Page 1
OLS-PGB/P Series
1 of 33
Ver. 1.0 E
OLS-PGB/P Series
User’s Guide
Page 2
OLS-PGB/P Series
2 of 33
CONTENTS
Safety Instructions ------------------------------------------------------------------- 3-7.
Introduction
-------------------------------------------------------------------------- 8-10.
Remote control ------------------------------------------------------------------------ 11.
Viewing the Menus ---------------------------------------------------------------- 12-26.
Specifications ----------------------------------------------------------------------- 27-32.
EWF -------------------------------------------------------------------------------------- 33.
Page 3
OLS-PGB/P Series
3 of 33
Safety Instructions
Do not use a damaged or loose plug.
This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
This may cause electric shock or fire.
Use only a properly grounded plug and receptacle.
An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose.
A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet.
This may cause fire.
Page 4
OLS-PGB/P Series
4 of 33
Do not disconnect the power cord while using the LCD Display.
A surge may be caused by the separation and may damage the
LCD Display.
Do not use the power cord when the connector or plug is dusty.
If the connector or plug of the power cord is dusty,
clean it with a dry cloth.
Using the power cord with a dusty plug or connector may cause
electric shock or fire.
Do not drop the LCD Display when moving it.
This may cause damage to the product or the person carrying it.
Keep any flammable objects such as candles, insecticides or
cigarettes away from the product.
Otherwise, this may cause fire.
Keep any heating devices away from the power cable.
A melted coating may cause electric shock or fire.
Put down the LCD Display carefully.
Failing to do so may damage the LCD Display.
Page 5
OLS-PGB/P Series
5 of 33
Do not place the LCD Display face down.
This may damage the TFT-LCD surface.
The installation of the bracket must be done by a qualified
professional.
Installing the bracket by unqualified personnel may result in injury.
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall
(more than 10 cm / 4 inches) for ventilation purposes.
Poor ventilation may cause an increase in the internal temperature
of the product, resulting in a shortened component life and degraded
performance.
Do not spray water or detergent directly onto the LCD Display.
This may cause damage, electric shock or fire
.
.
Keep the product away from places exposed to oil, smoke or
moisture; do not install inside a vehicle.
This may cause a malfunction, electric shock or fire.
In particular, avoid operating the LCD Display near water or outdoors
Where the LCD Display could be exposed to snow or rain.
Disconnect the plug from the outlet during storms or lightning or if
it is not used for a long period of time.
Failure to do so may cause electric shock or fire.
Page 6
OLS-PGB/P Series
6 of 33
Do not install the product on an unstable, uneven surtace or a
location prone to vibrations.
Dropping the product may cause damage to the product or the
person carrying it.
Using the product in a location prone to vibrations mayshorten
the lifetime of the product or may cause the product to
catch fire.
When removing batteries from the remote control, be careful that
they are not swallowed by children. keep the batteries out of
children's reach.
If the batteries are swallowed, see a doctor immediately.
When replacing batteries, place the batteries in the correct +/-
polarity position as indicated on the battery holder.
The incorrect polarity may cause a battery to break or leak and
Cause fire, injury, or contamination (damage).
Use only specified standard batteries. Do not use new
and used batteries together.
`
This may cause a battery to break or leak and may cause
fire, injury, or contamination (damage).
The batteries (and rechargeable batteries) is not ordinary refuse
and must be returned for recycling purposes.
The customer is responsible for returning the used or
rechargeable batteries for recycling purposes as the consumer.
The customer can return used or rechargeable batteries to a nearby
Public recycling center or to a store selling the same type of
the battery or rechargeable battery.
Page 7
OLS-PGB/P Series
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.
Do not use this apparatus near water.
6. Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordanc
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for yo
outlet, consult an electrician for replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they ex
it from the apparatus
11.
Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart
injury from tip-over.
13.
Unplug this apparatus during lightning storms or when unused for long periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged
in any way, such as power
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15.
Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such
as vases, are placed on the apparatus.
16.
To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from
the AC receptacle.
17.
The mains plug of the power supply cord shall remain readily operable.
18.
An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective
earthing connection.
Note: Prolonged use of headphones at a high volu
The lightning flash with arrowhead symbol within an equilateral triangle, is
intended to alert the user to the presence of
within the product's enclosure
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in
e with the manufacturer’s instructions
-
type plug. A polarized plug has two
ur safety. If the provided plug does not fit into your
/apparatus combination to avoid
-
supply cord or plug is damaged, liquid has been spilled or objects
me may cause health damage on your ears.
uninsulated "dangerous voltage
that may be of sufficient magnitude to
the literature accompanying the product.
7 of 33
.
"
Page 8
OLS-PGB/P Series
8 of 33
Introduction
LCD Display
Manual
User Manual CD
Cable
AC Power Cable
HDMI Cable (Option)
Other
Remote Control
Batteries (AAA X 2)
Page 9
OLS-PGB/P Series
9 of 33
Front
1. IR
-
Aim the remote control towards this spot on the LCD Display.
2. LED
- LCD Power Status display(On : BLUE / Off : RED)
3. OSD KEY Input(Power / Menu / Source / Left / Right / Up / Down)
a) Power : Turns the LCD Display On/ Off.
b) Menu :
Displays the main On-Screen menu
.
c)
Source :
Select Input Source
- DVI PC
d) Left/Right : Moves from one menu item to another horizontally or adjusts selected menu
values. Adjusts the audio volume.
e) Up/Down :
Moves from one menu item to another vertically or adjusts selected menu values.
1
2 a b c d e 3
Page 10
OLS-PGB/P Series
10 of 33
Rear
1. AC Power S/W On/Off.
2. AC Power In.(100V ~ 240V)
3. HDMI Out.
4. VGA Out.
5. DVI Out.
6. ESATA (2EA).
7. PS/2 Keyboard.
8. USB2.0 (6EA)
9. RJ45 LAN.
10. Audio Port.(Line-In / Line-Out / MIC-In)
11. HDD.
3
4
5
6
7
8
9
10
11
2
1
Page 11
OLS-PGB/P Series
11 of 33
Remote control
1. POWER: Turns the LCD Display On and Off & PC Power On and Off.
2. UP : Control the UP cursor in the menu
3, LEFT : Control the LEFT cursor in the menu
4, RIGHT : Control the RIGHT cursor in the menu
5, ENTER : Control the ENTER cursor in the menu
6, DOWN : Control the DOWN cursor in the menu
7. MENU: Displays the main On-Screen menu
8. SOURCE : Select Input Source
- DVI PC
9. EXIT: Exit the On-Screen menu
2
1
3
4
5 7 6 8
9
Page 12
OLS-PGB/P Series
12 of 33
Viewing the Menus
Press the MENU button.
The main menu is displayed on the screen.
Its left side has five Text: Color, Image Setting, Position , OSD Meuu, Language, Misc., Audio and Exit.
Changing the Color Standard
Your television has several setting options that allow you to control the picture quality.
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Color, then press the ENTER button.
Page 13
OLS-PGB/P Series
13 of 33
3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
Contrast –Brightness– Color Adjust –Color Temp –Back
Adjusts the Contrast and Brightness.
3-1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-2 Press the or button until you reach the optimal setting.
Page 14
OLS-PGB/P Series
14 of 33
Adjust the Color.
: It adjusts the intensity of the color.
3-3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-4.Select the required mode by pressing the or button, then press the ENTER button.
Red –Green– Blue
3-5. Press the or button until you reach the optimal setting.
Page 15
OLS-PGB/P Series
15 of 33
Adjusts the Color Temp.
3-6. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-7. Press the or button until you reach the optimal setting.
9300 – 6500 – 5800 - sRGB - USER
9300: This results in a blue tone.
6500: This results in a reddish tone.
5800: This results in a more reddish tone.
sRGB: This is standard color setting.
USER: This is user color setting.
4. Press the EXIT button or Back Select to exit.
Changing the Image Standard
Page 16
OLS-PGB/P Series
16 of 33
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Image Setting, then press the ENTER button.
3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
Clock –Phase– Gamma(not available) –Sharpness –Back
Adjusts the Clock.
3-1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-2 Press the or button until you reach the optimal setting.
Page 17
OLS-PGB/P Series
17 of 33
Adjusts the Phase.
3-3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-4. Press the or button until you reach the optimal setting.
Adjusts the Sharpness.
3-5. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-6. Press the or button until you reach the optimal setting.
4. Press the EXIT button or Back Select to exit.
Page 18
OLS-PGB/P Series
18 of 33
Changing the Position Standard
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Position, then press the ENTER button.
3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
H.Position –V.Position –Back
Page 19
OLS-PGB/P Series
19 of 33
Adjusts the H.position and V.Position.
3-1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-2 Press the or button until you reach the optimal setting.
4. Press the EXIT button or Back Select to exit.
Changing the OSD Menu Standard
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select OSD Menu, then press the ENTER button.
Page 20
OLS-PGB/P Series
20 of 33
3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
OSD H.Pos – OSD V.Pos – OSD Time –Back
Adjusts the
OSD H.Pos
and
OSD V.Pos.
3-1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-2 Press the or button until you reach the optimal setting.
Page 21
OLS-PGB/P Series
21 of 33
Adjusts the
OSD Time.
3-3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
3-4. Press the or button until you reach the optimal setting.
4. Press the EXIT button or Back Select to exit.
Changing the Language Standard
Page 22
OLS-PGB/P Series
22 of 33
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Language, then press the ENTER button.
3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
Language
It is variable depending on the model. When you start using the television for the first time, you must select the
language which will be used for displaying menus and indications.
4. Press the EXIT button or Back Select to exit.
Changing the Misc. Standard
Page 23
OLS-PGB/P Series
23 of 33
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Misc., then press the ENTER button.
3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
Adjusts the
OSD Time.
3-1. Select the required mode by pressing the or button, then press the ENTER button.
Changing the input Source D-SUB and DVI.
Page 24
OLS-PGB/P Series
24 of 33
Reset.
3-2. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
Reset: You can return to the factory defaults settings
4. Press the EXIT button or Back Select to exit.
Changing the Audio Standard
Page 25
OLS-PGB/P Series
25 of 33
1. Press the MENU button to display the menu.
2. Press the ▲ or ▼ button to select Audio., then press the ENTER button.
3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
Adjusts the
Volume.
3-1. Press the or button until you reach the optimal setting.
Page 26
OLS-PGB/P Series
26 of 33
Adjusts the
Mute.
3-2. Press the or button until you reach the optimal setting.
4. Press the EXIT button or Back Select to exit.
Changing the Exit.
1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button.
OSD Menu Exit.
Page 27
OLS-PGB/P Series
27 of 33
Specifications
OLS-3201PGB
Items Specifications
32 inch
Display Size 32 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Pixel Size 0.51075(H) x 0. 51075 (V) mm
Resolution 1366 x 768 (WXGA)
Colors 8 bit, 16.7M Colors
Brightness 600cd/㎡ (Typ)
Contrast Ratio 2000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 760.0(H Typ) x 450.0(V Typ)
POWER
AC Input AC 100~240V~, 50/60Hz, 1A
Power Consumption 210W
OLS-4001PGB
Items Specifications
40 inch
Display Size 40 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Pixel Size 0.461225(H) x 0. 461225 (V) mm
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 450cd/㎡ (Typ)
Contrast Ratio 4000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 952.0(H Typ) x 551.0(V Typ)
POWER
AC Input AC 100~240V~, 50/60Hz, 1A
Power Consumption 260W
Page 28
OLS-PGB/P Series
28 of 33
OLS-4001PGP
Items Specifications
40 inch
Display Size 40 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Pixel Size 0.46125(H) x 0. 46125 (V) mm
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 700cd/㎡ (Typ)
Contrast Ratio 3000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 911.7(H Typ) x 524.0(V Typ)
POWER
AC Input AC 100~240V~, 50/60Hz, 1A
Power Consumption 260W
OLS-4601PGB
Items Specifications
46 inch
Display Size 46 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Pixel Size 0.53025(H) x 0. 53025 (V) mm
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 450cd/㎡ (Typ)
Contrast Ratio 4000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 1083.0(H Typ) x 627.0(V Typ)
POWER
AC Input AC 100~240V~, 50/60Hz, 1.5A
Power Consumption 320W
Page 29
OLS-PGB/P Series
29 of 33
OLS-4601PGP
Items Specifications
46 inch
Display Size 46 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Pixel Size 0.53025(H) x 0. 53025 (V) mm
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 700cd/㎡ (Typ)
Contrast Ratio 3000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 1018.08(H Typ) x 572.67V Typ)
POWER
AC Input AC 100~240V~, 50/60Hz, 1.5A
Power Consumption 320W
OLS-5501PGB
Items Specifications
55 inch
Display Size 55 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 450cd/㎡ (Typ)
Contrast Ratio 5000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 1209.2 (H) x 680.4 (V)
POWER
AC Input AC 100~240V~, 50/60Hz, 1.5A
Power Consumption 380W
Page 30
OLS-PGB/P Series
30 of 33
OLS-5501PGP
Items Specifications
55 inch
Display Size 55 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 700cd/㎡ (Typ)
Contrast Ratio 3000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 1209.2 (H) x 680.4 (V)
POWER
AC Input AC 100~240V~, 50/60Hz, 1.5A
Power Consumption 400W
OLS-7001PGB
Items Specifications
70 inch
Display Size 70 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Pixel Size 0.807(H) x 0. 807 (V) mm
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio 2000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 952.0(H Typ) x 551.0(V Typ)
POWER
AC Input AC 100~240V~, 50/60Hz, 9.2A
Power Consumption 920W
Page 31
OLS-PGB/P Series
31 of 33
OLS-7001PGP
Items Specifications
70 inch
Display Size 70 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Pixel Size 0.807(H) x 0. 807 (V) mm
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 600cd/㎡ (Typ)
Contrast Ratio 2000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
Panel Size 952.0(H Typ) x 551.0(V Typ)
POWER
AC Input AC 100~240V~, 50/60Hz, 9.2A
Power Consumption 950W
OLS-8201PGB
Items Specifications
82 inch
Display Size 82 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness
450cd/㎡ (Typ)
Contrast Ratio 2000:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
POWER
AC Input AC 100~240V~, 50/60Hz
Power Consumption 950W
Page 32
OLS-PGB/P Series
32 of 33
OLS-8201PGP
Items Specifications
82 inch
Display Size 82 Inch (16:9) : LCD / S-PVA TFT
Response Time 8 ms(Typ G to G)
Resolution 1920 x 1080 (WUXGA)
Colors 8 bit, 16.7M Colors
Brightness 600 cd/㎡ (Typ)
Contrast Ratio 1200:1
View Angle Hor. 178 Degree(Typ), Ver. 178 Degree(Typ)
Surface Treatment Hard coating(3H), Haze 44%
POWER
AC Input AC 100~240V~, 50/60Hz
Power Consumption 980W
Items Specifications
PC
CPU AMD 3.0G
Main Board MINI ITX
Memory 2G
HDD 160G
Graphic NVIDIA 8200
OS EMBEDDED STANDARD
Page 33
OLS-PGB/P Series
33 of 33
EWF (Enhanced Write Filter)
Most of the characteristics of the XPE feature is to use the EWF.
This is to protect the disk, as well as to protect the system files you can enjoy a twofer.
The principle is simple.
Jungle of the disk to the operating system and Overlay (RAM or Disk) and having the disk write
When done, Overlay be made in writing is to create.
Look at the picture below, the faster you will understand.
EWF is protecting the painting to be done at the point of writing indicates that when you know how it all
works.
Overlay does not write directly on the partition to copy the file that is in the region.
EWF is protected from the outside that you or your system settings, if you copy a file to actually Disk
Copy or in the area, which is set to Overlay, which is not. If you use the RAM Overlay
When you reboot, all the copies has been set, or will be lost.
C drive by the EWF function is to protect the System file.
Add a program or file on the C drive, reboot and nevertheless addition will be deleted.
Remember to add the program or file, please work on the D drive.
Operating Temperature : 0 ~ 32.
Quality assurance : The warranty period is one year
This product can be changed to improve performance without notification.
The up contents not to notify can be changed.
HEAD OFFICE FACTORY : 257-6 GONGDAN-DONG, GUMI, GYEONGBUK, KOREA
TEL 82-54-460-5700 FAX : 82-54-461-3284
App
lication
File system
EWF
Overlay
(RAM or Disk)
Partition
Loading...