by Orion
NOTE: This instruction booklet
contains safety information.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
ASSEMBLY MANUAL
www.orionfighttech.com
INTERACTIVE TRAINING SYSTEM
TABLE OF CONTENTS
Important Safety………………………..……………2
Maintenance……………………….……….………….3
Parts………………………………………………………...4
Assembly……………………………………………….5-6
Instructions for Use……………………….………7-8
Warranty………………………..………………………13
Moving/Storage………………………………………14
Maintenance………………………………………….16
FIGHT TECH BY ORION 2
OBEY FOLLOWING WARNINGS:
• KEEP PEOPLE AWAY WHILE ASSEMBLING
• UNIT IS NOT TO BE LEFT OUTDOORS
• SOME COMPONENTS MAY BE AWKWARD OR HEAVY TO MOVE.
USE A SECOND PERSON TO HELP
*CLEAN FLOOR BEFORE ADHERING FASTENERS TO HARD FLOOR.
*ADHERE TO CLEAN, DRY, LEVEL FLOOR (IF STICK TABS ARE DAMAGED, REPLACE
IMMEDIATELY)
• TWIST SHAFT THROUGH DESIGNATED HOLE.
• DO NOT USE WITH BYSTANDERS IN CLOSE PROXIMITY.
• ASSEMBLE IN SEQUENTIAL ORDER
• READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING
UNIT.
• CALL OR EMAIL WITH QUESTIONS:
techsupport@ or call 1-800-xxx-xxxx
• PUMP NEEDLE TO FILL AIR BAG MUST BE MOISTENED BEFORE
INSERTING IN SPEED BAG.
Maintenance
FIGHT TECH BY ORION 3
• DO NOT LEAVE OUTDOORS. WEATHER WILL
DAMAGE.
• COVERS ON TARGETS CAN BE REMOVED AND
WASHED-GENTLE/COLD
• KEEP BEARINGS AND WASHER SUPPOSRTS WELL-
OILED TO PREVENT DAMAGE. RUSTING WILL
REDUCE THE DISTANCE THAT THE ARM TRAVELS.
AN OIL IS PROVIDED FOR OILING IN DISPENSER.
• ALWAYS CHECK FOR LOOSE CONNECTIONS OR
SCREWS BEFORE USING.
• BASES CAN BE CLEANED WITH SOAP AND WATER.
• SPEED BAG AIR SHOULD MAINTAIN AIR PRESSURE
AT APPROXIMATELY 90 PERCENT OF THE BAGS
CAPACITY (ONCE FILLED, BAG SHOULD BE SOFT
ENOUGH TO S INTO).
FIGHT TECH BY ORION 4
Part Identification
ITEM QTY
DESCRIPTION DIMENSION WEIGHT
1 1
SHAFT
96” X 1”
7 LBS.
2 1
FOAM SPACER
25
-1/2”X2-1/8”
5 OZ.
3A N/A
ADHERED
BASE
18” X 18” X 4”
15 LBS.
3B N/A
STAND
-ON BASE
54” X 24” X 3
-7/8”
41.5 LBS.
4 1
HEAD TARGET
15” X 12” X 5”
26 OZ.
5 4
BEARINGS
6 8
BEARING WASHER
7 2
COLLAR
8 2
BUSHING
SPACER
9 2
ROTATING
ARM
26
-1/4”X3-1/2”X3-1/2”
15.5 OZ.
10 2
UPPER CUT TARGET
12
-1/2”X3-1/2”X3-1/2”
14.5 OZ.
1 2 3 4
5
6
7
9
10
8
FIGHT TECH BY ORION 5
Hardware Identification
ITEM
QTY/SET
DESCRIPTION NOTES
10 1
1/8” ALLEN WRENCH
11 1
3/16” ALLEN WRENCH
12 6
¼
-20 SET SCREW
13 4
¼
-28 SET SCREW
14 14
FLOOR FASTENERS
SMALL BASE ONLY
7 TOPS
7 BOTTOMS
15 1
AIR PUMP
16 1
AIR NEEDLE
FIGHT TECH BY ORION 6
• Please be sure to inspect unit for all listed materials before proceeding with assembly.
• Unit must be properly secured to the floor.
• Use equipment at your own risk, and always consult a physician before starting any new
exercise.
• KEEP OTHERS AWAY DURING ASSEMBLY UNLESS HELP IS NEEDED FOR LIFTING COMPONENTS.
Assembly of Unit
Place the strips of the floor
fastener onto the base. Spread
out as shown in picture above.
Peel back the adhesive strip from
the fastener and discard. Then
place the unit in the desired
location on the floor. FLOOR
MUST BE CLEAN, DRY, AND LEVEL.
Step on the unit to seat the
fastener into place. Tool will be
required for removal after
fastener is locked in, such as a flat
head screwdriver
Gently twist shaft into the
center hole. Do NOT force straight
down. Secure the base using (3)
set screws and tighten down using
the 1/8 allen wrench provided. Do
NOT over tighten.
Place the foam spacer over the
shaft as shown.
Place the middle target (item 5)
where desired (recommended to
set around waist height) and
tighten (2) set screws using the
provided 1/8” allen wrench.
1
2
3
4
5 6
FIGHT TECH BY ORION 7
• Please be sure to inspect unit for all listed materials before proceeding with assembly
instructions.
• Unit must be properly secured to the floor.
• Use equipment at your own risk, and always consult a physician before starting any new
exercise.
Assembly of Unit
Place (1) collar at the approximate
height desired for the rotating
target (user’s shoulder height is
recommended). Secure in place
using (2) set screws with the 3/16”
allen wrench.
Place (1) washer followed by (1)
thrust bearing, and then (1) washer
over the shaft.
The rotating arm will be delivered
assembled. Remove half of the
assembly. Place the (long) rotating
arm over the assembly remaining
on the shaft. Tighten bottom
collar using the 3/16 allen wrench
provided. Turn down tight with
the arm in position to your
shoulder.
7
8 9
10
11
Use included air pump in order to
Moisten the needle and fill the
head target as shown above. Be
sure not to overfill-only fill to 90%
full.
Lower the top assembly over the
top of the arm down the shaft.
Lower the top collar down the
shaft trapping all of the parts
together. Apply a small amount of
pressure to the collar and tighten
top collar.
Place the head target (item 10)
onto the unit in the orientation
shown above. Secure in place
using (2) set screws with the
3/16” allen wrench.
12
Instructions for Use
Attaching The Base To A Mount
Fight Tech comes with two optional mounts for the base of the machine. The first mount allows the user to
attach the base to the floor and a second mount that doesn't require any floor attachments.
For the floor mounting base, find a hard surfaced location that is best suited for the movement and activity
required to use Fight Tech efficiently and make sure the surface area is clean of dirt and dry
for proper adhesion. Remove all the protective tape covers from underneath the base. Place the unit on the
floor with the sticky side exposed to the floor's surface. Once placed on the hard surface,
press the base to the floor using one's weight to the base for the development of a strong stick.
NOTE: The adhesive tabs are only one time use. Once the tabs are removed from the floor they will lose their
adhesive properties. They are meant to remain stuck to the floor while the base
and the machine at large can be disconnected from the floor tabs. Extra tabs are provided.
In order to remove the base, a strong elongated object will be needed to pry the base from the floor.
To reinstall the base to the floor, align the tabs on the bottom of the base to the tabs on the
floor. Once the tabs are aligned, step on the base until a snap is heard indicating that the base is now attached
to the floor tabs. The shaft is now ready to be installed once the base is firmly
attached to the floor.
Instructions for Use
Adding The Targets
1) The shaft is mounted onto the pre-drilled hole found in the base. When inserting the shaft twist the shaft into
place. Do not force shaft down into base. Once the shaft makes contact with the stopper, tighten the three screws
found on the side of pre-drilled hole to lock in place the shaft.
2) It is necessary to mount the two uppercut targets before mounting the arm targets if use of the uppercut
targets is desired.
3) The arm target should be positioned approximately to shoulder height for most effective use. To adjust and
fasten arm position, loosen collars attached to shaft with the Allen wrench provided.
Rest the arm upon your shoulder to determine the proper height. Difficulty of striking the arm target can be varied
by adjusting the position of the arm target - below the shoulder for a slightly more
difficult and refined work-out, or above the shoulder for an easier and more accessible target.
4) Secure the collar with the Allen wrench once the appropriate height has been determined. Try to keep the arm
as straight as possible when tightening the collars.
5) After the arm position is set and bottom collar is secure, slide down the rest of the arm assembly down the
shaft which consists of four bearing washers and two thrust bearings.
6) Make sure the arm is secure without being fastened too tightly. The arm should be able to spin freely and up to
approximately four revolutions with a moderate push. If it is either too loose or tight,
further adjustments need to be made. An indication of the bearing be fastened too tightly is if the movement of
the arm is restricted and rotates without ease. Likewise, a clear indication
that the arm is fastened too loosely is if the bearings rattle upon revolution of the arm.
7) The head target is fastened to parallel the height of the user's head. The position of the head can be adjusted by
loosening and then tightening the screws in the back of the head target.
The target should be tightened until it does not move on the shaft.
8) The position of the uppercut targets can be adjusted similarly to the head target -- by loosening and tightening
the screws found in the back of the target. The position of the uppercut
targets are best put at the mid section of the user but may be adjusted depending on the user's skill level and
comfort.
9) The bag for the head target should be pumped until the bag feels almost full. The bag should have enough air so
it may be squeezed and be able to surround the fingertips.
The needle needs to be wet prior to insertion and pumping.
Although the arm target is made primarily from foam, it is recommended to use Fight Tech with protective
sparring gloves, as persistent contact with the surface can possibly irritate the skin
on some individuals.
Fight Tech can be equipped with the recoil apparatus to generate quicker return strikes by the arm. This is
recommended for advanced users only, as a greater level of agility and coordination
is required. The recoil apparatus will soon be available in addition to a rotating kicking target.
ADDITIONAL SAFETY INFORMATION
FIGHT TECH BY ORION 10
Warranty Information
Prior to use of FightTech or any exercising and conditioning program that utilizes
FightTech be sure to consult your physician or athletic trainer. Read all instructions
as they are necessary to avoid injury and damage to the device. Overuse of
FightTech can lead to undue strain on muscles and breathing as is common with all
strenuous cardiovascular training. It is necessary for the beginner to start slow and
progress in speed until a sufficient technique is developed. As FightTech is a
complete body work out, it requires the use of muscle groups not commonly
exercised with most gym equipment which can often produce soreness typical
after strenuous exercise by under used muscles groups. As the body adapts to the
rigors of FightTech, the delayed workout soreness will dissipate with time as the
body develops muscle from use.
The manufacturer provides a warranty of FightTech in full replacement for any
defective parts for up to one year after purchase.
In order to obtain the warranty the unit must be registered online. Online
registration will also allow the user to easily purchase additions and upgraded
parts. The customer's personal information will not be passed on to or sold to any
third parties under any circumstance.
The warranty only covers damages caused by intended use of FightTech, as the
unit should not sustain damage during recommended usage.
Warranty for the shaft is limited to irregularities at points for entry and removal of
parts or if the shaft is bent upon initial purchase. Due to metal on metal contact
and plastic revolving around the shaft, a dull discoloration on the shaft is possible
and cannot be avoided with continuous use. This will not inhibit the effectiveness
or integrity of the shaft. It is necessary to avoid using acutely aggressive strikes at
the machine to prevent damage over accumulated power strikes. Though
FightTech is designed to take punches of high magnitude, it does not have the
durability of a punching bag under full strength strikes.
We reserve the right to change or modify Fight Tech training units without notice.
Loading...