Onkyo DV-CP500 User Manual

DVD Changer

DV-CP500

Instruction Manual

Contents

Before Using Your DVD Changer 2

Getting Started 6

Facilities and Connections 10

Thank you for purchasing the Onkyo DVD Changer. Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new DVD Changer. Please retain this manual for future reference.

Basic Operation 17

Advanced Operation 20

Function Setup 30

Others 37

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important Safeguards

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

AVIS

OUVRIR

NE PAS

1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions – The safety and operating instructions should be retained for future reference.

3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Cleaning – Unplug the appliance from the wall outlet before cleaning. The appliance should be cleaned only as recommended by the manufacturer.

6. Attachments – Do not use attachments not recommended by the appliance manufacturer as they may cause hazards.

7. Water and Moisture – Do not use the appliance near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories – Do not place the appliance on an unstable cart, stand, tripod, bracket, or table. The appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the appliance. Any mounting of the appliance should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the appliance and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the appliance on a bed, sofa, rug, or other similar surface. The appliance should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. There should be free space of at least 5 cm (2 in.) and an opening behind the appliance.

11. Power Sources – The appliance should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company.

12. Grounding or Polarization – The appliance may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

PORTABLE CART WARNING

S3125A

13. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

Lightning – For added protection for the appliance during a

14. lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the appliance due to lightning and power-line surges.

15. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16. Object and Liquid Entry – Never push objects of any kind into the appliance through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance.

17. Servicing – Do not attempt to service the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service – Unplug the appliance form the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen into the

appliance, C. If the appliance has been exposed to rain or water, D. If the appliance does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the appliance to its normal operation,

If the appliance has been dropped or damaged in any way, and

E. F. When the appliance exhibits a distinct change in

performance – this indicates a need for service.

19. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20. Safety Check – Upon completion of any service or repairs to the appliance, ask the service technician to perform safety checks to determine that the appliance is in proper operation condition.

21. Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

23. Liquid Hazards – The appliance shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the appliance.

Precautions

This unit contains a semiconductor laser system and is classified as a “CLASS 1 LASER PRODUCT”. So, to use this model properly, read this Instruction Manual carefully. In case of any trouble, please contact the store where you purchased the unit. To prevent being exposed to the laser beam, do not try to open the enclosure.

CAUTION:

VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. DO NOT STARE INTO BEAM.

CAUTION:

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

“CLASS 1 LASER PRODUCT ”

1. This unit is a CLASS 1 LASER PRODUCT and employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not remove the cover. Refer servicing to qualified personnel.

The laser is covered by a housing which prevents exposure during operation or maintenance. However, this product is classified as a Laser Product by CDRH (Center for Devices and Radiological Health) which is a department of the Food and Drug Administration. According to their regulations 21 CFR section

1002.30, all manufactures who sell Laser Products must maintain records of written communications between the manufacturer, dealers and customers concerning radiation safety. If you have any complaints about instructions or explanations affecting the use of this product, please feel free to write to the address on the back page of this manual. When you write us, please include the model number and serial number of your unit.

In compliance with Federal Regulations, the certification, identification and the period of manufacture are indicated on the rear panel.

FCC INFORMATION FOR USER

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian model

This class B digital apparatus complies with Canadian ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Sur les modèles dont la fiche est polarisee:

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Precautions

1. Regional Restriction Codes (Region Number)

Regional restriction codes are built into DVD Changers and DVD-Video media for each sales region. If the regional code of the DVD Changer does not match one of the regional codes on the DVD-Video, playback is not possible. The regional number can be found on the rear panel of the DVD

Changer.

(e.g. for Region 1)

2. About This Manual

This manual explains the basic procedures for operating the DVD Changer. Some DVD-Video discs do not support the full potential of the DVD technology. Your DVD Changer may

therefore not respond to all operating commands. Refer to instruction notes on discs.

” mark may appear on the TV screen during operation. It

A “ means that the operation is not permitted by the DVD Changer or the disc.

3. Recording Copyright

Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where the unit will be used meets the required voltage (e.g., AC 120 V, 60 Hz) written on the rear panel.

5. Do not touch the unit with wet hands

Do not handle the unit or power cord when your hands are wet or damp. If water or any other liquid enters the case, take the unit to an authorized service center for inspection.

6. Location of the unit

• Place the unit in a well-ventilated location.

Take special care to provide plenty of ventilation on all sides of the unit especially when it is placed in an audio rack. If ventilation is blocked, the unit may overheat and malfunction.

• Do not expose the unit to direct sunlight or heating units as

the unit’s internal temperature may rise and shorten the life of the pickup.

• Avoid damp and dusty places and places directly affected by

vibrations from the speakers. In particular, avoid placing the unit on or above one of the speakers.

• Be sure the unit is placed in a horizontal position. Never

place it on its side or on a slanted surface as it may malfunction.

• When you place the unit near a TV, radio, or VCR, the

playback picture may become poor and the sound may be distorted. In this case, place the unit away from the TV, radio, or VCR.

7. Care

From time to time you should wipe the front and rear panels and the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak solution of mild detergent and water, wring it out dry, and wipe off the dirt. Following this, dry immediately with a clean cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the finish or remove the panel lettering.

8. Notes on Handling

• When shipping the unit, use the original shipping carton and packing materials. For maximum protection, repack the unit as it was originally packed at the factory.

• Do not use volatile liquids, such as insect spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long time. They will leave marks on the finish.

• The top and rear panels of the unit

a long period of use. This is not a malfunction.

• When the unit is not in use, be sure to remove the disc and turn off the power.

• If you do not use the unit for a long period, the unit may not function properly in the future. Turn on and use the unit occasionally.

9. To Obtain a Clear Picture

The unit is a high technology, precision device. If the optical pick-up lens and disc drive parts are dirty or worn down, the picture quality becomes poor. To obtain a clear picture, we recommend regular inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the operating environment. For details, contact your nearest dealer.

10. Notes on Moisture Condensation

Moisture condensation damages the unit. Please read the following carefully.

• What is moisture condensation?

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the optical pick-up lens inside the unit, one of the most crucial internal parts of the unit.

• Moisture condensation occurs in the following cases.

– When you bring the unit directly from a cold place to a

warm place.

– When you use the unit in a room where you just turned on

the heater, or a place where the cold wind from the air conditioner directly hits the unit.

– In summer, when you use the unit in a hot and humid

place just after you move the unit from an air conditioned room.

– When you use the unit in a humid place.

• Do not use the unit when moisture condensation may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After a few hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

may become warm after

Table of Contents

Important Safeguards / Precautions / Table of Contents............................ 2 - 5

Getting Started

Notes on Discs .................................................................................................... 6

Playable Discs / The Structure of the Disc Content / About Video CDs / MP3 Compatibility Information / Handling Discs / Cleaning Discs / Storing Discs / Notes on Copyright

Features/Supplied Accessories ......................................................................... 8

Features / Supplied Accessories

Preparing the Remote Controller....................................................................... 9

Inserting the Batteries / Using the Remote Controller

Facilities and Connections

Control Position and Names ............................................................................ 10

Front Panel / Rear Panel / Display / Remote Controller

Making Connections ......................................................................................... 14

Connections to a TV / Optional Video Connections / Optional Audio Connections

Basic Operations

Turning on.......................................................................................................... 17

Connecting the POWER

Basic Playback .................................................................................................. 18

Starting Playback / Various Playback

Advanced Operations

Using Banner Display ....................................................................................... 20

Using the On-screen Banner Display / Selecting a Title / Selecting a Chapter or Track / Selecting a Playback Audio Setting / Changing the Subtitle Language / Changing the Camera Angle / Using IntroScan Function / Using a Bookmark

Other Operations .............................................................................................. 25

CD PLAY Function / Random Play / Repeat Play / A-B Repeat Play / Memory Play / Progressive Scan Function

MP3 Function ................................................................................................................... 28

Playing Back MP3 / Selecting MP3 Files / MP3 Repeat Playback / MP3 Memory Playback

Function Setup

Customizing the Settings ................................................................................. 30

Making Adjustments to Setting / Language Setting / Operation Setting / Picture Setting / Audio Setting

Table of Languages........................................................................................... 36

Table of Language and Their Code No.

Others

Troubleshooting ................................................................................................ 37

Specifications .................................................................................................... 38

Notes on Discs

This section shows you how to handle, clean, and store discs.

Playable Discs

This DVD Changer can playback the following discs.

Disc mark

DVD-

Video

CD-R*

CD-RW*

* The DVD Changer can play CD-R/RW discs recorded in

CD-DA format, or with MP3 audio files. Some CD-R/RW discs may not be able to be played back.

• You cannot play discs such as DVD-Audio, DVD-RAM etc., even if the marks in the above table are labeled on those discs.

• This DVD Changer uses the NTSC color system, and cannot playback video media recorded in any other color system (SECAM, etc.).

• Avoid using heart-shaped or octagonal discs. Playing irregularly shaped discs may damage the internal mechanism of the DVD Changer.

Contents

Audio

Video (moving pictures)

Audio +

Video (moving pictures)

Audio

Discs with shapes such as these cannot be played.

Disc size

12 cm

8 cm

12 cm

8 cm

12 cm

8 cm (CD single)

The Structure of the Disc Content

DVD-Video

Normally, the contents of DVD-Video are divided into titles, and the titles are subdivided into chapters.

Title 1

Chapter 1

Video CD/CD

Video CD and CD are divided into tracks.

Track 1 Track 2

Chapter 2

Chapter 1

Track 3

Title 2

Chapter 2

Track 4 Track 5

Chapter 3

About Video CDs

This DVD Player supports Video CDs equipped with the PBC (Version 2.0) function. (PBC is the abbreviation of Playback Control.) You can enjoy two playback variations depending on the type of disc.

• Video CD not equipped with PBC function (Version 1.1)

Sound and movies can be played on this DVD Player in the same way as a CD.

• Video CD equipped with PBC function (Version 2.0)

In addition to operation of the Video CD not equipped with the PBC function, you can enjoy playback with interactive software and search function using the menu displayed on the TV screen (Menu Playback). Some of the functions described in this Instruction Manual may not work with some discs.

• Do not use discs that have residue from adhesive tape, rental discs that have peeling labels, or discs that have custom labels or stickers. Otherwise, you may not be able to eject the discs or the DVD Changer may become inoperative.

• Use CD-R or CD-RW media for recording your CD audio files or MP3 files. The disc must be finalized in order to play.

MP3 Compatibility Information

• The CD-R or CD-RW must be ISO 9660 level 1 compatible.

• Files should be MPEG1 Audio Layer 3 format, 32 kHz, 44.1 kHz (recomended) or 48 kHz, 32 kbps - 320 kbps (128 kbps recomended). Incompatible files will not play.

• This system only plays tracks that are named with the file extension “.mp3” or “.MP3”.

• This system is not compatible with multi-session discs.

Handling Discs

Notes on Copyright

• Do not touch the playback side of the disc.

Playback side

• Do not attach paper or tape to discs.

Cleaning Discs

• Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

• If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth.

• Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material without permission. The video recorded on DVD-Video is copy protected, and any recordings made from these discs will be distorted. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Storing Discs

• Do not store discs in a place subject to direct sunlight or near heat sources.

• Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier.

• Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Features/Supplied Accessories

Features

● Plays DVD-Video Discs, Video CDs, CDs

● 10-bit Video DAC

● Simultaneous output to all video connections

● Digital Outputs pass DTS®*1, Dolby®*2 Digital and PCM Signals

● Built-In Dolby® Digital decoder

● Full-function remote controller

● Direct Digital path

● Plays 5 Discs

● CD-R and CD-RW playable

● Plays MP3

● CD PLAY function for audiophile

● Pass 96 kHz PCM digital stream

Supplied Accessories

Make sure your box contains everything listed below. If any pieces are missing, contact your nearest Onkyo dealer. The number of accessories is indicated in brackets [ ].

*1“DTS” and “DTS Digital Out” are trademarks of Digital Theater

Systems, Inc.

*2Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Remote controller (RC-502DV) [1]

Coaxial cable [1]

Audio/video cable [1]

Batteries (size AAA/R3) [2]

Preparing the Remote Controller

Inserting the Batteries

1 Remove the battery compartment cover by

pressing the tab and lifting up the cover.

2 Insert the two batteries (size AAA/R3).

Be sure to match the + and – ends of the batteries with the diagram inside the battery compartment.

3 Replace the battery compartment cover.

Using the Remote Controller

Point the remote controller toward the remote control sensor.

Remote control sensor

30˚

Approx. 16 feet

Notes

• Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can prevent proper operation of the remote controller.

• Using another remote controller of the same type in the same room or using the unit near equipment which uses infrared rays may cause operational interference.

• Do not put any object such as a book on the remote controller. The buttons of the remote controller may be pressed by mistake and drain the batteries.

• Make sure the audio rack doors do not have colored glass. Placing the unit behind such doors may prevent proper remote controller operation.

• If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate.

Notes

• Do not mix new batteries with old batteries or different kinds of batteries.

• To avoid corrosion, remove the batteries if the remote controller is not to be used for a long time.

• Remove dead batteries immediately to avoid damage from corrosion. If the remote controller does not operate smoothly, replace both batteries at the same time.

• The life of the batteries supplied is about six months but this will vary depending on usage.

Control Position and Names

Front Panel

For operational instructions, see the page indicated in brackets [ ].

23 4 5 6 7890

1 POWER button [17]

Turns on the main power supply.

2 STANDBY indicator [17]

Lights in the standby mode.

3 STANDBY/ON button [17]

Toggle for standby on and off.

4 CD PLAY button [25]

Press to use the DVD Changer as CD player.

5 Front panel display [12]

6 DISC SKIP button [18]

Press to select a disc. When the DISC SKIP button is pressed while the disc tray open, the tray simply rotates.

7 4/¢ buttons [19]

Allow you to move to the previous chapter or track / the next chapter or track on a disc.

8 STOP 7 button [18]

Stops playing a disc. When disc is playing, if you press 7 and £, the disc will start resume play. When 7 is pressed again

during stop mode, the resume function is canceled.

9 PLAY/PAUSE £/8 button [18]

Begins to play disc (close disc tray first if it is open.) Temporarily stops playback when a disc is playing. Press this button again for normal playback.

0 DISC 1-5 buttons [18]

Press to select a disc.

- Disc tray [18]

= 0 OPEN/CLOSE button [18]

Press to open or close the disc tray.

Control Position and Names

Rear Panel

For operational instructions, see the page indicated in brackets [ ].

VIDEO OUTPUT

COMPONENT

VIDEO

12 3 4 5 6

AUDIO

OUTPUT

DIGITAL OUTPUT

OPTICAL

COAXIAL

DVD CHANGER

MODEL NO.

DV-CP

500

VIDEO OUTPUT COMPONENT (PR/PB/Y) jacks [15]

If your TV has component inputs, you can connect a component video cable to your TV and to your DVD Changer for ideal video quality. The component video cable only carries the video signal; remember to connect the left and right audio cables. If you connect a TV that is compatible with a Progressive scan signal, you can enjoy both Interlaced and Progressive scan.

2 VIDEO OUTPUT S VIDEO jack [15]

If your TV has a S-Video jack, you can connect an S-Video cable to your TV and to your DVD Changer for improved video quality. The S-Video cable only carries the video signal; remember to connect the left and right audio cables.

3 VIDEO OUTPUT VIDEO jack [14]

Connect a video cable to this jack and to the Video Input jack on your TV.

4 AUDIO OUTPUT jacks [14-16]

Insert audio cables (left and rights) to these jacks on your DVD Changer and to the corresponding Audio Input jacks (left and right) on your TV or receiver.

5 DIGITAL OUTPUT COAXIAL jack [16]

Use coaxial cable to connect your DVD Changer to an AV component that features digital input capability. If the component has a Dobly Digital or DTS decoder, you can enjoy theater-quality multichannel sound.

6 DIGITAL OUTPUT OPTICAL jack [16]

Use optical cable to connect your DVD Changer to an AV component that features digital input capability. If the component has a Dolby Digital or DTS decoder, you can enjoy theater-quality multichannel sound.

Control Position and Names

Display

1234657 8 90 =

!~@

1 Inserted disc indicators

Indicate the type of disc that is currently loaded.

2 PROGRESSIVE indicator

Illuminates when the DVD changer is set to progressive mode.

3 Parental Lock indicator

Illuminates in parental lock mode.

4 TITLE indicator

Illuminates to indicate the current title number.

5 RESUME indicator

Illuminates when the player is ready for resume playback.

■ Display Examples

During DVD-Video playback:

DVD

Playing disc 1

Notes

• Some discs may not display chapter numbers.

• A time indication not accompanied by a chapter number shows elapsed time

of a segment within the current time.

TITLE CHAPTER MIN

Playing chapter 3 of title 2

SEC

Elapsed time of the current title

6 CHAPTER/TRACK indicators

Indicate display mode of the current chapter of DVD disc or track number of Video CD or CD.

7 RANDOM indicator

Illuminates during random playback.

8 REPEAT indicators

Illuminate during repeat playback.

9 MEM. indicator

Illuminates during memory playback.

0 PBC indicator

Illuminates when PBC is on for Video CD.

- INTRO indicator

Illuminates during intro-scan playback.

= Elapsed time indicators

Indicate playing time.

~ Play/Pause indicators

Illuminate in play or pause mode.

! Disc number indicator/CD indicator

Disc number indicators indicate the presence of a disc. CD indicator illuminates when the DVD Changer is in CD PLAY mode.

@ Multifunction indicator

Indicates operating status, messages, etc.

During Video CD playback:

Playing disc 1

VCD

TRACK MIN

Playing track 3

SEC

Elapsed time of the current track

Note

Some discs may not display track numbers or elapsed time.

During CD playback:

Playing disc 1

During MP3 playback:

DVD

MP3

Playing disc 1

TRACK MIN

Playing track 3

TITLE CHAPTERTRACK MIN

Playing track 105 of folder 6

Elapsed time of the current track

Elapsed time of the current title

SEC

Notes

• If the track is within a folder, the folder number is displayed. For tracks outside a folder, no folder number is displayed.

• Track number is consecutive.

+ 28 hidden pages