Onkyo PR-SC886 User Manual

Page 1
AV C o n t r o l l er
PR-SC886
Contents
Introduction ...................................2
Connection ..................................21
First Time Setup ..........................46
Basic Operation...........................64
Using the Listening Modes ........75
Advanced Setup ..........................86
Instruction Manual
Thank you for purchasing an Onkyo AV Controller. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Controller. Please retain this manual for future reference.
Zone 2 and Zone 3.....................115
Controlling Other Components
Others.........................................127
..122
E
n
Page 2
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radia­tors, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are pro­vided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta­cles, and the point where they exit from the appara­tus.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table spec­ified by the manufacturer, or sold with the apparatus. When a cart is used, use cau­tion when moving the cart/ apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
PORTABLE CART WARNING
S3125A
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons. The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous volt­age points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.
17. Batteries Always consider the environmental issues and fol­low local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is ade­quate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue­like gap for warm air to escape.
2
Page 3
Precautions
1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal with­out the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user­serviceable. If you cannot turn on the unit, contact your Onkyo dealer.
3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild deter­gent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thin­ners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel let­tering.
4. Power WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SEC­TION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.
For North American model
Pressing the [ON/STANDBY] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.
5. Preventing Hearing Loss Caution
Excessive sound pressure from earphones and head­phones can cause hearing loss.
6. Batteries and Heat Exposure War nin g
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.
7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.
8. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi­nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so be sure to use it occasionally.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer­ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor­dance with the instructions, may cause harmful interfer­ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter­ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dif­ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni­cian for help.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modèle canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la fiche est polarisée:
AT TE NT IO N : POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRE­SPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
3
Page 4
Precautions—Continued
For British models
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cord’s plug is not suitable for your socket outlets, cut it off and fit a suitable plug. Fit a suitable fuse in the plug.
For European Models
Declaration of Conformity
We,
ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY
declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
4
Page 5
Contents
Features ............................................................6
Supplied Accessories ......................................7
Multiroom Capability ........................................8
Front & Rear Panels .........................................9
Front Panel ...................................................................9
Display ....................................................................... 11
Rear Panel .................................................................. 12
Remote Controller ..........................................15
Installing the Batteries ...............................................15
Aiming the Remote Controller ..................................15
About the Remote Controller Modes .........................16
RECEIVER/TAPE Mode ..........................................16
DVD Mode ................................................................ 18
CD/MD/CDR Modes .................................................19
DOCK Mode ..............................................................20
About Home Theater ......................................21
Enjoying Home Theater .............................................21
Connecting the AV Controller .......................22
Connecting Your Speakers ........................................ 22
Connecting a Power Amplifier with RCA Inputs ......23
Connecting a Power Amplifier with XLR Inputs ......24
Bi-amping the Front Speakers ...................................25
Connecting Antenna ..................................................26
About AV Connections ..............................................28
Connecting Both Audio & Video ..............................29
Which Connections Should I Use? ............................29
Connecting a TV or Projector .................................... 31
Connecting a DVD player .......................................... 32
Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Connecting a Satellite, Cable, Terrestrial Set-top box, or
Other Video Source ................................................. 36
Connecting Components with HDMI ........................37
Connecting a Game Console ...................................... 39
Connecting a Camcorder or Other Device ................. 40
Connecting a CD Player or Turntable ........................41
Connecting a Cassette, CDR, MiniDisc, or DAT
Recorder ..................................................................42
Connecting a Balanced Audio Source .......................42
Connecting an RI Dock .............................................. 43
Connecting the Power Cords of Other Components
(North American model only) .................................43
Connecting Onkyo u Components .........................44
Connecting the Power Cord .......................................44
......34
....35
Turning On the AV Controller ........................45
Turning On and Standby ............................................45
First Time Setup .............................................46
Monitor Setup ............................................................46
Selecting the Language used for the onscreen setup
menus ...................................................................... 47
Using the Onscreen Setup Menus .............................. 48
Monitor Out Setup .....................................................49
Video Input Setup ......................................................50
Digital Audio Input Setup ..........................................53
Analog Audio Input Setup .........................................54
Speaker Settings .........................................................55
TV Format Setup (not North American models) ....... 56
AM Frequency Step Setup (on some models) ...........57
Changing the Input Display .......................................57
Automatic Speaker Setup (Audyssey MultEQ® XT)
....58
Basic Operations ............................................64
Selecting the Input Source ......................................... 64
Setting the Display Brightness .................................. 65
Adjusting Speaker Levels .......................................... 65
Muting the AV Controller ......................................... 65
Using the Sleep Timer ............................................... 66
Using Headphones .....................................................66
Adjusting the Bass & Treble ..................................... 66
Displaying Source Information ................................. 66
Listening to the Radio ....................................67
Listening to AM/FM Stations .................................... 67
Presetting AM/FM Stations ....................................... 69
Listening to HD Radio™ Stations
(North American model only) ................................. 70
Using RDS ................................................................. 72
Recording ........................................................74
Recording the Input Source ....................................... 74
Recording from Different AV Sources ...................... 74
Using the Listening Modes ............................75
Selecting the Listening Modes .................................. 75
Listening Modes Available for Each Source Format
About the Listening Modes ....................................... 82
.... 76
Advanced Setup ..............................................86
Menu Map ................................................................. 86
Monitor Out Setup ..................................................... 87
Speaker Setup ............................................................ 89
Audio Adjust ............................................................. 98
Using the Music Optimizer ..................................... 101
Using the Re-EQ Function ...................................... 101
Using the Late Night Function ................................ 102
Source Setup ............................................................ 102
Listening Mode Presets ........................................... 107
Miscellaneous Setup ................................................ 108
Hardware Setup ....................................................... 110
Network Settings ..................................................... 112
Lock Setup ............................................................... 113
Selecting Audio Inputs ............................................ 114
Specifying the Digital Signal Format ...................... 114
Zone 2 and Zone 3 ........................................115
Connecting Zone 2 .................................................. 115
Connecting Zone 3 .................................................. 116
Zone 2/Zone 3 Out Settings ..................................... 117
Using Zone 2 and Zone 3 ........................................ 117
Using the 12V Triggers ........................................... 120
Using the Remote Controller in Zone 2/3 and Multiroom
Control Kits ........................................................... 121
Controlling Other Components ...................122
Entering Remote Control Codes .............................. 122
Resetting the Remote Controller ............................. 123
Learning Commands ............................................... 125
Using Macros ........................................................... 126
Troubleshooting ...........................................127
Specifications ...............................................132
5
Page 6

Features

Processing
• HDMI Audio and Video Processing (Deep Color, x.v.Color, Lip Sync, DTS DTS-HD High Resolusion Audio, Dolby TrueHD*2, Dolby Digital Plus, SA-CD and Multi-CH PCM)
• THX Ultra2 Plus
*3
• HQV-Reon-VX Video Processing with 1080p Video Upscaling of All Video Sources via HDMI
• Component Video Upconversion
• Burr-Brown 192 kHz/24-bit D/A Converters
• Three-TI (Aureus) 32-Bit DSP Chips
• Neural Surround
*4
• Theater-Dimensional*5 virtual surround sound
•DSD Direct
*6
•Re-EQ
function
*1
-HD Master Audio,
Certified
, THX-Neural
Connections
• Balanced XLR stereo input
• Balanced XLR 7.1-channel preouts, with front biamp­ing capability
*7
• 4 HDMI
Inputs and 2 Outputs
• Onkyo for System Control
• 6 Digital Inputs (3 Optical / 3 Coaxial), 1 Output (Optical)
• 6 S-Video Inputs / 2 Outputs
• Component Video Switching (3 Inputs/2 Outputs)
• Zone 2 and Zone 3 Pre Out, and subwoofer preouts
• IR Input/Output and 12 V Trigger
• RS232 Port for Interface Control
Miscellaneous
• SIRIUS Ready*8 / XM Ready round (North American models only)
*10
• HD Radio
reception (North American models
only)
• 40 SIRIUS/XM/AM/FM Presets (North American models)
• 40 AM/FM Presets (European and Asian models)
*11
• Music Optimizer Audyssey
MultEQ®XT
for Compressed Music Files
Problems
• Audyssey Dynamic EQ
• Audyssey Dynamic Volume
• Indepedent Crossover Adjustment (40/45/50/55/60/70/80/90/100/110/120/130/150/200 Hz)
• ISF (Imaging Science Foundation) Video Calibration
• Newly Designed GUI for System Set-up
• Compatible with RI Dock for iPod
• Preprogrammed u-Compatible Remote with 3 Mac­ros and Mode-Key LEDs
*9
with XMHD Sur-
*12
to Correct Room Acoustic
*12
Loudness Correction
*12
*1
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc. ©1996-2007 DTS, Inc. All Rights Reserved.
*2
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.
*3
THX and Ultra2 Plus are trademarks of THX Ltd. THX may be registered in some jurisdictions. All rights reserved. Surround EX is a trademark of Dolby Laboratories. Used with permis­sion.
*4
Neural Surround is a trademark owned by Neural Audio Cor­poration, THX is a trademark of THX Ltd., which may be reg­istered in some jurisdictions. All rights reserved.
*5
Theater-Dimensional is a trademark of Onkyo Corporation.
*6 Re-Equalization and the “Re-EQ” logo are trademarks of THX
Ltd.
*7
HDMI, the HDMI logo and High Definition Multimedia Inter­face are trademarks or registered trademarks of HDMI Licens­ing, LLC.
*8
©2005 SIRIUS Satellite Radio Inc. “SIRIUS”, SiriusConnect, the SIRIUS dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. Available only in the contiguous United States (excluding Alaska and Hawaii) and Canada.
*9
®
XM Ready XM Satellite Radio Inc. All rights reserved.
*10
HD Radio™ Technology Manufactured Under License From iBiquity Digital Corp. U.S. and Foreign Patents. HD Radio™ and the HD Radio logo are proprietary trademarks of iBiquity Digital Corp.
*11 Music Optimizer™ is a trademark of Onkyo Corporation.
*12
Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey MultEQ®XT, Audyssey Dynamic Volume
are trademark of Audyssey Laboratories.
is a trademark of XM Satellite Radio Inc. ©2005
, and Audyssey Dynamic EQ™
6
Page 7
Features—Continued

Supplied Accessories

THX Ultra2 Plus
Before any home theater component can be THX Ultra2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a prod­uct feature the THX Ultra2 Plus logo, which is your guarantee that the Home Theater products you pur­chase will give you superb performance for many years to come. THX Ultra2 Plus requirements define hundreds of parameters, including power amplifier performance, and pre-amplifier performance and operation for both digital and analog domains. THX Ultra2 Plus receivers also feature proprietary THX technologies (e.g., THX Mode) which accurately translate movie soundtracks for home theater play­back.
* “Xantech” is a registered trademark of Xantech Corporation. * “Niles” is a registered trademark of Niles Audio Corporation. * Apple and iPod are trademarks of Apple Inc., registered in the
U.S. and other countries.
* “x.v.Color” is a trademark of Sony Corporation.
This product incorporates copyright protection technol­ogy that is protected by U.S. patents and other intellec­tual property rights. Use of this copyright protection technology must be authorized by Macrovision Corpora­tion, and is intended for home and other limited con­sumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is pro­hibited.
Make sure you have the following accessories:
Remote controller and three batteries (AA/R6)
Speaker setup microphone
Indoor FM antenna
AM loop antenna
Power cord
(Power cord varies from country to country.)
* In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the same regardless of color.
7
Page 8

Multiroom Capability

You can use three speaker systems with this AV controller—a surround-sound speaker system (up to 7.1 channels) for enjoying DVD movies in your main room, Zone 2: a stereo speaker system in a second room, Zone 3: a stereo speaker system in a third room. And, you can select a different audio source for each room.
Main Room: Enjoy up to 7.1-channel surround-sound playback (see page 21–25). You can enjoy the various listening modes, such as Dolby, DTS, and THX (see pages 75–85).
Zone 2: Enjoy 2-channel stereo playback and video playback in a second room (see page 115).
*The listening modes cannot be used with Zone 2 and Zone 3. *External power amplifier required.
Zone 3: Enjoy 2-channel stereo playback in a third room (see page 116).
*The listening modes cannot be used with Zone 2 and Zone 3. *External power amplifier required.
Main Room
Surround back left and right
Front Speakers
speakers
Subwoofer
Zone 2 Room
Left and right stereo speakers
Center speaker
Surround left and right speakers
Zone 3 Room
Left and right stereo speakers
8
Page 9

Front & Rear Panels

Front Panel

5 61 2
43
87
blbk9
The actual front panel has various logos printed on it. They are not shown here for clarity.
The page numbers in parentheses show where you can find the main explanation for each item.
a ON/STANDBY button (45)
Sets the AV controller to On or Standby.
b STANDBY indicator (45)
Lights up when the AV controller is on Standby and flashes while a signal is being received from the remote controller.
c ZONE 2 indicator (118)
This indicator lights up when Zone 2 is selected.
d ZONE 3 indicator (118)
This indicator lights up when Zone 3 is selected.
e Remote-control sensor (15)
Receives control signals from the remote controller.
f Display
See “Display” on page 11.
g DISPLAY button (66)
Displays various information about the currently selected input source.
h MASTER VOLUME control (64) and indicator
Sets the volume of the AV controller to –81.5 dB through +18.0 dB (relative display).
The volume level can also be displayed as an abso­lute value. See “Volume Setup” on page 108.
dB,
Front flap
i PURE AUDIO button and indicator (75)
Selects the Pure Audio listening mode. The indica­tor lights up when this mode is selected. Pressing this button again selects the previous listening mode.
j AUDIO SEL button (114)
Selects the audio input: analog, digital, HDMI, or multichannel.
k Input selector buttons (64)
Select the following input sources: DVD, VCR/DVR, CBL/SAT, GAME/TV, AUX 1, AUX 2, TAPE, TUNER, CD, PHONO.
Push here to open the flap
9
Page 10
Front & Rear Panels—Continued
North American model
bm bn bo bp bq br bs bt ck cl cm co cp
ctcr cs
Other models
btdk
The page numbers in parentheses show where you can find the main explanation for each item.
l PHONES jack (66)
This 1/4-inch phone jack is for connecting a stan­dard pair of stereo headphones for private listening.
m ZONE 2, ZONE 3, and OFF buttons (118)
The ZONE 2 button is used when setting Zone 2. The ZONE 3 button is used when setting Zone 3. The OFF button is used to turn off Zone 2 or Zone 3.
n LEVEL button (119)
Used when adjusting the volume level of Zone 2 or Zone 3.
o TONE button (119)
Used to adjust the tone (bass and treble).
p HDMI OUT button (46)
Used to set the “Monitor Out” setting.
q STEREO button (75)
Selects the Stereo listening mode.
r THX button (75)
Selects the THX listening modes.
s DIMMER (RT/PTY/TP) button (65, 73)
This button is used to adjust the display brightness. Other models, this is the [RT/PTY/TP] button, and
it’s for RDS (Radio Data System). See “Using RDS” on page 72.
t MEMORY button (69)
Used when storing or deleting radio presets.
u TUNING MODE button (67)
Selects the Auto or Manual tuning mode.
v SETUP button
This button is used to access the onscreen setup menus that appear on the connected TV.
w TUNING, PRESET, Arrow, and ENTER
buttons
When the AM or FM input source is selected, the TUNING [q]/[w] buttons are used to tune the tuner, and the PRESET [e]/[r] buttons are used to select
radio presets (see page 69). When the onscreen setup menus are used, they work
as arrow buttons and are used to select and set items. The [ENTER] button is also used with the onscreen setup menus.
x RETURN button
Selects the previously displayed onscreen setup menu.
y SETUP MIC (58)
The included speaker setup microphone is con­nected here for automatic speaker setup.
z AUX 2 INPUT (40, 74)
Used to connect a camcorder, game console, and so on. There are input jacks for optical digital audio, S-Video, composite video, and analog audio.
cr Up [r] and Down [e] buttons (99, 119)
Used to adjust the tone, and the volume and balance of Zone 2 and Zone 3.
cs DIGITAL INPUT button (58)
Used to assign digital inputs to input selectors.
cqcn
10
Page 11
Front & Rear Panels—Continued
ct LISTENING MODE [e]/[r] buttons (75)
Select the Onkyo original listening modes.

Display

1
2
65
For detailed information, see the pages in parentheses.
a Speaker/channel indicators (82)
Indicate the speaker configuration and channels used by the current input source.
: A box is displayed for each speaker that’s set in the Speaker Configuration. No box appears for speakers that are set to No or None.
The following abbreviations indicate which audio channels are included in the current input signal.
FL: Front left C: Center FR: Front right SL: Surround left LFE: Subwoofer (Low Frequency Effects) SR: Surround right SBL: Surround back left SB: Surround back SBR: Surround back right
b Listening mode and format indicators (75)
Show the selected listening mode and audio input signal format.
c Tuning indicators
HD (North American model only) (70)
Lights up if the current AM or FM station supports HD Radio technology.
SPS (North American model only) (71)
Lights up when tuned to a HD Radio station that’s transmitting secondary multicast channels.
RDS (72):
Lights up when tuned to a radio station that supports RDS (Radio Data System).
dk POWER switch (45)
American models do not have this switch. This is the main power switch. When set to OFF,
the AV controller is completely shutdown. It must be set to ON to set the AV controller to On or Standby.
3
987
AUTO (67):
Lights up when Auto Tuning mode is selected for AM or FM radio. Goes off when Manual Tuning mode is selected.
TUNED (67):
Lights up when tuned to a radio station.
FM STEREO (67):
Lights up when tuned to a stereo FM station.
d SLEEP indicator (66)
Lights up when the Sleep function has been set.
Audyssey indicator (58)
Flashes during automatic speaker setup. Lights up when the “Equalizer Settings” is set to “Audyssey”.
e Headphone indicator (66)
Lights up when a pair of headphones are plugged into the PHONES jack.
f Message area
Displays various information.
g Audio input indicators (70, 114)
Indicate the type of audio input that’s selected as the audio source: HDMI, ANALOG, or DIGITAL.
While a digital HD Radio transmission is being received, the DIGITAL indicator lights up. While an analog HD Radio transmission is being received, the ANALOG indicator lights up.
h Volume level (64)
Displays the volume level.
i MUTING indicator (65)
Flashes while the AV controller is muted.
4
bk
11
Page 12
Front & Rear Panels—Continued

Rear Panel

North American model
21
378bmbo
ck cmcl
bt
Other models
654bkbrbqbp
9
co cp cq cs ct dm dndk dlcrcn
bl bn bq
bs
do
a u REMOTE CONTROL
This u (Remote Interactive) jack can be con­nected to the u jack on another u-capable
Onkyo component for remote and system control. To use u, you must make an analog audio connec-
tion (RCA) between the AV controller and the other component, even if they are connected digitally.
12
b RS232
This port is for connecting the AV controller to home automation equipment and external control­lers.
c PHONO IN
This audio input is for connecting a turntable.
Page 13
Front & Rear Panels—Continued
d COMPONENT VIDEO IN 1, 2, and 3
These RCA component video inputs are for con­necting components with a component video out­put, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Component Video Setup” on page 52.
e COMPONENT VIDEO MONITOR OUT 1
This RCA component video output is for connect­ing a TV or projector with a component video input.
f COMPONENT VIDEO MONITOR OUT
2/ZONE 2 OUT
This RCA component video output is for connect­ing a TV or projector with a component video input located in your main listening room or Zone 2.
g HDMI IN 1–4, OUT MAIN, and OUT SUB
HDMI (High Definition Multimedia Interface) con­nections carry digital audio and digital video.
The HDMI inputs are for connecting components with an HDMI output, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Video Input Setup” on page 50.
The HDMI outputs are for connecting a TV or pro­jector with an HDMI input.
h SIRIUS antenna (on North American model)
This jack is for connecting a SIRIUS digital antenna, sold separately (see the separate SIRIUS instructions).
i XM antenna (on North American model)
This jack is for connecting an XM Mini-Tuner and Home Dock, sold separately (see the separate XM instructions).
j MONITOR OUT
The S-Video or composite video jack should be connected to a video input on your TV or projector.
k AM ANTENNA (not North American model)
These push terminals are for connecting an AM antenna.
l ZONE 2 OUT
This composite video output can be connected to a video input on a TV in Zone 2.
m FM ANTENNA (not North American model)
This jack is for connecting an FM antenna.
n IR IN A/B and OUT
A commercially available IR receiver can be con­nected to the IR IN A or B jack, allowing you to control the AV controller while you’re in Zone 2, or control it when it’s out of sight, for example, installed in a cabinet.
A commercially available IR emitter can be con­nected to the IR OUT jack to pass IR (infrared) remote control signals through to other components.
o 12V TRIGGER OUT (A/B/C)
These outputs can be connected to the 12-volt trig­ger inputs on other components.
p ETHERNET
This port is for connecting the AV controller to home automation equipment and external control­lers. Use only shielded Ethernet cables.
q AM and FM ANTENNA (HD Radio reception)
(on North American model)
The AM push terminals are for connecting an AM antenna. The FM jack is for connecting an FM antenna.
r AC INLET
The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet.
s DIGITAL COAXIAL IN 1, 2, and 3
These coaxial digital audio inputs are for connect­ing components with a coaxial digital audio output, such as a CD player or DVD player. They’re assign­able, which means you can assign each one to an input selector to suit your setup. See “Digital Audio Input Setup” on page 53.
t DIGITAL OPTICAL IN 1, 2, and OUT
These optical digital audio inputs are for connecting components with an optical digital audio output, such as a CD player or DVD player. They’re assign­able, which means you can assign each one to an input selector to suit your setup. See “Digital Audio Input Setup” on page 53.
The optical digital audio output is for connecting a digital recorder with an optical digital input, such as a CD recorder.
u GND screw
This screw is for connecting a turntable’s ground wire.
v BALANCE L/R INPUT
This balanced XLR input is for connecting a com­ponent with a stereo balanced XLR output. For a mono source, connect to the BALANCE L XLR.
w CD IN
This analog audio input is for connecting a CD player’s analog audio output.
13
Page 14
Front & Rear Panels—Continued
x TAPE IN/OUT
These analog audio input and output jacks are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc.
y AUX 1 IN
A VCR for playback only or other video source can be connected here. There’s S-Video and composite video input jacks for connecting the video signal.
z GAME/TV IN
A game console or TV output can be connected here. There’s S-Video and composite video input jacks for connecting the video signal.
cr CBL/SAT IN
A cable or satellite receiver can be connected here. There’s S-Video and composite video input jacks for connecting the video signal.
cs VCR/DVR IN/OUT
A video component, such as a VCR or DVR, can be connected here for recording and playback. There’s S-Video and composite video input and output jacks for connecting the video signal.
ct DVD IN
This input is for connecting a DVD player. There’s S-Video and composite video input jacks for con­necting the video signal.
dk PRE OUT: FRONT L/R, CENTER,
SUBWOOFER, SURR L/R, and SURR BACK L/R
This 5.1/7.1 multichannel analog audio output can be connected to the analog audio input on a multi­channel power amplifier for when you want to use the AV controller solely as a preamplifier. The SUBWOOFER jack is for connecting a powered subwoofer.
dl MULTI CH input: FRONT L/R, CENTER,
SUBWOOFER, SURR L/R, and SURR BACK L/R
This analog multichannel input is for connecting a component with a 5.1/7.1-channel analog audio out­put, such as a DVD player, DVD-Audio or SACD-capable player, or an MPEG decoder.
dm PRE OUT: FRONT L/R, CENTER,
SUBWOOFER, SURR L/R, and SURR BACK L/R
This 5.1/7.1 multichannel analog audio output can be connected to the analog audio input on a multi­channel power amplifier. The SUBWOOFER jack is for connecting a powered subwoofer.
dn PRE OUT: ZONE 2, ZONE 3
These analog audio outputs can be connected to the line inputs on amplifiers in Zone 2 and Zone 3.
The SW jacks can be connected to the inputs on powered subwoofers in Zone 2 and Zone 3.
do AC OUTLET (North American model only)
These switched AC outlets can be used to supply power to other AV components. The type and num­ber of outlets depends on the country in which you purchased your AV controller.
See pages 21–44 for hookup information.
14
Page 15

Remote Controller

Installing the Batteries

To open the battery compartment, press
1
the small hollow and slide open the cover.
Insert the three supplied batteries (AA/R6)
2
in accordance with the polarity diagram inside the battery compartment.
Slide the cover shut.
3
Notes:
• If the remote controller doesn’t work reliably, try replacing the batteries.
• Don’t mix new and old batteries or different types of batteries.
• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.
• Expired batteries should be removed as soon as possi­ble to prevent damage from leakage or corrosion.

Aiming the Remote Controller

When using the remote controller, point it toward the AV controller’s remote control sensor, as shown below.
Remote control sensor
STANDBY indicator
30˚
30˚
Notes:
• The remote controller may not work reliably if the AV controller is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.
• If another remote controller of the same type is used in the same room, or the AV controller is installed close to equipment that uses infrared rays, the remote con­troller may not work reliably.
• Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.
• The remote controller may not work reliably if the AV controller is installed in a rack behind colored glass doors. Keep this in mind when installing.
• The remote controller will not work if there’s an obstacle between it and the AV controller’s remote control sensor.
AV controller
Approx. 16 ft. (5 m)
15
Page 16
Remote Controller—Continued

About the Remote Controller Modes

As well as the AV controller, you can also use the remote controller to control your other AV components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the REMOTE MODE buttons.
RECEIVER/TAPE Mode
In RECEIVER/TAPE mode, you can control the AV controller and an Onkyo cassette recorder connected via u.
DVD Mode
By default, you can control an Onkyo DVD player in this mode. By entering the appropriate remote control code, you can control components made by other manufactur­ers (see page 122).
CD/CDR/MD Mode
By default, you can control an Onkyo CD player in this mode. By entering the appropriate remote control code, you can control a CD player, MD recorder, or CD recorder made by another manufacturer (see page 122).
DOCK Mode
This mode is for controlling an Apple iPod in an Onkyo RI Dock. You must enter the appropriate remote control code first (see page 122).
TV and VCR Modes
With these modes, you can control a TV and VCR. You must enter the appropriate remote control code first (see page 122).
CABLE/SAT Mode
In CABLE/SAT mode, you can control a cable or satel­lite TV receiver. You must enter the appropriate remote control code first (see page 122).
ZONE 2/ZONE 3 Modes
These modes are for controlling Zone 2 and Zone 3 (see page 117).
Use the REMOTE MODE buttons to select
1
a mode.
Use the buttons supported by that mode
2
to control the component.
RECEIVER/TAPE mode:
DVD mode: see page 18
CD/MD/CDR mode: see page 19
DOCK mode: see page 20
TV, VCR, CABLE/SAT modes: see page 124
see right column

RECEIVER/TAPE Mode

RECEIVER/TAPE mode is used to control the AV con­troller. It can also be used to control an Onkyo cassette recorder connected via u.
To set the remote controller to RECEIVER/TAPE mode, press the [RECEIVER] REMOTE MODE button.
1
2
bm
3
bn
4
RECEIVER
TAPE/AMP
bo bp
5 6
7
8 9
bq br bs
1
bk
bl
bt ck
cl
Note:
Some of the remote controller functions described in this manual may not work as expected with other compo­nents.
16
Page 17
Remote Controller—Continued
For detailed information, see the pages in parentheses.
a STANDBY button (45)
Sets the AV controller to Standby.
b ON button (45)
Turns on the AV controller.
c INPUT SELECTOR buttons (64)
Used to select the input source.
d MACRO buttons (126)
Used with the Macro function.
e DIMMER button (65)
Adjusts the display brightness.
f Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to select and adjust settings.
g CH +/– button (69)
Selects radio presets.
h SETUP button
Used to change settings.
i DISPLAY button (66)
Displays information about the current input source.
j LISTENING MODE buttons (75)
Used to select the listening modes. The [STEREO], [SURR], and LISTENING MODE [e]/[r] buttons
can be used at any time, regardless of the currently selected remote controller mode.
k TEST TONE, CH SEL, LEVEL–, and LEVEL+
buttons (65, 93)
Used to adjust the level of each speaker.
l LIGHT button
Turns the remote controller’s illuminated buttons on or off.
m D.TUN button (68)
Selects the Direct tuning mode for radio.
n REMOTE MODE buttons (16)
Used to select the remote controller modes. When you press a button, the REMOTE MODE button for the currently selected mode lights up.
o SLEEP button (66)
Used with the Sleep function.
p VOL [q]/[w] button (64)
Adjusts the volume of the AV controller regardless of the currently selected remote controller mode.
q RETURN button
Returns to the previous display when changing set­tings.
r MUTING button (65)
Mutes or unmutes the AV controller.
s Re-EQ button (101)
Turns the Re-EQ function on or off.
t L NIGHT button (102)
Turns the Late Night function on or off.
u AUDIO SEL button (114)
Selects the audio input: analog, digital, HDMI, or multichannel.
TAPE mode
On twin cassette decks, only Deck B can be controlled.
1 Previous and Next [7]/[6] buttons
The Previous [7] button selects the previous track. During playback it selects the beginning of
the current track. The Next [6] button selects the next track.
Depending on how they were recorded, the Previous and Next [7]/[6] buttons may not work prop-
erly with some cassette tapes.
Play [1] button
Starts playback.
Rewind and Fast Forward [5]/[4] buttons
The Rewind [5] button starts rewind. The Fast Forward [4] button starts fast forward.
Reverse Play [t] button
Starts reverse playback.
Stop [2] button
Stops playback.
REC [y] button
Starts recording.
17
Page 18
Remote Controller—Continued

DVD Mode

To set the remote controller to DVD mode, press the [DVD] REMOTE MODE button.
1
2
3
bn
DVD
4
bo
5
6
7
bp
8
9
bq
bk bl
br bs
bm
bt
a STANDBY button
Sets the DVD player to Standby.
b ON button
Turns on the DVD player.
c Number buttons
Used to enter title, chapter, and track numbers, and to enter times for locating specific points.
d TOP MENU button
Selects a DVD’s top menu.
e Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to navigate menus and select items.
f DISC +/– button
Selects discs on a DVD changer.
g SETUP button
Used to access the DVD player’s settings.
h DISPLAY button
Displays information about the current disc, title, chapter, or track, including elapsed time, remaining time, total time, and so on.
i Playback buttons
From left to right: Previous, Play, Next, Fast Reverse, Pause, Stop, Fast Forward, Slow Reverse, and Slow Forward.
j REPEAT button
Used with the repeat playback function.
k AUDIO button
Selects foreign language soundtracks and audio for­mats (e.g., Dolby Digital or DTS).
l OPEN/CLOSE [0] button
Opens and closes the disc tray.
m CLEAR button
Cancels functions and clears entered numbers.
n MENU button
Displays a DVD’s menu.
o RETURN button
Exits the DVD player’s onscreen setup menu.
p RANDOM button
Used with the random playback function.
q PLAY MODE button
Selects play modes on components with selectable play modes.
r SUBTITLE button
Selects subtitles.
s VIDEO OFF button
Turns off the internal video circuitry, eliminating any possibility of interference.
18
Page 19
Remote Controller—Continued

CD/MD/CDR Modes

To control an Onkyo CD player, MD recorder, or CD recorder, or a CD or MD player/recorder made by another manufacturer, press the [CD] REMOTE MODE button to select the CD/MD/CDR remote con­troller mode.
In order to control an Onkyo MD recorder or CD recorder, or a component made by another manufacturer, you must first enter the appropriate remote control code (see page 122).
1
2
3
bl
CD
CDR/MD
4
5
6
bm
7
a STANDBY button
Sets the component to Standby.
b ON button
Set the component to On or Standby.
c Number buttons
Used to enter track numbers and times for locating specific points.
d Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used with some components.
e DISC +/– button
Selects discs on a CD changer.
f DISPLAY button
Displays information about the current disc or track, including elapsed time, remaining time, total time, and so on.
g Playback buttons
From left to right: Previous, Play, Next, Fast Reverse, Pause, Stop, and Fast Forward.
h REC [y] button
Starts recording.
i REPEAT button
Used with the repeat playback function.
j OPEN/CLOSE [0] button
Opens or closes the disc tray or ejects the MiniDisc.
k CLEAR button
Cancels functions and clears entered numbers.
l RETURN button
Used with some components.
m RANDOM button
Used with the random playback function.
n PLAY MODE button
Selects play modes on components with selectable play modes.
8
9
bk
bn
bo
19
Page 20
Remote Controller—Continued

DOCK Mode

Dock mode is for controlling an Apple iPod in an Onkyo RI Dock.
To control an RI Dock, press the [DOCK] REMOTE MODE button to select the DOCK remote controller mode.
In order to control an RI Dock, you must first enter the appropriate remote control code (see page 122).
When Using an RI Dock:
• Connect the RI Dock to the TAPE IN or AUX 1 IN L/R jacks.
• Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK.
• Set the AV controller’s Input Display to “DOCK” (see page 57).
• See to the RI Dock’s instruction manual for more information.
1
2
DOCK
3 4
bm
5
6 7
8 9
bk
bl
bn bo
bp bq
br
bs
a STANDBY button
Turns off the iPod.
b ON button*
Turns on the iPod.
c TOP MENU button
Works as a Mode button when used with a DS-A2 RI Dock.
d Arrow [q]/[w] and ENTER buttons*
Used to navigate menus and select items.
e ALBUM +/– button*
Selects the next or previous album.
f DISPLAY button*
Turns on the backlight for 30 seconds.
g Previous [7] button
Restarts the current song. Press it twice to select the previous song.
h Pause [3] button
Pauses playback. (With 3rd generation iPods, it works as a Play/Pause button.)
i Fast Reverse [5] button
Press and hold to fast reverse.
j PLAYLIST Up/Down [i]/[o] buttons*
Used to select the previous or next playlist on the iPod.
k REPEAT button*
Used with the repeat function.
l MENU button*
Used to access menus.
m Play [1] button
Starts playback. If the component is off, it will turn on automatically. (With 3rd generation iPods, this button works as a Play/Pause button.)
n Next [6] button
Selects the next song.
o Stop [2] button
Stops playback and displays a menu.
p Fast Forward [4] button
Press and hold to fast forward.
q RANDOM button*
Used with the shuffle function.
r PLAY MODE button
Used to select play modes on components with selectable play modes. Works as a Resume button when used with a DS-A2 RI Dock.
20
* Buttons marked with an asterisk (*) are not supported by 3rd
generation iPods.
Page 21

About Home Theater

Enjoying Home Theater

Thanks to the AV controller’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes. You can also enjoy THX Surround EX (THX-certified THX speaker system recommended).
Front left and right speakers
These output the main sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.
Center speaker
This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. For movies it’s used mainly for dialog.
Position it close to your TV (preferably on top) facing forward at about ear level, or at the same height as the front left and right speakers.
Surround left and right speakers
These speakers are used for precise sound positioning and to add realistic ambience.
Position them at the sides of the lis­tener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equally spaced from the listener.
Subwoofer
The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listen­ing position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the way along the front wall, as shown.
Tip: To find the best position for your sub­woofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room and choose the one that provides the most satisfying results.
1/3 of wall position
Surround back left and right speakers
These speakers are necessary to enjoy Dolby Digital EX, DTS-ES Matrix, DTS-ES Discrete, THX Surround EX, etc. They enhance the realism of surround sound and improve sound localization behind the listener. Posi­tion them behind the listener about 2–3 feet (60–100 cm) above ear level.
Corner position
21
Page 22

Connecting the AV Controller

Connecting Your Speakers

The AV controller is designed to be used with a separate multichannel power amplifier. You connect the AV con­troller’s PRE OUT jacks to the amplifier’s inputs, and connect your speakers to the amplifier’s speakers termi­nals. Speaker settings such as crossover frequency and distance are set on the AV controller.
Speaker Configuration
For 7.1-channel surround-sound playback, you need seven speakers and a powered subwoofer.
The following table shows which channels you should use based on the number of speakers you have.
Number of speakers: 2 3 4 5 6 7
Front left ✓✓✓✓✓✓
Front right ✓✓✓✓✓✓
Center ✓✓
Surround left ✓✓✓✓
Surround right ✓✓✓✓
Surround back*
Surround back left
Surround back right
* If you’re using only one surround back speaker, use the SURR
BACK L output.
No matter how many speakers you use, a powered sub­woofer is recommended for a powerful and solid bass.
To get the best from your surround-sound system, you must set the speaker settings. You can do this automati­cally (see page 58) or manually (see page 89).
Using Dipole Speakers
You can use dipole speakers for the surround left and right and surround back left and right speakers. Dipole speakers output the same sound in two directions.
Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround left and right dipole speakers should be positioned so that their arrows point toward your TV or screen, while the sur­round back left and right dipolar speakers should be posi­tioned so that their arrows point toward each other, as shown.
5
1. Subwoofer
2. Front left speaker
3. Center speaker
4. Front right speaker
5. Surround left speaker
Dipole speakers
TV/screen TV/screen
2
3
7 8
1
4
Normal speakers
2
5
6
6. Surround right speaker
7. Surround back left speaker
8. Surround back right speaker
1
3
78
4
6
22
Page 23
Connecting the AV Controller—Continued
Connecting a Powered Subwoofer
Using a suitable cable, connect the AV controller’s SUB­WOOFER PRE OUT to the input on your powered sub­woofer. If your subwoofer is unpowered and you’re using an external amplifier, connect the SUBWOOFER PRE OUT to the amp’s input.
You can also connect a powered subwoofer to the AV controller’s balanced SUBWOOFER PRE OUT XLR jack by using a balanced XLR cable.
Powered
subwoofer
LINE INPUT
LINE INPUT
Powered
subwoofer
INPUT
INPUT
SUBWOOFER
PRE OUT
Balanced
SUBWOOFER
PRE OUT
XLR cable

Connecting a Power Amplifier with RCA Inputs

You can connect the AV controller to a multichannel power amplifier with RCA input jacks by using a multichannel RCA audio cable or several stereo RCA audio cables.
See your multichannel power amplifier’s instruction manual for more information on connecting speakers.
AV controller
Surround
back right
speaker
Multichannel power amplifier
SURROUND BACK RIGHT
INPUT SELECT
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
SURROUND RIGHT
INPUT SELECT
Surround
right
FRONT
RIGHT
INPUT SELECT
Front right
speaker
FUSE
Center
speaker
CENTER
INPUT SELECT
SPEAKER IMPEDANCE
4 OHMS MIN. PER EACH SPEAKER TERMINAL
AC INLET
FRONT
LEFT
INPUT SELECT
12V TRIGGER
IN OUT
Front left
speaker
speaker
SURROUND LEFT
INPUT SELECT
Surround
left
speaker
SURROUND BACK LEFT
SEVEN CHANNEL AMPLIFIER
MODEL NO. RDA-7.1
Surround
back left
speaker
INPUT SELECT
23
Page 24
Connecting the AV Controller—Continued

Connecting a Power Amplifier with XLR Inputs

You can connect the AV controller to a multichannel power amplifier with balanced XLR input jacks by using several XLR audio cables.
The AV controller’s balanced PRE OUT XLR jacks are wired as shown.
See your multichannel power amplifier’s instruction manual for more information on connecting speakers.
AV controller
SURROUND BACK RIGHT
INPUT SELECT
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
Surround
back right
speaker
SURROUND RIGHT
INPUT SELECT
Surround
right
speaker
FRONT
RIGHT
INPUT SELECT
Front right
speaker
FUSE
Center
speaker
CENTER
INPUT SELECT
SPEAKER IMPEDANCE
4 OHMS MIN. PER EACH SPEAKER TERMINAL
AC INLET
FRONT
LEFT
INPUT SELECT
12V TRIGGER
IN OUT
Front left
speaker
SURROUND LEFT
INPUT SELECT
Surround
left
speaker
Multichannel power amplifier
SURROUND BACK LEFT
INPUT SELECT
SEVEN CHANNEL AMPLIFIER
MODEL NO. RDA-7.1
Surround
back left
speaker
24
Page 25
Connecting the AV Controller—Continued

Bi-amping the Front Speakers

The FRONT L/R and SURR BACK L/R outputs can be used with front speakers and surround back speakers, respec­tively, or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing improved bass and treble performance.
• When bi-amping is used, the AV controller is able to feed up to 5.1 speakers in the main room.
• For bi-amping, the FRONT L/R outputs feed the front speakers’ woofer terminals. And the SURR BACK L/R outputs feed the front speakers’ tweeter terminals.
• Once you’ve completed the bi-amping connections shown below and turned on the AV controller, you must set the “Speaker Type” setting to “Bi-Amp” to enable bi-amping (see page 55).
Important:
• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low) terminals.
• Bi-amping can only be used with speakers that support bi-amping. Refer to your speaker manual.
See your multichannel power amplifier’s instruction manual for more information on connecting speakers.
AV controller
SURROUND BACK RIGHT
INPUT SELECT
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
SURROUND RIGHT
INPUT SELECT
Surround right
speaker
FRONT RIGHT
INPUT SELECT
CENTER
INPUT SELECT
SPEAKER IMPEDANCE
4 OHMS MIN. PER EACH SPEAKER TERMINAL
AC INLET
FUSE
Center speaker
Tweeter (high)
Woofer (low)
FRONT
LEFT
INPUT SELECT
12V TRIGGER
IN OUT
SURROUND LEFT
INPUT SELECT
Surround left
speaker
Multichannel power amplifier
SURROUND BACK LEFT
INPUT SELECT
SEVEN CHANNEL AMPLIFIER
MODEL NO. RDA-7.1
Front right speaker
Front left speaker
25
Page 26
Connecting the AV Controller—Continued

Connecting Antenna

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.
The AV controller won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.
North American Model
AM ANTENNA push terminals
FM ANTENNA jack
Other Models
AM ANTENNA push terminals
Use thumbtacks or something similar to
2
fix the FM antenna into position.
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself when using thumbtacks.
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out­door FM antenna instead (see page 27).
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use only.
Assemble the AM loop antenna, inserting
1
the tabs into the base, as shown.
FM ANTENNA jack
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
1
North American Model
FM
75
Other Models
FM75
Once your AV controller is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.
Insert the plug fully into the jack.
Insert the plug fully into the jack.
Connect both wires of the AM loop
2
antenna to the AM push terminals, as shown.
(The antenna’s wires are not polarity sensitive, so they can be connected either way around.)
Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.
North American Model
Push Insert wire Release
26
Page 27
Connecting the AV Controller—Continued
Other Models
Push Insert wire Release
Once your AV controller is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.
Keep the antenna as far away as possible from your AV controller, TV, speaker cables, and power cords.
If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commer­cially available outdoor AM antenna (see page 27).
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out­door FM antenna instead.
Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If cir­cumstances demand it, use a TV/FM antenna splitter, as shown.
TV/FM antenna splitter
To AV controller To TV (or VCR)
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
North American Model
Outdoor antenna
Insulated antenna cable
AM loop antenna
Other Models
Outdoor antenna
FM 75
Notes:
• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.
• For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.
• Outdoor antenna should be located away from possi­ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.
• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock haz­ards.
AM loop antenna
Insulated antenna cable
Outdoor AM antennas work best when installed horizon­tally outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.
27
Page 28
Connecting the AV Controller—Continued
K

About AV Connections

• Before making any AV connections, read the manuals supplied with your other AV components.
• Don’t connect the power cord until you’ve completed and double-checked all AV connections.
Optical Digital Jacks
The AV controller’s optical digital jacks have shutter­type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.
Caution: To prevent shutter damage, hold the optical plug straight when inserting and removing.
AV Cables and Jacks
Video
Cable Jack Description
HDMI
YY
Component video cable
S-Video cable
Composite video cable
CB/
CR/
P
B
P
R
CB/
P
B
CR/
P
R
AV Connection Color Coding
RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right­channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.
Left (white)
Right (red)
(Yellow)
• Push plugs in all the way to make good connections (loose connec­tions can cause noise or malfunc­tions).
• To prevent interference, keep audio and video cables away from power cords and speaker cables.
HDMI
HDMI connections can carry uncompressed stan­dard- or high-definition digital video and audio and offer the best picture and sound quality.
Y
CB/P
B
CR/P
R
Component video separates the luminance (Y) and color difference signals (P picture quality. (Some TV manufacturers label their component video jacks slightly differently.)
S-Video separates the luminance and color signals
S
and provides better picture quality than composite video.
Composite video is commonly used on TVs, VCRs,
V
and other video equipment.
Analog audio
Composite video
R, PB), providing the best
Left (white)
Right (red)
(Yellow)
Right!
Wrong!
Audio
Optical digital audio cable
Coaxial digital audio cable
Balanced XLR cable
Analog audio cable (RCA)
Multichannel analog audio cable (RCA)
Note: The AV controller does not support SCART connections.
28
FRONT CENTER
SUBWOOFER
L
R
OPTICAL
COAXIAL
SURR
MULTI CH
This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for coaxial.
This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for optical.
This cable carries analog audio. Balanced XLR cables are used for better noise immunity and longer cable runs.
This cable carries analog audio. It’s the most common connection format for analog audio and can be found on virtually all AV components.
This cable carries multichannel analog audio and is
SURR BAC
typically used to connect DVD players with a 7.1­channel analog audio output. Several standard analog audio cables can be used instead of a multi­channel cable.
Page 29
Connecting the AV Controller—Continued

Connecting Both Audio & Video

By connecting both the audio and video outputs of your DVD player and other AV components to the AV controller, you can switch the audio and video signals simultaneously simply by changing the input source on the AV controller.
: Signal Flow
Video
Video
Audio
Audio
TV, projector,
etc.
DVD player, etc.
On
Power
Standby
On
O f f
Seven Channel Amplifier
RDA-7.1
Power amplifier and speakers
(see page 26 for hookup details)

Which Connections Should I Use?

The AV controller supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide.
For video components, you must make an audio connection and a video connection.
Video Connection Formats
Video equipment can be connected to the AV controller by using any one of the following video connection formats: composite video, S-Video, component video, or HDMI, the latter offering the best picture quality.
The AV controller can upconvert and downconvert between video formats, depending on the “Monitor Out” setting, which generally determines whether video signals are upconverted for the component video output or the HDMI out­puts.
For optimal video performance, THX recommends that video signals pass through the system without upconver­sion (e.g., component video input through to component video output). It’s also recommended that you set the “Immediate Display” preference to “Off” (see page 109), the “Picture Adjust” setting to the default (see page 104), and the “Resolution” setting to “Through” (see page 49).
“Monitor Out” Setting Set to “HDMI Main” or “HDMI Sub”
With the “Monitor Out” setting set to “HDMI Main” or “HDMI Sub” (see page 46), video input signals flow through the AV controller as
Video Signal Flow Chart
DVD player, etc.
shown, with composite video, S-Video, and component video sources all being upcon­verted for the respective HDMI output. Use the
“HDMI Main” or “HDMI Sub” setting if you connect the AV controller’s HDMI OUT MAIN or HDMI OUT SUB, respectively, to your TV.
AV controller
The composite video, S-Video, and component video outputs pass through their respective input signals as they are.
TV, projector, etc.
Composite S-Video Component
IN
MONITOR OUT
Composite S-Video Component
HDMI
HDMI
29
Page 30
Connecting the AV Controller—Continued
“Monitor Out” Setting Set to “Analog”
With the “Monitor Out” setting set to “Analog” (see page 46), video input signals flow through the AV controller as shown, with composite video and S-Video sources being upconverted for the component video output. Use this set-
ting if you connect the AV controller’s COMPONENT VIDEO MONITOR OUT 1 or 2 to your TV.
Composite video is upconverted to S-Video and S-Video is downconverted to composite video. Note that these conversions only apply to the MONITOR OUT V and S outputs, not the VCR/DVR OUT V and S outputs.
The composite video, S-Video, and component video outputs pass through their respective input signals as they are.
This signal flow also applies when the Monitor Out “Resolution” setting is set to “Through” (see page 49).
Video Signal Flow and the
Resolution
Setting
When the “Monitor Out” setting is set to “Ana­log” (see page 46), if the Monitor Out “Reso­lution” setting is set to anything other than “Through” (see page 49), the video signal flow will be as shown here, with composite video and S-Video sources being upconverted for the component video output.
The composite video, S-Video, and component video outputs pass through their respective analog input signals as they are. HDMI input signals are not output.
Video Signal Flow Chart
DVD player, etc.
AV controller
TV, projector, etc.
Video Signal Flow Chart
DVD player, etc.
AV controller
Composite S-Video Component
IN
MONITOR OUT
Composite S-Video Component
Composite S-Video Component
IN
MONITOR OUT
HDMI
HDMI
HDMI
HDMIComposite S-Video Component
Audio Connection Formats
Audio equipment can be connected to the AV controller by using any of the following audio connection formats: analog, optical, coaxial, analog multichannel, or HDMI.
When choosing a connection format, bear in mind that the AV controller does not convert digital input signals for analog line outputs and vice versa. For example, audio signals con­nected to an optical or coaxial digital input are not output by the analog TAPE OUT.
30
TV, projector, etc.
Audio Signal Flow Chart
DVD player, etc.
Analog
AV controller
MD recorder, etc.
Optical
2
*
Analog
*1 Depends on the “Audio TV Output” setting (see
page 111).
CoaxialMultichannel
Optical
HDMI
HDMI
1
*
Page 31
Connecting the AV Controller—Continued

Connecting a TV or Projector

See “Connecting Components with HDMI” on page 37 for HDMI connection information.
Step 1: Video Connection
Choose a video connection that matches your TV ( , , or ), and then make the connection.
Step 2: Audio Connection
Choose an audio connection that matches your TV ( , , or ), and then make the connection.
A B C
a b c
• With connection , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3.
• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 or Zone 3 as well, use and , or and .)
a b a c
Connection AV controller Signal flow TV
A
B
C
a
b
c
a
COMPONENT VIDEO MONITOR OUT 1
MONITOR OUT S
MONITOR OUT V
GAME/TV IN L/R
DIGITAL COAXIAL IN 2 (VCR/DVR)
DIGITAL OPTICAL IN 1 (GAME/TV)
b c
Component video input
S-Video input
Composite video input
Analog audio L/R output
Digital coaxial output
Digital optical output
C
C
b
B
B
c
a
A
OPTICAL
OUT
Connect one or the other Connection must be assigned (see page 53)
b
If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite
Hint!
receiver to the AV controller and use its tuner to listen to TV programs through the AV controller (see pages 34 and 36).
OUT
YCOAXIAL
PB
R S VIDEO
COMPONENT VIDEO IN
P
TV, projector,
etc.
LR
AUDIO
OUT
IN
VIDEO
IN
31
Page 32
Connecting the AV Controller—Continued

Connecting a DVD player

Step 1: Video Connection
Choose a video connection that matches your DVD player ( , , or If you use connection , you must connect the AV controller to your TV with the same type of connection.
A
A B C
Step 2: Audio Connection
Choose an audio connection that matches your DVD player ( , , or ), and then make the connection.
a b c
), and then make the connection.
• With connection , you can listen to and record audio from a DVD or listen in Zone 2 or Zone 3.
• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 or Zone 3 as well, use and , or and .)
a b a c
a
b c
• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the
main left and right outputs for connection .
Connection AV controller Signal flow DVD player
A
B
C
a
b
c
COMPONENT VIDEO IN 1 (DVD)
DVD IN S
DVD IN V
DVD IN L/R
DIGITAL COAXIAL IN 1 (DVD)
DIGITAL OPTICAL IN 1 (GAME/TV)
a
Component video output
S-Video output
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
C
C
b
B
B
c
a
A
OPTICAL
OUT
Connect one or the other Connection must be assigned (see page 53)
c
OUT
32
YCOAXIAL
PB
COMPONENT VIDEO OUT
LR
R S VIDEO
P
AUDIO
OUT
DVD player
OUT
VIDEO
OUT
To connect a DVD player or DVD-Audio/SACD-capable player with a multichannel analog audio output, see page 33.
Page 33
Connecting the AV Controller—Continued
Hooking Up the Multichannel Input
If your DVD player supports multichannel audio formats such as DVD-Audio and SACD, and it has a multichannel analog audio output, you can connect it to the AV controller’s multichannel input.
Use a multichannel analog audio cable, or several normal audio cables, to connect the AV controller’s MULTI CH: FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV controller’s SURR BACK L/R jacks.
Before using the multichannel input, you must assign it to an input selector. See “Analog Audio Input Setup” on page 54. To select the multichannel input, see “Selecting Audio Inputs” on page 114. To adjust the subwoofer sensitivity for the multichannel input, see “Subwoofer Input Sensitivity” on page 111.
7.1 ch
5.1 ch
FRONT
FRONT CENTER
L
R
SUBWOOFER
R
CENTER SUB
SURR
SURR BACK
L
MULTI CH
LLR
WOOFER
SURROUND
R
LR
SURR BACK
DVD player
33
Page 34
Connecting the AV Controller—Continued

Connecting a VCR or DVD Recorder for Playback

Hint!
With this hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs via the AV controller, which is useful if your TV has no audio outputs.
Step 1: Video Connection
Choose a video connection that matches your VCR or DVD recorder ( , , or If you use connection , you must connect the AV controller to your TV with the same type of connection.
A
A B C
), and then make the connection.
Step 2: Audio Connection
Choose an audio connection that matches your VCR or DVD recorder ( , , or ), and then make the connection.
• With connection , you can listen to the VCR or DVD recorder in Zone 2 or Zone 3.
• To enjoy Dolby Digital and DTS, use connection or . (To listen in Zone 2 or Zone 3 as well, use and , or and .)
b a c
Connection AV controller Signal flow VCR or DVD recorder
A
B
C
a
b
c
a
COMPONENT VIDEO IN 2
VCR/DVR IN S
VCR/DVR IN V
VCR/DVR IN L/R
DIGITAL COAXIAL IN 2 (VCR/DVR)
DIGITAL OPTICAL IN 1 (GAME/TV)
b c a
a b c
Component video output
S-Video output
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
34
Connection
must be
A
assigned (see page 52)
b
c
A
OPTICAL
OUT
Connect one or the other Connection must be assigned (see page 53)
c
OUT
YCOAXIAL
COMPONENT VIDEO OUT
PB
LR
R S VIDEO
P
AUDIO
OUT
VCR,
DVD recorder
OUT
VIDEO
OUT
C
C
B
B
a
Page 35
Connecting the AV Controller—Continued

Connecting a VCR or DVD Recorder for Recording

Step 1: Video Connection
Choose a video connection that matches your VCR or DVD recorder ( or ), and then make the connection. The video source to be recorded must be connected to the AV controller via the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your VCR or DVD recorder ( or ), and then make the connection.
Connection AV controller Signal flow VCR or DVD recorder
A
B
a
b
VCR/DVR OUT S
VCR/DVR OUT V
VCR/DVR OUT L/R
DIGITAL OPTICAL OUT
A B
a b
S-Video input
Composite video input
Audio L/R input
Digital optical input
B
A
a
b
LR
OPTICAL
IN
AUDIO
Notes:
• The AV controller must be turned on for recording. Recording is not possible while it’s on Standby mode.
• If you want to record directly from your TV or another video source without going through the AV controller, connect the audio and video outputs from your TV or other video component directly to the recording VCR/DVD recorder’s audio and video inputs. See the manuals supplied with your TV or VCR/DVD recorder for details.
• Video signals connected to composite video inputs can only be recorded via the VCR/DVR OUT V jack. So if your source TV or VCR is connected to a composite video input, the recording VCR/DVR must be connected to the VCR/DVR OUT V jack. Likewise, video signals connected to S-Video inputs can only be recorded via the VCR/DVR OUT S jack. So if your source TV or VCR is connected to an S-Video input, the recording VCR/DVD recorder must be connected to the VCR/DVR OUT S jack.
S VIDEO
IN
DVD recorder
IN
VCR,
VIDEO
IN
35
Page 36
Connecting the AV Controller—Continued

Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source

Hint!
With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV controller, which is useful if your TV has no audio outputs.
Step 1: Video Connection
Choose a video connection that matches the video source ( , , or If you use connection , you must connect the AV controller to your TV with the same type of connection.
A
A B C
), and then make the connection.
Step 2: Audio Connection
Choose an audio connection that matches the video source ( , , or ), and then make the connection.
• With connection , you can listen to and record audio from the video source or listen in Zone 2 or Zone 3.
a
• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 or Zone 3 as well, use and , or and .)
a b a c
Connection AV controller Signal flow Video source
A
B
C
a
b
c
COMPONENT VIDEO IN 3
CBL/SAT IN S
CBL/SAT IN V
CBL/SAT IN L/R
DIGITAL COAXIAL IN 3 (CBL/SAT)
DIGITAL OPTICAL IN 2 (CD)
b c
a b c
Component video output
S-Video output
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
b
c
A
OPTICAL
OUT
Connect one or the other Connection must be assigned (see page 53)
c
36
OUT
YCOAXIAL
PB
COMPONENT VIDEO OUT
LR
R S VIDEO
P
AUDIO
OUT
Satellite, cable, set-top box, etc.
OUT
VIDEO
OUT
C
BCB
a
Page 37
Connecting the AV Controller—Continued

Connecting Components with HDMI

About HDMI
Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, or multichannel PCM).
*1
The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface) with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.)
*2
The AV controller uses HDCP (High-bandwidth Digital Content Protection) will display a picture.
The AV controller’s HDMI interface is based on the following standard: Repeater System, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD,
Dolby Digital Plus, SA-CD, and Multichannel PCM
, so only HDCP-compatible components
Supported Audio Formats
• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)
• Multichannel linear PCM (7.1 ch, 32–192 kHz, 16/20/24 bit)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution, DTS-HD Mas­ter Audio)
Your DVD player must be able to output these formats from its HDMI OUT.
, so TVs and displays
About Copyright Protection
The AV controller supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection system for digital video signals. Other devices connected to the AV controller via HDMI must also support HDCP.
Use a commercially available HDMI cable (supplied with some components) to connect the AV controller’s HDMI OUT MAIN or HDMI OUT SUB to the HDMI input on your TV or projector.
*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999. *2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to
protect video content and requires a HDCP-compatible device to display the encrypted video.
*3 DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open
industry group’s objective is to address the industry's requirements for a digital connectivity specification for high-performance PCs and digital displays.
37
Page 38
Connecting the AV Controller—Continued
Making HDMI Connections
Step 1:
Use HDMI cables to connect the AV controller’s HDMI jacks to your HDMI-compatible Blu-ray player/DVD player, TV, projector, and so on.
Step 2:
Assign each HDMI IN to an input selector. See “Video Input Setup” on page 50.
Video Signals
Digital video signals received by the HDMI IN jacks are normally output by the HDMI MAIN OUT and SUB OUT for display on your TV. Composite video, S-Video, and component video sources can be upconverted for the HDMI outputs. See “Video Connection Formats” on page 29 for more information.
Audio Signals
Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV controller. Normally, they are not output by the HDMI outputs, unless the “Audio TV Output” setting is set to “On” (see page 111).
To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the “Audio TV
Hint!
Output” setting to “On” (see page 111), and set your DVD player’s “Audio TV Output” setting to PCM.
Blu-ray player/
DVD player
HDMI OUT
HDMI
HDMI
IN
TV
HDMI
Notes:
• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.
• When listening to an HDMI component through the AV controller, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV controller). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV controller or the sound may be cut off.
• When the “Audio TV Output” setting is set to “On” (see page 111), or “TV Control” is set to “Enable” (see page 112) and you’re listening through your TV’s speakers, if you turn up the AV controller volume control, the sound will be output by the AV controller’s speakers. To stop the AV controller’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV controller’s volume.
• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details.
38
Page 39
Connecting the AV Controller—Continued

Connecting a Game Console

Step 1: Video Connection
Choose a video connection that matches your game console ( , , or If you use connection , you must connect the AV controller to your TV with the same type of connection.
A
A B C
Step 2: Audio Connection
Choose an audio connection that matches your DVD player ( , , or ), and then make the connection.
a b c
), and then make the connection.
• With connection , you can listen to and record audio from your game console or listen in Zone 2 or Zone 3.
• To enjoy Dolby Digital and DTS, use connection . (To record or listen in Zone 2 or Zone 3 as well, use and .)
b
a
b a
Connection AV controller Signal flow Game console
A
B
C
a
b
COMPONENT VIDEO IN 3
GAME/TV IN S
GAME/TV IN V
GAME/TV IN L/R
DIGITAL OPTICAL IN 1 (GAME/TV)
Component video output
S-Video output
Composite video output
Analog audio L/R output
Digital coaxial output
C
BCB
b
a
Connection
A
must be assigned (see page 52)
A
OPTICAL
OUT
YPB
COMPONENT VIDEO OUT
LR
R S VIDEO
P
AUDIO
OUT
Game Console
OUT
VIDEO
OUT
39
Page 40
Connecting the AV Controller—Continued

Connecting a Camcorder or Other Device

Step 1: Video Connection
Choose a video connection that matches your camcorder ( or ), and then make the connection.
Step 2: Audio Connection
Choose an audio connection that matches your camcorder ( or ), and then make the connection.
A B
a b
AUX 2 INPUT
DIGITAL
b
a
AUX 2 INPUT
S VIDEO
AUX 2 INPUT
VIDEO
A
S VIDEO
OUT
B
VIDEO
OUT
Camcorder, etc.
Connection AV controller Signal flow Camcorder
A
B
a
b
AUX 2 INPUT S VIDEO
AUX 2 INPUT VIDEO
AUX 2 INPUT L-AUDIO-R
AUX 2 INPUT DIGITAL
AUX 2 INPUT
LR
AUDIO
LR
AUDIO
OUT
OPTICAL
Composite video output
Analog audio L/R output
OUT
S-Video output
Digital optical output
40
Page 41
Connecting the AV Controller—Continued

Connecting a CD Player or Turntable

CD Player or Turntable (MM) with Built-in Phono Preamp
Step 1:
Choose a connection that matches your CD player ( , , or ). Use connection for a turntable with a built-in phono preamp.
IN 2
b
(VCR/DVR)
COAXIAL
OUT
IN
L
OPTICAL
R
IN 2
CD
(CD)
LR
OPTICAL
AUDI O
OUT
OUT
Connect one or the other Connection
must be
b
assigned (see page 53)
a
COAXIAL
a b c a
c
CD player
IN
L
R
CD
OUTPUT
a
Turntable (MM) with
built-in phono preamp
L
R
AUDI O
• With connection , you can listen to and record audio from the CD player or listen in Zone 2 or Zone 3.
• To connect the CD player digitally, use connection or . (To record or listen in Zone 2 or Zone 3 as well, use and , or and .)
a b a c
a
b c
Connection AV controller Signal flow CD or turntable
a
b
c
DIGITAL COAXIAL IN 2 (VCR/DVR)
DIGITAL OPTICAL IN 2 (CD)
CD IN L/R
Analog audio L/R output
Digital coaxial output
Digital optical output
Turntable (MM) with no Phono Preamp Built-in
The AV controller’s PHONO IN is designed for use with a moving magnet (MM) type cartridge.
Use an analog audio cable to connect the AV controller’s PHONO IN L/R jacks to the audio output on your turn­table.
Notes:
• If your turntable has a ground wire, connect it to the AV controller’s GND screw. With some turntables, connecting the ground wire may produce an audible hum. If this happens, disconnect it.
• If your turntable has a moving coil (MC) type car­tridge, you’ll need a commercially available MC head
IN
L
R
PHONO
amp or MC transformer. Connect your turntable to the head amp or transformer, and connect that to the AV controller’s PHONO IN L/R jacks.
AUDIO
OUTPUT
L
• You can also use a phono equalizer to connect a turn­table with an MC-type cartridge. See your phono
R
equalizer’s manual for details.
41
Page 42
Connecting the AV Controller—Continued

Connecting a Cassette, CDR, MiniDisc, or DAT Recorder

Step 1:
Choose a connection that matches your recorder ( , , , or ), and then make the connection.
COAXIAL
b
IN 2
(VCR/DVR)
c
OPTICAL
IN 2
(CD)
OPTICAL
d
a b c d
IN
L
R
L
R
a
TAPE
a
TAPE
Connect one
or the other
• With connection , you can play and record or listen in Zone 2 or Zone 3.
COAXIAL
OUT
OPTICAL
OUT
OPTICAL
a
LR
IN
AUDIO
• To connect the recorder digitally for playback, use connections and , or and .
• To connect the recorder digitally for recording, use connection .
IN
LR
AUDIO
OUT
a b a c
d
Cassette, CDR, MD, etc.
Connection AV controller Signal flow Cassette, CDR, MD, or DAT recorder
a
b
DIGITAL COAXIAL IN 2 (VCR/DVR)
c
d
TAPE IN L/R
TAPE OUT L/R
DIGITAL OPTICAL IN 2 (CD)
DIGITAL OPTICAL OUT
⇐ ⇒
Analog audio L/R output
Analog audio L/R input
Digital coaxial output
Digital optical output
Digital optical input

Connecting a Balanced Audio Source

You can connect a balanced audio source to the AV controller’s BALANCE L/R XLR jacks by using two XLR audio cables. To use the balanced input, you must assign it to an input selector (see page 54). If you connect a mono source, use the BALANCE L XLR jack and set the “Balance Input” setting to “Mono” (see page 54). The AV controller’s balanced INPUT XLR jacks are wired as shown.
12
3
Stereo audio source with
balanced XLR output
42
Page 43
Connecting the AV Controller—Continued

Connecting an RI Dock

If Your iPod Doesn’t Support Video:
Not all iPod models output video. For information about which iPod models are supported by the RI Dock, see the RI Dock’s instruction manual.
Connect your RI Dock’s audio output jacks to the AV controller’s AUX 1 IN L/R jacks. (Onkyo DS-A2X hookup shown below.)
If Your iPod Supports Video:
Connect your RI Dock’s audio output jacks to the AV controller’s AUX 1 IN L/R jacks, and connect its video output jack to the AV controller’s AUX 1 IN V
IN
L
R
jack. (Onkyo DS-A2X hookup shown below.)
V
IN
L
R
If you have an Onkyo DS-A1 RI Dock
• Connect its video output jack to the AV controller’s AUX 1 jack.
Notes:
• Connect the RI Dock to the AV controller with an u cable (see page 44).
• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.
• Set the AV controller’s Input Display to “DOCK” (see page 57).
• By using the [DOCK] REMOTE MODE button on the remote controller of the AV controller to change the
remote mode to “DOCK”, you can operate your iPod in the RI Dock (see page 20). If you cannot operate it, you will need to enter the appropriate remote control code (see page 122).
• See the RI Dock’s instruction manual for more information.

Connecting the Power Cords of Other Components (North American model only)

The AV controller has AC outlet on its rear panel that can be used to connect the power cords of other components that you intend to use with the AV controller. These components can then be left turned on so that they turn on and off as and when the AV controller is set to On or Standby.
Caution:
• Make sure that the total capacity of the components that you con­nect to the AC OUTLET does not exceed the stated capacity.
Notes:
• When the “HDMI Control” setting is set to “Enable” (page 111), the AC outlet are on all the time regardless of whether the AV con­troller is set to On or Standby, or Ready mode in this case, so any components connected to them cannot be turned on or off automat­ically.
• Onkyo components connected via u should be connected directly to a wall outlet, not an AC OUTLET on the AV controller.
AC OUTLET
AC 120V
60Hz
SWITCHED
120W 1A MAX.
North American model
43
Page 44
Connecting the AV Controller—Continued
Connecting Onkyo u Components
Step 1: Make sure that each Onkyo component is connected to the AV controller with an analog audio cable (RCA). Step 2: Make the necessary u connections (see illustration below).
Step 3: If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 57).
With u (Remote Interactive), you can use the following special functions:
Auto Power On/Standby
When you start playback on a component connected via u, if the AV controller is on Standby, it will automatically turn on and select that component as the input source. Similarly, when the AV controller is set to Standby, all compo­nents connected via u will also go on Standby. This function will not work with components that are connected to an AC OUTLET on the AV controller.
Direct Change
When playback is started on a component connected via u, the AV controller automatically selects that component as the input source. If your DVD player is connected to the AV controller’s multichannel input, you’ll need to press the [AUDIO SEL] button repeatedly and select Multich to hear all channels (see page 74), as the Direct Change u func­tion selects the DVD IN L/R jacks.
Remote Control
You can use the AV controller’s remote controller to control your other u-capable Onkyo components. You must enter the appropriate remote control code first (see page 123). And remember to point the remote controller at the AV con­troller and not the other component.
Notes:
• Use only u cables for u connections. u cables are supplied with Onkyo players (DVD, CD, etc.).
• Some components have two u jacks. You can con-
IN
L
R
CD
nect either one to the AV controller. The other jack is for connecting additional u-capable components.
• Connect only Onkyo components to u jacks. Con­necting other manufacturer’s components may cause a malfunction.
• Some components may not support all u functions. Refer to the manuals supplied with your other Onkyo components.
• While Zone 2 or Zone 3 is on, the Auto Power On/Standby and Direct Change u functions do not work.
REMOTE CONTROL
e.g., CD player
e.g., DVD player
FRONT
ANALOG
AUDIO OUT
ANALOG
AUDIO OUT
L
R
DVD
LR
LR

Connecting the Power Cord

• Before connecting the power cord, connect all your speakers and AV components.
• Connect the power cord to the AV controller’s AC INLET.
• Plug the other end of the power cord into a suitable wall outlet.
• Turning on the AV controller may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV controller into a different branch circuit.
44
Page 45

Turning On the AV Controller

• North American model • Other models
ON/STANDBY ON/STANDBY
STANDBY indicator

Turning On and Standby

1
2
AV controller
or
Remote
controller
Set the [POWER] switch to the ON position ( ).
(Skip this step if you have the North American model.)
The AV controller enters Standby mode, and the STANDBY indicator comes on.
On the AV controller, press the [ON/STANDBY] button.
On the remote controller, press the [RECEIVER] REMOTE MODE button, followed by the [ON] button.
The AV controller comes on, the display lights up, and the STANDBY indicator goes off.
Pressing the remote controller’s [ON] button again will turn on any components con­nected via u.
STANDBY indicator
POWER
STANDBY
ON
RECEIVER
To turn the AV controller off, press the [ON/STANDBY] button, or press the remote controller’s [STANDBY] button. The AV controller will enter Standby mode. To pre­vent any loud surprises the next time you turn on the AV controller, turn down the volume before you turn it off.
For non-North American models: To completely shut down the AV controller, set the [POWER] switch to the OFF position ( ).
Up and Running in a Few Easy Steps
To get your system up and running with the minimum of fuss, here’s a few pointers to help you configure the AV controller before you use it for the very first time. These settings only need to be made once.
Do the automatic speaker setup—this is essential!
See “Automatic Speaker Setup (Audyssey MultEQ page 58.
Did you connect your TV to an HDMI OUT or COMPONENT VIDEO MONITOR OUT 1 or 2?
If you did, see “Monitor Out Setup” on page 49.
Did you connect a component to an HDMI input, component video input, or digital audio input?
If you did, see “Video Input Setup” on page 50, “Component Video Setup” on page 52, or “Digital Audio Input Setup” on page 53 respectively.
Did you connect an Onkyo MD recorder, CD recorder, or RI Dock?
If you did, see “Changing the Input Display” on page 57.
®
XT)” on
HDMI
OUT IN
Y
P
B
PR
TAPE
MD recorder, CD recorder, RI Dock
COAXIAL
OPTICAL
45
Page 46

First Time Setup

This section explains the settings that you need to make before using the AV controller for the very first time.

Monitor Setup

On the “Monitor Out” settings, you can select whether or not to have the video sources’ images output through the HDMI OUT, as well as whether to have the onscreen setup menu output through the HDMI OUT or through an analog output.
1, 2
If you connect your TV to the COMPONENT VIDEO MONITOR OUT 1 or 2, set the “Monitor Out” setting to “Analog” so that the onscreen setup menus are displayed and composite video and S-Video sources are upcon­verted* and output by the COMPONENT VIDEO MON­ITOR OUT 1 or 2.
Composite video, S-Video
Composite video, S-Video
If you connect your TV to the HDMI OUT MAIN or HDMI OUT SUB, set the “Monitor Out” setting to “HDMI Main” or “HDMI Sub” so that the onscreen setup menus are displayed and composite video, S­Video, and component video sources are upconverted* and output by the HDMI OUT MAIN or HDMI OUT SUB. The onscreen setup menus are displayed on the HDMI OUT MAIN or HDMI OUT SUB only.
Component video
IN
OUT
Component video
1
2
Note:
See page 29 for charts showing how the “Monitor Out” and “Resolution” (see pages 49, 50) settings affect the video signal flow through the AV controller.
Press the [HDMI OUT] button.
The current setting is displayed.
Press the [HDMI OUT] button repeatedly to select:
Analog:
Select this if your TV is connected to the COMPONENT VIDEO MONITOR OUT 1 or 2, S MONI­TOR OUT, or V MONITOR OUT.
HDMI Main:
Select this if your TV is connected to the HDMI OUT MAIN.
HDMI Sub:
Select this if your TV is connected to the HDMI OUT SUB.
Note:
When “HDMI Main” or “HDMI Sub” is selected, the onscreen setup menus are output by only the HDMI outputs.
If you’re not using the HDMI outputs and select “HDMI Main” or “HDMI Sub” by mistake and the menus dis­appear, press the [HDMI OUT] but­ton to select “Analog”.
Composite video, S-Video,
component video
IN
OUT
Composite video, S-Video,
component video
You can specify the output resolution for the HDMI OUT MAIN or HDMI OUT SUB and COMPONENT VIDEO MONITOR OUT and have the AV controller upconvert the picture resolution as necessary to match the resolution supported by your TV (see page 104).
HDMI
HDMI
46
Page 47
First Time Setup—Continued
In this Instruction Manual, illustrations from the onscreen menu or explanations referring to the menu will be in the same language as the Instruction Manual. The default Language setting for the onscreen menu is English. If your Instruction Manual is in a language other than English, first follow the instructions below to change the Language.

Selecting the Language used for the onscreen setup menus

This setting determines the language used for the onscreen setup menus. You can select: English, German, French, Spanish, Italian, Dutch, Swedish, or Japanese.
1
2
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [ q]/[w] but­tons to select “6. Miscella­neous”, and then press [ENTER].
The “Miscellaneous” menu appears.
6. Miscellaneous
1. Volume Setup
2. OSD Setup
3. 12V Trigger A Setup
4. 12V Trigger B Setup
5. 12V Trigger C Setup
4
5
Use the Up and Down [q]/[w] but­tons to select “Language”, and then use the Left and Right
[e]/[r] buttons to select:
English, German, French, Spanish, Italian, Dutch, Swedish, Japanese
Press the [SETUP] button.
The setup menu closes.
3
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “2. OSD Setup”, and then press [ENTER].
The “OSD Setup” menu appears.
6–2. OSD Setup Immediate Display Monitor Type Display Position TV Format Language
MOVE VALUE RETURN
RETURN
On
16 : 9
Bottom
Auto
English
SETUP
EXIT
Note:
The “TV Format” (*) setting is not available on the North American mod­els.
47
Page 48
First Time Setup—Continued
2
1
Menus for First Time Setup
Submenus
SETUP
p. 49
p. 54
EXIT
1
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
ENTER
MOVE ENTER RETURN
RETURN

Using the Onscreen Setup Menus

Carry out the settings for the AV controller by using the Onscreen Setup Menu.
1
2
Press the [RECEIVER] button fol­lowed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
MENU
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Lock Setup
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select submenu and then press [ENTER].
The submenu appears. Press the [SETUP] button to close the
menu. Press the [RETURN] button to return to
the previous menu.
Main menu
MENU
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Lock Setup
MOVE ENTER RETURN
ENTER
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
MOVE ENTER RETURN
RETURN
SETUP
EXIT
6. Miscellaneous
1. Volume Setup
2. OSD Setup
3. 12V Trigger A Setup
4. 12V Trigger B Setup
5. 12V Trigger C Setup
MOVE ENTER RETURN
7. Hardware Setup
1. Remote Control
2. Zone2/Zone3
3. Tuner
4. Analog Multich
5. HDMI
6. Network
MOVE ENTER RETURN
ENTER
ENTER
ENTER
RETURN
RETURN
RETURN
SETUP
SETUP
SETUP
p. 55
EXIT
p. 56
EXIT
p. 57
EXIT
48
Page 49
First Time Setup—Continued
6

Monitor Out Setup

1
2, 3
2–
1, 7
If you connect your TV to the COMPONENT VIDEO MONITOR OUT 1 or 2, set the “Monitor Out” setting to “Analog” so that the onscreen setup menus are displayed and composite video and S-Video sources are upcon­verted and output by the COMPONENT VIDEO MON­ITOR OUT 1 or 2.
If you connect your TV to the HDMI OUT MAIN or HDMI OUT SUB, set the “Monitor Out” setting to “HDMI Main” or “HDMI Sub”, respectively, so that the onscreen setup menus are displayed and composite video, S-Video, and component video sources are upconverted and output by the HDMI OUT MAIN or HDMI OUT SUB.
You can specify the output resolution for the HDMI out­puts and COMPONENT VIDEO outputs and have the AV controller upconvert the picture resolution as neces­sary to match the resolution supported by your TV.
1
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
2
3
4
Use the Up and Down [q]/[w] but­tons to select “1. Input/Output Assign”, and then press [ENTER].
The “Input/Output Assign” menu appears.
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
Use the Up and Down [q]/[w] but­tons to select “1. Monitor Out”, and then press [ENTER].
The “Monitor Out” menu appears.
1–1. Monitor Out
Monitor Out
Resolution Brightness Contrast Hue Saturation
MOVE VALUE RETURN
RETURN
Analog
Through
0 0 0 0
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “Monitor Out”, and
use the Left and Right [e]/[r] buttons to select:
Analog:
Select this if your TV is connected to the COMPONENT VIDEO MONITOR OUT 1 or 2, S MONI­TOR OUT, or V MONITOR OUT.
HDMI Main:
Select this if your TV is connected to the HDMI OUT MAIN.
HDMI Sub:
Select this if your TV is connected to the HDMI OUT SUB.
Note:
When “HDMI Main” or “HDMI Sub” is selected, the onscreen setup menus are output by only the HDMI outputs.
If you’re not using the HDMI outputs and select “HDMI Main” or “HDMI Sub” by mistake and the menus dis­appear, press the AV controller’s [HDMI OUT] button so that “Moni­tor Out: Analog” appears on the dis­play.
49
Page 50
First Time Setup—Continued
5
6
Use the Up and Down [q]/[w] but­tons to select “Resolution”, and
use the Left and Right [e]/[r] buttons to select:
Through:
Select this to pass video through the AV controller at the same resolution and with no conversion.
Auto:
Select this to have the AV controller automatically convert video at reso­lutions not supported by your TV. (Not available when the “Monitor Out” setting is set to “Analog”.)
480p:
Select this for 480p output and video conversion as necessary.
720p:
Select this for 720p output and video conversion as necessary.
1080i:
Select this for 1080i output and video conversion as necessary.
1080p:
Select this for 1080p output and video conversion as necessary. (Not available when the “Monitor Out” setting is set to “Analog”.)
Source:
Output will be according to the res­olution level which was set with Resolution inside Source: 4-4. Picture Adjust. (Setting for each Source becomes possible.)
Use the Up and Down [q]/[w] but­tons to select “Component Out
2”, and use the Left and Right
[e]/[r] buttons to select:
Monitor:
Select this if you’ve connected the COMPONENT VIDEO MONI­TOR OUT 2/ZONE 2 OUT to a TV or other component in your main room.
Zone 2:
Select this if you’ve connected the COMPONENT VIDEO MONI­TOR OUT 2/ZONE 2 OUT to a TV
in Zone 2. When Monitor is selected, the COM­PONENT VIDEO MONITOR OUT 2/ZONE 2 OUT outputs the same video as the COMPONENT VIDEO MONITOR OUT 1.
7
Notes:
• If the video source contains information that restricts output at high-resolutions, 720p or 1080i content will not be converted.
• See page 30 for charts showing how the “Monitor Out” and “Resolution” settings affect the video signal flow through the AV controller.
• This procedure can also be performed on the AV con­troller by using its [SETUP] button, arrow buttons, and [ENTER] button.
Press the [SETUP] button.
Setup closes.

Video Input Setup

HDMI Input Setup
If you connect a video component to an HDMI IN, you must assign that input to an input selector. For example, if you connect your DVD player to HDMI IN 1, you must assign HDMI IN 1 to the DVD input selector.
By default, none of the HDMI inputs are assigned. If you’ve connected your TV to the AV controller with
an HDMI cable, you can set the AV controller so that composite video, S-Video, and component video sources are upconverted can set this for each input selector by selecting the “- - -” option.
Composite video, S-Video,
component video
Composite video, S-Video,
component video
1
*
and output by the HDMI outputs. You
HDMI
IN
OUT
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
HDMI
50
Page 51
First Time Setup—Continued
2
3
Use the Up and Down [q]/[w] but­tons to select “1. Input/Output Assign”, and then press [ENTER].
The “Input/Output Assign” menu appears.
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
Use the Up and Down [q]/[w] but­tons to select “2. HDMI Input”, and then press [ENTER].
The “HDMI Input” menu appears.
1–2. HDMI Input DVD VCR/DVR CBL/SAT GAME/TV AUX1 AUX2
MOVE VALUE RETURN
RETURN
- - -
- - -
- - -
- - -
- - -
- - -
SETUP
EXIT
Notes:
• For composite video, S-Video, and component video upconversion for the HDMI OUT MAIN or HDMI OUT SUB, the “Monitor Out” setting must be set to “HDMI Main” or “HDMI Sub”, respectively (see page 49), and the “HDMI Input” setting must be set to “- - -”. See page 29 for more information on video sig­nal flow and upconversion.
• When an HDMI IN is assigned to an input selector as explained here, the digital audio input for that input selector is automatically set to the same HDMI IN. See “Digital Audio Input Setup” on page 53.
• The “TUNER” input selector cannot be assigned and is fixed at the “- - -” option.
• This procedure can also be performed on the AV con­troller by using its [SETUP] button, arrow buttons, and [ENTER] button.
4
5
Use the Up and Down [q]/[w] but­tons to select an input selector, and use the Left and Right
[e]/[r] buttons to select:
HDMI1, HDMI2, HDMI3, HDMI4:
Select the HDMI IN to which the video component has been con­nected.
- - -:
Output composite video, S-Video, and component video sources from the HDMI OUT. The video output signal from the HDMI OUT is the one configured in “Component
Video Setup” (see page 52). Each HDMI IN cannot be assigned to more than one input selector. When HDMI1 - HDMI4 have already been assigned, you must set first any unused input selectors to “- - -” or you will be unable to assign HDMI1 - HDMI4 to input selector.
Press the [SETUP] button.
Setup closes.
51
Page 52
First Time Setup—Continued
Component Video Setup
If you connect a video component to a COMPONENT VIDEO IN, you must assign that input to an input selector. For example, if you connect your DVD player to COMPONENT VIDEO IN 3, you must assign COM­PONENT VIDEO IN 3 to the DVD input selector.
By default, the DVD input selector is assigned to COM­PONENT VIDEO IN 1, and all of the other input selec­tors are assigned to the “- - -” option.
Input selector Default assignment
DVD IN 1
VCR/DVR ---
CBL/SAT ---
GAME/TV ---
AUX1 ---
AUX2 ---
TAPE - - -
TUNER - - - (Fixed)
CD ---
PHONO ---
If you’ve connected your TV to the AV controller with a component video cable, you can set the AV controller so that composite video and S-Video sources are upcon­verted* and output by the COMPONENT VIDEO MON­ITOR OUT 1 or 2. You can set this for each input selector by selecting the “- - -” option.
Composite video, S-Video
Composite video, S-Video
1
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
OUT
Component video
IN
Component video
2
3
4
5
Use the Up and Down [q]/[w] but­tons to select “1. Input/Output Assign”, and then press [ENTER].
The “Input/Output Assign” menu appears.
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
Use the Up and Down [q]/[w] but­tons to select “3. Component Video Input”, and then press [ENTER].
The “Component Video Input” menu appears.
1–3. Component Video Input DVD VCR/DVR CBL/SAT GAME/TV AUX1 AUX2
MOVE VALUE RETURN
RETURN
IN1
- - -
- - -
- - -
- - -
- - -
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select an input selector, and use the Left and Right
[e]/[r] buttons to select:
IN1: Use the video component
connected to COMPONENT
VIDEO IN 1.
IN2: Use the video component
connected to COMPONENT
VIDEO IN 2.
IN3: Use the video component
connected to COMPONENT
VIDEO IN 3.
---: Output composite video and S-Video sources from the COMPONENT VIDEO MONITOR OUT.
Press the [SETUP] button.
Setup closes.
52
Notes:
• For composite video and S-Video upconversion for the COMPONENT VIDEO MONITOR OUT 1 or 2, the “Monitor Out” setting must be set to “Analog” (see page 49), and the “Component Video Input” set­ting must be set to “- - -”. See page 30 for more infor­mation on video signal flow and upconversion.
• This procedure can also be performed on the AV con­troller by using its [SETUP] button, arrow buttons, and [ENTER] button.
Page 53
First Time Setup—Continued

Digital Audio Input Setup

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to OPTICAL IN 2, you must assign OPTICAL IN 2 to the “CD” input selector.
Here are the default assignments.
Input selector Default assignment
DVD COAX1
VCR/DVR COAX2
CBL/SAT COAX3
GAME/TV OPT1
AUX1 - - -
AUX2 FRONT (Fixed)
TAPE - - -
TUNER - - - (Fixed)
CD OPT2
PHONO - - -
1
2
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] but­tons to select “1. Input/Output Assign”, and then press [ENTER].
The “Input/Output Assign” menu appears.
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
4
5
Use the Up and Down [q]/[w] but­tons to select an input selector, and then use the Left and Right
[e]/[r] buttons to select: “COAX1”, “COAX2”, “COAX3”, “OPT1”, “OPT2”, or “- - - (ana­log)”.
• When an HDMI IN is assigned to an input selector in “HDMI Input Setup” on page 50, this input assign­ment is automatically set to the same HDMI IN. And in addition to the usual inputs (e.g., COAX1, COAX2, etc.), you can also select HDMI inputs. If you change the input assignment from an HDMI IN to one of the other inputs (e.g., COAX1 or COAX2), be sure to set the “Using the DIGITAL INPUT Button” on page 58 to the same input (e.g., COAX1 or COAX2).
• “AUX2” is used only for digital input from the front panel terminals. When HDMI IN is assigned to “AUX2” in the “HDMI Input Setup” on page 50, the same HDMI IN can be selected.
Examples:
If you connect your DVD player to the OPTICAL IN 1 jack, set “DVD” to “OPT1”. If you want to listen to audio from the component connected to the OPTICAL IN 2 jack when the VCR/DVR input selector is selected, set “VCR/DVR” to “OPT2”. If you want to listen to audio from the component connected to the COAX­IAL IN 1 jack when the CBL/SAT input selector is selected, set “CBL/SAT” to “COAX1”. For input selectors that you don’t want
to assign a digital input jack, set to “- - - (analog)”.
Press the [SETUP] button.
Setup closes.
3
Use the Up and Down [q]/[w] but­tons to select “4. Digital Audio Input”, and then press [ENTER].
The “Digital Audio Input” menu appears.
1–4. Digital Audio Input DVD VCR/DVR CBL/SAT GAME/TV AUX
AUX2
TAPE
TUNER
CD PHONO
MOVE VALUE RETURN
RETURN
COAX1 COAX2 COAX3
OPT1
- - -
FRONT
- - -
- - -
OPT2
- - -
SETUP
EXIT
Notes:
• Only FRONT can be assigned to the AUX 2 input selector.
• This procedure can also be performed on the AV con­troller by using its [SETUP] button, arrow buttons, and [ENTER] button.
53
Page 54
First Time Setup—Continued
6

Analog Audio Input Setup

1
2, 3
2–
1, 7
If you connect a component to the AV controller’s analog multichannel input, you must assign that input to an input selector. For example, if you connect your DVD player to the MULTI CH input, you must assign it to the DVD input selector.
If you connect a component to the AV controller’s bal­anced input, you must assign that input to an input selector. For example, if you connect your CD player to the BALANCED input, you must assign it to the CD input selector.
1
2
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen.
Use the Up and Down [q]/[w] but­tons to select “1. Input/Output Assign”, and then press [ENTER].
The “Input/Output Assign” menu appears.
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
3
4
5
6
7
Notes:
• To listen to the component connected to the multi­channel input, press the [AUDIO SEL] button repeat­edly to select Multich (see page 114).
• This procedure can also be performed on the AV con­troller by using its [SETUP] button, arrow buttons, and [ENTER] button.
Use the Up and Down [q]/[w] but­tons to select “5. Analog Audio Input”, and then press [ENTER].
The “Analog Audio Input” menu appears.
1–5. Analog Audio Input Multich Balance Balance Input
VALUE RETURN
Use the Left and Right [e]/[r] buttons to select an input selec­tor.
You can assign the multichannel input to the following input selectors: “DVD”, “VCR/DVR”, “CBL/SAT”, “GAME/TV”, “AUX1”, “AUX2”, “TAPE”, “CD”, or “PHONO”.
Use the Up and Down [q]/[w] but­tons to select “Balance”, and use
the Left and Right [e]/[r] but­tons to select an input selector:
You can assign the balanced input to the following input selectors: DVD, “DVD”, “VCR/DVR”, “CBL/SAT”, “GAME/TV”, “AUX1”, “AUX2”, “TAPE”, “CD”, or “PHONO”.
Use the Up and Down [q]/[w] but­tons to select “Balance Input”, and use the Left and Right
[e]/[r] buttons to select:
Stereo:
Select if the source is stereo and you’ve connected it to the BAL­ANCED L and R INPUT XLR jacks.
Mono:
Select if the source is mono and you’ve connected it to the BAL­ANCED L INPUT XLR jack.
Press the [SETUP] button.
Setup closes.
RETURN
DVD
SETUP
EXIT
54
Page 55
First Time Setup—Continued
4

Speaker Settings

If you change these settings, you must run the auto­matic speaker setup again (see page 58).
1
2, 3
2–
1, 5
To use bi-amping, you must change the “Speaker Type” setting. For hookup information, see page 25.
Notes:
• When bi-amping is used, the AV controller is able to drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the vol­ume.
The onscreen menus shown in this manual may be slightly different from what you see on your TV.
3
4
5
Use the Up and Down [q]/[w] but­tons to select “1. Speaker Set­tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
2–1. Speaker Settings
Speaker Type Normal
RETURN
MOVE VALUE RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “Speaker Type”, and use the Left and Right
[e]/[r] buttons to select:
Normal:
Select this if you’ve connected your front speakers normally.
Bi-Amp:
Select this if you’ve connected your front speakers for bi-amped opera­tion.
Press the [SETUP] button.
Setup closes.
1
2
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] but­tons to select “2. Speaker Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, and [ENTER] button.
55
Page 56
First Time Setup—Continued

TV Format Setup (not North American models)

For the onscreen setup menus to display properly, you must specify the TV system used in your area.
1
2
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] but­tons to select “6. Miscella­neous”, and then press [ENTER].
The “Miscellaneous” menu appears.
6. Miscellaneous
1. Volume Setup
2. OSD Setup
3. 12V Trigger A Setup
4. 12V Trigger B Setup
5. 12V Trigger C Setup
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
4
Use the Up and Down [q]/[w] but­tons to select “TV Format”, and then use the Left and Right
[e]/[r] buttons to select:
Auto: Select this to have the AV
controller automatically detect the TV system from the video input signals.
NTSC: Select if the TV system in
your area is NTSC.
PAL : Select if the TV system in
your area is PAL.
5
Press the [SETUP] button.
Setup closes.
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, and [ENTER] button.
3
Use the Up and Down [q]/[w] but­tons to select “2. OSD Setup”, and then press [ENTER].
The “OSD Setup” menu appears.
6–2. OSD Setup Immediate Display Monitor Type Display Position TV Format Language
MOVE VALUE RETURN
RETURN
On
16 : 9
Bottom
Auto
English
SETUP
EXIT
Note:
The “TV Format” (*) setting is not available on the North American mod­els.
56
Page 57
First Time Setup—Continued

AM Frequency Step Setup (on some models)

For AM tuning to work properly, you must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted.
1
2
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen.
Use the Up and Down [q]/[w] but­tons to select “7. Hardware Setup”, and then press [ENTER].
The “Hardware Setup” menu appears.
7. Hardware Setup
1. Remote Control
2. Zone2/Zone3
3. Tuner
4. Analog Multich
5. HDMI
6. Network
5
Press the [SETUP] button.
Setup closes.
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, and [ENTER] button.

Changing the Input Display

If you connect an u-capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TAPE IN/OUT jacks, or connect an RI Dock to the AUX 1 jacks, for u to work properly, you must change this setting.
This setting can only be changed on the AV controller.
1, 2 1, 2
3
4
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “3. Tuner”, and then press [ENTER].
The “Tuner” menu appears.
7–3. Tuner
AM Freq Step 9kHz
RETURN
VALUE RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “AM Freq Step”, and then use the Left and Right
[e]/[r] buttons to select:
10kHz: Select if 10 kHz steps are
used in your area.
9kHz: Select if 9 kHz steps are used
in your area.
1
or
2
(3 seconds)
or
(3 seconds)
Press the [TAPE] or [AUX 1] input selector button so that “TAPE” or “AUX1” appears on the display.
Press and hold down the [TAPE] or [AUX 1] input selector button (about 3 seconds) to change the setting.
Repeat this step to select MD, CDR, or DOCK.
For the TAPE input selector, the setting changes in this order:
TA PE MD CDR
DOCK
For the AUX 1 input selector, the set­ting changes in this order: AUX1
DOCK
Note:
DOCK can be selected for the TAPE input selector or AUX 1 input selector, but not both at the same time.
57
Page 58
First Time Setup—Continued
Using the DIGITAL INPUT Button
Digital inputs can also be assigned to input selectors by using the [DIGITAL INPUT] button on the AV controller.
1
2, 3
1
2
3
Press the input selector button for the input selector that you want to assign.
Press the [DIGITAL INPUT] but­ton.
The current assignment is displayed.
Press the [DIGITAL INPUT] but­ton repeatedly to select an option.
Available options are the same as for the Digital Input menu. See step 4 on page 53.
Automatic Speaker Setup
®
(Audyssey MultEQ
With the supplied calibrated microphone, Audyssey MultEQ XT automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position.
Audyssey MultEQ caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Enabling Audyssey MultEQ allows you to also use Audyssey Dynamic EQ™, which maintains the proper octave-to-octave balance at any volume level.
Before using this function, connect and position all of your speakers.
About Audyssey Dynamic Volume
Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same whether watching movies, flipping between television channels, or changing from stereo to surround sound content.
About Audyssey Dynamic EQ
Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ to provide well­balanced sound for every listener at any volume level.
XT
XT)
then removes the distortion
XT
58
Page 59
First Time Setup—Continued
Measurement Positions
To create a listening environment in your home theater that all listeners will enjoy, Audysssey MultEQ measurements at up to eight positions within the lis­tening area.
1st measurement position
This is the center position of your listening area, or the listening position if there’s only one listener.
2nd–8th measurement positions
These are the other listening positions (i.e., the places where the other listeners will sit). You can measure up to eight positions.
The following examples show some typical home theater seating arrangements. Choose the one that best matches yours, and position the microphone accordingly when prompted.
TV TV TV
TVTVTV
®
takes
Using Audyssey MultEQ® XT
1
2, 11
3–10
TV TV TV
: listening area : listening position
Notes:
• If the AV controller is muted, it will be unmuted automatically when the automatic speaker setup starts.
• Automatic speaker setup cannot be performed while a pair of headphones is connected.
• It takes about 15 minutes to complete the auto­matic speaker setup for three positions. Total mea­surement time varies depending on the number of positions and speakers.
• Do not disconnect the speaker setup microphone during the automatic speaker setup, unless you want to cancel the setup.
• Do not connect or disconnect any speakers during the automatic speaker setup.
59
Page 60
First Time Setup—Continued
The onscreen menus shown in this manual may be slightly different from what you see on your TV.
1
Turn on the AV controller and the connected TV.
On the TV, select the input to which the AV controller is connected.
2
Place the speaker setup micro­phone at measurement point 1 (page 59), and connect it to the
SETUP MIC jack.
Auto Speaker Setup
Next
1
Please place microphone at center of listening area at ear height.
ENTER
ENTER
Notes:
Before starting Audyssey MultEQ® XT
• Automatic Speaker Setup, arrange the room and connect the speakers as you would for enjoying movies. Changes to the room after auto setup requires you run the auto setup again, as room EQ characteristics may have changed.
• When starting the automatic speaker setup, do not stand between the speakers and microphone, and avoid obstacles blocking the path between speakers and microphone. This will produce inaccurate results.
• Position the microphone at ear height of a seated listener with the micro­phone tip pointed directly at the ceil­ing using a tripod. Do not hold the microphone in your hand during measurements as this will produce innacurate results.
• Make the room as quiet as possible. Background noise can disrupt the room measurements. Close win­dows, silence cell phones, televi­sions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices.
• Cell phones should be turned off or placed away from all audio electron­ics during the measurement process as Radio Frequency Interference (RFI) may cause measurement dis­ruptions (even if the cell phone is not in use).
3
Press [ENTER].
The automatic speaker setup starts.
Auto Speaker Setup
Do not unplug Setup Mic. Please keep quiet. Now measuring. . .
2
Test tones are played through each speaker as Audyssey MultEQ
®
XT Automatic Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone.
4
The speaker detect results appear.
Auto Speaker Setup
Next Retry Cancel
:Yes :No
Speaker Detect Result
ENTER
MOVE
ENTER
“Yes” means that the speaker was detected. “No” means that no speaker was detected.
If you agree with the results, use the Up and Down [q]/[w] buttons
to select “Next”, and then press [ENTER].
The options are:
Next: Proceed to the next step.
Retry: Return to step 2 and try again.
Cancel: Cancel the automatic speaker
setup.
5
The following screen appears.
Auto Speaker Setup
Next
2
Please place microphone at next position at ear height.
ENTER
ENTER
Place the setup microphone at the next position (see page 59), and then press [ENTER].
Audyssey MultEQ® XT performs more measurements. This takes a few minutes.
Auto Speaker Setup
Do not unplug Setup Mic. Please keep quiet. Now measuring. . .
2
60
Page 61
First Time Setup—Continued
6
7
When prompted, place the setup microphone at the next position, and repeat step 5.
After the 3rd or 7th measure­ment, the following screen appears.
Auto Speaker Setup
Next Finish(Calculate )
Select [Next] to measure the next position, or select [Finish] to calculate the Audyssey MultEQ room EQ solution.
MOVE
ENTER
ENTER
Use the Up and Down [q]/[w] but­tons to select an option, and then press [ENTER].
Next:
Select “Next” to begin measuring the next measurement position. After the 8th measurement has been taken, the procedure automatically proceeds to step 8.
Finish(Calculate):
Select this if you don’t want to measure any more listening posi­tions and are ready to calculate the results, then go to step 8.
10
Use the Up and Down [q]/[w] but­tons to select an option, and then press [ENTER].
Save:
Save the calculated settings and exit the automatic speaker setup.
Review SP Config:
Review the speaker configuration settings (see “Reviewing the Results” on page 63).
Review SP Distance:
Review the speaker distance set­tings (see “Reviewing the Results” on page 63).
Review SP Level:
Review the speaker level settings (see “Reviewing the Results” on page 63).
Cancel:
Cancel the automatic speaker setup.
If you selected “Save”, the results are saved, and the following screen appears.
Auto Speaker Setup
Saving...
8
9
When the measurements are complete, the following screen appears.
Auto Speaker Setup
Calculating...
When the calculations are com­plete, the following screen appears.
Auto Speaker Setup
Save Review SP Config Review SP Distance Review SP Level Cancel
ENTER
MOVE
ENTER
11
Disconnect the setup MIC.
Auto Speaker Setup
Please, unplug Setup Mic.
Notes:
• When the automatic speaker setup is complete, the “Equalizer Settings” (page 95) will be set to
Audyssey.
• You can cancel the automatic speaker setup at any point in the procedure simply by disconnecting the setup microphone.
61
Page 62
First Time Setup—Continued
Error Messages
While the automatic speaker setup is in progress, one of the following error messages may appear:
Ambient noise is too high
Auto Speaker Setup
Retry Cancel
Ambient noise is too high.
!
MOVE
This message appears if the background noise is too loud and the measurements cannot be performed properly.
Remove the source of the noise and try again.
Retry: Return to the measured point immediately
before and start set up again.
Cancel: Cancel the automatic speaker setup.
Speaker Detect Error
Next Cancel
:Yes
!
MOVE
This message appears if a speaker is not detected. “Yes” means that a speaker was detected. “No” means that no speaker was detected. Check your speaker connections and retry, or cancel the automatic speaker setup.
Next Cancel
:Yes
!
MOVE
The front right speaker has not been detected.
ENTER
ENTER
Auto Speaker Setup
:No
!
:---
:Error
Speaker Detect Error
ENTER
ENTER
Auto Speaker Setup
:No
!
:---
:Error
Speaker Detect Error
ENTER
ENTER
Auto Speaker Setup
Next Cancel
:Yes
:No
!
:---
:Error
Speaker Detect Error
!
MOVE
ENTER
ENTER
The surround back left speaker has not been detected.
Auto Speaker Setup
Next Cancel
:Yes
:---
!
MOVE
:No
!
:Error
Speaker Detect Error
ENTER
!
ENTER
There is a problem with the front left speaker. If the warning triangle ( ) appears for the subwoofer, it may be that the output from the subwoofer is too loud.
Auto Speaker Setup
Retry Cancel
Speaker Detect Error
!
MOVE
ENTER
ENTER
The number of speakers detected on the second or third measurement was different to the number detected on the first measurement.
Make sure speakers that cannot be detected are con­nected property.
Retry: Return to step 2 and try again.
Cancel: Cancel the automatic speaker setup.
Writing Error!
Auto Speaker Setup
Retry Cancel
Auto Speaker Setup
Next Cancel
:Yes
:No
!
:---
:Error
Speaker Detect Error
!
MOVE
ENTER
ENTER
The surround right speaker has not been detected.
62
MOVE
Writing Error!
ENTER
ENTER
!
This message appears if saving fails.
Try saving again. If this message appears after 2 or 3 attempts, the AV controller is probably malfunctioning. Contact your Onkyo dealer.
Retry: Return to step 2 and try again.
Cancel: Cancel the automatic speaker setup.
Page 63
First Time Setup—Continued
Reviewing the Results Changing the Speaker Settings Manually
In rare situations, proper measurements taken may not
Use the Up and Down [q]/[w] but­tons to select the settings that you want to review, and then press [ENTER].
Auto Speaker Setup
Save Review SP Config Review SP Distance Review SP Level Cancel
ENTER
MOVE
ENTER
The options are:
Review SP Config
Review the speaker configuration settings.
Auto Speaker Setup
Review SP Config
Subwoofer Front Center Surround Surr Back Surr Back Ch
Yes
Full Band
80Hz 100Hz 150Hz
2ch
RETURN
RETURN
Review SP Distance
Review the speaker distance set­tings.
Auto Speaker Setup
Review SP Distance
Left Center Rightr Surr Right SurrBack Surr Left Subwoofer
15.0ft
15.0ft
15.0ft
7.0ft
7.0ft
7.0ft
15.0ft
RETURN
RETURN
be obtainable by the by the automatic speaker setup. For example, there may be too much noise in the room. If running the speaker setup a second time is still unsuc­cessful you will have to set the speaker settings manu­ally. (see pages 89–95).
Notes:
• For THX-certified speakers, the 80 Hz (THX) cross­over frequency is recommended. If you use the auto­matic speaker setup, you’ll need to manually select 80 Hz (THX) for each THX-certified speaker (see page 89).
• Because of the complexities of low-frequency sounds and the way they interact with a room, THX recom­mends setting the subwoofer level and distance manu­ally.
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by the automatic speaker setup.
If the “Subwoofer” appears on the “Review SP Config” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running the automatic speaker setup again. Note that if the volume is set too high and the sound dis­torts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter
switch, set it to Off or Direct. Refer to your subwoofer’s
instruction manual for details.
Review SP Level
Review the speaker level settings.
Auto Speaker Setup
Review SP Level
Left Center Rightr Surr Right SurrBack Surr Left Subwoofer
+12.0dB
0.0dB
-12.0dB +3.0dB +4.0dB
-3.0dB
0.0dB
RETURN
RETURN
Press [RETURN] to return to the pre­vious screen.
63
Page 64

Basic Operations

R
R

Selecting the Input Source

1
AV controller
emote
controller
3
1
1
3
1
Use the AV controller’s input selector buttons to select an input source.
To select an input source with the remote controller, press its [RECEIVER] REMOTE MODE button, and then use its INPUT SELECTOR buttons.
64
2
3
AV controller
4
emote
controller
Start playback on the source component.
When you select DVD or another video component, on your TV, you’ll need to select the video input that’s connected to the AV controller’s COMPONENT VIDEO MON­ITOR OUT 1 or COMPONENT VIDEO MONITOR OUT 2/ZONE 2 OUT, HDMI OUT MAIN, HDMI OUT SUB, or MONITOR OUT. On some DVD players, you may need to turn on the digital audio output.
To adjust the volume, use the MASTER VOLUME control, or the remote controller’s VOL [q]/[w] button.
The volume can be set to The AV controller is designed for home theater enjoyment. It has a wide volume range,
allowing precise adjustment. The volume level can also be displayed as an absolute value. See “Volume Setup” on
page 108.
Select a listening mode and enjoy!
See “Using the Listening Modes” on page 75.
dB, 81.5 dB through +18.0 dB (relative display).
Page 65
Basic Operations—Continued
This section explains functions that can be used with any input source.
Press [RECEIVER] first
DIMMER
DISPLAY
CH SEL
SLEEP
MUTING
LEVEL – +

Adjusting Speaker Levels

You can adjust the volume of each speaker while listen­ing to an input source. These temporary adjustments are cancelled when the AV controller is set to Standby.
Use the remote controller’s [CH SEL] button to select each speaker, and use the [LEVEL–] and [LEVEL+] buttons to adjust the volume.
You can adjust the volume of each speaker from –12 dB to +12 dB (–15 dB to +12 dB for the subwoofer).
Notes:
• You cannot use this function while the AV controller is muted.
• Speakers that are set to “No” or “None” in the “Speaker Config” cannot be adjusted (see page 89).
Headphones
While a pair of headphones is connected, you can use the [CH SEL], [LEVEL–], and [LEVEL+] buttons to adjust the volume of each headphone speaker (left and right), from –12 dB to +12 dB each.
PHONES DIMMER DISPLAY

Setting the Display Brightness

You can adjust the brightness of the display.
Remote
controller
AV controller
Press the remote controller’s [DIMMER] button repeatedly to select:
• Normal + VOLUME light on.
• Normal + VOLUME light off.
• Dim + VOLUME light off.
• Dimmer + VOLUME light off. You can also use the AV controller’s
[DIMMER] button (not European mod­els).
These settings are stored when the AV controller is set to Standby.

Muting the AV Controller

You can temporarily mute the output of the AV controller.
Press the remote controller’s [MUTING] button.
The output is muted and the MUTING indicator flashes on the display, as shown.
To unmute the AV controller, press the [MUTING] button again, or adjust the volume.
The Mute function is cancelled when the AV controller is set to Standby.
Tip:
You can specify how much the output is muted with the “Muting Level” setting (see page 108).
65
Page 66
Basic Operations—Continued

Using the Sleep Timer

With the sleep timer, you can set the AV controller to turn off automatically after a specified period.
Press the [RECEIVER] button, and then press the [SLEEP] but­ton repeatedly to select the required sleep time.
The sleep time can be set from 90 to 10 minutes in 10 minute steps.
The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears.
If you need to cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the AV controller sleeps,
SLEEP
press the [ [
SLEEP
] button while the sleep time is being displayed,
you’ll shorten the sleep time by 10 minutes.
] button. Note that if you press the

Using Headphones

For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV controller’s PHONES jack.

Adjusting the Bass & Treble

You can adjust the bass and treble for the front speakers, except when the Direct, Pure Audio or THX listening mode is selected.
1
2
Bass
You can boost or cut low-frequency sounds output by the front speakers from –10 dB to +10 dB in 1 dB steps.
Treble
You can boost or cut high-frequency sounds output by the front speakers from –10 dB to +10dB in 1dB steps.
Notes:
• This setting is not available when the multichannel Analog input is selected.
• The tone control settings do not apply to the Direct, Pure Audio, or THX listening modes.
Press the AV controller’s [TONE] button repeatedly to select Bass or Treble for Front, Center, Sur­round, SurrBack, or Subwoofer.
Use the Up [r] and Down [e] buttons to adjust.

Displaying Source Information

You can display various information about the current input source as follows.
Notes:
• Always turn down the volume before connecting your headphones.
• While the headphones plug is inserted in the PHONES jack, the speakers are turned off and the Headphone indicator lights up.
• When you connect a pair of headphones, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, Direct, or Pure Audio.
• Only the Stereo, Direct, Pure Audio, and Mono listen­ing modes can be used with headphones (the listening modes available also depend on the currently selected input source).
• When the multichannel input is used, only the front left and right audio can be heard in the headphones.
66
Remote
controller
AV controller
The following information can typically be displayed:
Input source
Listening
Signal format*
Sampling
frequency
* If the input signal is analog, no format information is displayed.
If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format and the number of channels is displayed. For some digital input sig­nals, including multichannel PCM, the signal format, number of channels, and sampling frequency is displayed. Information is displayed for about three seconds, then the previ­ously displayed information reappears.
Press the [DISPLAY] button repeatedly to cycle through the available information.
mode
Page 67

Listening to the Radio

Listening to AM/FM Stations

TUNING MODE
TUNING
TUNER
With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection.
Use the [TUNER] input selector button to select AM or FM.
In this example, FM has been selected.
Band Frequency
(Actual display depends on country.)
Manual Tuning Mode
1
2
The North American model changes FM frequency in
0.2 MHz steps, 10 kHz steps for AM. For other models it’s 0.05 MHz steps for FM and 9 kHz steps for AM. In Manual Tuning mode, FM stations will be in mono.
Tuning into Weak FM Stereo Stations
If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Press the [TUNING MODE] but­ton so that the AUTO indicator disappears from the display.
Press and hold the TUNING Up or Down [q]/[w] button.
The frequency stops changing when you release the button.
Press the button repeatedly to change the frequency one step at a time.
Tuning into AM/FM Radio Stations
Auto Tuning Mode
1
2
When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears. (The FM STEREO indicator will not appear on models that have HD Radio reception.)
Press the [TUNING MODE] but­ton so that the AUTO indicator appears on the display.
Press the TUNING Up or Down [q]/[w] button.
Searching stops when a station is found.
TUNED
AUTO
FM STEREO
67
Page 68
Listening to the Radio—Continued
Tuning into Stations by Frequency
You can tune into AM and FM stations directly by enter­ing the appropriate frequency.
Number
buttons
D.TUN
RECEIVER
1
2
Press the [RECEIVER] button, followed by the [D.TUN] button.
The [RECEIVER] button flashes.
(Actual display depends on country.)
Within 8 seconds, use the num­ber buttons to enter the fre­quency of the radio station.
For example, to tune to 87.5 (FM), press 8, 7, 5.
Displaying AM/FM Radio Information
DISPLAY
Press the [DISPLAY] button to display the available information.
Band
Note:
When you select a preset with a custom name (see page 103), its name is displayed instead of the band and frequency.
Frequency Preset #
Listening mode
68
Note:
While the [RECEIVER] button is flash­ing, you cannot select another input source with the remote controller.
Page 69
Listening to the Radio—Continued

Presetting AM/FM Stations

2, 4
You can store a combination of up to 40 of your favorite AM and FM radio stations.
1
2
3
Tune into the AM or FM station you want to store as a preset.
Press the [MEMORY] button.
The preset number flashes.
While the preset number is flash­ing (about 8 seconds), use the
PRESET [e]/[r] buttons to select a preset from 1 through 40.
3
Selecting Presets
PRESET
CH +/–
To select a preset, use the PRE­SET [e]/[r] buttons or the
remote controller’s CH [+/–] but­ton.
4
Note:
You can name your radio presets for easy identification (see page 103).
Press the [MEMORY] button again to store the station.
The station is stored and the preset number stops flashing.
Repeat this procedure for all of your favorite stations.
Deleting Presets
1
2
Select the preset that you want to delete.
See the previous section.
While holding down the [MEM­ORY] button, press the [TUNING MODE] button.
The preset is deleted and its number disappears from the display.
2
69
Page 70
Listening to the Radio—Continued

Listening to HD Radio™ Stations (North American model only)

HD Radio technology brings digital radio to conven­tional analog AM and FM radio stations, with improved sound quality, better reception, and new data services. HD Radio technology provides CD-quality sound for FM stations and FM-quality sound for AM stations. In addition, FM HD Radio stations can transmit multiple programs on the same frequency by using multicast channels. Text data display incudes station name, song title, artist name, and so on.
For more information about HD Radio technology, visit: www.ibiquity.com www.hdradio.com
About HD Radio Stations
HD Radio stations broadcast on the same AM and FM frequencies they’ve always used, and you can receive them by tuning into your favorite station as normal (see page 67). You can store them as presets just like AM and FM stations (see page 69). If the current AM or FM station supports HD Radio tech­nology, the HD indicator lights up. While a digital HD Radio transmission is being received, the DIGITAL indicator lights up. While an analog HD Radio transmission is being received, the ANALOG indicator lights up.
ENTER
DISPLAY
AUDIO SEL
AUDIO SEL
,
Station name
Artist nameSong title
• If the current AM or FM station supports HD Radio technology, the station’s name will be displayed instead of the band and frequency.
• When music data is received, song title and artist name information is displayed.
• If the current HD Radio station supports multicast channels, the name of the currently selected multicast channel will be displayed.
HD Radio channel number
HD indicator
ENTER DISPLAY
70
Page 71
Listening to the Radio—Continued
Selecting Multicast Channels
FM HD Radio stations can transmit multiple programs on the same frequency by using what are called multicast channels. If the current HD Radio station is broadcasting multicast channels, the SPS (secondary program ser­vices) indicator lights up.
1
2
Press [ENTER].
The SPS indicator flashes.
Use the Up and Down Arrow [q]/[w] buttons to select a multi-
cast channel.
If you select a multicast channel that is not currently broadcasting, a plus [+] symbol will appear, indicating that the channel has been reserved. When broadcasting commences, that channel will be selected automatically.
Note:
Multicast channels 2 through 8 only carry a digital sig­nal, so to select an audio format, you must select multi­cast channel #1 first.
Displaying HD Radio Information
Press the [DISPLAY] button repeatedly to cycle through the available information.
Frequency
Station information
Artist information
Song title information
Reserved channel indication
HD Radio channel number
Within 5 seconds, press [ENTER] to set the multicast channel.
Note:
Multicast channels are not available on AM.
Selecting the Audio Format (Blend Mode)
HD Radio stations transmit both analog and digital ver­sions of their programs and you can choose which one you want to listen to.
Remote
controller
AV controller
Use the [AUDIO SEL] button to select “Auto” or “Analog”.
Auto: Select to use the digital sig-
nal.
Analog: Select to use the analog sig-
nal.
71
Page 72
Listening to the Radio—Continued

Using RDS

RDS only works in areas where RDS broadcasts are available. When tuned to an RDS station, the RDS indi­cator appears.
RDS indicator
What is RDS?
RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is avail­able in most European countries. RDS is approved by the National Radio Systems Committee (NRSC) and is available in North America. Many FM stations use it these days. In addition to dis­playing text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.). The AV controller supports four types of RDS informa­tion:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Press­ing the [DISPLAY] button will display the frequency for 3 seconds.
RT (Radio Text)
When tuned to an RDS station that’s broadcasting text information, the text will be shown on the display (see page 73).
PTY (Program Type)
This allows you to search RDS radio stations by type (see page 73).
TP (Traffic Program)
This allows you to search for RDS radio stations that broadcast traffic information (see page 73).
Notes:
• In some cases, the characters displayed on the AV con­troller may not be identical to those broadcast by the radio station. Also, unexpected characters may be dis­played when unsupported characters are received. This is not a malfunction.
• If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.
RDS Program Types (PTY)
Typ e Displ ay
None NONE
News reports NEWS
Current affairs AFFAIRS
Information INFO
Sport SPORT
Education EDUCATE
Drama DRAMA
Culture CULTURE
Science and technology SCIENCE
Var ied VAR IED
Pop music POP M
Rock music ROCK M
Middle of the road music EASY M
Light classics LIGHT M
Serious classics CLASSICS
Other music OTHER M
Weather WEATHER
Finance FINANCE
Children’s programmes CHILDREN
Social affairs SOCIAL
Religion RELIGION
Phone in PHONE IN
Travel TRAVEL
Leisure LEISURE
Jazz music JAZZ
Country music COUNTRY
National music NATION M
Oldies music OLDIES
Folk music FOLK M
Documentary DOCUMENT
Alarm test TEST
Alarm ALARM
72
Page 73
Listening to the Radio—Continued
Displaying Radio Text (RT)
RT/PTY/TP
When tuned to an RDS station that’s broadcasting text information, the text can be displayed.
Press the [RT/PTY/TP] button once.
The RT information scrolls across the display.
Notes:
• The message “Waiting” may appear while the AV con­troller waits for the RT information.
• If the message “No Text Data” appears on the display, no RT information is available.
Finding Stations by Type (PTY)
4
5
Listening to Traffic News (TP)
To start the search, press [ENTER].
The AV controller searches until it finds a station of the type you specified, at which point it stops briefly before con­tinuing with the search.
When a station you want to listen to is found, press [ENTER].
If no stations are found, the message “Not Found” appears.
2 1
3
You can search for stations that broadcast traffic news.
2
3 1
You can search for radio stations by type.
1
2
3
Use the [TUNER] input selector button to select FM.
Press the [RT/PTY/TP] button twice.
The current program type appears on the display.
Use the PRESET [e]/[r] buttons to select the type of program you want.
See the table on page 72.
4, 5
1
2
3
Use the [TUNER] input selector button to select FM.
Press the [RT/PTY/TP] button three times.
If the current radio station is broadcast­ing TP (Traffic Program), “[TP]” will appear on the display and traffic news will be heard as and when it’s broad­cast. If “TP” without square brackets appears, this means that the station is not broadcasting TP.
To locate a station that is broad­casting TP, press [ENTER].
The AV controller searches until it finds a station that’s broadcasting TP. If no stations are found, the message “Not Found” appears.
73
Page 74

Recording

This section explains how to record the input source and how to record audio and video from separate sources.
Notes:
• The surround sound and DSP listening modes cannot be recorded.
• Copy-protected DVDs cannot be recorded.
• Sources connected to the analog multichannel input cannot be recorded.
• Various restrictions apply to digital recording. Refer to the manuals supplied with your digital recording equipment for more details.
• Digital input signals are output by only the digital out­puts, and analog input signals are output by only the analog outputs. There is no internal conversion from digital to analog or vice versa.
• DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.
• While the Pure Audio listening mode is selected, the VCR/DVR OUT V and S jacks don’t output video sig­nals, so select another mode when recording.

Recording the Input Source

Audio sources can be recorded to a recorder (e.g., cas­sette deck, CDR, MD) connected to the TAPE OUT or DIGITAL OPTICAL OUT jacks. Video sources can be recorded to a video recorder (e.g., VCR, DVR) con­nected to the VCR/DVR OUT jacks. See pages 28 to 44 for hookup information.

Recording from Different AV Sources

You can overdub audio onto your video recordings by simultaneously recording audio and video from two sep­arate sources. This is possible because only the audio source is switched when an audio-only input source, such as TAPE, TUNER, or CD, is selected, the video source remains the same. In the following example, audio from the CD player con­nected to the CD IN and video from the camcorder con­nected to the AUX 2 INPUT VIDEO jack are recorded by the VCR connected to the VCR/DVR OUT jacks.
Camcorder
video signal audio signal
1
Use the input selector buttons to select the source that you want to record.
See “Which Connections Should I Use?” on page 29 to see which signals can be output and recorded.
You can watch the source while record­ing it. The AV controller’s MASTER
Remote
controller
DVD
123
GAME/TV
AUX1 AUX
456
TUNER
TAPE
789
PHONO
+10
2
3
VOLUME control has no effect on recording.
CBL/SATVCR/DVR
2
CD
On your recorder, start record­ing.
On the source component, start playback.
Note:
If you select a different input source during recording, that input source will be recorded instead.
CD Player VCR
Prepare the camcorder and CD player for
1
playback.
Prepare the VCR for recording.
2
Press the [AUX 2] input selector button.
3
Press the [CD] input selector button.
4
This selects the CD player as the audio source but leaves the camcorder as the video source.
Start recording on the VCR, then start
5
playback on the camcorder and CD player.
Video from the camcorder and audio from the CD player are recorded by the VCR.
74
Page 75

Using the Listening Modes

Selecting the Listening Modes

For a description of each listening mode, see “About the Listening Modes” on page 82.
• The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV controller with a digital audio connection (coaxial, optical, or HDMI).
• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source Informa­tion” on page 66.
• While a pair of headphones is connected, you can only select the Pure Audio, Mono, Direct, or Stereo listening mode.
Selecting on the AV Controller
STEREO
THX
Selecting with the Remote Controller
SURR
STEREO
PURE A
DIRECT
[STEREO] button
This button selects the Stereo listening mode.
[SURR] button
This button selects the Dolby Digital and DTS listen­ing modes.
LISTENING MODE [e]/[r] buttons
Pressing these buttons repeatedly cycles through all of the listening modes that can be used with the cur­rent input source.
ALL ST
THX
,
PURE AUDIO
[PURE AUDIO] button
This button selects the Pure Audio listening mode. When this mode is selected, the AV controller’s dis­play is turned off and only video signals input through HDMI IN can be output. Pressing this but­ton again will select the previous listening mode.
[STEREO] button
This button selects the Stereo listening mode.
[THX] button
This button selects the THX listening modes.
LISTENING MODE [e]/[r] buttons
Pressing these buttons repeatedly cycles through all of the listening modes that can be used with the cur­rent input source.
LISTENING MODE
[PURE A] button
This button selects the Pure Audio listening mode. When this mode is selected, the AV controller’s dis­play is turned off and only video signals input through HDMI IN can be output.
[DIRECT] button
This button selects the Direct listening mode.
[THX] button
This button selects the THX listening modes.
[ALL ST] button
This button selects the All Channel Stereo listening mode.
75
Page 76
Using the Listening Modes—Continued

Listening Modes Available for Each Source Format

Analog and PCM Sources
Source format
Listening Mode
Pure Audio Direct Stereo Mono Multichannel Neo:6
Neural THX Dolby PLII Movie/
Dolby PLIIx Movie Dolby PLII Music/ Dolby PLIIx Music Dolby PLII Game/ Dolby PLIIx Game
Dolby EX Neo:6 Cinema Neo:6 Music
THX Cinema/Music/Games Dolby PLII/Dolby PLIIx Movie
+ THX Cinema
Dolby PLII/Dolby PLIIx Music
+ THX Music
Dolby PLII/Dolby PLIIx Game
+ THX Games
Neo:6 Cinema/Music
+THX Cinema/Music
Neo:6 + THX Cinema/Music/Game
PLII Game + THX Ultra2 Games
THX Surround EX THX Ultra2
Cinema/Music/Games Neural THX + THX Cinema/Music/Games
MonoMovie
Orchestra
Unplugged
Studio-Mix
TV Logic AllChStereo FullMono
T- D
*5*6
*5*6
*5*6
*5*6
*6
Media
*3
*3
*3
*5
*5
*5
*5
*5*6
Analog/PCM
32–96
kHz
CD, TV, radio, DVD DVD DVD
176.4/
*1
192kHz
✔✔✔✔✔✔✔✔✔ ✔✔✔✔✔✔✔✔✔ ✔✔ ✔✔✔✔✔✔ ✔ ✔✔✔
✔✔
✔✔ ✔✔
*5
*3
*3
*3
✔✔
*5
✔✔✔ ✔ ✔✔✔ ✔ ✔✔✔ ✔ ✔ ✔✔✔ ✔ ✔✔✔ ✔ ✔✔✔ ✔ ✔✔✔
*2
Multi
channel
Analog
Multi
channel
32–96 kHz
✔✔
*4
*7
*4
*4
*4
*4
*4
*4
*4
*4
*7
*1. 32/44.1/48/88.2/96kHz *2. DVD-Audio discs output multichannel 176.4/192 kHz PCM only via HDMI. *3. If there are no surround back speakers, Dolby Pro Logic II is used. *4. Cannot be selected with some source formats. *5. Available only when using surround speakers. *6. PCM of 88.2kHz and 96kHz are processed at 44.1kHz and 48kHz respectively. *7. It is possible to select it by the signal of 32-48kHz.
Multichannel PCM
*1
Mono/Mul
2ch
tiplex
*5*7
*3
*3
*3
*7
✔✔
: Available Listening Modes
Multi
channel
176.4/192 kHz
2ch
*2
Mono/Mul
tiplex
76
: Requires 6.1/7.1 speakers. : Requires 7.1 speakers.
Page 77
Using the Listening Modes—Continued
Dolby Digital, and Dolby Digital Plus Sources
Source format
Listening Mode
Multichannel 2ch Mono/Multiplex Multichannel 2ch Mono/Multiplex
Media
Dolby Digital Dolby Digital Plus
DVD, DTV, etc. Blu-ray, HD DVD
Pure Audio ✔✔✔✔✔✔ Direct ✔✔✔✔✔✔ Stereo ✔✔✔✔✔✔ Mono ✔✔✔✔✔✔
: Available Listening Modes
Neo:6
Neural THX
*3
*4
*3
✔✔
*4
DolbyDigital
DolbyDigital Plus
Dolby PLII Movie/ Dolby PLIIx Movie
Dolby PLII Music/ Dolby PLIIx Music
Dolby PLII Game/ Dolby PLIIx Game
Dolby EX
*3
*2
*2
*2
*3
*3
✔✔
*1
*3
*3
*3
Neo:6 Cinema ✔✔ Neo:6 Music ✔✔
THX Cinema/Music/Games Dolby PLII/Dolby PLIIx Movie
+ THX Cinema
Dolby PLII/Dolby PLIIx Music
+ THX Music
Dolby PLII/Dolby PLIIx Game
+ THX Games
*4
*4
*4
Neo:6 Cinema/Music
+ THX Cinema/Music
Neo:6 + THX Cinema/Music/Game
*4
*4
PLII Game
+ THX Ultra2 Games
THX Surround EX
THX Ultra2 Cinema/Music/Games
Neural THX + THX Cinema/Music/Games
MonoMovie
Orchestra
Unplugged
Studio-Mix
TV Logic
*4
*4
*4
*4
*4
*4
✔✔
*3
*3
*2
*2
*2
*3
*3
*2
*2
*2
✔✔
*3
*3
*3
*3
*3
*3
✔✔✔✔✔✔
✔✔✔✔✔✔
✔✔✔✔✔✔
✔✔✔✔✔✔
✔✔✔✔✔✔
AllChStereo ✔✔✔✔✔✔ FullMono ✔✔✔✔✔✔ T- D ✔✔✔✔✔✔
*1. If there are no surround back speakers, depending on the input signal, Dolby Digital may be used. *2. If there are no surround back speakers, Dolby Pro Logic II is used. *3. Cannot be selected with some source formats. *4. Available only when using surround speakers.
: Requires 6.1/7.1 speakers. : Requires 7.1 speakers.
Note:
With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format changes during playback. It is not a malfunction.
77
Page 78
Using the Listening Modes—Continued
DTS Sources
: Available Listening Modes
Source format
Listening Mode
Multichannel 2ch Mono
Media
DTS, DTS96/24
DVD, CD, etc. DVD, CD, et c.
Pure Audio ✔✔✔✔ Direct ✔✔✔✔ Stereo ✔✔✔✔ Mono ✔✔✔✔ DTS, DTS 96/24
DTS-ES Discrete/Matrix
Neo:6
Neural THX
Dolby PLII Movie/ Dolby PLIIx Movie
Dolby PLII Music/ Dolby PLIIx Music
Dolby PLII Game/ Dolby PLIIx Game
Dolby EX
*2
*2
*2
*3
*5
*3
*3
*4*5
*3
Neo:6 Cinema ✔✔ Neo:6 Music ✔✔
THX Cinema/Music/Games
DTS-ES Discrete/Matrix + THX Cinema/Music/Games
Dolby PLII/Dolby PLIIx Movie
+ THX Cinema/Music
Dolby PLII/Dolby PLIIx Music
+ THX Music
Dolby PLII/Dolby PLIIx Game
+ THX Games
Neo:6 Cinema/Music
*4
*4
+ THX Cinema/Music
Neo:6 + THX Cinema/Music/Game
*4
*4
*4
*4
PLII Game
+ THX Ultra2 Games
THX Surround EX
THX Ultra2 Cinema/Music/Games
Neural THX + THX Cinema/Music/Games
MonoMovie
Orchestra
Unplugged
Studio-Mix
TV Logic
*4 *5
*4*5
*4*5
*4*5
*4*5
*4
*3
*2
*2
*2
*3
*3
*3
*5
*5
✔✔✔✔
✔✔✔✔
✔✔✔✔
✔✔✔✔
✔✔✔✔
AllChStereo ✔✔✔✔ FullMono ✔✔✔✔
T- D
*5
✔✔✔✔
*1. If there are no surround back speakers, DTS is used. *2. If there are no surround back speakers, Dolby Pro Logic II is used. *3. Cannot be selected with some source formats. *4. Available only when using surround speakers. *5. DTS 96/24 is processed as DTS.
DTS-ES
Discrete/Matrix
*1
*1
78
: Requires 6.1/7.1 speakers. : Requires 7.1 speakers.
Page 79
Using the Listening Modes—Continued
TrueHD Sources
: Available Listening Modes
Source format
Listening Mode Pure Audio ✔✔✔✔✔ Direct ✔✔✔✔✔ Stereo ✔✔✔✔✔ Mono ✔✔✔
Tru eH D ✔✔
Neo:6
Neural THX
Dolby PLII Movie/ Dolby PLIIx Movie
Dolby PLII Music/ Dolby PLIIx Music
Dolby PLII Game/ Dolby PLIIx Game
Dolby EX
Neo:6 Cinema Neo:6 Music
THX Cinema/Music/Games Dolby PLII/Dolby PLIIx Movie
+ THX Cinema
Dolby PLII/Dolby PLIIx Music
+ THX Music
Dolby PLII/Dolby PLIIx Game
+ THX Games
Neo:6 Cinema/Music
+ THX Cinema/Music
Neo:6 + THX Cinema/Music/Game
PLII Game
Media
*1
*1
*1
*3
*3
*3
*3
Multichannel 2ch Mono/Multiplex Multichannel 2ch Mono/Multiplex
*2
*4
*2
*2
*2
*3
*2
*2
*2
+ THX Ultra2 Cinema
THX Surround EX
THX Ultra2 Cinema/Music/Games
Neural THX + THX Cinema/Music/Games
MonoMovie
Orchestra
Unplugged
Studio-Mix
TV Logic AllChStereo ✔✔✔ FullMono ✔✔✔ T- D ✔✔✔
*3
*3
*3
*3
*3
*3
*1. If there are no surround back speakers, Dolby Pro Logic II is used. *2. Cannot be selected with some source formats. *3. Available only when using surround speakers. *4. It is possible to select it by the signal of 32-48kHz.
*2
*2
*4
✔✔✔
✔✔✔
✔✔✔
✔✔✔
✔✔✔
TrueHD TrueHD 192kHz
Blu-ray, HD DVD Blu-ray, HD DVD
*3*4
*1
*1
*1
*4
Requires 6.1/7.1 speakers.
:
Requires 7.1 speakers.
:
Note:
With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format changes during playback. It is not a malfunction.
79
Page 80
Using the Listening Modes—Continued
DTS-HD Sources
Source format
Listening Mode
Pure Audio ✔✔✔✔✔✔✔✔ Direct ✔✔✔✔✔✔✔✔ Stereo ✔✔✔✔✔✔✔✔ Mono DTS-HD High Resolution DTS-HD Master Audio ✔✔
Neo:6
Neural THX
Dolby PLII Movie/ Dolby PLIIx Movie Dolby PLII Music/ Dolby PLIIx Music Dolby PLII Game/ Dolby PLIIx Game
Dolby EX
Neo:6 Cinema Neo:6 Music
THX Cinema/Music/Games Dolby PLII/Dolby PLIIx Movie
+ THX Cinema
Dolby PLII/Dolby PLIIx Music
+ THX Music
Dolby PLII/Dolby PLIIx Game
+ THX Games
Neo:6 Cinema/Music
+ THX Cinema/Music
Neo:6 + THX Cinema/Music/Game
PLII Game
Media
*1
*1
*1
*3
*3
*3
*3
+ THX Ultra2 Games
THX Surround EX THX Ultra2
Cinema/Music/Games Neural THX + THX Cinema/Music/Games
MonoMovie
Orchestra
Unplugged
Studio-Mix
TV Logic AllChStereo ✔✔✔✔✔✔ FullMono ✔✔✔✔✔✔ T- D ✔✔✔✔✔✔
*3
*3
*3
*3
*3
DTS-HD High Resolution DTS-HD Master Audio DTS-HD Master Audio 192kHz
Multi
channel
2ch Mono
Blu-ray, HD DVD Blu-ray, HD DVD Blu-ray, HD DVD
✔✔✔
*2
*4
*2
*2
*3*4
*2
✔ ✔
*3
✔✔
*2
*2
*2
*2
*2
*4
*3
✔✔✔✔✔✔
✔✔✔✔✔✔
✔✔✔✔✔✔
✔✔✔✔✔✔
✔✔✔✔✔✔
*1
*1
*1
✔✔
*4
Multi
channel
✔✔✔
*2
*4
*2
*2
*2
*2
*2
*2
*2
*2
*4
2ch Mono
*3*4
*1
*1
*1
*4
: Available Listening Modes
Multi
channel
2ch Mono
*1. If there are no surround back speakers, Dolby Pro Logic II is used. *2. Cannot be selected with some source formats. *3. Available only when using surround speakers. *4. It is possible to select it by the signal of 32-48kHz.
Requires 6.1/7.1 speakers.
:
Requires 7.1 speakers.
:
Note:
With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format changes during playback. It is not a malfunction.
80
Page 81
Using the Listening Modes—Continued
DTS Express and DSD Sources
Source format
Listening Mode Pure Audio ✔✔✔✔✔ Direct ✔✔✔✔✔ Stereo ✔✔✔✔✔ Mono ✔✔✔✔✔ DTS Express DSD Neo:6
Neural THX Dolby PLII Movie/
Dolby PLIIx Movie Dolby PLII Music/ Dolby PLIIx Music Dolby PLII Game/ Dolby PLIIx Game Dolby EX Neo:6 Cinema ✔✔ Neo:6 Music ✔✔
THX Cinema/Music/Games Dolby PLII/Dolby PLIIx Movie
+ THX Cinema
Dolby PLII/Dolby PLIIx Music
+ THX Music
Dolby PLII/Dolby PLIIx Game
+ THX Games
Neo:6 Cinema/Music
+ THX Cinema/Music
Neo:6 + THX Cinema/Music/Game
PLII Game
Media
*2
*2
*2
*4
*4
*4
*4
Multichannel 2ch Mono
*3
*3
*3
*3
*4
✔✔
*3
*3
*3
+ THX Ultra2 Games
THX Surround EX THX Ultra2
Cinema/Music/Games Neural THX + THX Cinema/Music/Games
MonoMovie
Orchestra
Unplugged
Studio-Mix
TV Logic AllChStereo ✔✔✔✔✔ FullMono ✔✔✔✔✔ T- D ✔✔✔✔✔
*4
*4
*4
*4
*4
*4
*3
*3
✔✔ ✔✔
✔✔✔✔✔
✔✔✔✔✔
✔✔✔✔✔
✔✔✔✔✔
✔✔✔✔✔
DTS Express
Blu-ray, HD DVD SACD
*4
✔✔
*2
*2
*2
✔✔
: Available Listening Modes
Multichannel
(3/2.1)
DSD
*1
2ch
*4
*2
*2
*2
*1. DSD sources are converted and handled as PCM. *2. If there are no surround back speakers, Dolby Pro Logic II is used. *3. Cannot be selected with some source formats. *4. Available only when using surround speakers.
Requires 6.1/7.1 speakers.
:
Requires 7.1 speakers.
:
Hint!
If you can select PCM or DSD output on your SACD player, in some cases, selecting PCM will provide the best sound quality.
Note:
With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format changes during playback. It is not a malfunction.
81
Page 82
Using the Listening Modes—Continued

About the Listening Modes

The AV controller’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.
The LISTENING MODE button illustration shows that listening modes can be selected.
Button: The LISTENING MODE button illustration shows
the remote controller buttons with the exception of the [PURE A] button (All buttons with the exception of the [PURE A] button are on both the AV controller and the remote controller).
See “Selecting the Listening Modes” on page 75 for information on the use of the LISTENING MODE buttons.
Pure Audio
Button:
In this mode, the display and video circuitry are turned off, minimizing possible noise sources for the ultimate in high-fidelity reproduction. (As the video circuitry is turned off, only video signals input through HDMI IN can be output.)
Note:
• The Pure Audio listening mode cannot be selected while Zone 2 is on.
Direct
Button: In this mode, audio from the input source is output
directly with minimal processing, providing high-fidel­ity reproduction. All of the source’s audio channels are output as they are.
Stereo
Button: Sound is output by the front left and right speakers and
subwoofer.
Mono
Use this mode when watching an old movie with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.
Multichannel
This mode is for use with analog or PCM multichannel sources.
PURE A
PURE A
PURE AUDIO
DIRECT
STEREO
Dolby Pro Logic IIx
Dolby Pro Logic II
Dolby Pro Logic IIx expands any 2-channel source for
7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging. If you’re not using any surround back speakers, Dolby Pro Logic II will be used instead of Dolby Pro Logic IIx.
• Dolby PLIIx Movie
Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g., TV, DVD, VHS).
• Dolby PLIIx Music
Use this mode with any stereo or Dolby Surround (Pro Logic) music source (e.g., CD, radio, cassette, TV, VHS, DVD).
• Dolby PLIIx Game
Use this mode with video games, especially those that bear the Dolby Pro Logic II logo.
Dolby Digital
Use this mode with DVDs that bear the Dolby Digital logo, and Dolby Digital TV broadcasts. This is the most common digital surround-sound format, and it’ll put you right in the middle of the action, just like being in a movie theater or concert hall.
5.1-channel source + Dolby EX
These modes expand 5.1-channel sources for 6.1/7.1­channel playback. They’re especially suited to Dolby EX soundtracks that include a matrix-encoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects.
Dolby Digital Plus
Developed for use with HDTV, including the new video disc formats Blu-ray and HD DVD, this is the latest mul­tichannel audio format from Dolby. It supports up to 7.1 channels with 48 kHz sampling rate.
82
Page 83
Using the Listening Modes—Continued
Dolby TrueHD
Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc for­mats, this new Dolby format offers up to 7.1 discrete channels of digital audio with 48/96 kHz, up to 5.1-chan­nels with 192 kHz sampling rate.
For the signals supported by the AV controller, see page 79.
5.1-channel source + Dolby PLIIx Music
These modes use the Dolby Pro Logic IIx Music mode to expand 5.1-channel sources for 6.1/7.1-channel playback.
5.1-channel source + Dolby PLIIx Movie
These modes use the Dolby Pro Logic IIx Movie mode to expand 5.1-channel sources for 7.1-channel playback.
DTS
The DTS digital surround-sound format supports up to
5.1 discrete channels and uses less compression for high­fidelity reproduction. Use it with DVDs and CDs that bear the DTS logo.
DTS 96/24
This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.
DTS-ES Discrete
This mode is for use with DTS-ES Discrete soundtracks, which use a discrete surround back channel for true
6.1/7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360­degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Dis­crete soundtrack.
DTS-ES Matrix
This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1­channel playback. Use it with DVDs that bear the DTS­ES logo, especially those with a DTS-ES Matrix soundtrack.
DTS Neo:6
This mode expands any 2-channel source for up to 7.1­channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, provid­ing a very natural and seamless surround sound experi­ence that fully envelops the listener.
•Neo:6 Cinema
Use this mode with any stereo movie (e.g., TV, DVD, VHS).
• Neo:6 Music
Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD).
5.1-channel source + Neo:6
This mode uses Neo:6 to expand 5.1-channel sources for
6.1/7.1-channel playback.
DTS-HD High Resolution Audio
Developed for use with HDTV, including the new video disc formats Blu-ray and HD DVD, this is the latest mul­tichannel audio format from DTS. It supports up to 7.1 channels with 96 kHz sampling rate.
DTS-HD Master Audio
Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc for­mats, this new DTS format offers up to 7.1 discrete chan­nels of digital audio with 48/96 kHz, up to 5.1-channels with 192 kHz sampling rate.
For the signals supported by the AV controller, see page 80.
DTS Express
This format supports up to 5.1 channels and a lower sam­pling rate of 48 kHz. Applications include interactive audio and commentary encoding for HD DVD Sub Audio and Blu-ray Secondary Audio. Also broadcast and media servers.
83
Page 84
Using the Listening Modes—Continued
Neural THX 5.1/7.1
Neural-THX Surround employs psychoacoustic fre­quency domain processing, which allows delivery of a more detailed sound stage, with superior channel separa­tion and localization of audio elements. The Neural THX
5.1 and Neural THX 7.1 modes can expand any 2-chan-
nel stereo source for 5.1- or 7.1-channel playback, respectively. Use them with CD, radio, cassette, TV, VHS, DVD, and other 2-channel stereo sources, includ­ing video games. Neural-THX Surround can also be used by broadcasters to encode and transmit surround­sound content over a stereo signal, which listeners can enjoy as either surround sound or normal stereo. XM Satellite Radio, for example, is using Neural-THX Sur­round on select channels, which the AV controller can expand from 5.1 channels to 7.1 channels.
DSD
DSD stands for Direct Stream Digital and is the format used to store digital audio on Super Audio CDs (SACD). This mode can be used with SACDs that feature multi­channel audio.
THX
Founded by George Lucas, THX develops stringent stan­dards that ensure movies are reproduced in movie the­aters and home theaters just as the director intended.
THX Modes carefully optimize the tonal and spatial characteristics of the soundtrack for reproduction in the home-theater environment. They can be used with 2­channel matrixed and multichannel sources.
Surround back speaker output depends on the source material and the selected listening mode.
•THX Cinema
THX Cinema mode corrects theatrical soundtracks for playback in a home theater environment. In this mode, THX Loudness Plus is configured for cinema levels and Re-EQ, Timbre Matching, and Adaptive Decorrelation are active.
•THX Music
THX Music mode is tailored for listening to music, which is typically mastered at significantly higher levels than movies. In this mode, THX Loudness Plus is configured for music playback and only Tim­bre Matching is active.
•THX Games
THX Games mode is meant for spatially accurate playback of game audio, which is often mixed simi­larly to movies but in a smaller environment. THX Loudness Plus is configured for game audio levels, with Timbre Matching active.
• THX Ultra2 Cinema
This mode expands 5.1-channel sources for 7.1­channel playback. It does this by analyzing the com­position of the surround source, optimizing the ambient and directional sounds to produce the sur­round back channel output.
• THX Ultra2 Music
This mode is designed for use with music. It expands
5.1-channel sources for 7.1-channel playback.
• THX Ultra2 Games
This mode is designed for use with video games. It can expand 5.1-channel sources for 6.1/7.1-channel playback.
• THX Surround EX
This mode expands 5.1-channel sources for 6.1/7.1­channel playback. It’s especially suited to Dolby Digital EX sources. THX Surround EX, also known as Dolby Digital Surround EX, is a joint develop­ment between Dolby Laboratories and THX Ltd.
84
Page 85
Using the Listening Modes—Continued
Onkyo Original DSP Modes
Mono Movie
This mode is suitable for old movies and other mono sources. The center speaker outputs the sound as it is, while reverb is applied to the sound output by the other speakers, giving presence to even mono material.
Orchestra
Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.
Unplugged
Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.
Studio-Mix
Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acous­tic image, like being at a club or rock concert.
TV Logic
This mode adds realistic acoustics to TV shows pro­duced in a TV studio, surround effects to the entire sound, and clarity to voices.
All Ch Stereo
Ideal for background music, this mode fills the entire lis­tening area with stereo sound from the front, surround, and surround back speakers.
Full Mono
In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room.
T-D (Theater-Dimensional)
With this mode you can enjoy a virtual 5.1 surround sound even with only two or three speakers. This works by controlling how sounds reach the listener’s left and right ears. Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.
85
Page 86

Advanced Setup

The onscreen setup menus appear on the connected TV and provide a convenient way to change the AV controller’s various settings. Settings are organized into eight cate­gories on the main menu, most containing a submenu.
The onscreen menus shown in this manual may be slightly different from what you see on your TV.
MENU
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Lock Setup
ENTER
MOVE ENTER RETURN
RETURN
SETUP
EXIT

Menu Map

The following map shows how the setup menus are organized. Use the page numbers to locate information about items.
Main menu Submenu
MENU
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Lock Setup
page 108
6. Miscellaneous
1. Volume Setup
2. OSD Setup
3. 12V Trigger A Setup
4. 12V Trigger B Setup
5. 12V Trigger C Setup
page 110
7. Hardware Setup
1. Remote Control
2. Zone2/Zone3
3. Tuner
4. Analog Multich
5. HDMI
6. Network
page 56
pages 49–54
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
pages 89–97
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
page 98
3. Audio Adjust
1. Tone Control
2. DSD
3. Multiplex/Mono
4. PLIIx/Neo:6
5. Dolby EX
6. Theater-Dimensional
7. LFE Level
pages 102–103
page 55
86
page 113
8. Lock Setup
Lock Unlocked
page 57
4. Source Setup
1. IntelliVolume
2. A/V Sync
3. Name Edit
4. Picture Adjust
5. Satellite Radio
6. SIRIUS Parental Lock
page 107
5. Listening Mode Preset
1. DVD
2. VCR/DVR
3. CBL/SAT
4. GAME/TV
5. AUX1
6. AUX2
7. TAPE
8. TUNER
9. CD
10. PHONO
DVD
Page 87
Advanced Setup—Continued
4

Monitor Out Setup

This section explains items on the “Input/Output Assign” menu.
1
2, 3
2–
1, 5
3
4
5
Use the Up and Down [q]/[w] but­tons to select an item, and then press [ENTER].
The screen for that item appears.
Use the Up and Down [q]/[w] but­tons to select an item, and use the Left and Right [e]/[r] but­tons to change it.
The items are explained below.
When you’ve finished, press the [SETUP] button.
Setup closes.
1
2
Press the [RECEIVER] button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] but­tons to select “1. Input/Output Assign”, and then press [ENTER].
The “Input/Output Assign” menu appears.
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
5. Analog Audio Input
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, zand [ENTER] button.
87
Page 88
Advanced Setup—Continued
Monitor Out
Resolution
You can specify the output resolution for the HDMI out­puts and have the AV controller upconvert the picture resolution as necessary to match the resolution sup­ported by your TV.
Through: Select this to pass video through the AV con-
Auto: Select this to have the AV controller auto-
480p (480/576p):
720p: Select this for 720p output and video con-
1080i: Select this for 1080i output and video con-
1080p: Select this for 1080p output and video con-
Source:
Brightness
With this setting you can adjust the picture brightness. Can be adjusted from –50 to +50 in steps of 1 (default is
0).
“–50” is the darkest. “+50” is the brightest.
Contrast
With this setting you can adjust Contrast. Can be adjusted from –50 to +50 in steps of 1 (default is
0).
“–50” is the least. “+50” is the greatest.
Hue
With this setting you can adjust the red/green balance. Can be adjusted from –20 to +20 in steps of 1 (default is
0).
“–20” is the strongest green. “+20” is the strongest red.
Saturation
With this setting you can adjust saturation. Can be adjusted from –50 to +50 in steps of 1 (default is
0).
“–50” is the weakest color. “+50” is the strongest color.
troller at the same resolution and with no conversion (default).
matically convert video at resolutions not supported by your TV.
(Not available when the “Monitor Out” set­ting is set to “Analog”.)
Select this for 480p or 576p output and video conversion as necessary.
version as necessary.
version as necessary.
version as necessary. (Not available when the “Monitor Out” setting is set to “Analog”.) Output will be according to the resolution level
which was set with Resolution inside Source: 4-4. Picture Adjust. (Setting for each Source becomes possible.)
Gamma
Adjust the balance of incoming picture R (red), G (green), and B (blue) color data signal to the output color data signal.
Can be adjusted from –3 to +3 in steps of 1 (default is 0).
R Brightness
With this setting you can adjust the picture red bright­ness.
Can be adjusted from –50 to +50 in steps of 1 (default is
0). “–50” is the darkest. “+50” is the brightest.
R Contrast
With this setting you can adjust red Contrast. Can be adjusted from –50 to +50 in steps of 1 (default is
0). “–50” is the least.
“+50” is the greatest.
GBrightness
With this setting you can adjust the picture green bright­ness.
Can be adjusted from –50 to +50 in steps of 1 (default is
0). “–50” is the darkest. “+50” is the brightest.
G Contrast
With this setting you can adjust green Contrast. Can be adjusted from –50 to +50 in steps of 1 (default is
0). “–50” is the least.
“+50” is the greatest.
B Brightness
With this setting you can adjust the picture blue bright­ness.
Can be adjusted from –50 to +50 in steps of 1 (default is
0). “–50” is the darkest.
“+50” is the brightest.
B Contrast
With this setting you can adjust blue Contrast. Can be adjusted from –50 to +50 in steps of 1 (default is
0). “–50” is the least.
“+50” is the greatest.
88
Page 89
Advanced Setup—Continued

Speaker Setup

This section explains items on the “Speaker Setup” menu.
Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 58).
1
3-12
2, 13
Speaker Settings
See “Speaker Settings” on page 55.
Speaker Configuration
1
2
3
4
Press the [RECEIVER] REMOTE MODE button.
Press the [SETUP] button.
The main menu appears onscreen.
Use the Up and Down [q]/[w] but­tons to select “2. Speaker Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “2. Speaker Con­fig”, and then press [ENTER].
The “Speaker Config” screen appears.
These settings are set automatically by the Automatic Speaker Setup function (see page 58).
With the Speaker Configuration settings, you can specify which speakers are connected and a crossover frequency, distance, and level for each speaker.
The following crossover frequencies can be specified: Full Band, 40 Hz, 45 Hz, 50 Hz, 55 Hz, 60 Hz, 70 Hz, 80 Hz (THX), 90 Hz, 100 Hz, 110 Hz, 120 Hz, 130 Hz, 150 Hz, or 200 Hz.
Specify Full Band for speakers that can output low-fre­quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre­quency will then be output by the subwoofer instead of the speaker. Refer to your speakers’ manuals to deter­mine the optimum crossover frequencies.
If you’re using THX-certified speakers, specify 80 Hz (THX) for all speakers.
2–2. Speaker Config Subwoofer Front Center Surround SurrBack SurrBack Ch LPF of LFE
DoubleBass
MOVE VA LUE
Yes
Full Band
100Hz 100Hz 100Hz
2ch
120Hz
On
RETURN
Speaker A
RETURN
SETUP
EXIT
89
Page 90
Advanced Setup—Continued
5
6
7
Use the Up and Down [q]/[w] but­tons to select “Subwoofer”, and then use the Left and Right [e]/[r] buttons to select:
Ye s: Select if a subwoofer is con-
nected.
No: Select if no subwoofer is con-
nected.
Use the Up and Down [q]/[w] but­tons to select “Front”, and then use the Left and Right [e]/[r] buttons to select a crossover fre­quency.
Note:
Fixed at “Full Band” if “Subwoofer” (step 5) is set to “No”.
Use the Up and Down [q]/[w] but­tons to select “Center”, and then use the Left and Right [e]/[r] buttons to select a crossover fre­quency.
If no center speaker is connected, select None.
Note:
Cannot select “Full Band” if “Front” (step 6) is set to anything other than “Full Band”.
9
10
Use the Up and Down [q]/[w] but­tons to select “SurrBack”, and then use the Left and Right [e]/[r] buttons to select a cross­over frequency.
If no surround back speakers are con­nected, select “None”.
Notes:
• Cannot be set if “Speaker Type” is set to “Bi-Amp” (page 55), “Sur­round” is set to “None” (step 8).
• Cannot select “Full Band” if “Sur­round” (step 8) is set to anything other than “Full Band”.
Use the Up and Down [q]/[w] but­tons to select “SurrBack Ch”, and then use the Left and Right [e]/[r] buttons to select:
1ch: Select if one surround back
speaker is connected.
2ch: Select if two (left and right)
surround back speakers are connected.
Note:
Cannot be set if “Speaker Type” is set to “Bi-Amp” (page 55), “SurrBack” is set to “None” (step 9).
Continue with step 11 on the next page.
90
8
Use the Up and Down [q]/[w] but­tons to select “Surround”, and then use the Left and Right [e]/[r] buttons to select a cross­over frequency.
If no surround left and right speakers are connected, select “None”.
Note:
Cannot select “Full Band” if “Front” (step 6) is set to anything other than “Full Band”.
Page 91
Advanced Setup—Continued
Low-Pass Filter for the LFE Channel
This setting is not set automatically by the Automatic Speaker Setup function (see page 58).
With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
*If you’re using THX-certified speakers, select “80Hz(THX)”.
11
Use the Up and Down [q]/[w] but­tons to select “LPF of LFE”, and then use the Left and Right [e]/[r] buttons to select a low­pass filter frequency.
The following low-pass filter frequen­cies can be selected: “80Hz(THX)”, “90Hz”, “100Hz”, “110Hz”, or “120Hz”.
Continue with step 12 in the next col­umn.
Double Bass
This setting is not set automatically by the Automatic Speaker Setup function (see page 58).
With this setting, you can boost bass output by feeding front left and right channel bass sounds to the subwoofer.
This setting can only be made if the “Subwoofer” setting in step 4 is set to “Yes”, and the “Front” setting in step 5 is set to “Full Band”.
*
If you’re using THX-certified speakers, select
“Off(THX)”.
12
Use the Up and Down [q]/[w] but­tons to select “DoubleBass”, and then use the Left and Right [e]/[r] buttons to select:
Off(THX):
The subwoofer only outputs the LFE channel.
On:
In addition to LFE channel sounds, the subwoofer outputs front left and right channel bass sounds.
13
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, and [ENTER] button.
Press the [SETUP] button.
Setup closes.
91
Page 92
Advanced Setup—Continued
2
Speaker Distance
These settings are set automatically by the Automatic Speaker Setup function (see page 58).
With the “Speaker Distance” settings, you can specify the distance from each speaker to the listening position.
4-8
3, 9
1
2
Measure and make a note of the distance from each speaker to the listening position.
Press the [RECEIVER] REMOTE MODE button.
5
6
Use the Up and Down [q]/[w] but­tons to select “3. Speaker Dis­tance”, and then press [ENTER].
The “Speaker Distance” screen appears.
2–3. Speaker Distance Unit Left Center Right SurrRight SurrBack R SurrBack L SurrLeft Subwoofer
MOVE VA LUE
feet
12.0ft
12.0ft
12.0ft
12.0ft
12.0ft
12.0ft
12.0ft
12.0ft
RETURN
Speaker A
RETURN
SETUP
EXIT
Note:
Speakers that you set to “No” or “None” in the Speaker Configuration (page 89) cannot be selected.
Use the Up and Down [q]/[w] but­tons to select “Unit”, and then use the Left and Right [e]/[r] buttons to select:
feet: Select if you want to enter
distances in feet. Can be set
from 0.2 to 30 feet in 0.2-foot
steps.
meters: Select if you want to enter
distances in meters. Can be
set from 0.06 to 9 meters in
0.06-meter steps.
92
3
4
Press the [SETUP] button.
The main menu appears onscreen.
Use the Up and Down [q]/[w] but­tons to select “2. Speaker Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Page 93
Advanced Setup—Continued
7
8
9
Use the Up and Down [q]/[w] but­tons to select a speaker, and use the Left and Right [e]/[r] but­tons to specify the distance.
Specify the distance from the speaker to your listening position.
Notes:
• The “Center” distance cannot be set if the “Center” is set to “None” (page 89).
• The “SurrRight” and “SurrLeft” dis­tances cannot be set if the “Sur­round” is set to “None” (page 89).
• The “SurrBack R” and “SurrBack L” distances cannot be set if “Speaker Type” is set to “Bi-Amp” (page 55), “SurrBack” is set to “None” (page 89).
• The “Subwoofer” distance cannot be set if “Subwoofer” is set to “No” (page 90).
Repeat step 7 for each speaker.
Press the [SETUP] button.
Setup closes.
Speaker Level Calibration
These settings are set automatically by the Automatic Speaker Setup function (see page 58).
With the “Level Calibration” settings, you can adjust the level of each speaker while listening to the test tone so that the volume of each speaker is the same at the listen­ing position.
Notes:
• The speakers cannot be calibrated while the output of the AV controller is muted.
• The test tone is output at the standard level for THX, which is 0 dB (absolute volume setting 82). If you nor­mally listen at volume settings below this, be careful because the test tone will be much louder.
1
3-6
2, 7
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, and [ENTER] button.
1
2
Press the [RECEIVER] REMOTE MODE button.
Press the [SETUP] button.
The main menu appears onscreen.
93
Page 94
Advanced Setup—Continued
3
4
Use the Up and Down [q]/[w] but­tons to select “2. Speaker Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “4. Level Calibra­tion”, and then press [ENTER].
The “Level Calibration” screen appears and the pink noise test tone is output by the front left speaker.
2–4. Level Calibration Left Center Right SurrRight SurrBack R SurrBack L SurrLeft Subwoofer
-12.0dB
-12.0dB
-12.0dB
-12.0dB
-12.0dB
-12.0dB
-12.0dB
-15.0dB
Speaker A
6
Repeat step 5 until the volume of the test tone from each speaker is the same.
If you’re using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listen­ing position, measured with C-weight­ing and slow reading.
7
Press the [SETUP] button.
Setup closes.
Notes:
• Speaker levels can also be adjusted by using the dedi­cated buttons on the remote controller. Press the [TEST TONE] button to output the test tone. Use the [CH SEL] button to select each speaker, and use the [LEVEL–] and [LEVEL+] buttons to adjust the level.
• This procedure can also be performed on the AV con­troller by using its [SETUP] button, arrow buttons, and [ENTER] button.
5
RETURN
SETUP
RETURN
MOVE VA LUE
EXIT
Note:
Levels cannot be adjusted for speakers set to “No” or “None” in the Speaker Configuration (page 89).
Use the Up and Down [q]/[w] but­tons to select a speaker, and use the Left and Right [e]/[r] but­tons to adjust the level.
Levels can be adjusted from –12 to +12 dB in 0.5 dB steps (–15 to +12 dB for the subwoofer).
Notes:
• The “Center” level cannot be set if the “Center” is set to “None” (page 89).
• The “SurrRight” and “SurrLeft” lev­els cannot be set if the “Surround” is set to “None” (page 89).
• The “SurrBack R” and “SurrBack L” levels cannot be set if “Speaker Type” is set to “Bi-Amp” (page 55), “SurrBack” is set to “None” (page 89).
• The “Subwoofer” levels cannot be set if “Subwoofer” is set to “No” (page 90).
94
Page 95
Advanced Setup—Continued
Equalizer Settings
These settings are set automatically by the Automatic Speaker Setup function (see page 58).
With the Equalizer settings, you can adjust the tone of speakers individually with a 7-band equalizer. The vol­ume of each speaker can be set on page 93.
2–5. Equalizer Settings 630Hz 1000Hz 1600Hz 2500Hz 4000Hz 6300Hz 10000Hz 16000Hz
MOVE VA LUE
RETURN
RETURN
0dB 0dB 0dB 0dB 0dB 0dB 0dB 0dB
SETUP
EXIT
1
2
3
2-7
1, 8
1
Press the [RECEIVER] REMOTE MODE button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] but­tons to select “2. Speaker Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
ENTER
RETURN
MOVE ENTER RETURN
Use the Up and Down [q]/[w] but­tons to select “5. Equalizer Set­tings”, and then press [ENTER].
The “Equalizer Settings” screen appears.
SETUP
EXIT
4
Use the Left and Right [e]/[r] buttons to set the “Equalizer” option to:
Off: Equalizer off, flat response.
Manual: The equalizer for each
speaker can be set manually.
MultEQ XT
Dynamic EQ
Dynamic Vol(Light)
Dynamic Vol(Heavy)
*1 These setting can be selected after having
performed the Automatic Speaker Setup. As soon as the Automatic Sp eaker Setup is complete, it will automatically be set to Dynamic EQ™.
*1
*1
*1
*1
When “Dynamic EQ” is selected, “MultEQ®XT” and “Dynamic EQ” become available.
When “Dynamic Vol(Light)” or “Dynamic Vol(Heavy)” is selected, “MultEQ XT”, “Dynamic EQ”, and “Dynamic Volume
” become avail-
able. If you selected “Manual”, continue
with the next step. If you selected oth­ers, go to step 8.
2–5. Equalizer Settings Equalizer Channel 25Hz 40Hz 63Hz 100Hz 160Hz 250Hz 400Hz
MOVE VA LUE
RETURN
Manual
Front
RETURN
0dB 0dB 0dB 0dB 0dB 0dB 0dB
SETUP
EXIT
95
Page 96
Advanced Setup—Continued
MultEQ XT
Audyssey MultEQ XT correction is active (see page 58).
Dynamic EQ
“Audyssey MultEQ XT” and “Dynamic EQ” becomes active (see page 58).
Dynamic Vol(Light)
“Audyssey MultEQ XT”, “Dynamic EQ”, and “Dynamic Volume (Light Compression Mode)” becomes active (see page 58).
This setting prevents loud and soft sounds from being much louder and softer respectively than average sounds.
Dynamic Vol(Heavy)
“Audyssey MultEQ XT”, “Dynamic EQ”, and “Dynamic Volume (Heavy Compression Mode)” becomes active.
This setting affects volume the most, causing all sounds to be of equal loudness.
5
Use the Down [w] button to select “Channel”, and then use the Left and Right [e]/[r] buttons to select a speaker.
You can select: “Front”, “Center”, “Sur­round”, “SurrBack”, or “Subwoofer”.
7
Use the Up and Down [q]/[w] but­tons to select “Channel”, and then use the Left and Right [e]/[r] buttons to select another speaker.
Repeat steps 6 and 7 for each speaker.
8
Press the [SETUP] button.
The setup menu closes.
Notes:
• When the listening mode is set to Direct or Pure Audio, no effect will be produced.
• The Equalizer settings have no effect on 176.4/ 192 kHz input signals.
• This procedure can also be performed on the AV con­troller by using its [SETUP] button, arrow buttons, and [ENTER] button.
6
2–5. Equalizer Settings Equalizer Channel 25Hz 40Hz 63Hz 100Hz 160Hz 250Hz 400Hz
MOVE VA LUE
RETURN
Manual
RETURN
Front
0dB 0dB 0dB 0dB 0dB 0dB 0dB
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select a frequency, and then use the Left and Right [e]/[r] buttons to adjust the level at that frequency.
You can select: “25Hz”, “40Hz”, “63Hz”, “100Hz”, “160Hz”, “250Hz”, “400Hz”, “630Hz”, “1000Hz”, “1600Hz”, “2500Hz”, “4000Hz”, “6300Hz”, “10000Hz”, or “16000Hz”. And for the subwoofer, “25Hz”, “40Hz”, “63Hz”, “100Hz”, or “160Hz”.
The volume at each frequency can be adjusted from –6 to +6 dB in 1 dB steps.
Tip:
Low frequencies (e.g., 160Hz) affect bass sounds; high frequencies (e.g., 6300Hz) affect treble sounds.
96
Page 97
Advanced Setup—Continued
THX Audio Setup
These settings are not set automatically by the Auto­matic Speaker Setup function (see page 58).
With the “SurrBack Sp Spacing” setting, you can specify the distance between your surround back speakers.
If you’re using a THX-certified subwoofer, set the “THX Subwoofer” setting to “Yes”. You can then apply THX’s Boundary Gain Compensation (BGC) to compensate the perceived exaggeration of low frequencies for listeners sitting very close to a room boundary (i.e., wall).
You can also set the THX Loudness Plus feature “On” or “Off”. When the “Loudness Plus” is set to “On”, it is possible to enjoy even subtle nuances of audio expres­sion at low volume.
This result is only available when the THX listening mode is selected.
1
2
Press the [RECEIVER] REMOTE MODE button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] but­tons to select “2. Speaker Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
4
5
Use the Up and Down [q]/[w] but­tons to select “SurrBack Sp Spacing”, and use the Left and Right [e]/[r] buttons to specify the distance between your sur­round back speakers:
> 4ft (>1.2m) (Default): Select this if your surround back speakers are more than 4 feet (1.2 m) apart.
< 1ft (< 0.3m): Select this if your sur­round back speakers are between 0 and 1 foot (0–30 cm) apart.
1ft– 4ft (0.3m–1.2m): Select this if your surround back speakers are between 1 and 4 feet (0.3–1.2 m) apart.
Note:
Cannot be set if “SurrBack Ch” is set to “2ch” (page 90), “Speaker Type” is set to “Bi-Amp” (page 55), “SurrBack” is set to “None” (page 90).
Use the Up and Down [q]/[w] but­tons to select “THX Subwoofer”, and use the Left and Right [e]/[r] buttons to select:
No: Select this if you do not have
a THX-certified subwoofer.
Ye s: Select this if you have a THX-
certified subwoofer.
3
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select “6. THX Audio Setup”, and then press [ENTER].
The “THX Audio Setup” screen appears.
2–6. THX Audio Setup SurrBack Sp Spacing THX Subwoofer BGC Loudness Plus
Preserve THX Settings
MOVE VA LUE
RETURN
RETURN
> 4ft
Yes
Off On
- - -
SETUP
EXIT
When “Loudness Plus” is set to “Off”, the “Preserve THX settings” can be selected.
6
Use the Up and Down [q]/[w] but­tons to select “BGC”, and use the Left and Right [e]/[r] but­tons to select:
Off: Select this to turn off BGC. On: Select this to turn on BGC.
Note:
This setting is only available if “THX Subwoofer” is set to “Yes” (step 5).
97
Page 98
Advanced Setup—Continued
7
8
9
Use the Up and Down [q]/[w] but­tons to select “Loudness Plus”, and use the Left and Right [e]/[r] buttons to select:
Off: Select this to turn off Loud-
ness Plus.
On: Select this to turn on Loud-
ness Plus (default). When “Loudness Plus” is set to “Off”, the “Preserve THX settings” selection
will appear under “Loudness Plus” (Step 8).
Use the Up and Down [q]/[w] but­tons to select “Preserve THX set­tings”, and use the Left and Right [e]/[r] buttons to select:
Ye s: When Yes is selected,
Audyssey Dynamic EQ™ /
Audyssey Dynamic Volume
™ will not be active.
No: When No is selected,
Audyssey Dynamic EQ /
Audyssey Dynamic Volume
will be active in THX listen-
ing mode depending on the
setting.
Note:
This setting is only available if “Loud­ness Plus” is set to “Off” (step 7).
Press the [SETUP] button.
The setup menu closes.

Audio Adjust

Here you can set listening mode-related settings and functions.
1
2
3
Press the [RECEIVER] REMOTE MODE button, followed by the [SETUP] button.
The main menu appears onscreen. If the main menu doesn’t appear, make
sure the appropriate external input is selected on your TV.
Use the Up and Down [q]/[w] but­tons to select “3. Audio Adjust”, and then press [ENTER].
The “Audio Adjust” menu appears.
3. Audio Adjust
1. Tone Control
2. DSD
3. Multiplex/Mono
4. PLIIx/Neo:6
5. Dolby EX
6. Theater-Dimensional
7. LFE Level
ENTER
RETURN
MOVE ENTER RETURN
SETUP
EXIT
Use the Up and Down [q]/[w] but­tons to select an item, and then press [ENTER].
The function menu you selected appears.
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, and [ENTER] button.
THX Loudness Plus
THX Loudness Plus is a new volume control tech­nology featured in THX Ultra2 Plus™ and THX Select2 Plus™ Certified receivers. With THX Loud­ness Plus, home theater audiences can now experi­ence the rich details in a surround mix at any volume level. A consequence of turning the volume below Reference Level is that certain sound elements can be lost or perceived differently by the listener. THX Loudness Plus compensates for the tonal and spatial shifts that occur when the volume is reduced by intelligently adjusting ambient surround channel levels and frequency response. This enables users to experience the true impact of soundtracks regardless of the volume setting. THX Loudness Plus is auto­matically applied when listening in any THX listen­ing mode. The new THX Cinema, THX Music, and THX Games modes are tailored to apply the proper THX Loudness Plus settings for each type of con­tent.
98
4
Use the Up and Down [q]/[w] but­tons to select the settings, and use the Left and Right [e]/[r] buttons to set them.
The settings are explained below.
Page 99
Advanced Setup—Continued
5
Note:
This procedure can also be performed on the AV control­ler by using its [SETUP] button, arrow buttons, and [ENTER] button.
When you’ve finished, press the [SETUP] button.
The setup menu closes.
Tone Control Settings
You can adjust the tone (bass and treble) of the front, center, surround, and surr back speakers individually. For the subwoofer, you can adjust the bass.
Bass
You can boost or cut low-frequency sounds from –10 dB to +10 dB in 1 dB steps.
Treble
You can boost or cut high-frequency sounds from –10 dB to +10 dB in 1 dB steps.
Notes:
• The tone control circuits are bypassed when the Direct, Pure Audio or THX listening mode is selected.
• This setting is not available when the multichannel Analog input is selected.
• This procedure can also be performed on the AV con­troller by using its [TONE], [e], and [r] buttons (see page 66).
Multiplex/Mono Settings
Multiplex
Input Ch(Mux)
This setting determines which channel of a stereo multi­plex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.
Main: The main channel is output (default).
Sub: The sub channel is output.
Main/Sub:
Mono
Input Ch(Mono)
This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2-channel analog/PCM source in the Mono listening mode.
L+R: Both the left and right channels are output
L: Only the left channel is output.
R: Only the right channel is output.
Output Speaker
This setting determines which speakers output mono audio when the Mono listening mode is selected.
C: Mono audio is output by the center speaker
L/R: Mono audio is output by the front left and right
Both the main and sub channels are output.
(default).
(default).
speakers.
DSD Setting
DAC Direct
This setting determines whether or not DSD (SACD) audio signals are passed through the DSP for A/V Sync, delay, etc., processing when the Pure Audio or Direct lis­tening mode is selected.
No: DSD signals are processed by the DSP
(default).
Ye s : DSD signals are not processed by the DSP.
PLIIx/Neo:6 Settings
PLIIx Music(2ch Input)
These settings apply to only 2-channel stereo sources. If you’re not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx.
Panorama
With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.
On: Panorama function on.
Off: Panorama function off (default).
99
Page 100
Advanced Setup—Continued
Dimension
With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. It can be adjusted from –3 to +3. The default value is 0. Lower settings move the sound field forward. Higher settings move it backward.
If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.
Center Width
With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output by only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom cen­ter). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. It can be adjusted from 0 to 7. The default value is 3.
Neo:6 Music
Center Image
The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. It can be adjusted from 0 to 5. The default value is 2.
When set to 0, the front left and right channel output is attenuated by half (–6 dB), giving the impression that the sound is located centrally. This setting works well when the listening position is considerably off center. When set to 5, the front left and right channels are not attenu­ated, maintaining the original stereo balance.
Theater-Dimensional (T–D) Setting
Listening Angle
With this setting, you can optimize the Theater-Dimen­sional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equi­distant from the listening position and at an angle close to one of the two available settings.
Front left speaker Front right speaker
30˚
Wide: Select if the angle is greater than 30 degrees
(default).
Narrow: Select if the angle is less than 30 degrees.
LFE Level Settings
With these settings, you can set the level of the LFE (Low Frequency Effects) channel individually for Dolby Digital, DTS, and multichannel PCM sources. The level can be set to –
If you find that low-frequency effects are too loud when using one of these sources, change the setting to –20 dB or –dB.
Dolby Digital
Sets the level of the LFE channel for Dolby Digital and Dolby Digital Plus sources.
DTS
Sets the level of the LFE channel for DTS and DTS-HD High Resolution sources.
Multich PCM
Sets the level of the LFE channel for multichannel PCM sources. (Multichannel PCM is input via HDMI.)
, –20 dB, –10 dB, or 0 dB (default).
Dolby EX Settings
Dolby EX
This setting determines how Dolby EX signals are han­dled.
Aut o: When the source is Dolby EX, you can select
the Dolby EX or THX Surround EX listening mode (default).
Manual: When the source is Dolby EX, you can select
any of the listening modes compatible with this format (e.g., Dolby EX, Dolby Pro Logic IIx, etc.).
100
Dolby TrueHD
Sets the level of the LFE channel for Dolby TrueHD sources.
DTS-HD Master Audio
Sets the level of the LFE channel for DTS-HD Master Audio sources.
DSD
Sets the level of the LFE channel for DSD sources.
Loading...