Orion 19RTC, 17RTC User Manual

Installation and User's Guide

PREMIUM NORMAL ASPECT RATIO SERIES

(17~20 inches)

http://www.orionimages.com

All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein

Installation and User's Guide

1. SAFETY INSTRUCTION

Follow this safety instruction to use the monitor properly and prevent the damages.

This safety instruction has “Warning” & “Caution” as below

Warning -

Caution -

If the user does not follow this instruction, it may cause the serious damage to the user.

If the user does not follow this instruction, it may cause the slight damage to the user or cause some damages to the monitor.

Keep this user’s guide book for later use.

Warning

Never remove the back over and touch the inside of the monitor. If you need a service, please contact the service center.

Never push objects of any kind into this product as they may result in a risk of fire or electric shock.

Keep away the monitor from the direct sunlight and a heating appliance.

Connect the power code to the wall outlet tightly. If the power code or plug are defective and the wall outlet is not tight, please do not use them.

Warning

Installation and User's Guide

Do not install this monitor on the outside and near water. If may cause damage to the product, electric shock and fire.

When lightning and thundering, unplug the monitor from the wall outlet and never touch it.

When smoking and noising from the monitor, unplug the product from the wall outlet and contact a service center.

For cleaning do not use liquid cleaners. Never touch the power plug with wet-hands.

Unplug this product from the wall outlet, when It does not operate for a long time.

IIN

How to fix

RNN

Do not open this product as it contains high voltage inside. It may create an electric shock. It the user disassembles and remove the back cover, it does not make sure to make up for the damages and do a service and exchange the monitor.

Cautions

Installation and User's Guide

Install this monitor some distance From the wall and do not install unless Proper ventilation is provided.

The openings must not be blocked by curtain, rug or other similar surface.

Before carrying the monitor, tum it off and Unplug the signal cables and the power code From the wall outlet.

Place this product on a stable place. If not, it may fall, causing serious Damages to the monitor and people.

When carrying this monitor, be careful not to damage the panel and drop it It may cause some trouble.

Take the power plug out from the wall outlet. Do not pull the cable. It may snap the innerwires and cause overheating and fire.

Cautions

Installation and User's Guide

Install this monitor about 50cm far from the eyes and an angle of 0~15 degrees below eyes. Too close installation may cause having weak sight.

For cleaning, unplug the monitor from the Wall outlet. Do net use the liquid cloth. Use the soft cloth.

Do not press the LCD panel with hands or the sharpened material hardly.

Do not use the chemical liquid for cleaning. It may cause fading and breakage.

Installation and User's Guide

2. FCC RF INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfere partic

ular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio, TV technician for help. Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.

nce will not occur in a

DOC COMPLIANCE NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference re

ulation of Canadian Department of communications.

Installation and User's Guide

TABLE OF CONTENTS

1. SAFETY INSTRUCTION 1-1 Warning

1-2 Caution

2. FCC STATEMENT

3. INSTALLATION 3-1 Parts 3-2 How to Install

4. OSD MENU SETTING 5-1 Mode Setting 5-2 Menu Setting (VIDEO, S-VIDEO, COMPONENT Mode) 5-3 Menu Setting (VGA Mode)

5-4 Menu Setting (DVI, HDMI Mode)

5. FEATURES

6. LIMITED WARRANTY

7. TROUBLESHOOTING

3. INSTALLATION

3-1 Parts

Installation and User's Guide

LCD Monitor

* Adapter is attached to the back of product

VGA Cable Trigger Cable Power Cable

Battery User Manual

Remote Controller

Adapter

3-2 How to Install

KEY BUTTON

Installation and User's Guide

SHORT KEY FUNCTION

OSD Key Function

Activates and exit the OSD Select input source, and select the OSD menu Move the OSD menu and auto adjustment of RGB source Decrease the level of volume and move the previous menu Increase the level of volume and select rhe OSD menu

Turns the power ON or OFF.There will be a few seconds delay before the display appears.The power LED (next to the power switch) lights with green when the power is turned ON. The power is turned o ff by pressing the power switch again and the power LED goes red.

CONNECTION

1 2 3 4 5 6 7 8 9

Installation and User's Guide

DC12V

DC adapter input VIDEO-2 signal input / looping out

AUDIO (PC)

Stereo audio input for VGA VIDEO-1 signal input / looping out

COMPONENT

COMPONENT (Y/Pb/Pr) signal & stereo audio input TRIGGER signal input

AUDIO (VIDEO-2)

Stereo audio input for VIDEO-2 HDMI signal 1 / 2 input

AUDIO (VIDEO-1 / S-VIDEO)

Stereo audio input for VIDEO-1 or S-VIDEO DVI signal input

S-VIDEO IN / OUT

S-VIDEO signal input / looping out VGA (PC RGB) signal input

VIDEO-2 IN / OUT

VIDEO-1 IN / OUT

TRIGGER

HDMI

DVI

VGA

Installation and User's Guide

REMOTE CONTROLLER

MODE SELECT MENU

VIDEO1

Select VIDEO1 mode

POWER MUTE

VIDEO1 VIDEO2 S-VIDEO

VGA AUTO COLOR TEMP

DVI HDMI1 COMPONENT

HDMI2 S.SET

SCAN MODE PIP

VOL- VOL+

MENU/EXIT

P.INPUT P.LOCATION

P.SWAP STILL

KEY LOCK

P.SIZE

S-VIDEO

Select S-VIDEO mode

DVI

Select DVI mode

COMPONENT

Select COMPONENT mode

OSD CONTROL MENU

POWER

Turn ON / OFF the monitor

AUTO

Auto adjust position of the screen (in VGA mode)

SCAN MODE

Select the scan mode of the screen

MENU / EXIT

Activate and exit the OSD menu

STILL

Freeze the current image

VIDEO2

Select VIDEO2 mode

VGA (RGB)

Select VGA mode

HDMI1

Select HDMI1 mode

HDMI2

Select HDMI2 mode

MUTE

Turn ON / OFF the sound

COLOR TEMPERATURE

Select color temperature of the screen

VOL- / VOL+

Increase / Decrease the volume level

KEY LOCK

Locking the button (Prevent operation)

PIP CONTROL MENU

S. SET

Select between main and PIP audio input

P. INPUT

Select an input source for PIP mode

P. SIZE

Select a size for PIP mode

PIP

Activates PIP/PBP mode

P. LOCATION

Select a location for PIP mode

P. SWAP

Swap between main and PIP input

+ 25 hidden pages