User
manual
T3
Contents
1 Important 2
2 Your Bluetooth speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
Turn on/o 5
Check the battery level 5
Charge the built-in battery 5
4 Use Bluetooth devices 7
Connect a Bluetooth-enabled device 7
Connect two Bluetooth devices
simultaneously 7
Play from Bluetooth device 8
Control your phone call 8
5 Other features 9
Charge your mobile devices 9
Enable/disable voice prompt 9
Use the detachable case 9
Reset the speaker 9
6 Product information 10
Specifications 10
7 Troubleshooting 11
General 11
8 Notice 12
1EN
1 Important
Warning
•
Never remove the casing of this speaker.
• Never lubricate any part of this speaker.
• Never place this speaker on other electrical
equipment.
• Keep this speaker away from direct sunlight, naked
flames or heat.
• Make sure that there is enough
free space around the speaker for
ventilation.
• Only use attachments or accessories
specified by the manufacturer.
• The battery shall not be exposed to
excessive heat such as sunshine, fire or
the like.
• The speaker shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on
the speaker (e.g. liquid filled objects,
lighted candles).
Note
The type plate is located on the bottom of the
•
product.
About operating temperatures and humidity
• Operate in a place where temperature
is between 0
o
C (32oF) and 40oC (104oF)
(up to 80% relative humidity)
• Battery life may be shorter in high or
low temperature conditions
2 EN
2 Your Bluetooth
speaker
Thank you for purchasing an Onkyo product.
Read this manual carefully before use. By
following these instructions, you can get
the best audio performance and the most
listening pleasure from your Onkyo product.
Introduction
With this speaker, you can
• enjoy audio from your Bluetooth-
enabled devices through Bluetooth;
• control the incoming phone call after
Bluetooth connection; and
• charge your mobile devices through the
USB socket.
What's in the box
Check and identify the contents of your
package:
Short User Manual
• Main unit
• USB cable
• Detachable case
• Printed materials
3EN
Overview of the speaker
a
g
h
i
b
c
d
a MIC
• Integrated microphone.
b
• Press to pause or resume play.
• Press twice to go to the previous
track or the beginning of the current
track.
• Press to answer an incoming call.
• During a call, press to end the
current call.
c -/+
• Adjust volume.
d
• Press and hold for two seconds to
enter pairing mode.
• Press twice to select the next track.
e
• Press and hold for two seconds to
turn the speaker on or o.
• Press to check the battery level
when the speaker is turned on.
e
f
f Bluetooth/power indicator
• Indicate the Bluetooth connection
status.
• Indicate the power status.
g OUT [PHONE] (5V
• Charge an external mobile device.
h IN (5V
• Charge the built-in battery.
i Battery indicator
• Indicate the battery status.
1A)
1A)
4 EN
3 Get started
.
Always follow the instructions in this
chapter in sequence.
Turn on/o
2 sec
0-20%21-69% 70-100%
• To turn the speaker on, press and hold
until you hear a tone.
» The power/Bluetooth indicator
flashes blue.
• To turn the speaker o, press and hold
again.
» The power/Bluetooth indicator
turns o.
Note
If there is no operation and audio output for 15
•
minutes, the speaker automatically turns o for
power-saving.
Check the battery level
The speaker is powered by a built-in
rechargeable battery. The dierent color
of the battery indicator indicates dierent
battery levels.
• Press .
» The battery indicator turns on for 5
seconds.
Color of Battery
Indicator
Green 70 - 100% charged
Yellow 21 - 69% charged
Red 0 - 20% charged
Battery level
Charge the built-in battery
If the battery level is low, recharge the builtin battery.
Note
The micro USB socket is for charging only.
•
• Rechargeable battery has a limited number of
charge cycles. Battery life and number of charge
cycles vary by use and settings.
• It takes approximately three hours to fully charge
the battery.
Note
Make sure that the speaker is turned on.
•
5EN
DC IN
• Connect the supplied USB cable
between
• the IN (5V
speaker, and
• a USB socket of a computer.
» The battery indicator turns solid
white.
» When the battery is fully charged,
the battery indicator turns o.
Tip
If you charge the battery and play music at the
•
same time, the volume will become relatively lower.
1A) socket on the
6 EN
4 Use Bluetooth
devices
With this speaker, you can listen to audio
from Bluetooth-enabled devices and control
the incoming call through Bluetooth.
Connect a Bluetoothenabled device
Note
Make sure that your Bluetooth device is compatible
•
with this speaker.
• Before pairing a device with this speaker, read its
user manual for Bluetooth compatibility.
• Make sure that Bluetooth function is enabled on
your device, and your device is set as visible to all
other Bluetooth devices.
• Any obstacle between this speaker and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that
may cause interference.
• The operational range between this speaker and
a Bluetooth device is approximately 10 meters (30
feet).
1 Make sure that the speaker is in pairing
mode.
» The power/Bluetooth indicator
flashes blue quickly.
» If the power/Bluetooth indicator
flashes blue slowly, press and hold
for two seconds to enter pairing
mode.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth
devices (refer to the user manual of the
device).
3 When [Onkyo T3] is displayed on your
device, select it to start pairing and
connection. If necessary, enter the
default password “0000”.
» After successful pairing and
connection, the speaker beeps, and
the power/Bluetooth indicator turns
solid blue.
To disconnect the Bluetooth-enabled
device:
• Press and hold
seconds;
• Disable Bluetooth on your device; or
• Move the device beyond the
communication range.
» The power/Bluetooth indicator
flashes blue.
To reconnect the Bluetooth-enabled device:
• Next time you turn on the speaker,
the speaker tries to reconnect the last
connected device automatically;
• If not, manually select "Onkyo T3"
on your Bluetooth device to start
connection.
on the speaker for two
Connect two Bluetooth
devices simultaneously
The speaker can connect to two Bluetooth
devices at the same time.
1 Connect one Bluetooth device (see the
above section "Connect a Bluetoothenabled device").
2 Press and hold for two seconds to
enter pairing mode.
» The LED indicator flashes blue
quickly, and the first device is
disconnected.
3 Connect the second Bluetooth device.
7EN
4 Select [Onkyo T3] displayed on
your first Bluetooth device to start
reconnection.
» The two Bluetooth devices are
connected to the speaker at the
same time.
» If you press and hold
two seconds, the two devices are
disconnected, and the speaker is
ready to pair with a new device.
again for
Control your phone call
After Bluetooth connection, you can control
an incoming call with this speaker.
Button Function
Press to answer an incoming call.
During a call, press to end the
current phone call.
Tip
For a paired Bluetooth device, this speaker tries to
•
reconnect with it once it is detected. If it fails, you
just need to select [Onkyo T3] on your device to
start reconnection.
Play from Bluetooth device
Note
If there is an incoming call on the connected mobile
•
phone, music play pauses.
After successful Bluetooth connection, play
audio on any connected Bluetooth device.
» Audio streams from your Bluetooth
device to the speaker.
• To go to the previous track or the
beginning of the current track
(depending on the setting of your
mobile devices), press
• To go to the next track, press
• To pause or resume play, press
• To increase or decrease volume, press
+/-.
twice.
twice.
.
Note
You can talk through the microphone of the
•
speaker.
• Music play pauses when there is an incoming call,
and resumes when your phone call ends.
8 EN
5 Other features
Enable/disable voice
prompt
Charge your mobile devices
You can charge your mobile devices through
the OUT [PHONE] socket.
Note
The USB socket is for charging only.
•
• Do not connect the IN socket and the OUT [PHONE]
socket with the same cable.
• Stop music play while charging your mobile
devices.
1 Turn on the speaker.
2 Connect to your mobile device with the
USB cable.
» Once the device is recognized, the
charging starts.
» During charging, the speaker turns
o automatically.
Press and hold for two seconds to
enable or disable the voice prompt.
» When the voice prompt is enabled, the
speaker will speak in English.
» When the voice prompt is disabled, the
speaker will change to the tone mode.
Use the detachable case
A detachable case is provided to place
the speaker on a flat surface. Follow the
illustration to install the case.
Reset the speaker
If the system works abnormally, reset the
speaker to factory default settings.
1 Turn on the speaker.
2 Press and together for five
seconds.
» All settings are reset to factory
default.
9EN
6 Product
information
Note
Product information is subject to change without
•
prior notice.
Specifications
Amplifier
Total Output Power 2 x 4 W
Frequency Response 100 Hz - 20 kHz
Total Harmonic
Distortion
Bluetooth
Bluetooth Version V4.0
Bluetooth Frequency
Band
Bluetooth distance 10 m (Free space)
< 1%
2.402 - 2.480 GHz
Dimensions
- Main Unit
(W x H x D)
Weight
- Main Unit 0.25 kg
144 x 71 x 23 mm
Speakers
Speaker Impedance 8 ohm
Speaker Driver 2 x 1.5’’ full range
Sensitivity ≥ 79.0 dB/1W/1m
General information
Operation Power
Consumption
Eco Standby Power
Consumption
Built-in Battery Polymer lithium
10 EN
8 W
0.1 W
ion battery
(800mAh/3.7V X 3)
7 Troubleshooting
Warning
•
Never remove the casing of this device.
To keep the warranty valid, never try to
repair the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, contact Onkyo service center.
When you contact Onkyo, make sure that the
device is nearby and the model number and
serial number are available.
General
No power
• Recharge the built-in battery.
No sound
• Adjust volume on the speaker or the
Bluetooth-connected device.
• Make sure that your Bluetooth device is
within the eective operational range.
No response from the speaker
• Restart the speaker.
Cannot charge mobile devices
• Make sure that the built-in battery still
has power.
• Connect to the mobile phone correctly.
Cannot connect with the device.
• The Bluetooth function of the device is
not enabled. Refer to the user manual
of the device for how to enable the
function.
• The speaker is not in pairing mode.
Press and hold
the power/Bluetooth indicator flashes
blue quickly, and then try again.
The paired device connects and
disconnects constantly.
• The Bluetooth reception is poor. Move
the device closer to this product or
remove any obstacle between them.
• For some devices, Bluetooth connection
may be deactivated automatically as
a power-saving feature. This does
not indicate any malfunction of this
speaker.
for two seconds until
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
• The Bluetooth reception is poor. Move
the device closer to this speaker or
remove any obstacle between them.
11EN
8 Notice
Any changes or modifications made to this
device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.
Hereby, Gibson Innovations declares that
this product is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC. You can
find the Declaration of Conformity on www.
onkyo-speakers.com.
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive 2013/56/EU
which cannot be disposed of with normal
household waste.We strongly advise you to
take your product to an ocial collection
point or an Onkyo service centre to have
a professional remove the rechargeable
battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
negative consequences for the environment
and human health.
Caution
Removal of the built-in battery invalidates the
•
warranty and may destroy the product.
Always bring your product to a professional
to remove the built-in battery.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassembled
by a specialized company. Please observe
the local regulations regarding the disposal
of packaging materials, exhausted batteries
and old equipment.
The Bluetooth
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by
Gibson Innovations Limited is under license.
Onkyo
Corporation. Other trademarks and trade
names are those of their respective owners
®
word mark and logos are
®
is a registered trade mark of Onkyo
12 EN
13
www.onkyo-speakers.com
Specifications are subject to change without notice.
2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the
responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd.
is the warrantor in relation to this product.
Onkyo® is a registered trade mark of Onkyo Corporation. Other
trademarks and trade names are those of their respective owners.
OKAT3_00_UM_V3.0
Loading...