Orion OLS-32, OLS-40, OLS-70, OLS-55, OLS-46 User Manual

OLS-32/40/46/55/70/8201TGB/P

1 페이지 3/30/2012

1 of 36

Ver. 1.0 E

OLS-32/40/46/55/70/8201TGB/P

User’s Guide

OLS-32/40/46/55/70/8201TGB/P

2 페이지 3/30/2012

2 of 36

CONTENTS

 Safety Instructions ------------------------------------------------------------------- 3-7.

 Introduction -------------------------------------------------------------------------- 8-10.

 SICP ----------------------------------------------------------------------------------- 11-17.

 Remote control ------------------------------------------------------------------------ 18.

 Viewing the Menus ---------------------------------------------------------------- 19-30.

 Specifications ------------------------------------------------------------------------ 31-34.

OLS-32/40/46/55/70/8201TGB/P

3 페이지 3/30/2012

3 of 36

Safety Instructions

 Do not use a damaged or loose plug.

 This may cause electric shock or fire.

 Do not pull the plug out by the wire nor touch the plug with wet hands.

 This may cause electric shock or fire.

 Use only a properly grounded plug and receptacle.

 An improper ground may cause electric shock or equipment damage.

 Insert the power plug firmly so that it does not come loose.

 A bad connection may cause fire.

 Do not excessively bend the plug and wire nor place heavy objects

upon them, which could cause damage.

 This may cause electric shock or fire.

 Do not connect too many extension cords or plugs to one outlet.

 This may cause fire.

OLS-32/40/46/55/70/8201TGB/P

4 페이지 3/30/2012

4 of 36

 Do not disconnect the power cord while using the LCD Display.

 A surge may be caused by the separation and may damage the

LCD Display.

 Do not use the power cord when the connector or plug is dusty.

 If the connector or plug of the power cord is dusty,

clean it with a dry cloth.

 Using the power cord with a dusty plug or connector may cause

electric shock or fire.

 Do not drop the LCD Display when moving it.

This may cause damage to the product or the person carrying it.

 Keep any flammable objects such as candles, insecticides or

cigarettes away from the product.

 Otherwise, this may cause fire.

 Keep any heating devices away from the power cable.

 A melted coating may cause electric shock or fire.

 Put down the LCD Display carefully.

 Failing to do so may damage the LCD Display.

OLS-32/40/46/55/70/8201TGB/P

5 페이지 3/30/2012

5 of 36

 Do not place the LCD Display face down.

 This may damage the TFT-LCD surface.

 The installation of the bracket must be done by a qualified

professional.

 Installing the bracket by unqualified personnel may result in injury.
 Always use the mounting device specified in the owner's manual.

 When installing the product, make sure to keep it away from the wall

(more than 10 cm / 4 inches) for ventilation purposes.

 Poor ventilation may cause an increase in the internal temperature

of the product, resulting in a shortened component life and degraded
performance.

 Do not spray water or detergent directly onto the LCD Display.

This may cause damage, electric shock or fire.

.

 Keep the product away from places exposed to oil, smoke or

moisture; do not install inside a vehicle.

 This may cause a malfunction, electric shock or fire.
 In particular, avoid operating the LCD Display near water or outdoors

Where the LCD Display could be exposed to snow or rain.

 Disconnect the plug from the outlet during storms or lightning or if

it is not used for a long period of time.

 Failure to do so may cause electric shock or fire.

OLS-32/40/46/55/70/8201TGB/P

6 페이지 3/30/2012

6 of 36

 Do not install the product on an unstable, uneven surtace or a

location prone to vibrations.

 Dropping the product may cause damage to the product or the

person carrying it.

Using the product in a location prone to vibrations mayshorten

the lifetime of the product or may cause the product to

catch fire.

 When removing batteries from the remote control, be careful that

they are not swallowed by children. keep the batteries out of
children's reach.

 If the batteries are swallowed, see a doctor immediately.

 When replacing batteries, place the batteries in the correct +/-

polarity position as indicated on the battery holder.

 The incorrect polarity may cause a battery to break or leak and

Cause fire, injury, or contamination (damage).

 Use only specified standard batteries. Do not use new

and used batteries together.

`  This may cause a battery to break or leak and may cause

fire, injury, or contamination (damage).

 The batteries (and rechargeable batteries) is not ordinary refuse

and must be returned for recycling purposes.
The customer is responsible for returning the used or
rechargeable batteries for recycling purposes as the consumer.

 The customer can return used or rechargeable batteries to a nearby

Public recycling center or to a store selling the same type of

the battery or rechargeable battery.

OLS-32/40/46/55/70/8201TGB/P

7 페이지 3/30/2012

7 of 36

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such
as vases, are placed on the apparatus.

16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from
the AC receptacle.

17. The mains plug of the power supply cord shall remain readily operable.

18. An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective
earthing connection.

Note: Prolonged use of headphones at a high volume may cause health damage on your ears.

The lightning flash with arrowhead symbol within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

OLS-32/40/46/55/70/8201TGB/P

8 페이지 3/30/2012

8 of 36

Introduction

LCD Display

Manual

User Manual CD

Cable

RGB Cable AC Power Cable

HDMI Cable (Option)

Other

Remote Control Batteries (AAA X 2)

OLS-32/40/46/55/70/8201TGB/P

9 페이지 3/30/2012

9 of 36

Front

1. IR

- Aim the remote control towards this spot on the LCD Display.

2. LED

- LCD Power Status display(On : BLUE / Off : RED)

3. OSD KEY Input(Power / Menu / Source / Left / Right / Up / Down)
a) Power : Turns the LCD Display On/ Off.
b) Menu : Displays the main On-Screen menu.
c) Source : Select Input Source

- HDMI PC COMPONENT AV

d) Left/Right : Moves from one menu item to another horizontally or adjusts selected menu

values. Adjusts the audio volume.

e) Up/Down : Moves from one menu item to another vertically or adjusts selected menu values.

1 2 a b c

d

e

3

OLS-32/40/46/55/70/8201TGB/P

10 페이지 3/30/2012

10 of 36

Rear

1. AC Power S/W On/Off

2. AC Power In (100V ~ 240V)

3. HDMI Input

4. DVI(HDMI Jack) Output

5. PC Input

6. RS-232 Output

7. RS-232 Input

8. Component(Input)

9. Component(Output)

10. AV Input

11. AV Output

12. PC Sound Input

13. Component Sound Input

14. AV Sound Input

3 4 5 6 7 8 9

10

11

12

13

14 2 1

OLS-32/40/46/55/70/8201TGB/P

11 페이지 3/30/2012

11 of 36

SICP (Serial Interface Communication Protocol)

This document defines all the command and messages exchanged between the
Master (a PC or the other controller) and the Slave (the displays).
It also describes the ways to send or read the commands or the messages.

1. Protocol definition

SICP stands for “Serial Interface Communication Protocol”.
The protocol is specifically designed to allow data communication in half duplex multi-point environments,

but it can also be used for half duplex point-to-point RS‑232C communication.

2. Communication characteristics

A half duplex communication is implemented starting from the concept of a master-slave structure, where
the display is supposed to be the slave.
The first action is always taken by the master, which can be either a PC or any controlling device (acting
as server) interfaced to the monitor. After sending a command or a request in the appropriate format the
master receives from the slave an acknowledgement, which tells the transmitter whether the command is
not valid (or not executable, anyway) or it is accepted. In case of a request, the requested information is
sent back and it becomes the acknowledgement by itself.

3. How to connect a external equipment

Female Pin number Male Pin number
2 <------------------------------------------------------> 2
3 <------------------------------------------------------> 3
5 <------------------------------------------------------> 5

4. Hardware Protocol

Baud rate : 9600 bps
Data bits : 8 bit
Parity bits : None
Stop bits : 1 bit
Handshake : None

5. Transmission Formats

This is the format that the computer will send to the display to execute commands .
The format for this command transmission is as follows:
( total 13 byte )
ex) <STX>001PWRWOFF0<ETX> ( Set ID : 1 , Power Off Send )

STX

ID1

ID2

ID3

CM1

CM2

CM3

R/W

DA1

DA2

DA3

IND

ETX

0x0f 0 0 1 P W R W O F F 0 0x0d

Hex

ASCII (capital letter)

Hex

- STX : Start of Text ( 0x0f )

- ID1 ~ ID3 : Set ID ( 001~100 )

- CM1 ~ CM3 : Command ( PWR, MIN, MUT,RML,KPL…… )

- R/W : Read/Write

- DA1 ~ DA3 : Data ( Values )

- IND : Index

- ETX : End of Text ( 0x0d )