One for All AR90, AR85, SD9500, Wireless Universal Garage Remote User Manual
Retain for Future Reference
Thank you for purchasing the One For
All
Wireless Universal Garage Remote. Your
One For All Wireless Universal Garage
Remote (referred to as GDK throughout
the rest of the manual) is designed to
operate most garage door openers as well
as most gate openers manufactured after
1981*.
Your GDK will operate the following
manufacturer’s products:
Before getting started, you will need your
original garage door opener transmitter.
You will use the original transmitter during
the setup of the GDK. If you do not have
your original transmitter, please refer to the
“WHAT TO DO IF YOUR ORIGINAL
TRANSMITTER HAS TWO OR THREE
BUT-TONS OR IS LOST OR BROKEN”
section after setting up your password.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
l
Sears Craftsman (Most units)
Genie:
Model AR85 (9-Position Switch)
Model AR90 (12-Positions Switch)
Model SD9500 (12-Positions
Switch)
Stanley
Chamberlain (Most Units)
Linear
Moore-o-Matic
Multi-Code
Wayne Dalton
Lift-Master
Master Mechanics
Ambassador
Automatic DoorMan
Doorkeeper
Liftadoor
Multi El Mac
Raynor
Shima
Vemco
Crawford
Powerlift
Blue Max
EZ
Lift
Your GDK package contains the following
items:
.
1 - One For All Wireless Universal
Garage Remote
.
1 - Users Manual
.
1
- 9-volt
battery
.
2
- 1” flathead
screws for mounting the
One For All Wireless Universal Garage
Remote
The GDK comes with one fresh 9-volt
battery. The battery is packaged inside the
battery compartment along with the two
1"
mounting screws, however, the battery is
not connected. To connect the battery:
1.
3.
Slide off the battery cover
and remove the battery and
two mounting screws.
Connect the battery.
Insert the connected battery
inside the battery
compartment and replace
the battery cover.
1.
2.
mx8
oo*I
Slide open the cover. The GDK’s
keypad will illuminate.
Press the number 9 eight times, then
press ENTER, the GDK will beep
once and the green LED will
w
illuminate for two seconds followed
by two quick beeps. The GDK will
power OFF. This clears the GDK of
any previous passwords and
securitycodes so that you can
begin a new setup. Your GDK has
now ready to learn your new
password and garage door security
code(s).
NOTE: Use the reset code only to clear
the GDK of all passwords and garage door
security codes.
1.
Select a PIN (Personal Identification Number) and write it down.
This will be your password. Your
PIN can be up to 8 digits long.
Press the ENTERkey to illuminate
&
the GDK’s keypad.
3. w
Press tne
number 1 (Factory
’
Default Password) followed by
v
ENTER. The green LED will blink
two times followed by one beep.
The GDK is now on and ready to
learn your new password (PIN).
Pres
s STORE followed by the
PlN1, PIN2* or PIN3* key. The first
red LED, corresponding to PIN1,
will light and remain lit as the
green LED blinks.
*NOTE:
The first time you enter a
password, GDK automatically defaults that
password to PIN1, even if PIN2 or PIN3 is
pressed.
5.
PIN
Enter the PIN you wrote down in
B
STEP 1 then press ENTER. The
GDK will emit a double-ticking sound
to prompt you to confirm your new
PIN
password. Now reenter the PIN and
w
press ENTER again. If you entered
the
same PIN correctly, the green
LED will illuminate for three seconds
followed by two beeps. The GDK will
then power OFF.
NOTE: If you make a mistake in entering
your PIN, press the EXIT key and return to
STEP 2 to re-enter your new
PIN.
You will need your original garage door
opener when setting up GDK’s garage
door security code. Open your original
garage door opener so that you can view
the DIP switches.
1
.PlN
Open the GDK’s cover or, if the
w
cover is already open, press
ENTER. Key in your PIN followed
by ENTER. The GDK will beep and
the green light will blink twice if the
PIN is correctly entered. If you
enter your PIN incorrectly, the GDK
will beep and the red light will blink
once.
Press STORE followed by
DOOR1,
DOOR2 or DOOR3. The
first six
LEDs
will chase. Enter the
number (1-6) from the table for
your brand of garage door
opener (See Figure 4). The
corresponding LED will light.
NOTE: If you make a mistake during the set
up
process,
press the EXIT key, re-enter your
PIN and return to
step 1 in
the
"SETTlNG
UP
THE
SECURITY CODE TO OPERATE
YOUR
GARAGE DOOR" section to
re-enter
your garage door opener’s code.
I
MULTI-CODE
AMBASSADOR
MULTI EL MAC
MOORE-O-MATIC
LINEAR
DELTA
SHIMA
POWERLIFT
3
GENIE MODEL
AT90
GENIE MODEL
SD9500
LIFTADOOR
BLUE MAX
EZ LIFT
4
GENIE MODEL
AR85
5
CHAMBERLAIN
SEARS
RAYNOR
LIFT-MASTER
WAYNE DALTON
MASTER
MECHANIC
STANLEY
6
AUTOMATIC
DOORMAN
VEMCO
10 BITS/300
MHZ
8
BITS/310
MHZ
12
BITS/390
MHZ
9
BITS/390
MHZ
9
BITS/390
MHZ
TERTIARY BITS
10
BITS/31
0 MHZ
3.
Press ENTER. All of the
LEDs
will
w
begin to chase, then the first LED
will blink.
Using the UP, MID and DOWN
keys, match the
LEDs
to the DIP
switches in your original garage
door opener. When you press UP,
the LED will remain on. When you
press MID, the LED will flash
slowly and when you press
DOWN, the LED will remain off.
NOTE: The
LEDs must m
atch exactly to
the
DIP switches on your original garage
door opener.
Loading...