Oregon TR118 User Manual

2 CHANNEL

JUMBO DISPLAY CLOCK TIMER

INSTRUCTION MANUAL

MODEL:TR118

DUAL-TIMER

HMSC

BATTERY
COVER

MODEL NO. TR118

ENGLISH

TIMER FEATURES:

1. 2 Channel LCD Count-down and Count up Timer together with Clock.

2. 6 digits display showing HOUR, MINUTE, and SECOND for both Timers
and Clock.

3. Automatic count-up after Timer counts down to zero.

4. Count-down timer: Maximum setting is 99 hours, 59 minutes and 59 seconds
at 1 second resolution.

Count-up timer: Maximum count-up range is 99 hours, 59 minutes and 59
seconds at 1 second resolution.

5. Buzzer alarm sounds for 1 minute when timer counts to zero.

6. Timer memory recall for each count-down timer.

7. Individual buttons for HOUR, MINUTE and SECOND setting.

NORMAL TIME SETTING

1. Press the Clock button down for approximately 3 seconds. The digits and
colon will flash on the display.

2. Press the Hour button to advance to the correct hour. Hold button down for
approximately 2 seconds for fast setting.

3. A “P” will appear on the display below the colon for PM. There is no symbol
for AM indication.

4. Press MIN button to advance to the correct minute. Hold the button down
for approximately 2 seconds for fast setting.

5. Press the SEC button to reset second digit to zero when the second digits
are within the 00-29 second range; pressing SEC button in 30-59 second
range advances minute setting by 1 minute and resets second digits to zero.

6. Press the Clock button to start clock. The colon will flash in clock mode.

7. The Clock operates independently of the timing channels. Whenever the
clock button is pressed, the time of day will appear on the display. If timers
are operating, T1 or T2 respectively will flash.

12/24 HOUR FORMAT SELECTION

1. To activa te 24 hour format, in Clock Mode hold STA R T/STOP button down
for approximately 3 seconds, beep tone will indicate format change.

2. To change back to 12 hour format, repeat step 1 above.

CLEAR

T1

T2

START

STOP

MEMORY

CLOCK

MAGNET

PLASTIC
CLIP

4. Both timer channels can be used at the same time. When using both timer

channels, simply press the T1 or T2 button to note count down time
remaining. Non-flashing (T1 or T2) indicates the count down time of the
channel being displayed.

TIMER BUZZER ALARM

1. When timer counts to 00H, 00M and 00S, timer buzzer alarm will sound
and timer will begin to count up in seconds with respective non-flashing
timer channel indicator appearing in display.

2. Timer buzzer will be stopped by pressing any button.

3. Buzzer will automatically turn off in 60 seconds. Count-up timer continues
to operate until stopped.

4. Count-up timer in alarm mode can be stopped by pressing any button.

5. Press Clear button to reset display to zero.

6. If both channels are counting down, when time expires in both channels
within a minute of each other and the alarm has not been turned off, the
alarm for the just expired timer will sound with the other timer channel
flashing in the display. Turn off by pressing the START/STOP button.

7. The other channel alarm will sound at the completion of cycle, and the
indicator will count up.

8. Press START/STOP button to turn off.

TIMER MEMORY RECALL

1. After timer buzzer alarm stops, press START/STOP button once to recall
preset timer time.

2. Press START/STOP button again to start timer.

COUNT-UP/STOPWATCH TIMER

1. Press desired timer channel button.

2. Press CLEAR button to clear display.

3. Press START/STOP button and time will begin to count-up in 1 second
resolution.

4. Press START/STOP to stop count-up timer.

5. If you wish to restart timing process, press START/STOP button again.

6. To turn timer off, press START/STOP button and then Clear button.

7. If count up/stopwatch timer is not turned off when it reaches 99 hours, 59
minutes, 59 seconds, it will start counting over again at 1 second resolution
from 00H, 00M, 00S.

BATTERY REPLACEMENT

To replace exhausted battery, slide push the battery cover on backside in direction
of arrow. Set cov er aside and remo v e battery. Insert a now 1.5V ‘ AAA’ battery as
indicated by the polarity symbols (+&-) marked and close battery cover.

Sometimes the timer may not activate after installing a new battery. If this happens,
simply remove battery from the battery compartment and reinstall again. The
Clock will resume normal operation.

CLIP ATTACHMENT

The timer can clip on thin board, belt or shirt pocket using the plastic clip on the
backside of timer.

MAGNETIC ATTACHMENT

The timer can attach to iron or steel surface, using the magnet attached to the
clip on the backside of the timer.

TABLE TOP USE

Use the clip and metal stand bar together to stand the clock/timer at an angle on
any flat surface.

SPECIFICATIONS

Power: use 1 pc UM-4 or “AAA ” 1.5V ba ttery
Weight: 0.18 lbs (without battery)
Dimension: 2.75" x 0.75" x 2.5" (LxWxT)

CAUTION

- The content of this manual is subject to change without further notice.

- Due to printing limitation, the displays shown in this manual may differ
from the actual display.

- The contents of this manual may not be reproduced without the permis
sion of the manufacturer.

COUNT-DOWN TIMER SETTING (SEE FIG.1)

1. Press either T1 or T2 button for desired timing channel. The selected channel,

T1 or T2, will appear on the display. The colon does not flash in the timer
mode.

2. Press CLEAR to reset timer to zero.

3. Press individual HOUR, MIN & SEC buttons to program desired time.

The numbers can be fast forwarded by holding the individual buttons down
for 2 seconds.

4. If error is made in programming, hold individual HOUR MIN & SEC

button down first, then press the clear button to zero the digit. Then reprogram
as explained above.

5. Follow the same procedure above for programming the other timer channel.

TIMER START/STOP

1. After time setting is ready, press START/STOP button once to activate

timer. Steady T1 or T2 indicator on screen shows activ e channel on display.

2. When timer is counting, press START/STOP button once and displayed

timer channel will pause.

3. Press START/STOP button once and timer will resume counting.

CUSTOMER ASSIST ANCE

Should you require assistance regarding this product and its operation, please
contact our customer care department at 541-868-8205 or via email at
[e-mail].

WARRANTY

This product is warranted to be free of manufacturing defects for a period of 3
months from date of retail purchase. Defective product should be directed to the

place of retail purchase for exchange. Should this not be possible, contact our
customer care department for assistance and a return material authorization. No

returns may be made without a return authorization. Please retain your retail
receipt as you may be asked to provide a copy of it for proof of date purchased.

This warranty does not cover product subjected to abuse, misuse, accidental
damage or tampering.

Upon return of the defective product, Oregon Scientific will at its discretion,
replace the product with either a new or a tested reconditioned product. Should
the product be out of warranty, the consumer may purchase directly from Oregon
Scientific a replacement at reasonable cost plus shipping and handling.