OPTREX DMF5010NF-FW Datasheet
LCD Module Specification
First Edition
Apr 18, 2000
Final Revision
*******
Approved by
Checked by
Checked by
Production Div.
Quality Assurance Div.
Design Engineering Div.
Type No.
ＤＭＦ５０１０ＮＦ－ＦＷ
ＤＭＦ５０１０ＮＦ－ＦＷ
ＤＭＦ５０１０ＮＦ－ＦＷＤＭＦ５０１０ＮＦ－ＦＷ
Table of Contents
Prepared by
1. General Specifications .............................................................................2
2. Electrical Specifications...........................................................................3
3. Optical Specifications..............................................................................7
4. I/O Terminal.............................................................................................9
5. Test..........................................................................................................11
6. Appearance Standards............................................................................12
7. Code System of Production Lot ..........................................................15
8. Type Number..........................................................................................15
9. Applying Precautions .............................................................................15
10. Precautions Relating Product Handling................................................16
11. Warranty..................................................................................................17
Revision History
Rev. Date Page Comment
Production Div.
DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION Page 1/17
OPTREX
1.General Specifications
Operating Temp.
Storage Temp.
Dot Pixels
Dot Size
Dot Pitch
Viewing Area
Outline Dimensions
W eight
LCD Type
Viewing Angle
Control LSI
Data Transfer
Backlight
Additional Spec.
CFL light unit is replaceable.
Drawings
min. 10℃ ～ max. 40℃
：
min. -20℃ ～ max. 60℃
：
240 (W) × 64 (H) dots
：
0.49 (W) × 0.49 (H) mm
：
0.53 (W) × 0.53 (H) mm
：
132.0 (W) × 39.0 (H) mm
：
200.0
：
250g max.
：
NTD-7580
：
6:00
：
T6963C-0101 (Produced by TOSHIBA)
：
8-bit parallel data transfer
：
Cold Cathode Fluorescent Lamp (CFL) × 1
：
Holder and PWB ground are connected by soldering.
：
Dimensional Outline UE-32421C
：
*
(W) × 66.0 (H) × 23.0 max. (D) mm
* Without CFL Cable
( F-STN / Black
&White-mode / Transmissive )
DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION Page 2/17
OPTREX
2.Electrical Specifications
2.1.Absolute Maximum Ratings
Parameter Symbol Conditions Min. Max. Units
=0V
V
SS
Supply Voltage
(Logic)
Supply Voltage
(LCD Drive)
Input Voltage VI
2.2.DC Characteristics
Parameter Symbol Conditions Min. Typ. Max. Units
Supply Voltage
(Logic)
Supply Voltage
(LCD Drive)
High Level
Input Voltage
VCC-VSS
VCC-VEE
VCC-VSS
-0.3 7.0 V
－
0 28.0 V
－
-0.3 VCC+0.3 V
－
Ta=25℃, V
4.5 － 5.5 V
－
SS
=0V
VCC-VEE Shown in 3.1 V
VIH VCC=5.0V±10% VCC-2.2
V
－
V
CC
Low Level
VIL VCC=5.0V±10% 0 － 0.8 V
Input Voltage
High Level
VOH IOH=-0.75mA VCC-0.3
Output Voltage
Low Level
VOL IOL=0.75mA 0 － 0.3 V
Output Voltage
ICC VCC-VSS=5.0V
Supply Current
I
VCC-VEE=13.3V
EE
V
－
8.5 13.0 mA
－
3.0 5.0 mA
－
V
CC
DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION Page 3/17
OPTREX
2.3.AC Characteristics
Parameter Symbol Min. Max. Units
=5.0V±10%
V
CC
C/D Setup Time
C/D Hold Time
CE, RD, WR Pulse Width
Data Setup Time
Data Hold Time
Access Time
Output Hold Time
t
100 － ns
CDS
t
10 － ns
CDH
t
t
t
,
,
CE
t
t
t
t
ACC
80 － ns
RD
WR
80 － ns
DS
40 － ns
DH
10 50 ns
OH
150 ns
－
C/D
CDS
t
CDH
t
CE
CE, tRD, tWR
t
RD, WR
DS
t
DH
t
D0～D7
(WRITE)
ACC
t
OH
t
D0～D7
(READ)
DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION Page 4/17
OPTREX
2.4.Power Supply ON/OFF Sequence
2.4.1.ON Sequence
(Without RESET Signal)
SIGNAL
VCC
SIGNAL
VEE
0≦t
0≦t
LEVEL
VCC
VSS
VCC
VSS
VCC
VSS
VEE
2.4.2.OFF Sequence
LEVEL
VCC
VSS
VCC
VSS
VCC
VSS
0≦t
0≦t
SIGNAL
VCC
SIGNAL
(Without RE S E T Signal)
VEE
VEE
2.4.3.Reset Sequence
SIGNAL
LEVEL
RESET
T>250μs
T≧10 ms
T≧0
VCC
VEE
T≧0T≧0T≧50msT≧50ms
H Level
L Level
VCC
VSS
VCC
Power OffPower On Reset CancellationReset
VEE
Please maintain the above sequence when turning on and off the power supply of the module.
If V
is supplied to the module while internal alternate signal for LCD driving (M) is unstable or
EE
RESET is active, DC component will be supplied to the LCD panel. This may cause damage to
the LCD module.
DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION Page 5/17
OPTREX
2.5.Lighting Specifications
Ta=25℃
Parameter Symbol Conditions Min. Typ. Max. Units Notes
Lamp Voltage VL
Lamp Current IL
Starting Voltage VS
Surface Luminance L IL=5.0mA 400 －
Average Life TAL I
－
4.0 5.0 6.0 mArms 2
－
－
=5.0mA 10000 15000 － hrs 5
L
270 － Vrms 1
－
900 － Vrms 3
－
cd/㎡ 4
－
Note 1 : The voltage ( r.m.s. ) to maintain the electric discharge of the lamp. It is measured after lighting for
3 minutes .
Note 2 : The current ( r.m.s. ) to flow through the lamp with the electric discharge. It i s mea s ured after
lighting for 3 minutes .
Note 3 : The voltage at starting the electric discharge when the voltage is increased gradually from 0V.
Note 4 : Surface Luminance is specified by the initial data of luminance measured at the center of display
surface after 20 minutes power on. ( All ON pattern )
Note 5 : CFL life is defined as the time for which the initial luminance is attenuated by 50% of the
luminance value. Average Life representes the time elapsed at the point of time when the residual
ratio becomes below 50% when plural lamps are lighted in comparison with the definition of life
mentioned above.
I
N
V
VS VL
C
F
L
CFL Testing Circuit
IL
Recommended Inverter : HIU-32 ( Produced by HARISON ) CXA-L10L (DC 12.0V, Produced by TDK)
DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION Page 6/17
OPTREX
Loading...