HP100
Corded Hotel Phone
Location of Controls
1
2
3
4
5
6
7
Reception OutsideLine RoomService Restaurant HouseKeeping
Concierge WakeUp Call Airport Taxi Emergency
9
10
11
100 300 600
Program/Store
Programer
21
Store
ABC DEF
JKL
GHI
5
4
TUV
PQRS
7
8
Redial
321
MNO
Recall
6
WXYZ
Mute
9
Volume
#0
12
13
14
15
16
17
18
19
20
Keep this user guide for future reference
Installation
Connection
1. Connect one end of the curly cord to the handset, and the
other end to the socket marked HANDSET on the left-hand
side of the base.
2. Connect the telephone line cord to the LINE IN socket on the
telephone, and to a telephone network wall socket.
3. Lift the handset and listen for the dial tone. Your telephone is
now operational.
4. Ensure the correct Recall time has been set for your
system/PBX or phone.
For Desk Use
Fit the desk support onto the base of the phone.
Messages
8
1. Program/Store switch
2. Programmer switch
3. Hook switch
4. Handset holder
5. Speaker
6. Keypad
7. Handset cord jack
8. Message waiting and Visual
Ringer indicators
9. Telephone line jack
10. Flash/Recall time 100/300/600
switch
11. Message Waiting switch
12. Line 1/2 switch
13. Store button
14. Data port
15. One touch memories
16. Redial button
17. Ringer volume Hi/Lo switch
18. Recall button
19. Mute button
20. Handset volume control button
21. Messages button
Wall mounting your phone:
For wall mounting installation, do not insert the desk support on the
base.
1. Revolve the handset catch 180° to the wall mounting position
using a small coin.
2. Connect the telephone line cord to the LINE IN socket on the
telephone, and to a telephone wall socket.
3. Run the telephone cable inside the groove and ensure it is
tight.
4. Drill two holes vertically, one above the other, 83mm apart, and
leave the screws protruding from the wall by 5mm.
5. Align the base’s keyhole slots with the screws and slide the
phone downward to secure it.
6. Lift the handset. Listen for the dial tone to ensure the telephone
is working.
Using your phone
Making a call
1. Lift the handset and dial tone will be heard.
2. Dial the required telephone number.
3. On completion of the call, hang up the handset
Answering a incoming call
1. When an incoming call is received, the phone will ring,
2. Pick up the handset to answer the call.
3. On completion of the call, hang up the handset.
21
Redial
1. Lift the handset.
2. Press Redial to redial the last number dialled.
Volume cont rol
The handset earpiece volume may be increased or decreased during
a call. Press the Volume button to increase or decrease the volume.
Recall (Australia ONLY)
You can use the Recall button on your telephone when using your
network operator’s services such as call waiting etc. A subscription
may apply for these services, contact your network operator for more
information. If this is not working correctly check the country option in
the phone menu and select Australia or New Zealand options. For
Australia it should be set to 100ms and for New Zealand 600ms.
Mute button
The handset volume can be muted during a call by pressing MUTE
button. Release the MUTE button to reactivate the microphone.
Ringer volume control
The ringer volume can be adjusted using the Ring Volume switch
located on the right-hand side of the telephone
Memory
This telephone has 10 One-Touch memories.
Storing One-Touch Memories
1. Ensure the Program/Store switch is set to Store.
2. Lift the handset, the dial tone will be heard (ignore any tone).
Press Store button.
3. Enter the telephone number to be stored (up to 32 digits).
Press Store.
4. Select a memory position by pressing the corresponding
memory button.
5. Replace the handset.
If you need to insert a pause in the telephone number press
Redial
If you need to change a number, store the new number in the same
location as the old one.
Dialling using One-Touch Memories
1. Lift the handset, the dial tone will be heard.
2. Press the required One-Touch memory button.
Messages button
You can also store a telephone number into this button like the one
touch memory buttons:
1. Ensure the Program/Store switch is set to Store.
2. Pick up the handset, the dial tone will be heard. (ignore the
dial tone) press Store button.
3. Enter the telephone number to be stored (up to 32 digits).
Press Store.
4. Press the Messages button, now n umber have been stored.
5. Replace the handset.
Dial the pre-programmed number
1. Lift the handset. You will hear the dial tone.
2. Press the MESSAGES button. A pre programmed number will
be dialed automatically.
Line Switch
There is a line switch on the top of the unit which allows you to select
the desired telephone line 1 or line 2 depends on your selection.
You may configure the phone using the switch located under the inlay
on the base of the phone marked 1 and 2 so that the telephone (1)
and the outer port (2) are connected in parallel.
Connection of additional equipment
Additional equipment such as modems can be
connected to this telephone via the DATA PORT socket
on the right side of the base. Two meth ods of operation
can be selected by using the switch located
on the top of the base (Please refer to "Location of
controls" point 12):
1. Allows for single line parallel operation. For example,
a computer modem can be operated through the
telephone but only one device can be operated at a
time, either the modem or the telephone.
2. Allows for two line operation where a computer
modem can be connected via the telephone and both
devices can be used at the same time. The network
wall socket must have two lines connected.
Hearing aid compatible
This telephone is hearing aid compatible. Select the T mode on your
hearing aid to enable this feature.
Programmer lock
The Program/Store switch (located under the underlay) allows
access to the One-Touch memory programming.
Store Manual programming allowed.
Program Programmer downloads allowed.
PBX Message W aiti ng
Most PBX systems use a function called Message Waiting. The
telephone will indicate when a call was received by flashing the
Massage Waiting lights next to the Messages button.
The MW switch is located on the top side of the telephone.
The MW function operates differently depending on the PBX in
question.
Please contact the PBX administrator for more information.
The following four alternatives are available: LED+, LED-, ringer
indicator (
When the telephone is used in systems without a telephone
exchange (
) and high DC voltage (HV).
) should be selected.
Programmer
A dedicated programmer (optional) can be connected to the
Programmer socket located on the top side of the telephone, this
allows easy programming of the 10 One- Touch memories and the
number in Messages key.
The Program/Store switch (located on the top side of the telephone)
must be set to Program.
General Information
Warnings
• The telephone is designed for indoor use only. Do not install
the telephone in areas where there is the risk of an explosion,
excessive exposure to smoke, dust, vibrations, chemicals,
moisture and heat.
• Do not install in damp locations such as a bathroom or laundry,
do not expose the unit to direct sunlight.
• Do not use your telephone during an electrical thunderstorm as
it is possible to get an electric shock. Refer to information
contained in Telstra White pages directory.
• The earpiece of the handset may attract small metal objects
such as staples and pins. Care should be taken when placing
the handset near these items.
• This phone is designed for connection to a PSTN telephone
line or analogue extension port of a PBX system. If you
connect this device to a digital extension of PBX, damage may
result to the PBX.
Trouble Shooting
If you feel this product is not working correctly please consult the user
guide and ensure that you are using the product in accordance with
the instructions.
Remove all extra telephone equipment and connect only this
telephone directly to the telephone socket.
If the fault is still present, connect another telephone (if available) to
the telephone socket. The results will show you whether the fault lies
with this unit or with the telephone line. If the product is not working
correctly the fault is on the telephone line. Please contact your
network operator for assistance. In the unlikely event of a fault
developing please return the product to the retailer where you
purchased it.
Cleaning and Care
The surface of the case can be cleaned with a dry, soft, lint-free cloth.
Never use cleaning agents, particularly aggressive solvents.
Notes for operation in
New Zealand
The grant of a Telepermit for any item of terminal
equipment indicates only that Telecom has accepted
that the item complies with the minimum conditions for
connection to its network. It indicates no endorsement of
the product by Telecom, nor does it provide any sort of
warranty. Above all, it provides no ass urance
that any item will work correctly in all respects with
another item of Telepermitted equipment of a different
make or model, nor does it imply that any product is
compatible with all of Telecom’s network services. This
device may be subject to ringing or bell tinkle when
certain other devices are connected to the same line. If
this occurs, the problem should not be referred to the
Telecom Faults service. This equipment shall not be set
to make automatic calls to the Telecom “111”
Emergency Service. This equipment may not provide for
the effective hand-over of a call to another device
connected to the same line. Telepermitted equipment
only may be connected to the auxiliar y telephone port.
The auxiliary telephone port is not specifically designed
for 3-wire connected equipment that may not respond to
incoming ringing when attached to this port.
REN (RN for New Zealand)
The REN (Ringer Equivalence Number) or (RN) is of
significance only if you wish to connect more than 1
telephone to your telephone line. A standard telephone
line has a maximum REN capacity of 3 (RN of 5). It is
possible to connect 3 (5) devices with a REN of 1 (RN
of 1) with no degradation to the product’s performance.
Exceeding this limit may cause the volume of the ringer
in any phone to decrease or not ring at all.
Australia
Oricom International Pty Ltd
Locked Bag 658, South Windsor, NSW 2756
Customer Support
Email: support@oricom.com.au
Web: www.oricom.com.au
Phone: (02) 4574 8888 Fax: (02) 4574 8898
New Zealand
Atlas Gentech (NZ) Limited
Private Bag 14927
Panmure, Auckland
Customer Support
Email: support@at lasgentech.co.nz
Web: www.atlasgentech.co.nz
Phone: 0900 50 025 (Toll Call) Fax: (09) 574 2722
Loading...