Visual Verification
Visual Verification
Wi-Fi CAMERA module
Wi-Fi CAMERA module
VXI-CMOD
VXI-CMOD
for VXI-ST/-AM/-DAM
for VXI-ST/-AM/-DAM
Get PDF file and also troubleshooting
information at the following website.
VXI-CMOD
[VXI-ST]
[VXI-AM]
[VXI-DAM]
(Sold separately)
http://navi.optex.net/manual/50262
FEATURES
When the VXI-ST/-AM/-DAM generates an alarm signal,
the VXI-CMOD starts recording a 30 second video clip onto the microSD card.
The clip can then be reviewed via your smart phone from a remote location.
180 degree View Angle
Night vision with strong & wide IR light
Sensor trigger recording function with a 2 second pre-recording
Power from a control panel can be used for both the VXI-CMOD and the VXI-ST/-AM/-DAM
INTRODUCTION
1
No.59-2753-0 1811-09
INSTALLATION & OPERATION MANUAL
EN
Alarm signal
Event record ing
Control Pan el
Newly added
Wi-Fi rout er
Text notification
from a Control Panel
Internet
Visual verification
Smartphone
Connect between terminals of VXI-ST/-AM/-DAM and the external PCB terminal.
3
(9.5 to 18 V DC)
External PCB terminal
NOTE
TROUBLE wiring not
required for VXI-ST.
Trouble
Power
(9.5 to 18 V DC)
Power
- SP TR
+
- SP TR
+
- SP TR
+
COM
COM
Alarm
COM
AL TP TP
AL TP TP
AL TP TP
to a control panel
to the VXI-CMOD
Tamper
VXI-ST/-AM/-DAM
Ribbon cable
[1]
(included)
70 mm
(Recommended)
[2]
NOTE
A separate power supply of 9.5 to 18 V DC is required
for VXI-ST/-AM/-DAM when VXI-CMOD is powered
by a source over 18 to 24 V DC.
Power
(over 18 to 24 V DC)
External PCB terminal
Power
(9.5 to 18 V DC)
to a control panel
to the VXI-CMOD
Tamper
Alarm
VXI-ST/-AM/-DAM
[3]
Wires
(not included)
1-1 BEFORE INSTALLATION
- Read this INSTALLATON & OPERATION MANUAL carefully prior to installation.
- After reading, store this manual carefully in an easily accessible place for reference.
- This manual uses the following indications for correct use of the product, harm to you or other people and damage to your
assets, which are described below. Be sure to understand the description before reading the rest of this manual.
Warning
Caution
1-2 CHOOSE LOCATION
Mounting height
Failure to follow the instructions provided with this indication and improper handling may cause death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause injury and/or property damage.
This symbol indicates prohibition.
Warning
Caution
Wi-Fi
Do not drop the product and/or avoid scratches on the lens as it may affect it s performance.
Be careful to avoid pinching the wires when assembling.
Read and follow the instructions provided with the VXI-ST/-AM/-DAM.
Adjust, set and check the VXI-ST/-AM/-DAM before starting the VXI-CMOD installation.
NOTE
It is hard to access to the inside of the VXI-ST/-AM/-DAM after mounting the VXI-CMOD.
Refer to the manual of VXI-ST/-AM/-DAM.
The radio environment and a
smart phone may affect the
Wi-Fi communication state.
1-3 LOCAL STORAGE
microSD card
For local storage use, a microSD card (not included)
is required.
Suitable microSD cards are as follows:
- FAT 32 format
- 32 GB max.
- Format in OPTEX Vision App
Power off the VXI-CMOD when installing microSD card.
To power down the VXI-CMOD disconnect the power or
remove the ribbon cable.
There is a 120 second boot up cycle.
0.8 to 1,2 m
PIR coverage
12 m max
Field of view
Horizontal:180°
Field of view
Vertical:100°
[4]
Wires
(not included)
[5]
[7]
‘
Open the
switch cover.
NOTE
If the PEU (Plug-in EOL) option is used on the VXI-ST/-AM/-DAM, remove it
from the terminal, then place it in the external PCB terminal of the VXI-CMOD.
VXI-ST/-AM/-DAM
The external antenna (option) for the VXI-CMOD can extend the reach of the Wi-Fi communication.
Follow this instruction only if external antenna is needed.
Set the antenna internal/external switch to EXT.
1 2 3
1.
Insert a
microSD card
2.
Set the ribbon cable
to the connector, and
attach the connector
cover.
External PCB terminal
3.
Return the switch
cover to the original
position.
Mount the bracket and set the main body.
[6]
[8]
Place the VXI-CMOD on the
VXI-ST/-AM/-DAM back box
temporarily.
NOTE
Accessing inside of the VXI-CMOD may be necessary in
the following process. Fix with the lock screw and attach
the CMOD cap at step 6.
Adjust the switch settings, if necessary.
IR-LED high/low switch
Recommended Current draw
Position
high
low
(default)
distance (max.)
(max.) at 12 V DC
12 m 1.0 A
6 m 400 mA
Connect cables to the VXI-CMOD.
1-5 PARTS IDENTIFICATIONS
[VXI-CMOD]
(without the CMOD cap)
CMOD cap
[Top view]
Lock screw hole
Power indicator
INSTALLATION
2
Disassemble the VXI-ST/-AM/-DAM while refering to
1
2 2-1 1 through 4 in the instllation instructions
of the VXI-ST/-AM/-DAM.
< Accessories >
External PCB
terminal
[Rear view]
(inside the body)
Camera mount
Ribbon
cable
Ribbon cable
connector
Waterproof
sponge
Mounting
screws
[Bottom view]
(without switch cover)
Reset switch
Switch cover
Make wiring knockout holes on the back box of the VXI-ST/-AM/-DAM.
2
Lock screw
QR code label
for Device ID
Antenna internal/
external switch
IR-LED high/low
switch
microSD card slot
APP INSTALLATION
3
Visit either the App store or Google play.
1
SETUP WIZARD
4
Start the OPTEX Vision application.
1
Main body
Bracket
Jump to step 4 , if the OPTEX Vision App has already been installed.
Jump to step 5 , if the Wi-Fi network has already been set.
Search for OPTEX Vision in the store.
2
3
OPTEX Vision
Requirement;
iPhone 5S with iOS 9.0 or later.
Android smartphone 5.X or later.
Tap “Add Device” to start “Setup Wizard” .
2
Download and install the
OPTEX Vision application.
- 1 -
When the “Setup Wizard” requires a Device ID input, use one of the following:
3
[1] Remove the CMOD cap and find the QR code which is located
on the top of VXI-CMOD.
[2] Read the QR code label included in the package of the VXI-CMOD.
[3] Direct input to the OPTEX Vision.
Follow the “Setup Wizard” to join your Wi-Fi network.
4
- Record the Wi-Fi network SSID and password.
Note them on [1] [2] below.
Wi-Fi network
[1] SSID;
[2] Password;
- Place the Device ID QR code label on [3].
It is included in the package of VXI-CMOD.
[3] Device ID;
NOTE
The default password is 123456, which will need to be appropriately
changed upon setup.
For iOS only
The following information is required to change the
Wi-Fi network in the “Setup Wizard”
Wi-Fi direct
SSID; HD- xxxxxx *
Password;
12345678
* “xxxxxx” contains ramdom numbers that are common to
the part of the Device ID.
IMPORTANT
Reset to the factory default
- If the "Setup Wizard" procedure fails for any reason (e.g input wrong Wi-Fi
password), reset the unit by holding the "RESET" button for 10 seconds.
- Stored event data are not deleted by the reset operation.
SPECIFICATIONS
7
7-1 DIMENSIONS
97
272
NOTE
For installers
After the installation is complete, check the full operation of the
product. Explain to all users the operation of the product and
make sure that it is fully understood. Provide all users with a
copy of this “INSTALLATION & OPERATIONAL MANUAL”
for future reference.
For users
Upon completion ensure you are provided with comprehensive
training on this product. Keep a copy of this “INSTALLATION &
OPERATION MANUAL” for future reference.
Users are responsible to position the camera such a way
that it does not look into someone else s property.
‘
[3] Place the
QR code
label here
OPERATION CHECK
5
1 2 3
Check the VXI-CMOD is
displayed on the Device
List.
ASSEMBLING
6
Remove the CMOD cap and mount the
1
VXI-CMOD on the camera mount.
Live ViewDevice List Recording
Confirm the Live View
through the VXI-CMOD.
Try to record the Live View
onto the microSD card.
Fix the VXI-CMOD with the lock
2
screw.
4
Sensor trigger recording
Front Door
Live Direct,N=1,Good,127.3KB/sVGA
SD
Test the total operation of the VXI-ST/-AM/-DAM and VXI-CMOD.
Confirm that the event is recorded by the trigger of the VXI-ST/-AM/-DAM.
3
Replace the CMOD cap.
71
7-2 SPECIFICATIONS
Model VXI-CMOD
Wireless connectivity
Data encryption
Security
Simultaneous viewers
Image sensor
Image resolution
Viewing angle
Minimum illumination
Night vision
Image compression
Image resolution
Frame rate
Recording period
Memory Storage
Power supply
Power consumption
Wake up time
Recording trigger
LED indicator
Microphone
IR Mode selector
Internal/ External
antenna selector
Location
Operating temperature
Operating humidity
IP rate
Weight
* Performance may be impacted when connecting to multiple smartphone simultaneously.
- Web service is subject to termination without prior notice.
- Specifications and designs are subject to change without prior notice.
106
Unit: mm
IEEE 802.11 b/g/n
AES 128-bit data encryption via proprietary P2P connection protocol
WEP/ WPA/ WPA2 (TKIP, 128-bit AES)
Max. 3 Concurrent viewers *
Full HD
1080P/720P/VGA (Selectable from App)
H: 180° V: 100°
0 lux. (with IR illumination)
IR LED with IR-Cut switcher
H.264 High profile
Full HD
15 FPS
30 sec. (inc. 2 s pre-record)
microSD card (32 GB max.)
Not included/ Only FAT 32 format compatible/ Formatable from OPTEX Vision App
9.5 to 24 V DC
IR low mode: 400 mA max./IR high mode: 1.0 A max. at 12 V DC
2 min.
Alarm, Tamper, Trouble (N.O./N.C.)
Power LED
1 input
high/low
Internal/ External selectable
External antenna [CMOD-ANT] is sold separately.
Outdoor/Indoor
-10℃ to +50
℃
90% max. (Non condensed)
IP 55
280 g
<< How to use the OPTEX Vision App >>
1
Responding to an alarm
Receive SMS from a control
panel or App notification
Alarm !
3
Search stored events
Start the OPTEX Vision application.
2
Check live view
4
Settings
Hereby, OPTEX declares that the radio equipment type VXI-CMOD is in compliance with
RED 2014/53/EU. The full text of the EU DoC is available at the following internet address;
EU DoC; www.optex.net
Optex VXI-CMOD shall be supplied by a SELV and LPS (or UL1310 class 2) power supply
or connected to a dedicated control unit with SELV and LPS output.
■ EU contact information
Manuf acturer:
OPTE X CO., LTD.
5- 8-12 Ogoto, O tsu,
Shiga, 520- 0101 JAPAN
Author ised r epre senta tive in E urope:
OPTE X (EUROP E) LTD./EMEA HE ADQ UARTERS
Unit 13, Cordwa llis Par k, Clive mont Road,
Maiden head Berkshire, SL6 7 BU U.K.
OPTEX INC./AMERICAS HQ (U.S.)
URL: www.optexamerica.com
OPTEX (EUROPE) LTD./EMEA HQ (U.K.)
URL: www.optex-europe.com
OPTEX TECHNOLOGIES B.V.
(The Netherlands)
URL: www.optex.eu
- 2 -
OPTEX CO., LTD. (JAPAN)
URL: www.optex.net
OPTEX SECURITY SAS (France)
URL: www.optex-europe.com/fr
OPTEX SECURITY Sp.z o.o. (Poland)
URL: www.optex.com.pl
OPTEX PINNACLE INDIA,
PVT., LTD. (India)
URL: www.optexpinnacle.com
NOTE
Default Admin Password is
It must be changed after the first access to “Settings”.
OPTEX KOREA CO.,LTD. (Korea)
URL: www.optexkorea.com
123456
.
OPTEX (DONGGUAN) CO.,LTD.
SHANGHAI OFFICE (China)
URL: www.optexchina.com
OPTEX (Thailand) CO., LTD. (Thailand)
URL: www.optex.co.th
Copyr
ight (C) 2018 OPTEX CO., LTD.
Loading...