
ONYX-1531
15.6” FHD LCD with LED Backlight
Intel® Celeron J1900 Quad Core Processor
Slim Medical Panel PC
ONYX-1531 Manual 1st Ed
Mar., 2016

Copyright Notice
This document is copyrighted, 2016. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, nor for
any infringements upon the rights of third parties, which may result
from its use.
The material in this document is for product information only and
is subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, ONYX Healthcare Inc., assumes no liabilities resulting
from errors or omissions in this document, or from the use of the
information contained herein
ONYX Healthcare Inc. reserves the right to make changes in the
product design without notice to its users

Acknowledgments
Intel
®
CeleronTM is registered trademarks of Intel® Corporation.
Microsoft
®
Windows is a registered trademark of Microsoft®
Corporation.
All other product names or trademarks are properties of their
respective owners.

Packing List
Before you begin installing your Slim Medical Panel PC, please
make sure that the following items have been shipped:
ONYX-1531 Slim Medical Panel PC
Utility DVD-ROM, which contains Drivers and Utilities
Four VESA Screws(M:4mm x P:0.7mm x L:10mm)
Medical Power Adapter 60W/12VDC

If any of these items are missing or damaged, you should contact
your distributor or sales representative immediately.
Headquarters
Onyx Healthcare Inc.
2F., No.135, Ln. 235, Baoqiao Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
TEL: +886-2-8919-2188
FAX: +886-2-8919-1699
E-mail: sales@onyx-healthcare.com
http://www.onyx-healthcare.com
Worldwide Offices:
Onyx Healthcare, USA Inc.
324W. Blueridge Ave., Orange,, CA 92865, USA
Tel : +1-714-792-0774
Fax: +1-714-792-0481
Email: usasales@onyx-healthcare.com
Onyx Healthcare EUROPE B.V.
Primulalaan 42, 5582 GL Waalre, Netherlands
Tel : +31(0)499-745600
Email: eusales@onyx-healthcare.com

Onyx Healthcare (Shanghai) INC.
20F, unit D, GEM Building, No. 487 Tianlin Road,
Shanghai, China
Tel: +86-021-64956588
Fax: +86-021-64956889
Email: cnsales@onyx-healthcare.com

Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning.
Do not use liquid or spray detergents for cleaning. Use a damp
cloth.
4. For pluggable equipment, the power outlet must be installed
near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation.
Dropping it or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect
the equipment from overheating. DO NOT COVER THE
OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Warning: To avoid risk of electric shock, this equipment
must only be connected to a supply mains with protective
earth. (Avertissement: Pour éviter tout risque de choc
électrique, cet appareil doit être connecté à une
alimentation secteur avec une prise de terre)
10. Position the power cord so that people cannot step on it. Do
not place anything over the power cord.
11. All cautions and warnings on the equipment should be noted.

12. If the equipment is not used for a long time, disconnect it from
the power source to avoid damage by transient over-voltage.
13. Never pour any liquid into an opening. This could cause fire or
electrical shock.
14. Never open the equipment. For safety reasons, only
qualified service personnel should open the equipment.
15. Warning: Do not modify this equipment without
authorization of the manufacturer. (Avertissement: Ne pas
modifier cet équipement sans l'autorisation du fabricant)
16. If any of the following situations arises, get the equipment
checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it
to work according to the users manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
17. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY
DAMAGE THE EQUIPMENT.
18. External equipment intended for connection to signal
input/output or other connectors, shall comply with
relevant UL / IEC standard (e.g. UL 1950 for IT equipment
and ANSI/AAMI ES 60601-1: 2005 AND CAN/CSA-C22.2 No.
60601-1:08 / IEC 60601 series for systems – shall comply

with the standard IEC 60601-1-1, Safety requirements for
medical electrical systems. Equipment not complying
with UL 60601-1 shall be kept outside the patient
environment, as defined in the standard.
19. Unplug the power cord from the power adapter jack to
disconnect the device.
Caution:
It may cause the danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type
recommended by the manufacturer.

Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX0
3. Mode of operation: Continuous
4. Type of protection against electric shock: Class I equipment
5. No Applied Part, No AP/APG

FCC
This device complies with Part 18 FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference
received including interference that may
cause undesired operation.

ONYX-1531 module is developed to suitable
for the Classification Mark requirement

Safety Symbol Description
The following safety symbols are the further explanations for your
reference.
Medical equipment with respect to electric
shock, fire and mechanical hazards only in
accordance with ANSI/AAMI ES 60601-1:
2005 AND CAN/CSA-C22.2 No.
60601-1:08
Attention, consult ACCOMPANYING
DOCUMENTS.
Ground wire
Protective Ground wire.

Contents
Chapter 1 General Information……………..………………..P15
1.1 Introduction................................................................ P16
1.2 Feature ....................................................................... P17
1.3 Specification .............................................................. P18
1.4 Dimension .................................................................. P22
Chapter 2 Hardware Installation………………………….….P23
2.1 Safety Precautions .................................................... P24
2.2 Quick Tour of ONYX-1531........................................ ..P25
2.3 Mounting with VESA Mounting Holes………………… P28
2.4 Turn On and Boot up into Windows OS ………………P29
2.5 Turn off………………………………………………………P29
Chapter 3 Driver Installation………………….……………….P30
Appendix A Miscellanea………………………………………..P32
A.1 General Cleaning Tips............................................... P33
A.2 Cleaning Tools .......................................................... P34
A.3 Scrap Computer Recycling ..................................... P36

Chapter 1 General Information 1-1
1.1 Introduction
ONYX-1531 Slim Medical Panel PC is based on Intel® CeleronTM
J1900 Quad Core processor, which delivers a performance
improvement of more than 100 percent compared to systems
running traditional single-core processors. With four cores
computing engines, ONYX-1531 can simultaneously execute four
computing tasks. It accommodates one 2.5” SATA hard disk
drive/SSD and two DDRIII SODIMM up to 8GB.
The high brightness LCD, zero noise solution and integrated
multimedia functions make them the perfect platform upon which to
build comprehensive lifestyle computing applications.
ONYX-BE1531 offers a highly scalable bedside infotainment
solution to enhance patient experiences within the hospital.
Packaged with renowned software solution partners, ONYX-1531
bedside terminals provide patients with capabilities like
Entertainment on Demand, Online Access, VoIP Phone, Nurse
Notification, etc. ONYX-1531 is definitely your perfect choice.

Chapter 1 General Information 1-2
1.2 Feature
Intel
®
CeleronTM J1900 Quad Core Processor
Supports Dual Channel DDR3 SODIMM up to 8GB
Built-in RFID and Smart Card Security (Optional)
7 Smart Function Keys
Handset with remote control(Optional)
Magnetic Card Reader(optional)
Power over Ethernet Module for LAN1(optional)

Chapter 1 General Information 1-3
1.3 Specification
Hardware Specifications
Intel® CeleronTM J1900 Processor
Windows® 10 (32 bit & 64 bit )
Windows® 8.1 (32 bit & 64 bit )
Windows® 7 (32 bit & 64 bit )
Linux Fedora Core
2.5” Hard Disk Drive/Solid State Drive, mSATA Solid State
Drive
Magnetic Stripe Reader (Optional)
1D / 2D Barcode Scanner (Optional)
Power On/Off, Speaker Volume Up/Down, LCD Brightness
Up/Down, LCD On/Off, Touch Screen On/Off
1x RS-232 port (isolated, pass the dielectric test: 2122Vdc only)
4x USB 2.0 ports
2x Gigabit LAN (isolated, pass the dielectric test: 2122Vdc only)
Sound:
1 x Line-out
1 x Mic-in
Equipotential Terminal

Chapter 1 General Information 1-4
LCD Specifications
Note:
All ONYX LCD products are manufactured with High precision technology.
However, there are a small number of defective pixels in all LCD panels
that are not able to change color. This is a normal occurrence for all LCD
displays from all manufacturers and should not be noticeable or
objectionable under normal operation. All LCD panels are qualified for
industry standard conditions in the following: total 7 dead pixels on a
screen or if there are 3 within 1 inch square area of each other on the
display.

Chapter 1 General Information 1-5
Mechanical Specifications
Plastic bezel with resistive touch screen
VESA 75/100mm, Screw type:M4*8mm
3mm ABS + PC TYPE Plastic housing
Power Supply Specifications
100 ~ 240 Vac, 50/60 Hz, 1.6-0.7A
61320 Calculated Hours (7 years)

Chapter 1 General Information 1-6
Environmental Specifications
0˚C to 40˚C (32˚F ~104˚F)
30% to 75% RH, non-condensing
-20˚C to 60˚C (-4˚F ~140˚F)
10% to 90% RH, non-condensing
0.5G / 5 ~ 500Hz (Random) / operation
20G peak acceleration (11 msec. duration) /
operation
76cm (1 Corner, 3 Edge, 6 Surface)
CE / FCC Class B/ANSI AAMI ES60601-1/
EN 60601-1
Projective Capacitive / 5-wire Resistive

Chapter 1 General Information 1-7
1.4 Dimension
Dimensions: 397.8 x 265 x 39.3mm
VESA Mount: 75 x 75mm, 100 x 100mm

Chapter 2 Hardware Installation 2-1
Hardware
Installation

Chapter3 Award BIOS Setup 3-1
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis

Chapter3 Award BIOS Setup 3-2
2.2 Quick Tour of ONYX-1531
There are 7 control buttons in the front side of ONYX-1531. Please
refer to table 2.1 for the function of each button.
Picture 2.1: Front View of ONYX-1531 Series

Chapter3 Award BIOS Setup 3-3
Press 2 seconds to turn on the power
Hardware volume control - does not associate with Windows volume bar
Hardware volume control - does not associate with Windows volume bar
Enable/Disable Touch Screen
Table 2.1: Functions of Control Buttons

Chapter3 Award BIOS Setup 3-4
ONYX-1531 provides an optional remote control handset. Please
refer to table 2.2 for the function of each key.

Chapter3 Award BIOS Setup 3-5

Chapter3 Award BIOS Setup 3-6
2. Press 3
seconds
3. Press to
trigger barcode
Turn off
automatically
if no press
after 20
seconds
Table 2.2: Remote Control Functions

Chapter3 Award BIOS Setup 3-7
The sunken I/O section is at the bottom, as shown in Picture 2-2.
Picture 2.2: Bottom view of ONYX-1531 Series
Gigabit LAN x2 (isolated, pass the dielectric test: 2122Vdc only)
RS-232 (isolated, pass the dielectric test: 2122Vdc only)

Chapter3 Award BIOS Setup 3-8
When you turn ONYX-1531 around and look at its right side, the
smart card reader is on the right side as shown in Picture 2-3.
Picture 2.3:Right View of ONYX-1531 Series
2.3 Mounting with VESA Mounting Holes
ONYX-1531 can be mounted with 75mm x 75mm or 100mm x 100mm
VESA holes in the rear cover by wall-mount.
Picture 2.4: Back view of ONYX-1531

Chapter3 Award BIOS Setup 3-9
2.4 Turn on and Boot up into Windows OS
This section is for Windows operating system only. If you are
installing a different operating system, please contact your vendor
for installation details.
Your ONYX-1531 will begin loading Windows OS once you push
the power button to turn power on. After less than one minute,
Windows desktop screen will appear.
You can select the programs from the start menu in the left-down
corner of the desktop screen.
2.5 Turn off
Turning off ONYX-1531 properly is important for system reliability.
There are two ways to turn off the system.
1. On the start menu, click “shut down” and select “OK”
2. Push the power button and then the system will shut
down automatically

Chapter3 Driver Installation 3-1
Driver
Installation

Chapter 4 Drivers Installation 3-2
There are several installation ways depending on the driver
package under different Operating Systems.
Please follow the sequence below to install the drivers:
For Windows 7/8.1:
Step 1 – Chipset Driver
Step 2 – Graphics Driver
Step 3 – LAN Driver
Step 4 – Audio Driver
Step 5 – USB 3.0 Driver
Step 6 – Resistive Touch Screen Driver(only for ET series)
Step 7 – TPM Driver
Step 8 – Barcode Scanner Driver(optional)
For Windows 10:
Step 1 – Chipset Driver
Step 2 – Graphics Driver
Step 3 – Audio Driver
Step 4 – MBI Driver
Step 5 – TXE Driver
Step 6 – TPM Driver
Step 7 – Resistive Touch Screen Driver(only for ET series)
Step 8 – Barcode Scanner Driver(optional)

Appendix A Miscellanea A-1
Miscellanea

Appendix A Miscellanea A-2
A.1 General Cleaning Tips
You may need the following precautions before you begin to clean
the computer. When you clean any single part or component for the
computer, please read and understand the details below fully.
1. Be cautious of the tiny removable components when you
use a vacuum cleaner to absorb the dirt on the floor.
2. Turn the system off before you start to clean the component
or computer.
3. Never drop the components inside the computer or get
circuit board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals
when you use it for the sake of cleaning. Some individuals
may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the
computer.
Note: We strongly recommend that you should shut
down the system and remove the power cord before
cleaning ONYX-1531.

Appendix A Miscellanea A-3
A.2 Cleaning Tools
Although many companies have created products to help improve
the process of cleaning your computer and peripherals users can
also use household items to clean their computers and peripherals.
Below is a listing of items you may need or want to use while
cleaning your computer or computer peripherals.
Keep in mind that some components in your computer may only be
able to be cleaned using a product designed for cleaning that
component, if this is the case it will be mentioned in the cleaning
tips.
Cloth - A piece of cloth is the best tool to use when rubbing
up a component. Although paper towels or tissues can be
used on most hardware as well, we still recommend you to
rub it with a piece of cloth.
Water or rubbing alcohol – You may moisten a piece of
cloth a bit with some water or rubbing alcohol and rub it on
the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner - Absorb the dust, dirt, hair, cigarette
particles, and other particles out of a computer can be one
of the best methods of cleaning a computer. Over time
these items can restrict the airflow in a computer and cause
circuitry to corrode.

Appendix A Miscellanea A-4
Cotton swabs - Cotton swaps moistened with rubbing
alcohol or water are excellent tools for wiping hard to reach
areas in your keyboard, mouse, and other locations.
Foam swabs - Whenever possible it is better to use lint
free swabs such as foam swabs.
Please follow the steps below.
1. Close all application programs.
2. Close operating software.
3. Turn off power switch
4. Remove all device
5. Pull out power cable
Note:
We strongly recommended that you should shut down the
system before you start to clean any single components.

Appendix A Miscellanea A-5
A.3 Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform us as
soon as possible for the suitable solution. For the computers that
are no longer useful or work well, please contact with worldwide
distributors for recycling.
The worldwide distributors show on the following website:
http://www.onyx-healthcare.com.tw/Contact.php
Note:
Follow the national requirement to dispose unit