7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg2
http://www.orionimages.com
WARNING
WARNING
WARNING
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A
MAXIMUM WEIGHT OF 50 LBS. IF NOT, THE WALL MUST BE REINFORCED.
PROPER INSTALLATION PROCEDURE BYAQUALIFIED SERVICE TECHNICIAN,
AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED
TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR
EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS
FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION
INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
Indicates that the power plug is to be disconnected from the power outlet.
Safety precautions must be taken at all times.
Warning and Caution statements.
A secure structure must support the weight, or load, of the display. When mounting
to a wall that contains wooden studs, dead center of the wooden stud must be
confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of
impact. Failure to do so could result in damage to the display and/or damage to the
mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other
source of direct heat energy. Failure to do so may result in damage to the display
and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or
damage can result from dropping or mishandling the display.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the
mount is to be installed on any surface other than wooden studs, use suitable
hardware (which is commercially available).
Contact Orion Images with any technical/ installation questions.
Installation and User’s Guide
Warning Statements
3
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg3
(
http://www.orionimages.com
Installation and User’s Guide
Part List
NOTE
Installation Tools
Phillips Head Screw Driver, Soft Material/ Blanket, 5/16” Socket and Wrench
Pencil Tape Measure, Drill Gun,
This wall mount is shipped with all proper installation hardware and
components. Make sure that none of these parts are missing and/or
damaged before beginning installation. If there are parts missing and/or
damaged, please stop the installation and contact Orion Images.
-
-
WB-71 Wall
Plate (1ea)
5/16” Flat
Washers (12ea)
M6 x 30mm Lateral Shift
Locking Screws (2ea)
M6 x 12mm Safety
Knobs (2ea)
Mounting
Brackets
5/16” x 3” Lag Bolts
(wooden studs only) –
(12ea)
2ea)
Griplates™
(8ea)
Thread Depth
Indicator
4
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg4
http://www.orionimages.com
Installation and User’s Guide
5
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg5
http://www.orionimages.com
Nylon spacers and flat washers actual size
NOTE
The nylon spacers may be stacked to achieve proper spacing.
1/2" Nylon spacers
(Qty 6)
(large)
5/16" Flat washers
(metal)
(Qty 6)
1/4" Nylon spacers
(Qty 6)
Installation and User’s Guide
6
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg6
r
http://www.orionimages.com
1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the
flat panel to make sure the inserts measure the same full depth and mark it (Figure 1).
2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws
(supplied).
3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE
this screw.
4. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3),
until you find one that comes closest to your mark without going past.
Thread Depth Indicato
Installation and User’s Guide
7
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg7
p
http://www.orionimages.com
Installation and User’s Guide
NOTE:
WARNING:
1. Once the flat panel is inverted, use a measuring tape to find the center of your flat panel
2. Using a pencil lightly mark the center of your flat panel (Figure 5).
Proper installation procedure by qualified personnel as outlined in the installation
instructions must be adhered to. Failure to do so could result in serious personal injury
ossible damage to the flatpanel.
and
INVERT THE FLAT PANEL PLACE IT ON A SOFT, FLAT SUFRACE TO
PREVENT DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC.
FAILURE TO DO SO WILL RESULT IN DAMAGING THE FLAT PANEL. DO NOT
LAY THE FLAT PANEL ON THE FLOOR WITHOUT ANY PROTECTION TO THE
GLASS. THE FLAT PANEL IS HEAVY AND FRAGILE. AT LEAST (2) QUALIFIED
PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF
THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY
AND POSSIBLE DAMAGE TO THE FLAT PANEL.
measuring from outside to outside of the chassis (Figure 4).
Mounting Bracket Installation
8
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg8
http://www.orionimages.com
3. Install the nylon spacers (if needed) to the mounting points on the flat panel (Figure 6).
4. Lay the left and right mounting brackets (stamped arrows facing out) - (Figure 7).
Installation and User’s Guide
5. Match the center of viewing guide with the centerline you marked in Step 1 (Figure 8).
6. The mounting brackets are designed with a center of viewing guide on the outside (Figure 9).
9
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg9
http://www.orionimages.com
Installation and User’s Guide
7. The Griplates™ have M4, M5 M6 and M8 hole patterns to fit the hardware that your flat
panel requires.
EXAMPLE:
8. Once the mounting brackets are aligned secure the Griplate™ to the flat panel. Use (1)
Griplate™ per mounting
NOTE:
The dimples of the top plates have to be facing up and the bottom dimples must be
facing down.
If your plasma uses M8 x 20 Phillip screws. Use the M8 mounting points (Figure 10).
point (Figure 11).
10
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg10
W
(
http://www.orionimages.com
Installation and User’s Guide
1. Using a (commercially available) wood stud finder, locate the 16" stud centers behind th
wall (Figure 12).
2. Once found, make a pencil marking on the center of the wood studs (Figure 13).
3. Place the wall plate to the reference line and mark the six (6) lag bolt mounting points
through the wall plate slots on the wall.
B-71 Installation
Wood Stud Finder
Commercially
Mark the wall
and the center
of the wood
studs.
Wood studs
behind the
wall
structure.
Measure and
mark the
viewing height
desired on the
wall.
11
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg11
http://www.orionimages.com
4. Level the wall plate with the reference arrow pointing up to the ceiling (Figure 15).
5. Drill six (6) ¼" pilot holes to the marked wall.
6. Secure the plate using the six (6) 5/16" lag bolts and flat washers (Figure 16).
Installation and User’s Guide
12
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg12
(Fig
http://www.orionimages.com
Installation and User’s Guide
WARNING:
1. Raise the flat panel with the LEFT and RIGHT mounting brackets secured to the flat panel
and insert the top hooks over the upper rod. The lower hooks should rest on the lower rod
Installing the Flat Panel Display (WB-71)
AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED
FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD
RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT
PANEL.
ure 17).
13
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg13
g
http://www.orionimages.com
2. Make any lateral shift adjustment and lock it by tightening the two (2) M6 x 30mm Phillips
screws found on the bottom of the mounting brackets. Use the foot leveler to adjust your
plasma.
Installation and User’s Guide
CAUTION:
NOTE:
Do not over ti
To remove the display from the wall simply back off the M6 x 30mm screws using
hten the M6 x 30mm screws to the rods (Figure 18).
a Phillips screwdriver and lift the unit of the wall carefully.
14
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg14
http://www.orionimages.com
3. Tilt the flat panel and secure the two (2) M6 x 12mm safety knobs to each of the mounting
brackets (Figure 19).
Installation and User’s Guide
NOTE:
To remove the display from the wall simply extend the display to its maximum tilt
range, remove the two 6 (mm) safety knurl knobs push the flat panel back to it’s
flat position, loosen or remove the two (2) M6 x 30 lateral shift screws and lift the
unit of the wall.
15
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg15
http://www.orionimages.com
Installation and User’s Guide
A. Wall plate
B. Mounting brackets
C. Griplate™
D. Mounting hardware
E. M6 x 30 (mm) Phillip screws
F. Wood stud
G. 5/16” x 3” Lag screws and flat washers
H. Safety knobs
Technical Specifications
16
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg16
y
http://www.orionimages.com
All Orion Images products carry a limited lifetime warranty from ship date against defects in
materials and workmanship. Orion Images is not liable for improper installation that results in
damage to mounts, adapters, display equipment or personal injury.
Contact Orion Images
In the event of missing and/or damage equipment, or technical questions, the
following information can help in the completion of the installation.
Address: 7300 Bolsa Avenue, Westminster, CA 92683
Tel: 714-766-6300 / Fax: 714-766-6310
Email: sales@orionimages.com
Website: http://www.orionimages.com
Limited Lifetime Warrant
Installation and User’s Guide
17
7300 Bolsa Avenue, Westminster CA 92683 / Tel: 714-766-6300 / Fax: 714-766-6310
pg17
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.