping Factor: > 400 at output connector
- Slew Rate: > 30V/µs
- Input Sensitivity: Weights Between 200 mV to 5 Vrms
- Input Impedance: 47kΩ
- Fuse Type: (2) 30 AMP ATC
CROSSOVER
- Low Pass Crossover: Variable Low Crossover Frequency
- Low Pass Frequency Range: From 45 Hz To 5kHz
- High Pass Crossover: Variable Low Crossover Frequency
- High Pass Frequency Range: From 10hz To 10khz(bi-ranges)
- BOOST RANGE: INTELLI Q boost range 0dB To 10dB
DIMENSIONS
- XTREME 3752: 11 x 10.25 x 2.25 Inches
- XTREME 5002: 12 x 10.25 x 2.25 Inches
- XTREME 9002: 18 x 10.25 x 2.25 Inches
Frequently Asked Questions
Q1: What is the power output of the XTREME 5002 amplifier?
A1: The power output of the XTREME 5002 amplifier is 125 watts for each of its four channels at 4 ohms stereo and up to 500 watts for the 4 ohm mono.
Q2: Is there a crossover included in the amplifier?
A2: Built-in amplifiers like XTREME have the feature of adjustable high-pass or low-pass crossovers or band-pass as the case may be.
Q3: What measures are there for controlling the gain on the amplifier?
A3: the amplifier in this case supports remote gain which means you are able to adjust the gain level from afar.
Q4: What range of frequencies can the XTREME amplifiers reproduce?
A4: In terms of frequency response, it has been noted that it ranges from 20Hz to 20kHz and the deviation is placed at +0.25 dB.
Q5: The fuse employed in the XTREME 3752 is what type?
A5: It employs two 15 AMP ATC fuses.
Q6: Is it possible to set the XTREME 9002 in tri-mode configuration?
A6: Yes, the XTREME 9002 can be configured to work in tri-mode.
Q7: What is the lowest impedance that can be used with the amplifier?
A7: The lowest impedance for stereo would be 2 ohms and bridging mono would be 4 ohms.
Q8: What are the required connections for the speaker wires to be connected to the amplifier?
A8: You will need to connect to upto 12 gauge in order for optimal performance of the amplifier.
User Manual
Loading...