Onyx BE150, BE180 User Manual

Bedside Terminal BE150/180
BE150/180
15.6”/18.5” Bedside Terminal
®
AtomTM N270 Processor
High Performance
Low Power Consumption
Wide LCD with Multimedia
BE150/180 Manual 1st Edition
June. 2010
Bedside Terminal BE150/180
Copyright Notice
This document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, nor for any infringements upon the rights of third parties, which may result from its use.
The material in this document is for product information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, ONYX Healthcare Inc., assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein
ONYX Healthcare Inc. reserves the right to make changes in the product design without notice to its users
Bedside Terminal BE150/180
Acknowledgments
Intel
®
and Atom™ N270 are registered trademarks of Intel ®
Corporation.
IBM, PC/AT, PS/2 are trademarks of International Business
Machines Corporation.
Microsoft
®
Windows is a registered trademark of Microsoft ®
Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc. SiS is a trademark of Silicon Integrated Systems Corp. VIA is a trademark of VIA Technology, Inc.
All other product names or trademarks are properties of their respective owners.
Bedside Terminal BE150/180
Packing List
Before you begin installing your Bedside Terminal, please make
sure that the following items have been shipped:
BE150 or BE180 Bedside Terminal. VESA Mount Screws Utility CD-ROM (Please insert the ONYX-BE150/180 CD-ROM
into external CD-ROM drive.) which Contains User’s Manual (in PDF format), Drivers and Utilities
If any of these items are missing or damaged, you should contact your distributor or sales representative immediately.
Headquarters Onyx Healthcare Inc. 2F, No.135, Lane 235, Pao-Chiao Rd., Hsin-Tien City, Taipei 231, Taiwan, R.O.C. TEL: +886-2-8919-2188 FAX: +886-2-8919-1699 E-mail: sales@onyx-healthcare.com http://www.onyx-healthcare.com
Bedside Terminal BE150/180
Worldwide Offices: Onyx Healthcare, USA Inc. 2663 Saturn street, Brea, CA 92821, USA Tel : +1-714-996-1800 Fax: +1-714-996-1811 Email: usasales@onyx-healthcare.com
Onyx Healthcare EUROPE
B.V. Ekkersrijt 4002, 5692 DA Son, The Net herlands Tel : +31-(0)499-462020 Fax: +31-(0)499-462010 Email: eusales@onyx-healthcare.com
Onyx Health
care Technology GmbH An der Trift65d 63303 Dreieich , Germany TEL: +49-(0)61033-7479-00 Fax: +49-(0)61033-7479-49 Email: eusales@onyx-healthcare.com
Bedside Terminal BE150/180
Onyx Healthcare (SU ZHOU) INC. Room 12, 2F, Building B, No.5 Xing Han Street, Suzhou Industrial Park, Jiang Su Province, China Tel: +86-512-67625700 Fax: +86-512-67617337 Email: cnsales@onyx-healthcare.com
Onyx Health
care Singapore PTE LTD 57 Genting Lane, #07-00, Singapore 349564 Tel: +65-67498749 Fax +65-67461595 Email: sgsales@onyx-healthcare.com
Bedside Terminal BE150/180
Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do not
use liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it
or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, only qualified service
personnel should open the equipment.
Bedside Terminal BE150/180
14.
If any of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to
work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.
15.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT.
16.
External equipment intended for connection to signal input/output or other connectors, shall comply with relevant UL / IEC standard (e.g. UL 1950 for IT equipment and UL 60601-1 / IEC 60601 series for systems – shall comply with the standard IEC 60601-1-1, Safety requirements for medical electrical systems. Equipment not complying with UL 60601-1 shall be kept outside the patient environment, as defined in the standard.
Caution:
It may cause the danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer.
Bedside Terminal BE150/180
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX1
3. Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
Bedside Terminal BE150/180
FCC
This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Bedside Terminal BE150/180
UL Module Description
BE150/180 AC modules are developed to suitable for the Classification Mark requirement
Bedside Terminal BE150/180
Safety Symbol Description
The following safety symbols are the further explanations for your reference.
Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1
Attention, consult ACCOMPANYING
DOCUMENTS.
Ground wire Protective Ground wire.
Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 60601-1, and CAN/CSA C22.2 NO. 601.1
Bedside Terminal BE150/180
Contents
Chapter 1 General Information
1.1 Introduction ....................................................................1-2
1.2 Feature ............................................................................1-3
1.3 Specification...................................................................1-4
1.4 Dimension.......................................................................1-9
Chapter 2 Hardware Installation
2.1 Safety Precautions.........................................................2-2
2.2 A Quick Tour of the BE150/180.....................................2-3
2.3 Removing the rear maintenance cover........................2-6
2.4 Hard Disk Drive (2.5” HDD) Installation.......................2-7
Chapter 3 Award BIOS Setup
3.1 System Test and Initialization.......................................3-2
3.2 Award BIOS Setup. ........................................................3-3
3.3 Standard CMOS Features..............................................3-5
3.4 Advanced BIOS Features..............................................3-5
3.5 Advanced Chipset Features..........................................3-5
3.6 Integrated Peripherals...................................................3-5
3.7 Power management Setup............................................3-5
3.8 PnP/PCI configuration...................................................3-6
3.9 PC Health Status............................................................3-6
3.10 Frequency/Voltage control..........................................3-6
3.11 Load Fail-Safe Defaults ...............................................3-6
Bedside Terminal BE150/180
3.12 Load Optimized Defaults.............................................3-7
3.13 Set Supervisor/User Password...................................3-7
3.14 Save & Exit Setup.........................................................3-8
3.15 Exit without saving ......................................................3-8
Chapter 4 Driver Installation
4.1 Installation ......................................................................4-2
4.2 Card Reader Driver Installation....................................4-3
4.3 Touch Screen Driver Installation..................................4-4
4.4 Smart Card Driver Installation ......................................4-4
4.5 RFID Driver Installation .................................................4-4
Appendix A Miscellanea
A.1 General Cleaning Tips..................................................A-2
A.2 Cleaning Tools..............................................................A-3
A.3 Scrap Computer Recycling ........................................A-5
Bedside Terminal BE150/180
Chapter 1 General Information 1-1
General
Information
Chapter
1
Loading...
+ 34 hidden pages