How it Works
Orion
Loading...
WBLS2
Specsheet
2 pgs731.26 Kb0
User Manual
10 pgs1.33 Mb0

Orion WBLS2 User Manual

Download
Installation & User ’s Guide
Individual / Video Wall Mount
MICRO-ADJUSTABLE PULL-OUT
FLAT PANEL MOUNTS
http://www.orionimages.com
All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein
http://www.orionimages.com
Installation and User’s Guide
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located on the WBLS does not exceed 150 lbs (68 kg).
2
http://www.orionimages.com
3.94" [100mm] MIN
34.57
NOTES:
EXTENSION DISTANCE IS 7.0"[177.8mm] WITH A MAXIMUM
DIMENSIONS
1.58
40.1
2.92
74.1
DIAMOND & NOTCH ALIGN WITH VERTICAL
15.10
383.4
12.00" MINIMUM SPACING
WALL PLATES SLIDE FREELY ON RAILS
30.00" [762mm] MAX
878.1
C
OF MOUNT
L
Installation and User’s Guide
WBLS
MAXIMUM MOUNTING PATTERN WIDTH IS 30.0"[762mm].1. MINIMUM MOUNTING PATTERN WIDTH IS 3.94"[100mm].2.
0 0
3.94 100
1.00
25.4
.33
8.3
10.46
265.7
13.90
353.2
14.40
365.7
17.84
453.2
18.33
465.7
19.94
506.4
MOUNT IS 3.72"[94.4mm] DEEP WHEN FLAT TO WALL.3. EXTENSION FROM WALL OF 10.7"[272mm].
.13
FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT
3.2 .62
15.7
1.11
28.2
1.60
40.7
2.09
53.2
2.59
65.7
3.08
78.2
3.57
90.7
4.06
103.2
4.55
115.7
5.05
128.2
5.54
140.7
6.03
153.2
6.52
165.7
253.2
7.01
178.2
7.51
190.7
8.00
203.2
8.49
215.7
8.98
228.2
9.48
240.7
9.97
21.00
533.4
3.72
94.4
16.52
419.6
7.00
177.8
MEASUREMENTS: [MILLIMETERS] INCHES
3
http://www.orionimages.com
LEGEND
Installation and User’s Guide
Tighten Fastener
By Hand
Adjust
Loosen Fastener
Hex-Head Wrench
Remove
Phillips Screwdriver
Pencil Mark
Optional
Open-Ended Wrench
Drill Hole
Security Wrench
TOOLS REQUIRED FOR INSTALLATION
7/32" (5.5mm) Wood Stud 5/16" (7.9mm) Concrete
#2
M5 (included)
3/16-6" (included)
1/2"
(included)
4
http://www.orionimages.com
PARTS
Installation and User’s Guide
A (8) M4x16mm
D (6) M5x16mm
G (6) M6x16mm
I (6) M8x20mm
L (8)
.750x.323x.250
B (6) M4x20mm
E (6) M5x20mm
H (6) M6x25mm
J (6) M8x30mm
M (8)
.750x.344x.500
QA (4) 5/16"
C (6) M4x25mm
F (6) M5x25mm
N (8)
[universal washer]
QB (4) 5/16"
K (4)
M8x50mm
[packed with ’N’]
P (1)
M5
R (1)
[wall mount]
(LSMVU shown)
S (2)
[security bracket]
T (2)
[hold-back bracket]
W (1)
3/16 -6"
QC (4) 5/16" x 2-1/2"
U (1)
[left pull-out upright]
(LSMVU uprights shown)
V (1)
[right pull-out upright]
X (1)
1/2"
Y (4) [wall bracket cap] (LSMVU only)
5
http://www.orionimages.com
INSTALLATION
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the mount is being attached is capable of supporting five times the weight of the WBLS and all attached equipment not to exceed 150 lbs (68 kg).
NOTE: Proceed to either the Installing WBLS to a Wood
Stud Wall, Installing WBLS to Wall - Concrete, Concrete Block
IMPORTANT ! : For video wall mounting, mounts should
be installed one screen height apart vertically and approximately one screen width apart horizontally. (See Figure 1)
Installation and User’s Guide
Figure 2
5. Using a level, mark the wall on each stud to attach the mount through the upper mounting slots. (See Figure 3)
Figure 1
Mounting WBLS to Wall
The WBLS has been designed to be mounted directly onto either a wood stud or concrete wall.
Installing WBLS to a Wood Stud Wall
1. Determine the center of the TV screen, and where it should be located on the wall.
2. Locate the closest stud to the left and right of the selected location.
NOTE: If the screen area lies over a stud, use that stud and the
stud to either the left or right of it.
3. Line up the notches on mount (R) with center of screen marking to determine vertical center. (See Figure 2)
4. Measure up 7-1/2" (190.5mm) from the center point to mark location of the upper mounting slots. (See Figure 2)
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.
Figure 3
6
http://www.orionimages.com
6. Drill one 7/32" pilot hole in each stud.
7. Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat washers (QB) to attach top of mount (R) to wall. (See Figure 3)
8. Mark the attachment points for the lower mounting slots, making sure the attachment points are located on the studs. (See Figure 3)
9. Drill 7/32" pilot holes at markings for lower mounting holes. (See Figure 3)
10. Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat washers (QB) to attach the mount to the wall through the lower mounting holes. (See Figure 3)
11. Slide rails to approximate center of screen location.
Installing WBLS to Wall - Concrete, Concrete Block
1. Determine the center of the TV screen, and where it should be located on the wall.
2. Line up the notches on mount (R) with center of screen marking to determine vertical center. (See Figure 4)
3. Measure up 7-1/2" (190.5mm) from the center point to mark location of the upper mounting slots. (See Figure 4)
4. Using a level, mark the wall through both upper mounting slots. (See Figure 4)
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 12" (304.8mm). Do not place mounting brackets closer together than 12" (304.8mm).
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY! ALWAYS make certain area behind mounting surface is free of gas, water, waste, or any other plumbing before cutting, drilling, or installing fasteners.
Installation and User’s Guide
8
(QB) x 4
4
x4
5
9
6
10
(R)
7 11
(QA) x 4
(QC) x 4
Figure 4
5. Drill one 5/16" pilot hole at each marking.
6. Install an anchor (QA) into each upper pilot hole using a hammer, making sure that the anchor is flush with the wall.
7. Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat washers (QB) to attach top of mount (R) to anchors in wall.
8. Mark the attachment points for the lower mounting slots. (See Figure 4)
9. Drill one pilot hole at each marking for lower mounting holes. (See Figure 4)
10. Install an anchor (QA) into each lower pilot hole using a hammer. (See Figure 4)
11. Use two 5/16 x 2-1/2" lag bolts (QC) and two 5/16" flat washers (QB) to attach the mount to the wall through the lower mounting holes. (See Figure 4)
12. Slide rails to approximate center of screen location.
7
http://www.orionimages.com
Installation and User’s Guide
Attaching Interface Brackets to TV
1. Align the center of the pull-out uprights (U and V) with center of screen. (See Figure 9)
NOTE: The diamond-shape hole in the bracket corresponds to
the center of the mount.
Pull strap
Center of bracket
Figure 9
2. Adjust Velcro® pull strap (if necessary) so it does not extend beyond bottom of screen. (See Figure 11)
NOTE: Do NOT allow both interface brackets (U and V) to be
located on same side of wall bracket. (See Figure 11)
NOTE: NEVER place both interface brackets (U and V) to one
side of the wall mount center line! (See Figure 11)
Center Line (CL)
Pullstrap
NEVER place both interface brackets to one side of the wall mount center line (CL)!
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display. Properly sized screws will easily and completely thread into display mounting holes. If spacers are required, be sure to use longer screws of the same diameter.
2. Select correct screws, spacers (if necessary) and universal washers from the hardware bag (A-N) and attach brackets (U and V) to back of screen. (See Figure 9)
NOTE: Uprights may need to be pulled out to the extended
position in order to install screws through proper holes.
Attaching Screen to Wall Mount
1. Attach wall bracket caps (Y) to top and bottom of both wall brackets. (See Figure 10)
Both interface brackets must NEVER be located to one side of the wall brackets!
Figure 11
3. Hang top hook of interface brackets (U and V) onto the top bar of the mount (R). (See Figure 12)
4. Slide screen and bars to desired viewing position.
5. Route cables between wall and bars.
NOTE: The pull-out feature allows the screen to be pulled away
from the wall for easy cable access following installation.
(Y) x 4
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
6. Pull downward on the pullstraps and swing inward toward wall, latching interface brackets to lower bar and locking
Figure 10
bottom of screen to the mount. (See Figure 12)
8
http://www.orionimages.com
Top Hook
Installation and User’s Guide
Adjusting Roll/Height of Wall Brackets
+
NOTE: The height adjust wall brackets allow adjustment of
1. Turn to right (tighten) to raise side of screen (See Figure 14).
2. Turn to left (loosen) to lower side of the screen.
1
Raises screen
1/2".
3
Pullstraps
(Screen not shown for clarity)
6
Figure 12
Plumb Adjustment
1. Using the provided 1/2" wrench (X), turn plumb adjustment bolt to the left to adjust screen away from the wall. (See Figure 13)
2. Using the provided 1/2" wrench (X), turn plumb adjustment bolt to the right to adjust screen toward the wall. (See Figure 13)
2
(W)
(Screen not shown for clarity)
Lowers screen
Figure 14
Locking Mount (Optional)
1. Add security bracket (S) to the mount. (See Figure 15)
2. Add padlock (not included) through holes on small security bracket (S) and mount.
3. Add hold-back bracket (T) to the mount to secure mount in recessed position. (See Figure 15)
4. Repeat Steps 1-3 for the other upright for additional security.
(T)
3
(S)
1
1
Figure 13
21
plumb adjustment
2
bolt
Figure 15
2
9
http://www.orionimages.com
Installation and User’s Guide
ORION Images, Corporation. Design, Develop, Manufacture LCD / LED
Security Monitors
2011 ORION Images, Corp. All rights reserved
www.orionimages.com
USA / Headquarter A 7300 Bolsa Avenue, Westminster CA 92683
P 714-766-6300 F 714-766-6310
Europe / UK A 102 Knightwood Crescent, New Malden,
Surrey. KT3 5JW U.K.
P
+44 (0) 7979-152-943
Asia / Korea A 403-403, Bucheon Technopark 4 Danji Apt.,
193, Yakdae-dong, Wonmi-gu, Bucheon-si, Gyeonggi-do 420-734, Korea
P 82-70-8240-4400 F 82-70-8240-4403
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use