Onkyo HT-R420 User Manual
AV Receiver
HT-R420
Instruction Manual
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver. Please retain
this manual for future reference.
Contents
Before using
Important safeguards ........................................ 2
Precautions........................................................ 3
Features ............................................................. 4
Supplied accessories ......................................... 4
Before using the HT-R420 ............................... 5
Facilities and connections
Index to parts and controls ............................... 6
Connecting to audio/video equipment ........... 10
Positioning speakers/Connecting speakers .... 12
Connecting antennas ....................................... 14
Connections for remote control (z) ............. 16
Enjoying music or videos
Enjoying music or videos with the
HT-R420 ....................................................... 17
Speaker setup .................................................. 18
Changing the default settings according
to your connections ...................................... 21
Listening to the radio ...................................... 22
Various functions common to all the sources ..
Enjoying multi channel sources ..................... 27
Enjoying the listening modes ......................... 28
Audio adjust function ..................................... 30
Recording a source ......................................... 32
Remote controller
Using the remote controller with your other
AV components ............................................ 33
24
Appendix
Troubleshooting .............................................. 38
Specifications ........................... back cover page
En
Important_En Page 2 Thursday, January 15, 2004 4:42 PM
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
PORTABLE CART WARNING
S3125A
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and follow local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is adequate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a flue-like
gap for warm air to escape.
2
Precautions
For U.S. models
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Section 820-40 of the NEC which provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building,
as close to the point of cable entry as practical.
FCC information for user
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
For Canadian models
THIS CLASS B DIGITAL APPARATUS COMPLIES
NOTE:
WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modèle pour les Canadien
REMARQUE:
CLASSE B EST CONFORME A LA NORME NMB-003 DU
CANADA.
Sur les modèles dont la fiche est polarisée:
CET APPAREIL NUMÉRIQUE DE LA
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
1. Recording Copyright—Unless it’s for personal use only,
recording copyrighted material is illegal without permission of
the copyright holder.
2. AC Fuse—The AC fuse inside the HT-R420 is not userserviceable. If you cannot turn on the HT-R420, contact your
Onkyo dealer.
3. Care—Occasionally you should dust the HT-R420 all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and water.
Dry the HT-R420 immediately afterwards with a clean cloth.
Don’t use abrasive cloths, thinners, alcohol, or other chemical
solvents, because they may damage the finish or remove the
panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
AC outlet voltages vary from country to country. Make sure that
the voltage in your area meets the voltage requirements printed on
the HT-R420’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V,
60 Hz).
The Worldwide model has a voltage selector for compatibility
with power systems around the world. Before you plug in this
model, make sure that the voltage selector is set to the correct
voltage for your area.
Setting the [STANDBY/ON] switch to STANDBY does not fully
shutdown the HT-R420. If you do not intend to use the HT-R420
for an extended period, remove the power cord from the AC outlet.
3
Features
Amplifier Features
•5 × 100 W/Channel @ 8Ω, 20–20 kHz, 0.08% THD
•WRAT-Wide Range Amplifier Technology
• Optimum Gain Volume Circuitry
• DTS, Dolby Digital, Dolby Pro Logic II
• CinemaFILTER
• Non-Scaling Configuration
• A-Form–Auto Format Sensing
• Linear PCM 96 kHz/24-bit D/A Converters
• Advanced 24-bit DSP Chips
•3 S-Video Inputs/1 Output
•2 Digital Inputs (Optical/Coaxial)
• Subwoofer Pre Out
• Dot Matrix FL Display
• Crossover Adjustment (60/80/100/120/150 Hz)
• Color-Coded Speaker Posts
Supplied accessories
FM/AM Tuner Features
• 30 FM/AM random presets
•FM auto tuning
•FM indoor antenna supplied
•AM indoor antenna supplied
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
** “DTS” and “DTS Digital Surround” are registered trademarks of
Digital Theater Systems, Inc.
Check that the following accessories are supplied with the HT-R420.
AM loop antenna × 1
Power-plug adapter
Only supplied in certain countries. Use this adapter if your AC
outlet does not match with the plug on the HT-R420's power cord.
(Adapter varies from country to country.)
The alphabet displayed at the end of the product name found in catalogs and on the packages represents the color of this receiver. Though the
color varies, the specifications and operations are the same.
FM indoor antenna × 1
(Connect type varies from
country to country.)
Remote controller × 1
America ........RC-518M
Others ..........RC-479S
Batteries (AA/R6) × 2
75/300-ohm antenna adapter
(Not supplied with American model.)
4
Before Using the HT-R420
Setting the Voltage Selector
(Worldwide model only)
The Worldwide model has a voltage selector for compatibility with
power systems around the world. Before you plug in this model,
make sure that the voltage selector is set to the correct voltage for
your area. If it isn't, use a small screwdriver to set it as appropriate.
For example, if the voltage in your area is 120 volts (V), set the
selector to “120V.” And if it’s between 220 and 230 volts (V), set it
to “220-230V.”
AC OUTLET
SWITCHED
100W MAX.
VOLTAGE
SELECTOR
120 V
220-230 V
VOLTAGE
SELECTOR
120 V
220-230 V
Installing the Batteries
1 Open the battery compartment, as shown.
Notes
• The supplied batteries should last for about six months,
although this will vary with usage.
• If the remote controller doesn’t work reliably, try replacing
both batteries.
• Don’t mix new and old batteries, or different types of batteries.
• If you intend not to use the remote controller for a long time,
remove the batteries to prevent possible leakage and corrosion.
• Flat batteries should be removed as soon as possible to prevent
possible leakage and corrosion.
Using the Remote Controller
To use the remote controller, point it at the HT-R420’s remote
control sensor, as shown below. The HT-R420’s STANDBY
indicator flashes while a signal is being received from the remote
controller.
Remote control sensor
HT-R420
Standby indicator
30˚
30˚
Approx. 16 feet (5m)
2 Insert the two supplied batteries (AA/R6) in
accordance with the polarity diagram inside the
battery compartment.
3 Close the battery compartment.
Notes
• The remote controller may not work reliably if the HT-R420 is
subjected to bright light, such as direct sunlight or inverter-type
fluorescent lights. Keep this in mind when installing the HTR420.
• If another remote controller of the same type is used in the same
room, or the HT-R420 is installed close to equipment that uses
infrared rays, the remote controller may not work reliably.
• Don’t put anything, such as a book, on the remote controller,
because the buttons may be pressed inadvertently, thereby
draining the batteries.
• The remote controller may not work reliably if the HT-R420 is
installed in a rack behind colored glass doors. Keep this in mind
when installing the HT-R420.
• The remote controller will not work if there’s an obstacle
between it and the HT-R420’s remote control sensor.
5
Index to parts and controls
Front panel
1234567890-=
~! @# $ ^%
For operational instructions, refer to the page indicated in brackets.
1 STANDBY/ON button [17]
When STANDBY/ON button is pressed to ON, the display will
light to show the current volume setting for about 5 seconds then
show the current sound input source. Pressing the button again
returns the HT-R420 to the standby state. This state turns off the
display, disables control functions.
2 STANDBY indicator [17]
Lights when the HT-R420 is in the standby state and flashes when a
signal is received from the remote controller.
3 DIMMER button [25]
Press to set the brightness of the front display. The brightness
changes to normal, dim and very dim.
4 DIGITAL INPUT button [21]
When digital components are connected to the DIGITAL INPUT
jacks of the HT-R420, use this button to assign the DIGITAL
INPUT jacks to them according to their forms of connection.
5 SUBWOOFER MODE button [20]
Press to select the subwoofer mode.
6 MEMORY button [23]
This button is used to assign the radio station that is currently tuned
in to a preset channel or delete a previously preset station.
8 TUNING ™/£ buttons [22]
Use these buttons to change the tuner frequency.
When FM is selected, you can hold down one of the TUNING
™/£ buttons and then release it to activate the auto-search
feature. It will search for a station in the direction of the button you
pressed and stop when it tunes into one.
9 Remote control sensor [5]
This sensor receives the control signals from the remote controller.
0 LISTENING MODE buttons [27, 29]
Press these buttons to select a listening mode for the current source.
Press the DSP button to recall the Onkyo-original DSP modes in
sequence. Press the DIRECT, STEREO or SURROUND button to
recall the corresponding listening mode directly.
- PRESET/ADJUST ™/£ buttons [18, 19, 23,
30]
These buttons make it possible to store desired radio stations under
the desired preset numbers and recall them with an easy operation.
Also, these buttons adjust the values and parameters of the mode
selected using the AUDIO ADJUST, SPEAKER ADJUST or
AUDIO SELECTOR button.
= MASTER VOLUME dial [17]
The MASTER VOLUME dial is used to control the volume level.
Turn the dial clockwise to increase the volume level and
counterclockwise to decrease it.
7 FM MODE button [22, 23]
Press to switch the reception mode between stereo and monaural. If
audio is interrupted or noise interferes with audio during FM stereo
broadcasting, press this button to switch to the monaural reception
mode.
6
~ SPEAKERS A/B buttons [17, 24]
Press SPEAKERS A/B to turn on/off the speaker system A/B. The
(SPEAKERS) A/B indicators corresponding to the selected speaker
system light up. You can use SPEAKERS A and B simultaneously.
! PHONES jack [24]
This is a standard stereo jack for connecting stereo headphones.
The audio for the front right and left speakers are sent to the
headphone speakers.
Index to parts and controls
Display
ab c def
hi
g
@ DISPLAY button [25]
Each time you press the DISPLAY button, the display changes.
# AUDIO SELECTOR button [26, 27]
Press to select an audio input signal format other than FM and AM.
Each time this button is pressed, the setting cycles.
$
Input selector buttons (DVD, VIDEO 1, VIDEO 2,
VIDEO 3, TAPE, TUNER, and CD) [17, 21-23, 26,
27, 32]
These buttons are used to select the input source. Pressing and
holding the TAPE button for about 2 seconds allows the TAPE and
MD sources to be switched.
% SPEAKER ADJUST button [18, 19]
Press to select speaker setting item.
^ AUDIO ADJUST button [30]
Press to adjust bass, treble, late night function, cinema filter,
Panorama, Dimension and Center Width function setting.
a (SPEAKERS) A/B indicators [17, 24]
Shows the current speaker system in use.
b MUTING indicator [24]
Flashes when the mute function is active.
c Source/Listening mode indicators [17, 29]
One of these indicators lights to show the format of the current
source as “PCM”, “Ÿ DIGITAL” or “DTS”. In addition, one of the
listening mode indicators “Ÿ PRO LOGIC II”, “MULTI CH”,
“DSP”, “STEREO” and “DIRECT” lights according to the current
listening mode.
d TUNED indicator [22]
Lights up when a radio station is received.
e MEMORY indicator [23]
Lights up when the MEMORY button is pressed in the radio station
preset operation.
f AUTO indicator [22]
Lights up to indicate auto reception mode (stereo/monaural). At
this time, interstation noise will be muted (FM only). It
extinguishes when the monaural reception mode is started by
pressing the FM MODE button.
g FM STEREO indicator [22]
Lights up when an FM stereo broadcast station is received.
h SLEEP indicator [25]
Lights up when the sleep timer is active.
i Multi function display
In usual operation, shows the current input source and volume.
When the FM or AM input is selected, it shows the frequency and
preset number. When the DISPLAY button is pressed, it shows the
current input source and the listening mode.
7
Index to parts and controls
Rear panel
1
DIGITAL INPUT
COAXIAL
OPTICAL
REMOTE
CONTROL
IN
OUT
IN
L
SUBWOOFER
PRE OUT
R
TAPE
CD
7
6 8 9 q wp
IN
VIDEO 3
AM
VIDEO 2VIDEO 3
VIDEO 2
2
FM
75
ANTENNA
VIDEO 1
DVD MONITOR
IN
OUT
IN
OUT
ININ
OUT
IN
VIDEO 1
OUT
IN
IN
IN
IN
FRONT
S VIDEO
VIDEO
SURR
CENTER
L
R
SUB
WOOFER
DVD
For operational instructions, refer to the page indicated in brackets.
1 z REMOTE CONTROL [16]
Connect the Onkyo components that have z connectors such as a
CD player, and cassette tape deck using the z cables provided
with them. When these components are interconnected, they can be
controlled from the remote controller provided with the
HT-R420.
For correct operation, the audio connection cables must also be
connected. This applies to both remote and standard operation.
2 ANTENNA [14, 15]
These terminals are for connecting the FM antenna and AM
antenna.
3 FRONT SPEAKERS B [13]
These terminals are for connecting the speaker system B.
4 FRONT SPEAKERS A, CENTER SPEAKER
and SURROUND SPEAKERS [13]
These terminals are for connecting the speaker system A, including
the center and surround speakers.
354
FRONT
SPEAKERS B
FRONT
SPEAKERS A
RLRL
CENTER
SPEAKER
SURROUND
SPEAKERS
RL
AC OUTLET
8 CD IN [10]
Connect the output terminal on the CD player to the CD IN L/R
jacks on the HT-R420.
9 TAPE IN/OUT [10]
Connect the output terminals (PLAY) of the cassette tape deck or
MD recorder to the TAPE IN L/R jacks on the HT-R420 and the
input terminals (REC) to the TAPE OUT L/R jacks.
p VIDEO 1 IN/OUT, VIDEO 2 IN, VIDEO 3 IN [11]
Connect the output terminals (PLAY) of the video cassette recorder
to the VIDEO 1 IN L/R jacks on the HT-R420 and the input
terminals (REC) to the VIDEO 1 OUT jacks.
Connect the output terminals of the video cassette player or satellite
tuner to the VIDEO 2 IN or VIDEO 3 IN jacks on the HT-R420.
q DVD [11]
Connect the DVD player. If the DVD player has 5.1 channel output
terminals, connect each terminal to the FRONT L/R, CENTER,
SUBWOOFER, and SURR L/R terminals on the HT-R420. If the
DVD player has only 2 channel output terminals, connect to the
FRONT L/R terminals on the HT-R420.
5 AC OUTLET [11]
The HT-R420 is supplied with AC outlet for connecting the power
cord from other devices so that their power is supplied through the
HT-R420. By doing this, you can use the STANDBY/ON button on
the HT-R420 to turn on and off the connected devices as well.
6 DIGITAL INPUT OPTICAL, COAXIAL
[10, 11]
These are digital audio inputs. There is 1 optical jack and 1 coaxial
jack. The inputs accept digital audio signals from DVD, LD, CD, or
other digital source.
7 SUBWOOFER PRE OUT [13]
This terminal is for connecting an active subwoofer.
8
w MONITOR OUT [10]
The monitor output includes both RCA type and S video
configurations. This output is for connecting television monitors or
projectors.
Tip
The audio input jacks of the HT-R420 do not accept direct
connection of an analog turnable.
If you want to connect a turntable to the HT-R420 prepare a phono
equalizer and connect it to the unused audio input jacks (IN L/R).
Refer to the instruction manuals of the phono equalizer and
turntable for details.
Index to parts and controls
Remote controller
RC-518M (American model)
1
2
3
4
5
6
7
8
9
0
-
=
~
!
@
#
Explanations on this page are for controlling the HT-R420. To
operate other components, see “Using the remote controller with
your other AV components” on pages 33 through 37.
For operational instructions, refer to the page indicated in brackets.
1 SLEEP button [25]
For setting the sleep time.
This button is provided only on the remote controller.
2 STANDBY/ON button [17]
Turns on the HT-R420 or put it in standby.
3 Listening mode buttons [27, 29]
Press to change the listening mode.
4 CINE FLTR button [30]
Press to activate/deactivate Cinema Filter function.
5 LATE NIGHT button [30]
Press to change the late night setting.
6 TEST/CH SEL/LEVEL 5/∞ buttons [20, 26]
For setting the output levels for each speaker.
These buttons are provided only on the remote controller.
7 AUDIO SEL button [26, 27]
Press to select an audio input signal format.
RC-479S (Other models)
1
2
3
4
5
6
7
8
9
0
-
=
~
!
@
#
8 INPUT SELECTOR buttons [17, 21-23, 26, 27,
32]
For selecting the input source.
9 MUTING button [24]
Activates the mute function.
This button is provided only on the remote controller.
0 PRESET 2/3 button [23]
For selecting a tuner preset channel.
- DIMMER button [25]
For adjusting the brightness of the front display.
= Mode buttons [33-37]
For selecting the component to be operated by the remote
controller. The RC-518M remote controller has five mode buttons,
the RC-479S has three.
~ SP A/SP B buttons [17, 24]
Press to switch the speaker systems.
! AUDIO ADJUST button [30]
Press to adjust bass, treble, late night function and cinema filter
function setting.
@ ADJUST 2/3 button [30]
Press to adjust the values and parameters of the mode selected
using the AUDIO ADJUST, SPEAKER ADJUST or AUDIO
SELECTOR button.
# VOLUME 5/∞ button [17]
For adjusting the volume.
9
Connecting to audio/video equipment
Before connecting
• Be sure to always refer to the instruction manual that came
with the component that you are connecting.
• Do not plug in the power cord until all connections have
been made.
• For input jacks, red connectors are used for the right
channel, white connectors are used for the left channel, and
yellow connectors are used for video connection.
• Insert all plugs and connectors securely. Improper connections
can result in noise, poor performance, or damage to the
equipment.
Improper connection
Inserted completely
• Do not bind audio connection cables with power cords and
speaker cables. Doing so may adversely effect the sound
quality.
TV monitor or Projector
(MONITOR OUT)
S VIDEO
VIDEO
IN
IN
Video Connection Formats
Video equipment can be connected to the HT-R420 using the
following video connection formats : Video or S Video, the latter
offering the better picture quality.
When choosing a connection format, bear in mind that the HTR420 doesn’t convert between format, so only output connectors of
the same format as the input connector will output a signal.
For example, if you connect your DVD player to the S VIDEO
DVD IN, a video signal will be output by the S VIDEO MONITOR
OUT (for your TV) and the S VIDEO VIDEO 1 OUT (for your
VCR), but not the composite video outputs.
VIDEO
S video plug
Audio (L)
Audio (R)
Optical plug
Video connection cable
(Analog signal)
S video connection cable
(S video signal)
Audio connection cable
(Analog signal)
Optical fiber cable
(Digital signal)
Signal flow
DIGITAL INPUT
OPTICAL
IN
L
SUBWOOFER
PRE OUT
R
CD
RL
DIGITAL
AUDIO OUT
OUT
(PLAY)
OPTICAL
CD player (CD)
COAXIAL
OUT
TAPE
REMOTE
CONTROL
IN
IN
VIDEO 3
AM
VIDEO 2VIDEO 3
VIDEO 2
FM
ANTENNA
75
VIDEO 1
DVD MONITOR
IN
OUT
IN
OUT
ININ
OUT
IN
VIDEO 1
OUT
IN
IN
IN
IN
SURR
FRONT
L
R
DVD
RL RL
AUDIO IN
(REC)
CENTER
SUB
WOOFER
AUDIO OUT
Cassette Tape deck, MD recorder,
DAT deck, CD recorder (TAPE)
S VIDEO
VIDEO
(PLAY)
FRONT
SPEAKERS B
FRONT
SPEAKERS A
RLRL
CENTER
SPEAKER
SURROUND
SPEAKERS
RL
AC OUTLET
DO NOT connect the
power cord at this
time.
• To connect the digital output from a component
connected to the TAPE jacks to this unit, use the
OPTICAL or COAXIAL input jack.
In this case, it is required to change the assignment of
digital inputs to input sources by referring to “Setting the
digital inputs” on page 21.
• The TAPE OUT jack does not output the signal input
from the DIGITAL INPUT jack. (The digital signal is not
converted into an analog signal.)
• To connect the digital output from CD player connected
to the CD jacks to this unit, use the OPTICAL input jack.
To connect the digital output to the COAXIAL input jack
of this unit, it is required to change the assignment of
digital inputs to input sources by referring to “Setting the
digital inputs” on page 21.
10
Connecting to audio/video equipment
Video Camera,
Game Device, etc.
(VIDEO 3)
VIDEO
AUDIO
OUT
OUT
LR
4
*
SUBWOOFER
PRE OUT
3
*
DIGITAL INPUT
OPTICAL
IN
L
R
CD
DVD player or component
with 5.1 ch output (DVD)*
S VIDEO
DIGITAL
OUT
COAXIAL
2
*
OUT
VIDEO
OUT
FRONT
LR
AUDIO OUT
SURR
LR
1
CENTER
SUBWOOFER
Caution
Make sure that the capacity of the other components connected
to this unit does not exceed the capacity that is printed on the
rear panel (ex. 120 watts).
FM
AM
75
ANTENNA
FRONT
SPEAKERS A
RLRL
SURROUND
CENTER
SPEAKERS
SPEAKER
RL
DO NOT connect the
power cord at this
time.
AC OUTLET
COAXIAL
OUT
TAPE
REMOTE
CONTROL
IN
IN
VIDEO 3
VIDEO 2VIDEO 3
IN
ININ
IN
VIDEO 2
OUT
OUT
OUT
VIDEO 1
VIDEO 1
IN
IN
IN
DVD MONITOR
OUT
IN
IN
SURR
FRONT
L
R
DVD
CENTER
SUB
WOOFER
S VIDEO
VIDEO
FRONT
SPEAKERS B
To connect the digital
output from satellite
tuner etc. connected to
the VIDEO 1, VIDEO 2
or VIDEO 3 jacks to the
Video
Audio (L)
Audio (R)
Audio/video
connection
cable
COAXIAL or OPTICAL
input jack of this unit, it is
required to change the
assignment of digital
inputs to input sources by
referring to “Setting the
digital inputs” on page
21.
AUDIO
OUT
VIDEO
OUT
S VIDEO
OUT
3
*
RL RLLR
VIDEO
AUDIO
AUDIO
IN
VIDEO
IN
S VIDEO
IN
OUT
OUT
S VIDEO
OUT
3
*
S video plug
Coaxial plug
S video cable
(S video signal)
Coaxial cable
(Digital signal)
Signal flow
Video cassette player,
Satellite tuner, LD
5
*
, etc. (VIDEO 2)
player
VCR (VIDEO 1)
*1If the DVD player has both 5.1 channel audio outputs and 2 channel audio outputs, and you want to connect the DVD player only using
the FRONT L/R jacks on the HT-R420, use the 2 channel audio output jacks on the DVD player.
If the DVD player only has the 2 channel audio outputs, connect it to the FRONT L/R jacks.
2
To connect the digital output from DVD player connected to the DVD jacks to this unit, use the COAXIAL input jack.
*
To connect the digital output to the OPTICAL input jack of this unit, it is required to change the assignment of digital inputs to input
sources by referring to “Setting the digital inputs” on page 21.
3
Be sure to make the same video connection (either S-VIDEO or standard VIDEO) between your component(s), the receiver, and your TV.
*
*4VIDEO3 does not have an S VIDEO terminal. Therefore, check that the TV connected to MONITOR OUT is also connected to the
VIDEO terminal.
5
If you have an LD player with AC-3RF output, connect via an AC-3RF demodulator to one of the HT-R420’s DIGITAL INPUT
*
terminals.
11
Positioning speakers/Connecting speakers
Two speaker systems can be connected to the Receiver.
The speaker system A is to be placed in the main room, and the speaker system B is to be placed in a second room.
The speaker system A consists of the FRONT SPEAKERS A (L/R), CENTER SPEAKER, SURROUND SPEAKERS (L/R) and
SUBWOOFER.
You can reproduce the sounds such as Dolby surround and DTS surround.
The speaker system B consists of the FRONT SPEAKERS B.
You can reproduce only monaural and stereo sounds.
Standard speaker placement of the speaker system A
Speaker placement plays an important role in the reproduction of
Surround sound.
The placement of the speakers varies depending on the size of the room
and the wall coverings used in the room. The illustration below shows an
example of a layout for standard speaker placement. Refer to this example
when you position the speakers in order to experience the best of
Surround sound.
For ideal Surround effects, all speakers should be installed.
If a center speaker or subwoofer is not connected, the sound from the
unused channel is properly distributed to the connected speakers in order
to reproduce the best Surround sound possible.
Front
The center speaker reproduces a richer sound image by enhancing the
perception of the sound’s source and movement.
The left, right, and center speakers should face the seated listener and be
placed at ear level.
Surround
The surround speakers reproduce the feel of a moving sound while
creating the sensation of being in the middle of the action.
Place the left and right surround speakers 3 feet (1 meter) above the
listener’s ear level and facing toward the sides of the room, making sure
that the listener is within the speakers’ dispersion angle.
Subwoofer
When bass sound is reproduced, its volume and quality greatly depend on
subwoofer placement. Those characteristics also depends on the shape of
your listening room as well as your listening point. Generally speaking,
good bass sound is obtained when the subwoofer is placed in the corner of
the room or at one-third the length of the room.
Refer to the speakers’ instruction manuals for details.
Surround
left speaker
1/3 room
length
Front
left speaker
1/3
1/3
TV/Screen
Center
speaker
1/3
Front
right speaker
Subwoofer
Surround
right speaker
Corner
12
Loading...