Page 1
OLS-32/40/46/55/70/8201TGB/P
1 페이지 3/30/2012
1 of 36
Ver. 1.0 E
OLS-32/40/46/55/70/8201TGB/P
User’s Guide
Page 2
OLS-32/40/46/55/70/8201TGB/P
2 페이지 3/30/2012
2 of 36
CONTENTS
Safety Instructions ------------------------------------------------------------------- 3-7.
Introduction -------------------------------------------------------------------------- 8-10.
SICP ----------------------------------------------------------------------------------- 11-17.
Remote control ------------------------------------------------------------------------ 18.
Viewing the Menus ---------------------------------------------------------------- 19-30.
Specifications ------------------------------------------------------------------------ 31-34.
Page 3
OLS-32/40/46/55/70/8201TGB/P
3 페이지 3/30/2012
3 of 36
Safety Instructions
Do not use a damaged or loose plug.
This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
This may cause electric shock or fire.
Use only a properly grounded plug and receptacle.
An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose.
A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet.
This may cause fire.
Page 4
OLS-32/40/46/55/70/8201TGB/P
4 페이지 3/30/2012
4 of 36
Do not disconnect the power cord while using the LCD Display.
A surge may be caused by the separation and may damage the
LCD Display.
Do not use the power cord when the connector or plug is dusty.
If the connector or plug of the power cord is dusty,
clean it with a dry cloth.
Using the power cord with a dusty plug or connector may cause
electric shock or fire.
Do not drop the LCD Display when moving it.
This may cause damage to the product or the person carrying it.
Keep any flammable objects such as candles, insecticides or
cigarettes away from the product.
Otherwise, this may cause fire.
Keep any heating devices away from the power cable.
A melted coating may cause electric shock or fire.
Put down the LCD Display carefully.
Failing to do so may damage the LCD Display.
Page 5
OLS-32/40/46/55/70/8201TGB/P
5 페이지 3/30/2012
5 of 36
Do not place the LCD Display face down.
This may damage the TFT-LCD surface.
The installation of the bracket must be done by a qualified
professional.
Installing the bracket by unqualified personnel may result in injury.
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall
(more than 10 cm / 4 inches) for ventilation purposes.
Poor ventilation may cause an increase in the internal temperature
of the product, resulting in a shortened component life and degraded
performance.
Do not spray water or detergent directly onto the LCD Display.
This may cause damage, electric shock or fire.
.
Keep the product away from places exposed to oil, smoke or
moisture; do not install inside a vehicle.
This may cause a malfunction, electric shock or fire.
In particular, avoid operating the LCD Display near water or outdoors
Where the LCD Display could be exposed to snow or rain.
Disconnect the plug from the outlet during storms or lightning or if
it is not used for a long period of time.
Failure to do so may cause electric shock or fire.
Page 6
OLS-32/40/46/55/70/8201TGB/P
6 페이지 3/30/2012
6 of 36
Do not install the product on an unstable, uneven surtace or a
location prone to vibrations.
Dropping the product may cause damage to the product or the
person carrying it.
Using the product in a location prone to vibrations mayshorten
the lifetime of the product or may cause the product to
catch fire.
When removing batteries from the remote control, be careful that
they are not swallowed by children. keep the batteries out of
children's reach.
If the batteries are swallowed, see a doctor immediately.
When replacing batteries, place the batteries in the correct +/-
polarity position as indicated on the battery holder.
The incorrect polarity may cause a battery to break or leak and
Cause fire, injury, or contamination (damage).
Use only specified standard batteries. Do not use new
and used batteries together.
` This may cause a battery to break or leak and may cause
fire, injury, or contamination (damage).
The batteries (and rechargeable batteries) is not ordinary refuse
and must be returned for recycling purposes.
The customer is responsible for returning the used or
rechargeable batteries for recycling purposes as the consumer.
The customer can return used or rechargeable batteries to a nearby
Public recycling center or to a store selling the same type of
the battery or rechargeable battery.
Page 7
OLS-32/40/46/55/70/8201TGB/P
7 페이지 3/30/2012
7 of 36
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such
as vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from
the AC receptacle.
17. The mains plug of the power supply cord shall remain readily operable.
18. An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective
earthing connection.
Note: Prolonged use of headphones at a high volume may cause health damage on your ears.
The lightning flash with arrowhead symbol within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
Page 8
OLS-32/40/46/55/70/8201TGB/P
8 페이지 3/30/2012
8 of 36
Introduction
LCD Display
Manual
User Manual CD
Cable
RGB Cable AC Power Cable
HDMI Cable (Option)
Other
Remote Control Batteries (AAA X 2)
Page 9
OLS-32/40/46/55/70/8201TGB/P
9 페이지 3/30/2012
9 of 36
Front
1. IR
- Aim the remote control towards this spot on the LCD Display.
2. LED
- LCD Power Status display(On : BLUE / Off : RED)
3. OSD KEY Input(Power / Menu / Source / Left / Right / Up / Down)
a) Power : Turns the LCD Display On/ Off.
b) Menu : Displays the main On-Screen menu.
c) Source : Select Input Source
- HDMI PC COMPONENT AV
d) Left/Right : Moves from one menu item to another horizontally or adjusts selected menu
values. Adjusts the audio volume.
e) Up/Down : Moves from one menu item to another vertically or adjusts selected menu values.
1 2 a b c
d
e
3
Page 10
OLS-32/40/46/55/70/8201TGB/P
10 페이지 3/30/2012
10 of 36
Rear
1. AC Power S/W On/Off
2. AC Power In (100V ~ 240V)
3. HDMI Input
4. DVI(HDMI Jack) Output
5. PC Input
6. RS-232 Output
7. RS-232 Input
8. Component(Input)
9. Component(Output)
10. AV Input
11. AV Output
12. PC Sound Input
13. Component Sound Input
14. AV Sound Input
3 4 5 6 7 8 9
10
11
12
13
14 2 1
Page 11
OLS-32/40/46/55/70/8201TGB/P
11 페이지 3/30/2012
11 of 36
SICP (Serial Interface Communication Protocol)
This document defines all the command and messages exchanged between the
Master (a PC or the other controller) and the Slave (the displays).
It also describes the ways to send or read the commands or the messages.
1. Protocol definition
SICP stands for “Serial Interface Communication Protocol”.
The protocol is specifically designed to allow data communication in half duplex multi-point environments,
but it can also be used for half duplex point-to-point RS‑232C communication.
2. Communication characteristics
A half duplex communication is implemented starting from the concept of a master-slave structure, where
the display is supposed to be the slave.
The first action is always taken by the master, which can be either a PC or any controlling device (acting
as server) interfaced to the monitor. After sending a command or a request in the appropriate format the
master receives from the slave an acknowledgement, which tells the transmitter whether the command is
not valid (or not executable, anyway) or it is accepted. In case of a request, the requested information is
sent back and it becomes the acknowledgement by itself.
3. How to connect a external equipment
Female Pin number Male Pin number
2 <------------------------------------------------------> 2
3 <------------------------------------------------------> 3
5 <------------------------------------------------------> 5
4. Hardware Protocol
Baud rate : 9600 bps
Data bits : 8 bit
Parity bits : None
Stop bits : 1 bit
Handshake : None
5. Transmission Formats
This is the format that the computer will send to the display to execute commands .
The format for this command transmission is as follows:
( total 13 byte )
ex) <STX>001PWRWOFF0<ETX> ( Set ID : 1 , Power Off Send )
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f 0 0 1 P W R W O F F 0 0x0d
Hex
ASCII (capital letter)
Hex
- STX : Start of Text ( 0x0f )
- ID1 ~ ID3 : Set ID ( 001~100 )
- CM1 ~ CM3 : Command ( PWR, MIN, MUT,RML,KPL…… )
- R/W : Read/Write
- DA1 ~ DA3 : Data ( Values )
- IND : Index
- ETX : End of Text ( 0x0d )
Page 12
OLS-32/40/46/55/70/8201TGB/P
12 페이지 3/30/2012
12 of 36
6. OK Acknowledgement
The acknowledgement will be sent by the display to the computer to verify that the command has been
successfully received and executed. This format for this acknowledgement is as follows:
ex) <STX>001PWR#OFF#<ETX> ( Set ID : 1 , Power Off Acknowledgement )
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f 0 0 1 P W R # O F F # 0x0d
Hex
ASCII (capital letter)
Hex
7. Error Acknowledgement
The Error Values will be sent by the display to the computer to verify that the command has been
successfully received and executed.
This format for this Error Values is as follows:
ex) <STX>001PWRERROR<ETX> ( Set ID : 1 , Power Off Error )
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f 0 0 1 P W R
E R R O R
0x0d
Hex
ASCII (capital letter)
Hex
8. Command List
♦ Mute On/Off (MUT)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
M U T W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID ( “001” ~ “100” )
- DA1 ~ DA3 : “ON” ( Mute On )
“OFF” ( Mute Off )
Ex) <STX>001MUTW-ON0<ETX> ( Mute On )
Acknowledge => <STX>001MUT#-ON#<ETX>
♦ Power On/Off (PWR)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
P W R W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “ON” : Power On
“OFF” : Power Off
Ex) <STX>001PWRWOFF0<ETX> ( Power Off )
Acknowledge => <STX>001PWR#OFF#<ETX>
Page 13
OLS-32/40/46/55/70/8201TGB/P
13 페이지 3/30/2012
13 of 36
♦ Source Change (MIN)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
M I N W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “DVI” : DVI(HDMI)
“COM” : Component
“PC” : PC(D-SUB)
“AV” : AV(Composite)
“SAV” : S-Video
Ex) <STX>001MINWDVI0<ETX> ( Source DVI )
Acknowledge => <STX>001MIN#DVI#<ETX>
♦ Virtual Remote Control (RMT)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
R M T W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “MEN” (Menu)
“SOU” (Source)
“LEF” (Left & Volume-)
“RIG” (Right & Volume+)
“ENT” (Enter)
“UP” (Up)
“DOW” (Down)
“EXI” (Exit)
Ex) <STX>001RMTWSOU0<ETX> ( Remote Source Button)
Acknowledge => <STX>001RMT#SOU#<ETX>
♦ PC Auto Adjust (AUT)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
A U T W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “PC”
Ex) <STX>001AUTW-PC0<ETX> ( Remote Source Button)
Acknowledge => <STX>001AUT#-PC#<ETX>
Page 14
OLS-32/40/46/55/70/8201TGB/P
14 페이지 3/30/2012
14 of 36
1. Introduction
This manual booklet describes how to manage and utilize the product (Multivision set) through remote
control by RS232 protocol. This will introduce SICP V2.08M (Software that enables you to control the
Multivision) and various applications will be possible with this software. As per different way of customizing,
the functions and specifications of each product may vary.
2. Installing SICP V2.08M
Run the file named “SICP208MSetupUS.exe” and follow the instruction below.
If you have SICP program installed previously, delete the previous one and re-install the new one.
Press “Next”
Select the folder you wish to save the file in. Press “Install” if you are ok with the designated folder.
Page 15
OLS-32/40/46/55/70/8201TGB/P
15 페이지 3/30/2012
15 of 36
Wait until the installation is complete.
Once installation is complete, Go to “Start”Menu -> Programs -> SICP V2.08M to run the program.
Page 16
OLS-32/40/46/55/70/8201TGB/P
16 페이지 3/30/2012
16 of 36
3. Running SICP V2.08M and Structure
Go to “Start” Menu -> Programs -> SICP V2.08M to run the program.
① Progress Bar : Shows the status of RS232 communication
② Communication : Select the Port connected to the PC
③ Set ID : Shows the Set ID you can control
④ Control Button : Set of control buttons
⑤ Control Button : Set of control Remocon buttons
1 2 3 4 5
Page 17
OLS-32/40/46/55/70/8201TGB/P
17 페이지 3/30/2012
17 of 36
4. Connect & Disconnect
- You can connect RS232 input and control PC using RS232 Cable.
- Select the Port you can connect to your PC (refer to ② in the image above) and press connect button.
If connected properly, the lamp will be turned to BLUE (from RED). If not connected properly, the following
message will appear.
Unable to open serial port : The port may not be available in your PC or another program may be running
under this port.
Cannot connect with Easy DiD System : RS232 Cable may not be connected properly or Set ID may be
incorrect. Re-check on Set ID.
5. DID Set Control
1) Basic Control
- Select Control Tab
Power Control : Turn the Set On/Off
Source Control : Select Source
Sound Mute : Turn the Mute On/Off
PC Auto Adjust :
2) Virtual Remocon
- Select Remocon Tab
- This virtual remote controller controls the set
through RS232.
Page 18
OLS-32/40/46/55/70/8201TGB/P
18 페이지 3/30/2012
18 of 36
Remote control
1. POWER : Turns the LCD Display On and Off
2. UP : Control the UP cursor in the menu
3, LEFT : Control the LEFT cursor in the menu
4, RIGHT : Control the RIGHT cursor in the menu
5, ENTER : Control the ENTER cursor in the menu
6, DOWN : Control the DOWN cursor in the menu
7. MENU : Displays the main On-Screen menu
8. SOURCE : Select Input Source
- HDMI PC COMPONENT AV
9. EXIT : Exit the On-Screen menu
2 1 3
4
5
7
6
8
9
Page 19
OLS-32/40/46/55/70/8201TGB/P
19 페이지 3/30/2012
19 of 36
Viewing the Menus
◆ Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Setup and PIP.
Changing the Picture Standard
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Picture, then press the ENTER button.
3. Press the ENTER button twice.
4. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
➢ The settings values may vary depending on the input source.
(ex. AV, Component, PC, or HDMI)
5. Press the EXIT button to exit.
Page 20
OLS-32/40/46/55/70/8201TGB/P
20 페이지 3/30/2012
20 of 36
Customizing the Picture Settings
Your DID Set has several setting options that allow you to control the picture quality.
1. Press the MENU button to display the menu.
2. Press the ENTER button.
3. Press the ▲ or ▼ button to select Custom, then press the ENTER button.
4. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
5. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
6. When you are satisfied with your setting, press the ENTER button.
7. Press the EXIT button to exit.
◆ Brightness – Contrast– Color – Tint –Sharpness (Tint NTSC only)
Press the ◀ or ▶ button until you reach the optimal setting.
◆Brightness: It adjusts the brightness of the image.
◆Contrast: It adjusts the contrast of image.
◆Color: It adjusts the intensity of the color.
◆Tint: It adjusts the natural tint of the image.
◆Sharpness: It adjusts the clarity of the image.
◆Color Tone: Cool2/Cool1/Normal/Warm1/Warm2
Page 21
OLS-32/40/46/55/70/8201TGB/P
21 페이지 3/30/2012
21 of 36
◆Cool 1: This results in a blue tone.
◆Cool 2: This results in a more blue tone.
◆Normal: This is standard color setting.
◆Warm1: This results in a reddish tone.
◆Warm2: This results in a more reddish tone.
Selecting the Picture Size
You can select the picture size which best corresponds to your viewing requirements.
.
1. Press the MENU button to display the menu.
2. Press the ENTER button.
3. Press the ▲ or ▼ button to select Size, then press the ENTER button.
4. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
5. Press the EXIT button to exit.
Page 22
OLS-32/40/46/55/70/8201TGB/P
22 페이지 3/30/2012
22 of 36
Selecting the Multi Edge Adj.Mode
1. Press the MENU button to display the menu.
2. Press the ENTER button.
3. Press the ▲ or ▼ button to select Multi Edge Adj.Mode, then press the ENTER button.
4. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
5. Press the EXIT button to exit.
※ Adjust Horizontal/ Vertical Edge Gap
◆Off: This Adjust Horizontal/ Vertical Edge Gap Off
◆Auto: This Adjust Horizontal/ Vertical Edge Gap Normal.
Page 23
OLS-32/40/46/55/70/8201TGB/P
23 페이지 3/30/2012
23 of 36
◆Top Left: This Adjust Horizontal(Left) / Vertical(Top) Edge Gap.
◆Center: This Adjust Horizontal(Center) / Vertical(Center) Edge Gap..
◆Bottom Right: This Adjust Horizontal(Right) / Vertical(Bottom) Edge Gap.
Page 24
OLS-32/40/46/55/70/8201TGB/P
24 페이지 3/30/2012
24 of 36
Viewing the Picture in Picture (PIP) (Available in PC mode)
You can display a sub picture within the main picture of PC. In this way you can watch monitor the video input from any
connected devices while watching PC.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select PIP, then press the ENTER button.
3. Press the ▲ or ▼ button to select On, then press the ENTER button.
4. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
5. When you are satisfied with your setting, press the ENTER button.
6. Press the EXIT button to exit.
◆ Input Source: HDMI / PC / Component / AV
You can select a source of the sub-picture.
Page 25
OLS-32/40/46/55/70/8201TGB/P
25 페이지 3/30/2012
25 of 36
You can select a source size of the sub-picture.
◆ Position:
You can select a source position of the sub-picture.
◆ Swap
You can select the main screen and the sub screen will swap.
Page 26
OLS-32/40/46/55/70/8201TGB/P
26 페이지 3/30/2012
26 of 36
◆ Sound Select.
You can select the sound of the sub screen can be selected when PIP is being displayed.
Reset.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Setup, then press the ENTER button.
3. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
4. When you are satisfied with your setting, press the ENTER button.
◆ Reset: You can return to the factory defaults settings.
Page 27
OLS-32/40/46/55/70/8201TGB/P
27 페이지 3/30/2012
27 of 36
Time Features.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Setup, then press the ENTER button.
3. Press the ▲ or ▼ button to select Timer, then press the ENTER button.
4. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
5. When you are satisfied with your setting, press the ENTER button.
6. Press the EXIT button to exit.
-Attention : If you off the AC Power then Clear time set value
Language.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Setup, then press the ENTER button.
3. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
4. When you are satisfied with your setting, press the ENTER button.
5. Press the EXIT button to exit.
Page 28
OLS-32/40/46/55/70/8201TGB/P
28 페이지 3/30/2012
28 of 36
OSD Tone.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Setup, then press the ENTER button.
3. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
4. When you are satisfied with your setting, press the ENTER button.
5. Press the EXIT button to exit.
Advanced.
Page 29
OLS-32/40/46/55/70/8201TGB/P
29 페이지 3/30/2012
29 of 36
Dimming.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Setup->Dimming then press the ENTER button.
3. Select the required option by pressing the ▲ or ▼ button
- Auto Dimming : On or Off : If want Auto Control the Dimming by lux value then select On, or not Off
- Dim Level : If auto dimming off, you can adjust manual dimming.
- Max Dim. Ambient : For max Dimming value by this value
- Min Dim. Ambient : For min Dimming value by this value
- Ambient : Current ambient lux
* Lux sensor board should be set out side of front case. (Option)
4. Press the EXIT button to exit.
Page 30
OLS-32/40/46/55/70/8201TGB/P
30 페이지 3/30/2012
30 of 36
Heat control.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Setup->Heat Control then press the ENTER button.
3. Select the required option by pressing the ▲ or ▼ button
-Fan Control : Off/On/Auto : If you want always fan off then Off or always on then On or Auto control then Auto.
-Fan Active Temperature : Fan turn on point.
-Hysteresis : Fan turn on or off margin value.
-Temperature : Current temperature
4. Press the EXIT button to exit.
Page 31
OLS-32/40/46/55/70/8201TGB/P
31 페이지 3/30/2012
31 of 36
Specifications
OLS-3201TGB
Items
Specifications
32 inch
Display Size
32 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.51075(H) x 0. 51075 (V) mm
Resolution
1366 x 768 (WXGA)
Colors
8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio
4000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
760.0(H Typ) x 450.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 1A
Power Consumption
150W
OLS-4001TGB
Items
Specifications
40 inch
Display Size
40 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.461225(H) x 0. 461225 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio
4000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
952.0(H Typ) x 551.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 1A
Power Consumption
200W
Page 32
OLS-32/40/46/55/70/8201TGB/P
32 페이지 3/30/2012
32 of 36
OLS-4001TGP
Items
Specifications
40 inch
Display Size
40 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.46125(H) x 0. 46125 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
700cd/㎡ (Typ)
Contrast Ratio
3000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
911.7(H Typ) x 524.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 1A
Power Consumption
200W
OLS-4601TGB
Items
Specifications
46 inch
Display Size
46 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.53025(H) x 0. 53025 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio
4000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
1083.0(H Typ) x 627.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 1.5A
Power Consumption
260W
Page 33
OLS-32/40/46/55/70/8201TGB/P
33 페이지 3/30/2012
33 of 36
OLS-4601TGP
Items
Specifications
46 inch
Display Size
46 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.53025(H) x 0. 53025 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
700cd/㎡ (Typ)
Contrast Ratio
3000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
1018.08(H Typ) x 572.67V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 1.5A
Power Consumption
280W
OLS-5501TGB
Items
Specifications
55 inch
Display Size
55 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.21(H) x 0. 63 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio
4000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Haze 44%
Panel Size
1242.2(H Typ) x 713.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 2.5A
Power Consumption
310W
Page 34
OLS-32/40/46/55/70/8201TGB/P
34 페이지 3/30/2012
34 of 36
OLS-5501TGP
Items
Specifications
55 inch
Display Size
55 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.21(H) x 0. 63 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
700cd/㎡ (Typ)
Contrast Ratio
3000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Haze 44%
Panel Size
1242.2(H Typ) x 713.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 2.5A
Power Consumption
320W
OLS-7001TGB
Items
Specifications
70 inch
Display Size
70 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.807(H) x 0. 807 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio
3000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
952.0(H Typ) x 551.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 9.2A
Power Consumption
900W
Page 35
OLS-32/40/46/55/70/8201TGB/P
35 페이지 3/30/2012
35 of 36
OLS-7001TGP
Items
Specifications
70 inch
Display Size
70 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.807(H) x 0. 807 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
600cd/㎡ (Typ)
Contrast Ratio
2000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
952.0(H Typ) x 551.0(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 9.2A
Power Consumption
920W
OLS-8201TGB
Items
Specifications
82 inch
Display Size
82 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.9405(H) x 0. 9405 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio
3000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
1805.76(H Typ) x 1015.74(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 9.2A
Power Consumption
850W
Page 36
OLS-32/40/46/55/70/8201TGB/P
36 페이지 3/30/2012
36 of 36
OLS-8201TGP
Items
Specifications
82 inch
Display Size
82 Inch (16:9) : LCD / S-PVA TFT
Response Time
8 ms(Typ G to G)
Pixel Size
0.9405(H) x 0. 9405 (V) mm
Resolution
1920 x 1080 (WUXGA)
Colors
8 bit, 16.7M Colors
Brightness
600cd/㎡ (Typ)
Contrast Ratio
2000:1
View Angle
Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment
Hard coating(3H), Haze 44%
Panel Size
1805.76(H Typ) x 1015.74(V Typ)
POWER
AC Input
AC 100~240V~, 50/60Hz, 9.2A
Power Consumption
950W
Items
Specifications
Touch Screen
Resolution
16, 384*16, 384
Response Time (ms)
< 10ms
Glass
Thickness: 5mm
Weight (kg)
2
Interface
USB 1.1
Touch Intensity
Over 60,000,000
C drive by the EWF function is to protect the System file.
Add a program or file on the C drive, reboot and nevertheless addition will be deleted.
Remember to add the program or file, please work on the D drive.
Operating Temperature : 0℃ ~ 40℃.
Quality assurance : The warranty period is one year
※ This product can be changed to improve performance without notification.
The up contents not to notify can be changed.
HEAD OFFICE FACTORY : 257-6 GONGDAN-DONG, GUMI, GYEONGBUK, KOREA
TEL 82-54-460-5700 FAX : 82-54-461-3284
Loading...