Using the remote controller
Overview
When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then press the operation buttons. For example, if you wish to control the TX-DS575 from a remote controller, first press the MODE AUDIO button, then press an appropriate operation button. To control a CD player, press the MODE CD button, then press an appropriate operation button.
First, press the desired MODE button to make sure that the TX-DS575 is set to a correct mode.
SEND indicator
POWER ON POWER STNBY
MODE AUDIO
POWER ON |
|
|
SLEEP |
POWER |
|
STNBY |
||
|
MODE
AUDIO
DISPLAY
CH +/– |
VOL |
TEST
MUTING
|
INPUT |
|
SELECTOR |
|
Litening |
|
mode |
SP A/B |
LEVEL +/– |
DIMMER |
CH SEL |
Using the RC-391M to control each device
Turning the power on and off to the TX-DS575
Note:
Before operating the RC-391M, turn on the POWER switch on the TX-DS575 so that the unit enters standby mode.
1.Press the MODE AUDIO button.
2.Pressing the POWER ON buttons will switch between power on.
Pressing the POWER STNBY button will power standby.
SEND indicator
This indicator acts as a guide when commands are programmed into or sent by the remote controller. It also warns the user when an error is made or battery power is low.
Controlling the TX-DS575
1.Press the MODE AUDIO button.
2.Press the desired operation button.
Shaded buttons in the figure are the operation buttons used to control the TX-DS575.
SLEEP : Sleep function
POWER ON/STNBY
: Power on/standby DISPLAY : Changing the display VOL q/u : Adjusting the volume
CH +/– : Tuner preset number increment/decrement
INPUT SELECTOR
Listening mode (STEREO/DSPÃ/DSP¨/SURROUND) : Changing Listening mode
SP A/SP B : Switching between Speakers A and B
CH SEL |
: Selecting a speaker |
DIMMER |
: Adjusting the brightness of the display |
LEVEL +/– |
: Adjusting the speaker levels |
TEST |
: Test tone |
MUTING |
: Muting |
31
Using the remote controller
MODE CD
CD operation buttons
Numeric keys
MODE DVD
DVD |
operation |
buttons |
Numeric keys,
ENT button
Controlling an Onkyo CD player
Note:
First connect an Onkyo CD player using the connection.
1.Press the MODE CD button.
2.Press the desired CD operation button.
TRACK : Selecting a track
DISC |
: Selecting a disk in the CD changer |
|
: Down |
|
: Up |
|
: Playback |
|
: Stop |
|
: Rewind |
|
: Fast forward |
|
: Pause |
EJECT |
: Eject |
0, 1~9, +10 |
: Numeric keys |
You may also use the following buttons:
VOL q/u : Adjusting the volume level of the TXDS575
MUTING : Muting the sound from the TX-DS575
Controlling an Onkyo DVD player
Note:
Make sure that you point the transmission part on the remote controller toward the sensor area on the DVD player.
1.Press the MODE DVD button.
2.Press the desired DVD operation button.
POWER ON/STNBY
:Turning the power on and off to the DVD player
DVD SET |
: DVD setup |
DVD player on-screen button |
|
MENU |
: Displaying the menu |
ququ |
: Moving the cursor |
ENTER |
: Confirming the selection |
RETURN |
: Return |
DVD player buttons |
|
|
: Down |
|
: Up |
|
: Playback |
|
: Stop |
|
: Rewind |
|
: Fast forward |
|
: Pause |
EJECT |
: Eject |
0, 1~9, +10 |
: Numeric keys |
ENT |
: Confirm |
You may also use the following buttons:
VOL q/u : Adjusting the volume level of the TXDS575
MUTING : Muting the sound from the TX-DS575
Note:
|
The ENT button on the right below the numeric keys has the same |
32 |
function as “ENTER” of the ENTER/cursor button. |
|
Using the remote controller
MODE MD
MD operation buttons
Numeric keys,
ENT button
MODE
AUDIO
TAPE operation buttons
MODE SAT,
CABLE, VCR,
TV
Controlling an Onkyo MD recorder
Note:
Make sure that you point the transmission part on the remote controller toward the sensor area on the MD recorder.
1.Press the MODE MD/AUX button.
2.Press the desired MD operation button.
Turning the power on and off to the MD recorder
POWER ON/STNBY
:Turning on or standby the power to the MD recorder
|
: Down |
|
: Up |
|
: Playback |
|
: Stop |
|
: Rewind |
|
: Fast forward |
REC |
: Record |
|
: Pause |
EJECT |
: Eject |
1~9, +10 |
: Numeric keys |
ENT |
: Confirm |
You may also use the following buttons:
VOL q/u : Adjusting the volume level of the TXDS575
MUTING : Muting the sound from the TX-DS575
Controlling an Onkyo tape deck
Note:
First connect an Onkyo tape deck using the connection. (See page 9.)
1.Press the MODE AUDIO/TAPE button.
2.Press the desired tape deck operation button.
|
: Playback |
|
: Stop |
|
: Rewind |
|
: Fast forward |
REC |
: Recording/pause |
|
: Reverse playback |
You may also use the following buttons:
VOL q/u : Adjusting the volume level of the TXDS575
MUTING : Muting the sound from the TX-DS575
MODE SAT, CABLE, VCR, and TV buttons
No preset codes are programmed into the MODE SAT, CABLE, VCR, and TV buttons. You can use these buttons to program remote controller signals of other devices. (See page 34.)
You may use the following buttons:
VOL q/u : Adjusting the volume level of the TXDS575
MUTING : Muting the sound from the TX-DS575
33