Oregon BAR998HGN User Manual

CONTENTS

Introduction ................................................................. 2

About Oregon Scientific............................................ 3

Product Overview ....................................................... 3

LCD Screen ............................................................. 3

Top View .................................................................. 4

Back View ................................................................ 4

Remote Sensor (RTGR328N).................................. 5

Getting Started ............................................................ 5

Batteries................................................................... 5

AC Adapter (Main Unit)............................................ 6

Change Settings ...................................................... 6

Tilt the Display ......................................................... 6

Remote Sensor ........................................................... 6

Thermo / Hygro Sensor Setup (RTGR328N)........... 7

Fold Out Stand ........................................................ 7

Clock........................................................................ 8

Set Radio Signal Format.......................................... 8

Sensor Data Transmission ......................................8

Sensor Search ......................................................... 8

Clock and Calendar .................................................... 9

Radio-Controlled Clock............................................ 9

Turn Radio-Controlled Clock ON/OFF..................... 9

Set Clock .................................................................9

World City Display .................................................10

Alarms........................................................................ 10

Set Daily Alarm ...................................................... 10

Set Pre-Alarm ........................................................ 11

Activate Alarm ........................................................ 1 1

Snooze .................................................................. 11

Barometer .................................................................. 12

View Barometer Area............................................. 12

Select Measurement Unit ......................................12

View Barometer History ......................................... 12

Bar Chart Display................................................... 12

Set Altitude............................................................. 12

Weather Forecast...................................................... 13

Weather Forecast Icons......................................... 13

UV Measurement (with optional UVR138) .............. 13

Temperature and Humidity ...................................... 14

View Temperature and Humidity Area ................... 14

Select Measurement Unit ......................................14

Select Sensor Channel .......................................... 14

Minimum / Maximum Records ............................... 14

Temperature and Humidity Trend .......................... 14

Comfort Zone......................................................... 15

Heat Index .............................................................15

Heat Index Levels .................................................. 15

View Min / Max Heat Index Levels......................... 15

Voice Recognition.....................................................16

Activate Voice Recognition Prompt .......................16

Set Volume Level................................................... 16

Voice Recognition Commands...............................16

1

EN

EN

Tips for Using Voice Recognition........................... 16

Backlight.................................................................... 17

Reset System ............................................................17

Safety and Care......................................................... 17

Warnings....................................................................17

Troubleshooting........................................................ 18

Specifications ........................................................... 18

Main unit dimensions ............................................. 18

Remote unit dimensions ........................................ 18

Temperature........................................................... 19

Relative humidity ...................................................19

Barometer .............................................................. 19

Remote unit (RTGR328N) ..................................... 19

Radio controlled clock ........................................... 19

Power..................................................................... 19

EC Declaration of Conformity.................................. 20

INTRODUCTION

Thank you for selecting the Oregon Scientific™
BAR998HGN/BAR993HGN Voice Activated Wireless

Weather Station. This powerful device bundles voice
recognition, time keeping, and weather monitoring features
into a single tool you can use from the convenience of
your home. In this box, you will find:

• Main unit

• Remote sensor (RTGR328N)

• Optional UV sensor (UVR138)

• AC adapter

• Batteries

BAR998HGN — BAR998HGN Main unit + RTGR328N
Remote sensor

BAR993HGN — BAR998HGN Main unit + RTGR328N
Remote sensor + UVR138 UV Sensor

Keep this manual handy as you use your new product. It
contains practical step-by-step instructions, as well as
technical specifications and warnings you should know.

2

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientific.com) to learn more
about other Oregon Scientific products such as digital
cameras, projection clocks, health and fitness gear, and
weather stations. The website also includes contact
information for our customer service department, in case
you need to reach us.

PRODUCT OVERVIEW

LCD SCREEN

1. Clock / Alarm Area: Radio controlled clock; alarms

2. UVI / Barometer Trend Area: UV level and barometric
pressure bar chart

3. UVI / Barometric Measurement Area: UV Index and
barometric readings

4. Temperature / Heat Index Area: Readings and trend
lines; sensor channel number; battery status

5. Humidity / Comfort Zone Area: Readings and trend
lines; comfort zone

6. Microphone for Voice Recognition

7. World Cities Area: current, sunrise, sunset, moon
rise, and moon set times for 130 cities

8. Weather Forecast Area: Animated weather forecast

9. Calendar Area: Calendar, voice recognition icon, AC
power icon

3

EN

EN

TOP VIEW

1. MODE – change settings / display

2. ALARM / – view alarm status; set alarm

3. HISTORY – view historical barometer and UV
readings

4. SNOOZE / LIGHT – activate 8-minute snooze or
backlight

5. CHANNEL – switch remote sensor

6. MEMORY – view current and saved temperature,
humidity and heat index readings

7. SELECT – switch Areas

BACK VIEW

1. UP – increase setting / activate radio-controlled clock
and voice recognition

2. DOWN – decrease setting / deactivate radio-
controlled clock and voice recognition

°C / °F

3.

4. Barometer unit (mb/inHg)

5. RESET

6. Battery case release button

7. Battery compartment

8. AC Adaptor plug

4

REMOTE SENSOR (RTGR328N)

1. LCD display

2. LED Status indicator

3. Ventilation duct

EN

1. Signal reception

2. Channel number

3. Low battery icon

4. Time

1
2

5. Temp (°C or °F)

6. Humidity %

7. Temp / Humidity

1

2
3

4

5
6
7

1. Wall mount

2. Channel switch (1 – 5)

3. RESET

4. °C / °F

5. Search

6. EU/UK radio signal
format switch

7. Battery compartment

8. Fold-out stand

3

1
2
3
4
5
6

7

8

GETTING STARTED

BATTERIES

Insert batteries before first use, matching the polarity as
shown in the battery compartment. For best results,
install batteries in the remote sensor before the main unit.
Press RESET after each battery change.

Do not use rechargeable batteries.

NOTE

shows when batteries are low.

UNIT
Main Calendar Area
Remote Temp / Heat Index Area
UV Sensor UVI / Barometric

5

LOCATION

Measurement Area

EN

AC ADAPTER (MAIN UNIT)

The AC power adapter socket is located at the bottom of
the main unit. Batteries are for back-up purposes only;
the adapter is required for Voice Recognition.

shows in the Weather Forecast Area when AC

adapter is not plugged in.

CHANGE SETTINGS

1. Press SELECT to
switch between

Areas. ▲ indicates
the selected Area.

2. Most Areas have alternate display options (for
example, Clock / Alarm or Barometer / UVI).
Press MODE to switch options, or ALARM to switch
between Clock and Alarm.

3. Press and hold MODE for 2 seconds to enter setting
mode.

4. Press UP or DOWN to change settings.

5. Press MODE to confirm.

TILT THE DISPLAY

You can tilt the display
back for better viewing or
audio sound. Hold the base
of the unit with your hand,
and then gently push the
top back.

REMOTE SENSOR

This product is shipped with the RTGR328N Thermo/Hygro
Sensor and an optional UVR138 Ultraviolet Sun Ray
Sensor. The main unit can collect data from up to 6 sensors
(5 Thermo / Hygro Sensors and 1 UV Sensor). (Additional
sensors sold separately.)

The RTGR328N Sensor collects temperature and humidity
readings, and signals from official time-keeping
organizations for the radio-controlled clock.

For information about the UVR138, refer to the UVR138
User Manual.

6

THERMO / HYGRO SENSOR SETUP (RTGR328N)

1. Open the battery compartment with a small Phillips
screwdriver.

2. Insert the batteries.

3. Set the channel and radio signal format. The
switches are located in the battery compartment.

SWITCH OPTION
Channel Channel 1 – 5. If you are using

more than one sensor, select a
different channel for each sensor

Radio Signal EU (DCF) / UK (MSF)
Format

4. Press RESET. Then set the temperature unit.

SWITCH OPTION
Temp °C / °F

5. Close the battery compartment.

6. Secure the sensor with the wall mount or using the
fold-out stand.

FOLD OUT STAND

1. Fold-out the stand

2. Lock it into place

1

2

For best results:

• Insert the batteries and select the unit, channel, and
radio signal format before you mount the sensor.

• Place the sensor out of direct sunlight and moisture.

• Do not place the sensor more than 70 meters

(230 feet) from the main (indoor) unit.

• Position the sensor so that it faces the main (indoor)
unit, minimizing obstructions such as doors, walls,
and furniture.

• Place the sensor in a location with a clear view to
the sky, away from metallic or electronic objects.

NOTE

The transmission range may vary and is

subject to the receiving range of the main unit.

Y ou may need to experiment with various locations to get
the best results.

7

EN

EN

CLOCK

This remote sensor can automatically synchronize the date
and time with official time-keeping organizations in
Frankfurt (Germany) and Rugby (England). When the
sensor is within 1500 km (932 miles) of a RF signal, the
reception icon will blink during reception.
When the sensor receives the radio-controlled clock signal
and is paired with the main unit, the clock in the main unit
will be automatically updated.

SET RADIO SIGNAL FORMAT

The RADIO SIGNAL FORMAT switch is located inside
the battery compartment. Select EU (DCF) or UK (MSF).
Then, press RESET.

Reception takes 2 – 10 minutes to complete. Once
complete, the icon will stop blinking.

STRONG SIGNAL WEAK OR NO SIGNAL

OR

To force a manual RF clock reception, press and hold

SEARCH for 2 seconds.

SENSOR DATA TRANSMISSION

Data is sent from the sensor(s) every 60 seconds. The
reception icon shown in the T emperature / Heat Index Area
indicates the status.

ICON DESCRIPTION





--- shows in Temp / The selected sensor
Humidity Areas cannot be found.

SENSOR SEARCH

T o search for a Thermo / Hygro sensor, press SELECT to
navigate to the T emperature/ Heat Index Area. ▲ will show
in the lower right corner of the Area. Then, simultaneously
press and hold MEMORY and CHANNEL for 2 seconds.

To search for the UV sensor, press SELECT to navigate
to the UVI / Barometric Trend Area. ▲ will show in the
lower left corner of the Area. Then, press and hold

MEMORY and CHANNEL for 2 seconds.

NOTE

If the sensor is still not found, check the batteries.

8





Main unit is
searching
for sensors.

At least 1 channel
has been found.

Sensor 1 is sending
data. (The number
shows which sensor
is selected.)

Search for the sensor
or check batteries.

CLOCK AND CALENDAR

This product tracks the time and date for 1 local location,
and 1 world city that you choose. The information is shown
in the top left and bottom right areas of the display.

RADIO-CONTROLLED CLOCK

The time and date are automatically updated by radio
controlled clock signals from official time-keeping
organizations in Frankfurt (Germany) and Rugby (England)
unless you disable this feature. The signals are collected
by the remote sensor (RTGR328N) whenever it is within
1500 km (932 miles) of a signal.
Initial reception takes 2 – 10 minutes, and is initiated when
you first setup the unit, and whenever you press RESET.
Once complete, the reception icon will stop blinking.

The icon shown in the Clock Area indicates 2 factors:

• Connection between the main unit and the sensor
that collects RF signals ( )

• RF signal reception ( )

Both parts will show ( ) when the sensor that receives
RF signals is selected and the RF signal is strong. (If you
select another sensor, or will show to indicate
whether the RF signal is strong.)

If no signal is found, check the sensor batteries.

TURN RADIO-CONTROLLED CLOCK ON/OFF

If you wish to manually set the clock, you must first disable
the radio-controlled feature. To do this, navigate to the
Clock / Alarm Area. Then, press and hold DOWN on the
main unit for 2 seconds. T o enable it, navigate to the Clock
/ Alarm Area, then press and hold UP for 2 seconds.

The house icon
indicates that the
radio-controlled
clock is ON. No
icon means that
it is OFF.

SET CLOCK

You only need to do this if you have disabled the radio
controlled clock, or if you are too far from a RF signal.

1. Press SELECT to
navigate to the Clock
Area. ▲ will show in
the lower left corner
of the Area.

2. Press and hold MODE
for 2 seconds. The
Clock and World
City Areas will blink.

3. Press UP or DOWN to choose the city you are
LOCATED IN. Press and hold for rapid search.

4. Press MODE again.

9

EN

EN

5. Select the 12/ 24 hour format, hour, minute, year,
date/month format, month, date, display language,
and (optional) volume level for the Voice
Recognitionfeature. Press UP or DOWN to change
the setting. Press MODE to confirm.

NOTE

The language options are (E) English, (F)
French, (D) German, (I) Italian, and (S) Spanish. The
language you select determines the weekday display
and the spoken language for the Voice Recognition
prompts.

NOTE

Voice Recognition must be activated (16)
before you can set the volume level. The number of

bars shown after the icon (
(Low, Medium, or High).

WORLD CITY DISPLAY

With this product, you can
view the current, sunrise,
sunset, moonrise, and
moon set times for up to
130 world cities.

1. Press SELECT to navigate to the World Clock Area.

2. T o scroll through the information for the selected city,
press MODE.

) indicates the level

3. To select another city, press and hold MODE for 2
seconds. Then, press UP or DOWN to select the
3-digit code for the city. For a list of W orld City Codes,
refer to the enclosed sheet.

4. Press MODE again when you are finished.

ALARMS

This product has 2 alarms: the Daily Alarm and a Pre
Alarm for snowy weather. The Daily Alarm can be set to
go off at the same time every day. The Pre-Alarm sounds
only when the Daily Alarm is activated and the recorded
temperature from Channel 1 Sensor falls to 2°C (35.6 °F)
or below.

SET DAILY ALARM

1. Press SELECT to navigate to the Clock Area. ▲ will
show in the lower left corner of the Area.

2. Press ALARM /
at the top.)

3. Press and hold ALARM /

4. Select the hour and minute. Press UP or DOWN to
change settings. Press ALARM /

shows when the Alarm is set.

10

to view the Alarm. (AL will show

for 2 seconds.

to confirm.

SET PRE-ALARM

The Pre-Alarm can be set to sound 15,30,45, or 60 minutes
before the Daily Alarm. It will sound whenever the recorded
temperature from Channel 1 Sensor falls to 2°C (35.6°F)
or below.
For example, if you set the Alarm to 7:00 AM, and the Pre
Alarm to 45 minutes, the Pre-Alarm will sound at 6:15 AM
provided the outdoor temperature at Channel 1 Sensor is
2°C or below.

1. Set up and activate the Daily Alarm.

2. Press ALARM /
(

3. Press and hold ALARM /

4 . Press UP or DOWN to select 15, 30, 45 or 60 minutes.

This is the amount of time the Pre-Alarm will sound
BEFORE the Daily Alarm. The Pre-Alarm is
automatically activated when you select a time.

5. Press ALARM /

shows when the Pre-Alarm is set.

NOTE

The daily Alarm will NOT function until the
next day once if the Pre-Alarm has been triggered.
Also, if you deactivate the Alarm, the Pre-Alarm is also
automatically deactivated.

to switch to Pre-Alarm view.

will show at the top.)

for 2 seconds.

to confirm.

ACTIVATE ALARM

Navigate to the Clock
Area, then press ALARM

to switch to Daily

/
Alarm or Pre Alarm view.
To activate or deactivate
the alarm, press UP or DOWN.

When the Alarm time is reached, the crescendo alarm will
sound for 2 minutes. Press any key to silence the alarm.
It will sound at the same time the next day.

ICON DESCRIPTION

Daily Alarm is activated and will
sound at the set time.

Pre-Alarm is activated and will
sound at the specified time if the
temperature falls to 2°C or below
(35.6 °F).

-:— Alarm is not activated and will

SNOOZE

Press SNOOZE / LIGHT to temporarily disable the Alarm
for 8 minutes.

11

not sound.

or will blink while Snooze is on.

EN

EN

BAROMETER

This product tracks fluctuations in barometric pressure to
provide the weather forecast (13), and the current and
past 24 hours barometric pressure history. Measurements
are recorded by the main (indoor) unit.

VIEW BAROMER AREA

Press SELECT to navigate to the Barometer Area.

is NOT shown, press MODE.

If

Barometric data is
shown in two areas.
The top area shows
a 24-hour bar chart.

The bottom area
shows current and
historical readings.

SELECT MEASUREMENT UNIT

Press mb / inHg on the back of the weather station.

VIEW BAROMETER HISTORY

Navigate to the Barometer Area, then press HISTORY
repeatedly to scroll through the measurements. The
number shown in the HR box indicates how long ago each
measurement was taken (e.g., 2 hours ago, 3 hours ago,
etc.).

BAR CHART DISPLA Y

The bar chart visually shows
atmospheric changes from
the current hour [0] to
24 hours prior (-24).

SET ALTITUDE

Set the altitude to match how far above or below sea level
you are living. This ensures that the barometric pressure
readings are accurate.

1. Navigate to the Barometer Area.

2. Press and hold HISTORY for 2 seconds.

3. Press UP or DOWN to set the altitude in 10 meter
increments (-100m to 2500m).

4. Press HISTORY to confirm.

12

WEATHER FORECAST

This product forecasts the next 12 to 24 hours of weather
within a 30 – 50 km (19 – 31 mile) radius. The forecast is
based on barometric pressure trend readings.

The middle area
shows an animated
icon indicating the
forecasted weather.

WEATHER FORECAST ICONS

ICON DESCRIPTION

CLEAR

DAY NIGHT

PARTLY CLOUDY

DAY NIGHT

CLOUDY

RAINY

SNOWY

NOTE

The nighttime icon displays from 6 PM to 6 AM.
When the Channel 1 sensor records a temperature of 2°C
(35.6 °F) or lower, the RAINY icon becomes SNOWY.

UV MEASUREMENT
(WITH OPTIONAL UVR138)

With the optional UVR138 Ultra-Violet Radiation Sensor,
the following information is at your fingertips:

• 10-hour Ultra-violet index (UVI) record

• Automatic calculation of acceptable UV exposure

times based on pre-set user profiles (4 users
maximum)

• UVI Danger Alert when UV index reaches unsafe

levels

UV data is shown in the same area as the Barometer. Press

SELECT to navigate to the Barometer Area, then press
MODE to display the

UVR138 User Manual for more information.

13

UV icon and data. Refer to the

EN

EN

TEMPERA TURE AND HUMIDITY

The weather station can display the following information
from any of the 5 remote sensors:

• Current, minimum, and maximum temperatures and
relative humidity percentages.

• Heat index that shows the apparent, or felt, current
temperature, trend line, and minimum / maximum
readings.

• Comfort level indicator and trend line (rising, falling,
or steady).

Data is collected and displayed every 60 seconds.

VIEW TEMPERATURE AND HUMIDITY AREA

Press SELECT to navigate to the Temperature and
Humidity Areas.

Temperature and Heat Index
data is given at the top;
Humidity is below.

SELECT MEASUREMENT UNIT

°C / °F on the back of the weather station.

Press

SELECT SENSOR CHANNEL

Press CHANNEL to switch between sensors 1 - 5.

The house icon shows the
selected remote sensor.

T o auto-scan between sensors, press and hold CHANNEL
for 2 seconds. Each sensor’s data will be displayed for
3 seconds.To end auto-scan, press CHANNEL or

MEMORY with the Temperature / Humidity Area selected.

NOTE

If you select a sensor that collects only

temperature data, the humidity will not be shown.

MINIMUM / MAXIMUM RECORDS

Press MEMORY repeatedly to
view current, maximum and
minimum records for the selected
sensor. To clear the records, press
and hold MEMORY for 2 seconds.
A beep will sound to confirm that
the memory has been cleared.

TEMPERATURE AND HUMIDITY TREND

The trend lines are shown next to the Temperature and
Humidity readings.

Trend Rising Steady Falling
ICON

14

COMFORT ZONE

The Comfort Zone indicates how comfortable the climate
is, based on current temperature and humidity
measurements.

ZONE TEMPERATURE HUMIDITY

Any >70%
20 – 25 ° C 40 – 70%

(68 - 77 ° F)
Any <40%

This information is shown in the Humidity Area when the
current measurement is displayed.

HEAT INDEX

The Heat Index indicates apparent, or felt, temperature.
This can significantly differ from measured temperatures
on hot, low humidity days since it estimates the effects of
heat stress (temperature and humidity) on the body.

To view the Heat Index,
press MODE while the
Temperature and Humidity
Area is selected.

HEAT INDEX LEVELS

IF THE THEN THE DANGER LEVEL
HEAT FOR PROLONGED OUTDOOR

27 to 32°C CAUTION
(80 to 89°F) (possible heat fatigue)

32 to 40°C EXTRA CAUTION
(90 to 104°F) (possible sunstroke, heat cramps,

41 to 54°C DANGER
(105 to 129°F) (likely sunstroke, heat cramps, or

54 to 93°C VERY DANGEROUS
(130 to 199°F) (possible heat stroke or sunstroke)

“HH” OVER RANGE

VIEW MIN / MAX HEAT INDEX LEVELS

Press MEMORY while the Heat Index Area is shown.

15

INDEX IS PHYSICAL ACTIVITY IS

or heat exhaustion)

heat exhaustion; possible
heat stroke)

(the temperature falls outside the
26 to 93°C (80 to 199°F) range)

EN

EN

VOICE RECOGNITION

This product has a built-in sensor for recognizing voice
commands. When activated, the product can tell you the
current time, alarm, and weather conditions in response
to a voice command that you give it.

The language for the Voice Recognition feature is selected
when you set the clock ( 9).

ACTIVATE VOICE RECOGNITION PROMPT

Plug in the AC power adapter (it must be plugged in for
the feature to work). Press SELECT to navigate to the
Clock Area. Then, simultaneously press and hold UP and
DOWN for 3 seconds. A welcome message in the selected
language will broadcast.

displays
when Voice
Recognition is ON

SET VOLUME LEVEL

There are 3 volume levels: Low, Medium and High. To set
the volume level, first activate Voice Recognition.

will display. ) Then, access the Clock Settings

(
Mode to select the volume level ( 10, Step 5).

VOICE RECOGNITION COMMANDS

The product responds to the following voice commands:

COMMAND RESPONSE
WEATHER STATION Prepares to access

ALARM Alarm status (on or off)

TIME Current time
WEATHER Weather forecast,

TIPS FOR USING VOICE RECOGNITION

Face the product, no more than 2 meters (6 feet) away.
Speak slowly and distinctly. Minimize background noises,
such as the television or other people talking. If the weather
station does not recognize your command, it will ask you
to repeat it. After 2 unsuccessful attempts you will hear a
beep. To begin again, say “Weather Station” to re-enter
the program, then repeat the command.

The product will not respond to any command when it is
talking. Say command only when it has finished.

16

weather station data.
Further command is
needed.

and setting

current temperature
and humidity for
selected sensor.

BACKLIGHT

Press SNOOZE / LIGHT to illuminate the backlight for 5
seconds.

RESET SYSTEM

The RESET buttons are located on the back of the main
unit and in the battery compartment for the sensors. Press
RESET when you change the batteries and whenever
performance is not behaving as expected (for example,
unable to establish radio frequency link with remote unit
or radio-controlled clock).

NOTE

When you press RESET, all settings will return

to default value, and you will lose all stored information.

SAFETY AND CARE

Clean the unit with a slightly damp cloth and alcohol- free
mild detergent. Avoid dropping the unit or placing it in a
high-traffic location.

WARNINGS

This product is designed to give you years of service if
handled properly. Observe the following guidelines:

• Never immerse the unit in water. This can cause
electrical shock and damage the unit.

• Do not subject the main unit to extreme force,
shock, or fluctuations in temperature or humidity.

• Do not tamper with the internal components.

• Do not mix new and old batteries or batteries of

different types.

• Do not use rechargeable batteries with this product.

• Remove the batteries if storing this product for a

long period of time.

• Do not scratch the LCD display.

Do not make any changes or modifications to this product.
Unauthorized changes may void your right to use the
product. The technical specifications of this product and
contents of this user guide are subject to change without
notice. Images not drawn to scale.

17

EN

EN

TROUBLESHOOTING

Check here before contacting our customer service
department.

Problem Symptom Remedy
Barometer Strange Set altitude / unit

Calendar Strange date Change language

Clock Cannot adjust Disable radio-

T emp Shows “LLL” Temperature is

Remote Cannot Check batteries
sensor locate remote ( 5)

readings ( 12)

/ month ( 9-10)

clock controlled clock

( 9)

Cannot auto- Adjust batteries.
synch ( 5)

Press RESET
( 17)
Manually activate

radio-controlled
clock ( 8)

or “HHH” out-of-range

sensor

Check location ( 7)

Cannot change Check sensors.
channel Only one sensor is

working ( 8)

Problem Symptom Remedy
Voice Does not work Is the AC adapter

recognition plugged in? ( 6)

SPECIFICATIONS

MAIN UNIT DIMENSIONS

L x W x H 207 x 119 x 40 mm

Weight 406 grams (0.9 lbs) with

REMOTE UNIT DIMENSIONS

L x W x H 70 x 24.5 x 116mm

Weight 156 grams (0.34lb.) with

18

(8,15 x 4.69 x 1.58 inches)

battery

(2.76 x 0.96 x 4.57 inches)

battery

Is voice recognition
on? ( 16)

Try again once the
product has
stopped talking.
Speak clearly and
slowly.

TEMPERATURE

Unit °C or °F
Indoor Range -5 °C to 50 °C

(23 °F to 122 °F)

Outdoor Range -20 °C to 60 °C

(-4 °F to 140 °F)
Resolution 0.1 °C (0.2° F)
Comfort 20 °C to 25 °C

(68 °F to 77 °F)
Memory Min / Max
Trend +/- 5° (°C or °F)

RELATIVE HUMIDITY

Range 25% to 95%
Resolution 1%
Comfort 40% to 70%
Memory Min / max
Trend +/- 3%

BAROMETER

Unit mb/hPa or inHg
Range 500 to 1050 mb

(14.77 to 31.01 inHg)
Resolution 1 mb (0.03 inHg)
Altitude -100 to 2500 meters

(-328 to 2734 feet)
Display Sunny, partly cloudy, cloudy, rainy,

snowy

REMOTE UNIT (RTGR328N)

RF frequency 433 MHz
Range Up to 70 meters (230 feet)

Transmission every 1 minute
Channel No. 1, 2, 3,4 or 5
Unit °C or °F

RADIO CONTROLLED CLOCK

Synchronization Auto or disabled
Clock display HH:MM:SS
Hour format 12hr AM/PM (MSF format)

Calendar DD/MM or MM/DD;

Alarm Daily & Pre-Alarm; 2- minute

Snooze 8 minutes

POWER

Main unit
Power adapter 6V AC adapter
Batteries 3 x UM-3 (AA) 1.5V alkaline

Thermo-Hygro
Remote sensor 2 x UM-3 (AA) 1.5V alkaline batteries

19

with no obstructions

24hr (DCF format)

weekday in 5 languages (E, G, F, I,S)

crescendo

batteries (back-up)

EN

EN

EC-DECLARATION OF CONFORMITY

This product
Article 3 of the R&TTE 1999/5/EC Directives,if used for its
intended use and that the following standard(s) has/have
been applied:

Radio frequency spectrum
(Article 3.2 of the R&TTE Directive)

applied standard(s)

complies with the essential requirements of

ETSIEN300220-3(Ver.1.1.1):2000-09

Additional information:
The product therefore conforms with the Low Voltage
Directive 73/23/EC,the EMC Directive 89/336/EC and
R&TTE Directive 1999/5/EC (appendix II) and carries the
respective CE marking.

Electromagnetic compatibility
(Article 3.1.b of the R&TTE Directive)

applied standard(s)

ETSIEN301489-1-3(Ver.1.4.1):2002-08

Safety of information technology equipment
(Article 3.1.a of the R&TTE directive)

applied standard(s)

EN 60950:2000

Carmelo Cubito
Agrate Briznaza (MI) / Italy January 2004

EC Representative of Manufacturer

COUNTRIES RTTE APPROVAL COMPLIED

All EC Countries, Switzerland

20

and Norway

CH

N