Orion OPM-4260, OPM-4260R User Manual

• 2012.10.10

Thank you for purchasing our MPDP.

Please read through this user's manual for safety before installing this product.

This product is manufactured for Multi Plasma display model only.

User’s Manual

OPM-4260 | OPM-4260R

Infinitely Expandable

MPDP

A revolutionary MPDP

A revolutionary MPDP

Infinitely Expandable MPDP

Address: 257-6, Gongdan-dong, Gumi-si, Gyeongsangbuk-do, Korea

Tel : [phone], Fax: [phone]

ORION CO., LTD.

www.oriondisplay.net

- 1 -

Notice to users

Class A digital device

It is a device designed for business purpose with a safety certificate for electromagnetic interference, which
user should be mindful of.

" Important Safety Instructions"

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
The symbol in gure 21 shall be shown adjacent to the text of item 12 above.

Features of MPDP

▶ Enjoy a wide flat screen with high brightness and high quality.

▶Easy to install and move due to its thin design
▶Enjoy your favorite programs with various split-screen features simultaneously presenting

several programs.

To prevent electric shock, Do not remove cover.
No user serviceable part inside
Refer servicing to qualified service personal.

Warning

Thank you for purchasing our MPDP monitor.

This manual describes how to use the product and notes in use.
Please read the manual carefully before using it.
After reading this manual, please retain for future reference.
If you have any questions or a problem occurs, please contact either the company you purchased this
product from or an authorized service center.

※Displaying static picture for an extended period of time may cause an burn-in effect.

Brightness drop or pixel problem caused by burn-in effect are not the subject to warranty service.

If you fail to comply with the regulations for safety and proper use,
fire or injury may be caused.

Warning

User's Manual

Multi-Screen Control
System(MSCS)

Guide Pin (4pcs) Ferrite Core (1pc) Handle (2 pcs)

RS-232C Cable

Bolt (4 pcs)

DVI-D Cable Power Cable

Supplied Accessories

PDP

REMOTE CONTROL

ON OFF

INFO

A

SET

DVIC1 DVIC2 INFO AUTO

VIDEO S-VIDEO HDSDI

DVI PC DTV HDMI

B

BROADCAST

ID SETTING

ON

OFF

1 2 3

4 5 6

7 809

DVI 1

DVI 2

OUTPUT FUNCTION

DVI CONVERTER INPUT

MPDP

Optional Accessories

MAIN FRAME

(refer to page 16~17)

DVI Converter

(ODC-10000)

New MFC SET

※ The ferrite core is used to shield the power cable from interference.
※ When connecting a cable, open the ferrite core and clip it around the cable near the plug.

Innitely Expandable

- 2 - - 3 -

Contents

※Cautions for consisting MPDP System ..............................................................................................4

※ Clearance for Ventilation ..............................................................................................................................6

※ Do not cover the vent hole for the fan ..................................................................................................7

※Cleaning and Maintenance .........................................................................................................................7

※ Please keep following instruction for panel protection without exception. .....................8

※Handle with Caution. ......................................................................................................................................9

1. Safety Precautions .......................................................................................................................................12

2. How to Install ...................................................................................................................................................14

3. Guidance for Users ......................................................................................................................................18

4. How to Connect Cables ............................................................................................................................20

4.1. Connection of Single MPDP ..............................................................................................................................20

4.2. Connection of Multiple MPDP............................................................................................................................22

4.3. Connection of Control Cable - In case of using MSCS .......................................................................................24

4.4. Connection of Control Cable - In case of using the other control program besides MSCS .................................26

4.5. Connection of DVI cable ....................................................................................................................................28

4.6. Connection of optional accessory .....................................................................................................................29

4.7. ID setting of X x Y MPDP ...................................................................................................................................30

5. Setting and operation of MSCS software ........................................................................................31

5.1. MSCS Installation ..............................................................................................................................................31

5.2. Start MSCS .......................................................................................................................................................32

5.3. Setting of COM Port ..........................................................................................................................................33

5.4. Setting of LAN Port (In case of connecting to a LAN Hub) .................................................................................34

5.5. Setting of LAN Port (In case of connecting directly to user's computer) ............................................................36

5.6. "New design/Last design" setting ......................................................................................................................39

5.7. Multi-screen configuration .................................................................................................................................40

5.8. Selecting the command transmission method ...................................................................................................40

5.9. Power On/Off ....................................................................................................................................................41

5.10. Changing the input source .............................................................................................................................44

5.11. Slide Control ...................................................................................................................................................47

5.12. Picture Control ................................................................................................................................................50

5.13. Timer Control ..................................................................................................................................................51

5.14. Sync Control ..................................................................................................................................................52

5.15. Tracking Control .............................................................................................................................................53

5.16. ORION Homepage log on and Version Information ..........................................................................................54

6. Control Method of optional accessory ..............................................................................................55

6.1. New MFC ........................................................................................................................................................55

6.2. DVI Converter .................................................................................................................................................58

7. MSCS Protocol ...............................................................................................................................................66

※Attachment : ASCII to HEX Conversion Table ........................................................................................................84

8. Other tips ...........................................................................................................................................................85

8.1. Before calling for service....................................................................................................................................85

8.2. About Plasma display panel ..............................................................................................................................86

9. Applicable DVI signals ................................................................................................................................87

10. Specification ..................................................................................................................................................88

11. Option Specification .................................................................................................................................90

11.1. DVI Converter ..................................................................................................................................................90

11.2. New MFC ........................................................................................................................................................91

NOTICE

1. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket,
therefore the mains plug shall be readily operable

2. WARNING - To reduce the risk of re or electric shock, do not expose this appliance to rain or
moisture.

3. Apparatus shall not be exposed to dripping or splashing and no objects lled with liquids, such
as vases, shall be placed on the apparatus.

4. Use only a properly grounded plug and receptacle

5. "Warning" CAUTION – These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the
operating instructions unless you are qualied to do so.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufcient magnitude to
constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and
maintenance(servicing) instructions in the literature accompanying the appliance.

OPM-4260 | OPM-4260R

Innitely Expandable

※Cautions for consisting MPDP System

Environmental condition for installation

- Since MPDP panel is very sensitive for physical impact, installation requires
considerable caution.

- Minimum clearance(20cm) must be secured for smooth ventilation. (See
P16~17)Installation must avoid air tight or near air tight places. Improper
ventilation causes malfunction and shortens product lifetime by rapid internal
temperature rise. If MPDP has to be installed at the improper ventilation,
additional ventilation openings or fans must be provided to keep the internal
temperature between 0 ~ 35˚C.

- For ground of MPDP and application devices, it should be connected as frame
ground.

- Considering MPDP Max power consumption, check the main electric
specication.

Consideration for easier service

- When you design the exterior design for MPDP system, consider easier
disassembly for possible service occasion in the future.

- The sliding Universal Unit of ORION is recommended for easier service.

- If service people can step into the backside of MPDP system, it can greatly
reduce time and effort for service.

- In case of higher locations, consider the installation location and exterior design
for easier service.

※ If the internal temperature reaches to 90˚C, "High Temperature" signal will be

displayed at the lower left corner on the screen for 1minute and the MPDPset
will be turned off automatically.

※ Please be noted that the lm lter on the front surface of the panel may lose its

color or change the color rapidly, if it is exposed to sunlight or ultraviolet rays.

The number of Daisy chain connection

- The image quality may vary depend on the quality of signal and cable condition.

INPUT SOURCE Resolution Connection Remark

DVI 1600 x 1200 x 60Hz 6 sets HDCP Available

PC 1600 x 1200 x 60Hz 3 sets

VIDEO NTSC, PAL, SECAM 6 sets

RS-232C 30 sets ORION Cable Only

- If you need to use more MPDP sets than indicated in the table, using a DVI
distributor is highly recommended.

Caution for the other control program besides MPDP
Control Program (MSCS)

- If you want to use automatic power on/off function that make MPDP turned on/
off by connecting main power, allow at least 20 seconds of Stand-by time before
MPDP is turned on, when you make control program.

- If RS-232C communication signal or other image signal is applied to 9 or more
sets simultaneously, communicational error may occur. (Power on & Broadcast)

- 4 - - 5 -

WARNING

WARNING

OPM-4260 | OPM-4260R

Innitely Expandable

- When you install MPDP, make sure there is at least 20cm clearance for
effective ventilation and do not seal off MPDP sets.
If MPDP sets are installed at the locations of bad ventilation, the inner
temperature can be raised rapidly and it can cause frequent malfunctions
and rapid reduction of the product life.

※ Ventilation space in front of MPDP must be furnished for heat dispersion.

If the front space of MPDP has to be sealed, there must be consideration
for the heat dispersion in the rear side of MPDP.

- Carefully install MPDP not to cover the fan air holes with any structural
object.
If the holes are covered with anything, the inner temperature can be
raised rapidly and it can cause malfunctions.



- Regularly clean off the vent holes in the back of MPDP sets.
If the vent holes and the fan air holes are clogged with dust, it prevents
the air ow inside of MPDP sets.
It can cause rapid increase of the inner temperature and may cause
malfunctions.
Clean off the vent holes and the fan air holes with a vacuum cleaner
regularly.

※ 

Clearance for Ventilation

※ 

Do not cover the vent hole for the fan

※

Cleaning and Maintenance

Installationstructure

DOWN

UP

PDP

CO., LTD.

Made in Korea

• Model Name : OPM-4260

• Voltage : AC~100 - 240V

• Current : Max. 4A

• Frequency : 50/60Hz

• Serial No :

MPDP

FCC Verified : Class "A"

This device complies with the Part 15 of the FCC Rules.
Operation is subject to the following two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received,
including interference that may cause undesired operation.

To prevent electric shock,
Do not remove cover.
No user serviceable part inside Refer
servicing to qualified service personal.

RISK OF ELECTRIC SHOCK
DO NOT OPEN

CAUTION

ID SELECT

FANSTBPWR ON

AUDIO/VIDEO
APPARATUS
E329824
42SS

VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

FAN

ID SELECT

VIDEO

DVI-D

RS-232C

PC

SVC

LAN

PDP

Made in Korea

MPDP

•

감전사고 예방을 위하여,
덮개는 열지마세요.

•

내부에는 소비자가 수리할 수
있는 부품이 없으므로,
고객 A/S팀으로 연락하십시오.

• 제 품 명 칭 : PDP Monitor

• 모 델 명 : OPM-4260

• 정격전압전류 : AC 100-240V~,

4A, 50/60Hz

• 인증자상호 :오리온피디피(주)

• 제조업체명 :오리온피디피(주)

• 구입 및 A/S : 054) 460-5887

• 제 조 년,월 :

VacuumCleaner

- 6 - - 7 -

WARNING

WARNING

OPM-4260 | OPM-4260R

Innitely Expandable

- 8 - - 9 -

WARNING

WARNING

WarningWarning

※Handle with Caution.

- Shock/Impact on the set's sides will result in internal
circuit damages.

- The edge/bottom of the panel are fragile.
Use shock-absorbing pads or rugs for laying down
the product.

※ Please keep following

instruction for panel
protection without exception.

- This product can be damaged even with minor
impact for its nature.
Please keep following instruction to carry or store
the products.

• Please do not stand PDP alone.
It may fall or slip off and Panel
can be broken or damaged.

• If you need to stand PDP, you
must use handles on the back
and lean over the PDP to avoid
panel touches ground or oor.

• Please do not lean over the PDP.
It may damage the bottom part
of the PDP.

• If you need to lay down PDP as
face down position, please use
shock-absorbing pads under the
PDP.

• Please do not lean over the PDP
toward the edge part. It may
damage the edge part of the PDP.

• If you need to lay down PDP
as face up position, please be
cautious for falling objects on the
surface of the PDP.

PANEL PANEL

PANEL

PANEL

CUSHION

PANEL

OPM-4260 | OPM-4260R

Innitely Expandable

- 10 - - 11 -

WARNING

WARNING

Open Structure

Unlike consumer PDP product, the panel of MPDP is exposed without
any protective chassis.
It needs extra caution to carry or install to prevent any impact.

How to carry MPDP

Please see page 14 for unpack and handle assembly.
It always needs two persons to carry or install MPDP.
When you carry MPDP with up straight manner, please hold handles on the
back and bottom part of the panel together.
Please be careful not to touch the bottom part of the panel when you put
down the panel.

When you carry MPDP with flatbed manner, please hold handles on the
back and lower part of the back.
Please be careful not to touch the bottom part of the panel when you put
down the panel.

Please do not touch the panel with your hand.

PANEL

MASTER FRAME

• OPM-4260 • OPM-4260R

It has to be handled with
care, because the panel glass
substrate is exposed without
side cover.

Although Panel is protected
with a Side cover, it is still
sensitive to the impact or
shock from outside.

OPM-4260 | OPM-4260R

Innitely Expandable

- 12 - - 13 -

1. Safety Precautions

• If it operates abnormally, stop using it
immediately.

• Please refer to a specialized
construction company for installing stand
or wall mount unit. Otherwise, damage
or injury may be caused.

•Avoid any action to damage the power
cord or power plug. It may cause fire or
electric shock.

•Do not alter (or disassemble) the
product. It may cause electric shock
since high voltage is flowing inside.

• Do not place any liquid-containing
container on it. If the inside is wet, it
may cause electric shock or fire.

•Do not touch the device when lightning
strikes.

•Do not pull out the power plug with a wet
hand. It may cause electric shock.

•Do not install the product where it may
be exposed to direct sunlight or near
any heating device. It may shorten the
product's life span or cause failure.

• Do not put any foreign material into
the product. It may cause a failure or
shorten the life span.

• Do not install in an unstable location
It may cause injury.

•Do not exceed ratings of AC outlet
or extension cords. It may cause failure.

• Make sure the product is not covered
with any object. If the ventilation hole is
blocked, the inside temperature may rise
to cause overheating resulting in fire.

•Do not poke the front screen with sharp
material. It may damage the screen and
may cause malfunction of the product.

•Do not lean against the product or keep
it leaned. It may cause injury or failure.

• Do not put it at any place with much
humidity, dust, oil, smoke or steam. It
may cause failure.

•If you do not want to use the product
for a long time, keep the power plug
unplugged to save electricity.

•The socket-outlet should be installed
near the equipment and be easily
accessible.

•Do not put any heavy object on it.
It may cause failure.

MPDP

•Do not pull out or hang down the
connection cable. It may damage the
cord to cause fire or electric shock.

• Pull out the power plug by holding the
plug. Otherwise, it may damage the
power cord to cause fire or electric
shock.

•Do not ride or step on the product It may
cause breakage when fallen down.

•When moving it, disconnect the
connecting cable. Otherwise, it may
damage the cable to cause fire or
electric shock.

•Install the product on safe and flat
surface.

•Do not put candles on the product. If the
liquid flows inside the product. It may
cause electric shock or fire.

•Donottouchproduct’sfrontsurfacewith

hand. Otherwise, the image quality can
be lowered.

OPM-4260 | OPM-4260R

Innitely Expandable

- 14 - - 15 -

2. How to Install

MPDP

MPDP

MPDP

Panel

Master frame

MPDP

MPDP

How to assemble handles

• Install this set only at a location where adequate ventilation is available.

1. Product is packed in a box as shown in Figure 1.

2. Please carefully remove the Packing Bag with a knife or a pair of scissors.
※ Please check front and rear side before you cut the bag to prevent any damages

on panel or set.

3. Please assemble handles with the bolts that are in the accessory box to the
rear side as shown in the figure.

Handles

Packing Bag

[Figure 1]

[Figure 3]

[Figure 2]

[Figure 4]

Panel protection

How to move MPDP

1. 2 people hold each handle on product's back side.

2. It needs two people to carry or install this product.

Please hold the handles in the back and the front bottom part at the same time.

- Please do not grab the panel, but grab bottom of master frame when you carry or install the products.

- Please use gloves when you carry or install the products.

※ Attention :

- Do not remove the panel protection pad until a set is completely installed on a stand or a
wall hanger.
Please carefully remove Panel protection pad to prevent any damages on the product .

-Please make sure to use panel protection when you move, carry or rent MPDP.

Handles

Panel protection

Panel protection

OPM-4260 | OPM-4260R

Innitely Expandable

- 16 - - 17 -

Install on a MAIN FRAME Stand

Please secure minimum clearance as shown in the picture for adequate ventilation and technical service.

MAIN FRAME Stand Unit (Option)

• The set can be installed as shown below.
(For further information, refer to the optional 'MAIN FRAME Installation and Setup Guide'.)

MAIN FRAME Wall Mounting Unit (Option)

• The set can be installed on the wall as shown below.
(For further information, refer to the optional 'MAIN FRAME Installation and Setup Guide'.)

Mount on the MAIN FRAME wall

Please secure minimum clearance as shown in the picture for adequate ventilation and technical service.

• Please do not install our product at following locations to protect the product
and prevent possible malfunction.

- Places of vibration or shock: PDP set may fall and damaged

- Next or near to Sprinkler sensors: The sensors may detect heat from a set and sprinkler can be activated.

- Around high voltage power lines: Noise from the power line may affect screen images

- Around heating apparatus: PDP set may be overheated and damaged.

• Please check the stability of wall.
If the wall is not strong enough, reinforce the wall before installation.

• Please connect all the cables to proper ports in a set before installation.

Hanger

Hanger Bolt

PDP

MAIN

FRAME

Guide Pin

Guide Pin

Hanger

Hanger Bolt

PDP

MAIN

FRAME

WALL

BRACKET

20cm

20cm

20cm

20cm

20cm

20cm20cm

OPM-4260 | OPM-4260R

Innitely Expandable

- 18 - - 19 -

3. Guidance for Users

n Input/Output Terminals

DOWN

UP

PDP

CO., LTD.

Made in Korea

• Model Name : OPM-4260

• Voltage : AC~100 - 240V

• Current : Max. 4A

• Frequency : 50/60Hz

• Serial No :

MPDP

FCC Verified : Class "A"

This device complies with the Part 15 of the FCC Rules.
Operation is subject to the following two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received,
including interference that may cause undesired operation.

To prevent electric shock,
Do not remove cover.
No user serviceable part inside Refer
servicing to qualified service personal.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

ID SELECT

FANSTB PWR ON

AUDIO/VIDEO
APPARATUS
E329824
42SS

VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

PDP

CO., LTD.

Made in Korea

• Model Name : OPM-4260

• Voltage : AC~100 - 240V

• Current : Max. 4A

• Frequency : 50/60Hz

• Serial No :

MPDP

FCC Verified : Class "A"

This device complies with the Part 15 of the FCC Rules.
Operation is subject to the following two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received,
including interference that may cause undesired operation.

To prevent electric shock,
Do not remove cover.
No user serviceable part inside Refer
servicing to qualified service personal.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

ID SELECT

FANSTB PWR ON

AUDIO/VIDEO
APPARATUS
E329824
42SS

VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

❶

❷

❸

❹

❺

❼

❻

❽

1. ID SELECT

Set ID Switch

2. VIDEO Input / Output

Composite Signal, BNC

3. PC Input/Output

Analog RGB Signal, D-Sub 15pin

4. DVI-D Input/Output

Digital RGB Signal(TMDS),
single link 24pin

5. RS-232C Input/Output

MPDP Control, Upgrade by Com Port,
D-sub 9pin

6. SVC

For the exclusive use of service, RJ11

7. LAN

MPDP Control by Ethernet, RJ45

8. AC Input

AC 100V ~ 240V, 50/60Hz

DOWN

UP

PDP

CO., LTD.

Made in Korea

• Model Name : OPM-4260

• Voltage : AC~100 - 240V

• Current : Max. 4A

• Frequency : 50/60Hz

• Serial No :

MPDP

FCC Verified : Class "A"

This device complies with the Part 15 of the FCC Rules.
Operation is subject to the following two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received,
including interference that may cause undesired operation.

To prevent electric shock,
Do not remove cover.
No user serviceable part inside Refer
servicing to qualified service personal.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

ID SELECT

FANSTB PWR ON

AUDIO/VIDEO
APPARATUS
E329824
42SS

VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

n Set ID Switch Setting

• Example of ID Switch setting

- You can set ID with 3 rotary switches as shown in the following figure.

※ When you set ID of MPDP set, power cable must be disconnected. If power cable is not

disconnected during ID setting, MPDP set may be operated with the previous ID and it may
cause abnormal behavior.

※ For stable operation, wait for at least 10 seconds prior to use MPDP control program after the

first AC power connection.

[PDP ID 01]

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

[PDP ID 15]

0

1

2

3

4

5

6

7

8

9

100digit10digitsingledigit

100digit10digitsingledigit

• LED Indication

LED Indication Description

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

FANSTB PWR ON

No Power.

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

STB PWR ON FAN

Insert power cord(Stand-By state)

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

FANSTB PWR ON

Power On By MSCS.

The PWR ON LED blinks continually.

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

FANSTB PWR ON

Power Off by MSCS Program.

(System ready).

FAN : Normal - LED Off, Abnormal - LED On

IF FAN LED is turned on, please check FANs.

ON OFF BLINKING

OPM-4260 | OPM-4260R

Innitely Expandable

※ It is highly recommended to use

RS-232C cable provided by ORION.
If you want to use the other RS-232C
cable, it must be shielded.

- 20 - - 21 -

ID SELECT VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

FANSTB PWR ON

4. How to Connect Cables

• Do not connect/disconnect cables while MPDP or other external equipments are turned on.

• First turn off the power all the attached equipment and make connections.

• Make sure the power cord is inserted properly into the power inlet to prevent unexpected
pullout of the cord.

4.1. Connection of Single MPDP

• MPDP and PC should be connected; a Com Port in a PC and RS-232C IN port in a MPDP is
connected with supplied RS-232C cable.

• MPDP On/Off or Screen adjustment can be controlled by MSCS (Multi-Screen Control
System).

• ID setting on the backside of MPDP must be identical with the ID setting in MSCS to control
MPDP with a PC.

• If you do not have Com Port, you need to use an USB converter for RS-232C. Depending on
manufacturers or models, converters may cause malfunction.

PC

PC (MSCS) to control MPDP

RS-232C (Maximum 15m)

DVI connection
(Maximum 5m)

PC Connection
(Maximum 5m)

※ If you need longer

connection, please use DVI
boosters or DVI fiber-optic
cable.

[MPDP ID 1]

• ID switch must be set as ID 1
for one set use.

DOWN

UP

PDP

CO., LTD.

Made in Korea

• Model Name : OPM-4260

• Voltage : AC~100 - 240V

• Current : Max. 4A

• Frequency : 50/60Hz

• Serial No :

MPDP

FCC Verified : Class "A"

This device complies with the Part 15 of the FCC Rules.
Operation is subject to the following two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received,
including interference that may cause undesired operation.

To prevent electric shock,
Do not remove cover.
No user serviceable part inside Refer
servicing to qualified service personal.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

ID SELECT

FANSTBPWR ON

AUDIO/VIDEO
APPARATUS
E329824
42SS

VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

VCR

Video connection

(Maximum 5m)

OPM-4260 | OPM-4260R

Innitely Expandable

- 22 - - 23 -

4.2. Connection of Multiple MPDP

• Recommended maximum set connection for Multi setting is shown in table below.
If you need to connect more than described in the table, you have to use distributors.

• Image quality can be affected by cable or signal quality.

INPUT SOURCE Resolution Connection Remark

DVI 1600 x 1200 x 60Hz 6 sets HDCP Available

PC 1600 x 1200 x 60Hz 3 sets

VIDEO NTSC, PAL, SECAM 6 sets

RS-232C 30 sets ORION Cable Only

※ It is highly recommended to use RS-232C cable provided by ORION.If you want to use the other

RS-232C cable, it must be shielded.

※ Maximum use of RS-232C with Daisy Chain connection is 30 sets or less, if you need additional

connection, use New MFC.(Max 30sets/1 port)

ID SELECT VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

FANSTB PWR ON

ID SELECT VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

FANSTB PWR ON

ID SELECT VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

FANSTB PWR ON

ID SELECT VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

FANSTB PWR ON

ID SELECT VIDEO

IN OUT

DVI-D

IN OUT

RS-232C

IN OUT

PC

IN OUT

SVCLAN

FANSTB PWR ON

RS-232C

PC

VCR

DVI

PC

VIDEO

MPDP 1 MPDP 2

PC (MSCS) to control

MPDP

MPDP 3 MPDP 4 MPDP 5

OPM-4260 | OPM-4260R

Innitely Expandable

- 24 - - 25 -

4.3. Connection of Control Cable - In case of using MSCS

• Control signal transmission can be connected by 2 different methods.
(RS-232C or Ethernet)

• RS-232C and Ethernet connection cannot be used simultaneously.

4.3.1. Connection of RS-232C Cable

• Maximum use of RS-232C with Daisy Chain connection is 30 sets or less, if you need
additional connection, use New MFC.(Max 30sets/1 port)

4.3.2. Connection of Ethernet Cable

• In case of Ethernet connection, the control PC should be connected to one of MPDP sets with
Ethernet cable. For the connection between the MPDP sets, they should be connected with
RS-232C cables.

ID 1

ID 7

ID 2

ID 5ID 4

ID 8

ID 3

ID 6

ID 9

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C control PC

RS-232C

ID 1

ID 7

ID 2

ID 5ID 4

ID 8

ID 3

ID 6

ID 9

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

LAN

LAN

LAN

LAN

LAN

LAN

LAN

LAN

LAN

Ethernet control PC

HUB or Router

(Wireless & Cable)

LAN Cable

(Direct Cable)

LAN Cable

(Direct Cable)

LAN Cable

(Cross Cable)

OPM-4260 | OPM-4260R

Innitely Expandable

※ It is recommended to install New

MFC near to MPDP sets.

※ It is recommended to install New

MFC near to MPDP sets.

- 26 - - 27 -

4.4. Connection of Control Cable - In case of using the other control program
besides MSCS

※

If you use the other screen control program besides MSCS, the signal cable
must be connected via MFC (Multi- Function Controller) of ORION.

• Control signal transmission can be connected by 2 different methods. (RS-232C or Ethernet)

• RS-232C and Ethernet connection cannot be used simultaneously.

4.4.1. Connection of RS-232C Cable

• The RS-232C signal cable must be connected via MFC.

• Maximum use of RS-232C with Daisy Chain connection is 30 sets or less, if you need additional
connection, use New MFC.(Max 30sets/1 port)

4.4.2. Connection of Ethernet Cable

• If you want to control MPDP sets with Ethernet, PC and MFC can be connected with Ethernet
cable and between MFC and the first MPDP set and between the other MPDP sets should be
connected with RS-232C cable.

ID 1

ID 7

ID 2

ID 5ID 4

ID 8

ID 3

ID 6

ID 9

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C control PC

RS-232C

New MFC

ID 1

ID 7

ID 2

ID 5ID 4

ID 8

ID 3

ID 6

ID 9

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

RS-232C

IN OUT

LAN

LAN

LAN

LAN

LAN

LAN

LAN

LAN

LAN

Ethernet control PC

New MFC

RS-232C

HUB or Router

(Wireless & Cable)

LAN Cable

(Direct Cable)

LAN Cable

(Cross Cable)

OPM-4260 | OPM-4260R

Innitely Expandable