Optimus EDC-1000, EDC-1022, EDC-1023, EDC-1024, EDC-1050 Installation And Operating Instructions Manual

CONFERENCE

SYSTEM

EDC-1000 SERIES

Installation and operating
instructions

EDC-1000 Version 1.2 Page 1 of 19

EDC-1000 SERIES

Conference System

SAFETY PRECAUTIONS:

¾ Please read this manual carefully before installing and using this unit.

¾ Please keep this manual appropriately for futures questions.

¾ Please read carefully the instruction and warning in this manual.

¾ Please do not use accessories not recommended by dealers.

¾ Please use the attached spare parts accessories provided by the factory only, the factory will

not be responsible for any damage due to false fixing way.

¾ Make sure that the power plug is fixed appropriately and safely.

¾ Please do not use too many extension cables to avoid fire hazard and short circuit.

¾ Please do not insert anything into the unit or spray and liquid on it to avoid short circuit.

¾ If one of the following happen, please contact with maintenance technician:

A. power cable or plug is damaged.

B. water gets into the unit.

C. the unit cannot be operated under normal condition.

D. the unit is dropped onto the ground and damage the frame.

¾ When outdoors equipment or cable is connected into this unit, the grounding of cable system

must be reliable to avoid lightening attack.

¾ Please take care when installing the main control unit and its surrounding facilities.

Avoid strike, fierce swing, which may damage the main conference unit and its surrounding
facilities.

¾ Please do not disassemble the main control unit and its surrounding facilities

A. There are high voltage and sensitive electronic circuits inside the unit. In order to avoid

electric shock, please do not disassemble the equipment. If equipment uncover is
necessary, please seek assistant from qualified technicians.

B. When dealers replacing spare parts, the specification of replacing spare parts should be

acknowledged by manufacturer. Unauthorized spare parts may lead to fire hazard
caused by short circuit.

¾ Please do not block the heat radiating holes on the case.

There is heat sink inside this product. If the heat radiating holes are blocked, the resulting
overheating of the main unit may lead to malfunction.

¾ Use this conference main control unit in environment with the temperature of 0°C ~ 40°C (32°F

~ 104°F) and humidity lower than 90%.

¾ Please do not expose the conference main control unit to rain or humidity, and do not use it in

humid environment.

Please place it at dry place. Humid and water evaporation may lead to the damage of spare
parts inside. Appropriate cover is necessary when placing it outdoor.

¾ Please do not clean the conference main unit and its surrounding facilities with strong or power

detergent.

EDC-1000 Version 1.2 Page 2 of 19

EDC-1000 SERIES

Conference System

If the surface of the unit is dirty, please do not clean it with liquid or spraying detergent, while
slightly wet cloth should be used.

¾ Please do not switch on and off the conference main control unit abruptly.

No matter the unit is running or stop, avoid switch it on and off abruptly to ensure the sensitive
electronic circuit inside not being damaged by abrupt power wave.

¾ Note: When the printed circuit board was going through electric static treatment, correct ESD

safety precaution and grounding should be guaranteed.

¾ Note: Before connecting the unit to the power supply, please adjust the power input according

to the local power specification. Otherwise, unit damage may ensue. The adjusting way can be
seen at Installation and Setting of System.

Warning: Only qualified maintenance staff is allowed to uncover the case of the unit. There
is nothing inside that can be repaired by non certificated technician. Before uncovering the
unit, power should be cut off and no power supply is allowed before the unit is completely
covered.

EDC-1000 Version 1.2 Page 3 of 19

EDC-1000 SERIES

Conference System

1. FOREWORD ................................................................................................................... 4

2. PRODUCT FEATURES .................................................................................................. 5

2.1. Main control unit ……. ........................................................................................... 5

2.2. Chairman unit......................................................................................................... 5

2.3. Delegate unit.......................................................................................................... 5

3. OPERATION AND FUNCTION DESCRIPTION ............................................................. 6

3.1. Introduction to the function of front panel of main unit ........................................... 6

3.2. Function of rear plate of main control unit .............................................................. 7

3.3. Main unit block diagram ......................................................................................... 8

4. INSTALLATION AND SETTING OF THE SYSTEM ....................................................... 9

4.1. Basic installation instruction ................................................................................... 9

4.1.1. Adjust AC power input..........................................................................................9

4.1.2. Basic connection of conference control main unit to chairman/delegate

microphones ........................................................................................................ 9

4.2. Power On............................................................................................................. 10

4.3. LED display and operation................................................................................... 11

4.3.1. MIC CONTROL..................................................................................................11

4.3.2. OVERRIDE.........................................................................................................11

4.3.3. TIME (Voice control-Auto off).............................................................................11

4.3.4. Saving setting.....................................................................................................11

5. MICROPHONE SHAPE AND OPERATION ................................................................. 12

5.1. Table-top chairman unit EDC-1011...................................................................... 12

5.2. Table-top Delegate’s unit EDC-1012 ................................................................... 13

5.3. Flush-mounted Chairman’s unit EDC-1021 ......................................................... 14

5.4. Flush-mounted delegate’s unit EDC-1022 ........................................................... 15

5.5. Flush-mounted Chairman’s unit EDC-1023 ......................................................... 16

5.6. Flush-mounted delegate’s unit EDC-1024 ........................................................... 17

6. SYSTEM SPECIFICATIONS......................................................................................... 18

6.1. EDC-1050 Main control unit specifications .......................................................... 18

6.2. Microphone unit specifications ............................................................................. 19

EDC-1000 Version 1.2 Page 4 of 19

EDC-1000 SERIES

Conference System

1. FOREWORD

This EDC1000 series, the latest and easiest digital conference system with superb performance
and elegant design, can be used for various conferencing.

This conferencing system has the most updated built-in digital module with 10 chairmen
microphones and 75 delegate microphone, providing the unique features of front sound mixing
module, back amplified module, sound effect treatment amplified module to meet your requirement
under any circumstance.

The system will enable self-detection function when the power is on, which can automatically
detect if the function of all the Chairman/ delegate units are normal, facilitating timely function
detection.

High reliability is the utmost importance element in the development of this conference system.
Each conference main control unit and its fittings are all going through careful assembly and strict
test in our ISO 9001 factory. The excellent performance, high reliability and reasonable price make
it the indispensable tools of your conference.

EDC-1000 Version 1.2 Page 5 of 19

EDC-1000 SERIES

Conference System

2. PRODUCT FEATURES

2.1. Main control unit of the conference system

• Digital control capability: Chairman’s unit: 10 pcs, Delegate’s unit: 75 pcs.

• It has 3 setting buttons which can be used to set and change the working mode of the

microphone.

• Built-in front sound mixer amplifier module.

• Built-in power amplifier module.

2.2. Chairman unit

• Desktop, built-in and hand-hold types are available.

• Conference control functions TALK (On/Off) and CONTROL are available.

• It can be placed at any position within the system.

• Maximum 10 chairmen microphone can be installed at the same time.

2.3. Delegate unit

• Desktop, built-in and hand-hold types are available.

• Speech control function such as TALK (On/Off) is available.

• 75 delegate microphones can be installed at the same time.