Oreck UPRO18T User Manual
40337-01 REV A
S IMP L Y AMAZ ING
®
USER
’
S GUIDE
PROFESSIONAL
GRADE
COMMERCIAL
UPRO14T
UPRO18T
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
Commercial: 800-242-1378
Hospitality: 888-236-7325
Canada: 866-746-7325
www.commercial.oreck.com
Table of Contents
Maintenance and Customer Service,
Grounding Instructions, Important Safety Instructions . page 2
Warranty, Troubleshooting Guide . . . . . . . . . . . . . . . . . page 3
Parts List,
Installing Power Cord, Operating Instructions . . . . . . . page 5
General Information,
To Replace Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
To Clean or Replace Inlet Filter,
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
BEFORE OPERATING CLEANER,
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
Maintenance and Customer Service
Your Oreck vacuum cleaner is a product of precise engineering. The
motor bearings are permanently lubricated and should not be oiled. If
you require additional information or have problems with your Oreck
appliance, you may call ORECK Commercial Customer Service at:
Commercial: 800-242-1378
Hospitality: 888-236-7325
Canada: 866-746-7325
Please specify the model number and serial/code number which can
be found on the data plate on the back of the vacuum.
Save your sales or purchase slip. Should your Oreck appliance
require warranty service in the U.S.A., present this slip to the
Authorized Service Center as your proof of purchase date or, in
Canada, call customer service.
Grounding Instructions
This appliance must be grounded. If it should malfunction or break
down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electric shock. The cord for this
appliance has an equipment-grounding conductor and a grounding
plug. It must only be plugged into an electrical outlet that is properly
installed and grounded in accordance with all local codes and
ordinances. Do not modify plug provided with appliance.
DANGER: Improper connection of the equipment-grounding
conductor can result in a risk of electrical shock. Check with a
qualified electrician or service person if you are in doubt as to
whether the outlet is grounded. If not, have a proper outlet installed
by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit. It has a
grounding plug similar to the example shown. Make sure the
appliance is connected to an outlet
with the same configuration
as the plug. No adapter should be
used with this appliance.
Grounded Outlet
Grounding Pin
• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary
• Use only as described in this manual. Use only manufacturer’s
• Do not leave appliance unattended when plugged in. Unplug from
• Connect to a properly grounded outlet only. See: Grounding
• Do not use with damaged cord or plug.
• If vacuum cleaner is not working as it should, has been dropped,
• Do not pull or carry by cord, use cord as a handle, close door on
• Do not run vacuum over cord.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening
• Keep hair, loose clothing, fingers and all parts of body away from
• Do not use to pick up anything that is burning or smoking, such as
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
•
•
• Do not use appliance in an enclosed space where flammable,
• Do not pick up toxic material such as chlorine bleach, drain cleaner,
•
WARNING
To reduce the risk of fire,
electric shock, or injury:
when used by or near children.
recommended attachments.
outlet when not in use and before servicing.
Instructions.
damaged, left outdoors, or dropped into water, return it to a service
center or call customer service at:
Commercial: 800-242-1378
Hospitality: 888-236-7325
Canada: 866-746-7325
cord, or pull cord around sharp edges or corners. Keep cord away
from heated surfaces.
the cord.
blocked; keep free of dust, lint, hair and anything that may reduce
air flow.
openings and moving parts.
cigarettes, matches, or hot ashes.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible liquids, such as
gasoline or lighter fluid, or use in areas where they may be present.
explosive or toxic vapors are given off by oil base paint, paint thinner,
some mothproofing substances, or in an area where flammable
dust is present.
gasoline, etc. with this appliance.
Use caution when vacuuming over area rugs edges and fringe.
SAVE THESE INSTRUCTIONS
For Commercial Use
2
Warranty
Troubleshooting Guide
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing
Company gives you the following limited warranty for this product
only if it was originally purchased for commercial use, not resale from
Oreck or an Oreck
Authorized Retail Dealer.)
Oreck will repair or replace, free of charge, to the original purchaser,
any part that is found to be defective in material or workmanship within
two (2) years. This limited warranty applies to commercial use.
Drive belts, revolving brushes, disposable bags, and other parts subject
to normal wear are not covered by this limited warranty.
This limited warranty does not apply to any part subjected to accident,
abuse, alteration, misuse, damage caused by fire or act of God, or
the use of voltages other than indicated on the serial number plate of
this product or service of this product by other than Oreck or an
Oreck Factory Authorized Service Center.
Oreck does not authorize any person or representative to assume or
grant any other warranty obligation with the sale of this product.
Oreck’s limited warranty is valid only if you retain proof of purchase
from Oreck or an Oreck Authorized Retail Dealer for this product. If
you purchase this product from any other source, your purchase is
“AS IS,” which means Oreck grants you no warranty
, and that you,
not Oreck, assume the entire risk of the quality and performance of this
product, including the entire cost of any necessary servicing or repairs
of any defects.
Oreck’s liability for damages to you for any costs whatsoever arising
out of this statement of limited warranty shall be limited to the amount
paid for this product at the time of original purchase. Oreck shall not
be liable for any direct, indirect, consequential or incidental damages
arising out of the use or inability to use this product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not
apply to you.
ALL EXPRESSED AND IMPLIED WARRANTIES FOR THIS
PRODUCT, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD, AND NO WARRANTIES, WHETHER EXPRESS OR
IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied
warranties, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
WARNING: Unplug cord from electrical outlet
before servicing.
PROBLEM POSSIBLE SOURCE AREAS TO CHECK
VACUUM MOTOR IS OFF
BRUSH MOTOR IS OFF
RED LIGHT ON
RED & GREEN LIGHT ON
FULL BAG INDICATOR
FLASHES
LOW SUCTION
POOR PICK UP
Not plugged in properly.
No electricity in wall
outlet.
Switch in off position.
Sensor temperature
too high.
Faulty switch.
Not plugged in properly.
Handle in upright
position.
Wand not installed
properly.
Brush motor obstructed.
Brush drive belt broken.
Dust bag full.
Hose and wand
blocked.
Power brush inlet
blocked.
Inlet filter blocked.
Deflector port sealing
in top of housing.
Dust bag full.
Full bag indicator
flashes.
Wand not installed
properly.
Brush not adjusted
.
correctly
Brush worn.
Be sure plug is firmly
plugged into wall outlet.
Check electrical source
(fuse or circuit breaker).
Position switch to on
position.
Check for air obstruction.
Let the motor cool
down.
Replace switch.
Return to Service
Center for repair.
Be sure plug is firmly
plugged into wall outlet.
Activate foot pedal to
lower handle to engage
brush motor switch.
Remove and re-install
wand per instructions
(page 5).
Unplug machine and
inspect for obstruction.
Return to Service
Center for repair.
Return to Service
Center for repair.
Replace dust bag.
Inspect for obstruction.
Inspect for obstruction.
Clean or replace inlet
filter.
Check for free
movement.
Replace dust bag.
See “Dust Full Bag
Indicator Flashes”.
Re-install wand.
Adjust brush height
knob to conform to
carpet thickness (pile).
Return to Service
Center for repair
Replace brush.
.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
FOR SERVICE CALL
Commercial: 800-242-1378
Hospitality: 888-236-7325
Canada: 866-746-7325
Whenever calling, please be sure to have your model and serial
number from data plate.
3
Loading...