OMRON NX-EIC Instruction Manual

Download

NX-series EtherNet/IPTM Coupler Unit

EtherNet/IP master CJ-series CPU Unit or master from another manufacturer

Communications cable Ethernet cables

NX-series EtherNet/IP Coupler Unit NX-EIC202

Sysmac Studio Support Software

End Cover

NX Units *

EtherNet/IP port

EtherNet/IP Unit

Peripheral USB port

Network Configurator

Connection to peripheral USB port on EtherNet/IP Coupler Unit

Industrial Switching Hubs W4S1

EDS files

Sysmac is a trademark or registered trademark of OMRON Corporation in Japan and other countries for OMRON factory automation products. EtherCAT



is a registered trademark of Beckhoff Automation GmbH for their patented technology. EtherNet/IPTM is the trademarks of ODVA.

Other company names and product names in this document are the trademarks or registered trademarks of their respective companies.

NX-EIC

CSM_NX-EIC_DS_E_4_3

Connecting to open industrial network standard EtherNet/IP

• The EtherNet/IP Coupler Unit is the link between the EtherNet/IP multivendor network and the NX-series I/O Units and Safety Units. With wide variety of the I/O Units and Safety Units, the NX-series is the perfect match for the CJ-series and multivendor Controllers.

Features

• Up to 63 NX-IO Units can be connected to one EtherNet/IP Coupler Unit. Standard and high-performance units can be mixed.*

• Each Coupler plus its I/O form just a single EtherCAT node on the network.

• I/O control and safety control can be integrated by connecting Units for safety.

• The IP address can be found on the label on the Unit, without using software.

• Slave configuration by Sysmac Studio can be done centrally via the controller, or on-the-spot using the Coupler's built-in USB port.

* Input per Coupler Unit: Maximum 504 bytes, Output per Coupler Unit: Maximum 504 bytes

System Configuration

System Configuration of Slave Terminals

Note: Do not make a loop connection in the communications path between Ethernet switches.

* Refer to Configuration Unit on page 8 for the NX Units that can be connected to the NX-series EtherNet/IP Coupler Unit.

NX-EIC

Ordering Information

Applicable standards

Refer to the OMRON website (www.ia.omron.com) or ask your OMRON representative for the most recent applicable standards for each model.

EtherNet/IP Coupler Unit

Product name Current consumption Maximum I/O power supply current Model

EtherNet/IP Coupler Unit

1.60 W or lower 10 A NX-EIC202

Automation Software Sysmac Studio

Please purchase a DVD and required number of licenses the first time you purchase the Sysmac Studio. DVDs and licenses are available individually. Each model of licenses does not include any DVD.

Product name Specifications Model

Sysmac Studio NX-I/O Edition is a limited license that

Sysmac Studio NX-I/O Edition Ver.1.@@

Sysmac Studio Standard Edition Ver.1.@@

*1. Model "SYSMAC-SE200D-64" runs on Windows 10 (64 bit). *2. The Sysmac Studio Standard Edition with license(s) (SYSMAC-SE@@@L) provides functions of the NX-I/O Edition (SYSMAC-NE001L). *3. With the Sysmac Studio Standard Edition with license(s) (SYSMAC-SE@@@L) version 1.10 or higher, you can use the setup functions for the

EtherNet/IP Coupler.

*4. Multi licenses are available for the Sysmac Studio (3, 10, 30, or 50 licenses).

provides selected functions required for EtherNet/IP Coupler settings. Because this product is a license only, you need the Sysmac Studio Standard Edition DVD media to install it.

The Sysmac Studio is the software that provides an integrated environment for setting, programming, debugging and maintenance of machine automation controllers including the NJ/NX-series CPU Units, NYseries Industrial PC, EtherCAT Slave, and the HMI.

Sysmac Studio runs on the following OS. Windows 7 (32-bit/64-bit version)/ Windows 8 (32-bit/64-bit version)/ Windows 8.1 (32-bit/64-bit version)/ Windows 10 (32-bit/64-bit version) *1

This software provides functions of the Vision Edition. Refer to your OMRON website for details such as supported models and functions.

Number of

licenses

1 license --- SYSMAC-NE001L

--(Media only)

1 license *2 *3 *4 --- SYSMAC-SE201L

Media

Sysmac

Studio (32-bit)

DVD

Sysmac

Studio

(64-bit)

DVD

SYSMAC-SE200D

SYSMAC-SE200D-64

NX-EIC

Connecting Cable

Peripheral (USB) Port

Use a commercially available USB-certified cable. Specifications: USB 1.1 or 2.0 cable (A connector - B connector), 5.0 m max.

Recommended EtherNet/IP Communications Cables

For EtherNet/IP, required specification for the communications cables varies depending on the baud rate. For 100BASE-TX/10BASE-T, use a straight or cross STP (shielded twisted-pair) cable of category 5 or higher. For 1000BASE-T, use a straight or cross STP cable of category 5e or higher with double shielding (aluminum tape and braiding).

Cable with Connectors

Item Appearance

Cable with Connectors on Both Ends (RJ45/RJ45) Standard RJ45 plugs type *1 Wire Gauge and Number of Pairs: AWG26, 4-pair Cable Cable Sheath material: LSZH *2 Cable color: Yellow *3

Cable with Connectors on Both Ends (RJ45/RJ45) Rugged RJ45 plugs type *1 Wire Gauge and Number of Pairs: AWG22, 2-pair Cable Cable color: Light blue

Cable with Connectors on Both Ends (M12 Straight/M12 Straight) Shield Strengthening Connector cable *4 M12/Smartclick Connectors Wire Gauge and Number of Pairs: AWG22, 2-pair Cable Cable color: Black

Cable with Connectors on Both Ends (M12 Straight/RJ45) Shield Strengthening Connector cable *4 M12/Smartclick Connectors Rugged RJ45 plugs type Wire Gauge and Number of Pairs: AWG22, 2-pair Cable Cable color: Black

*1. Standard type cables length 0.2, 0.3, 0.5, 1, 1.5, 2, 3, 5, 7.5, 10, 15 and 20 m are available. Rugged type cables length 0.3, 0.5, 1, 2, 3, 5, 10

and 15 m are available. For details, refer to Cat.No.G019.

*2. The lineup features Low Smoke Zero Halogen cables for in-cabinet use and PUR cables for out-of-cabinet use. Although the LSZH cable is

single shielded, its communications and noise characteristics meet the standards. *3. Cables colors are available in blue, yellow, or Green. *4. For details, contact your OMRON representative.

Recommended

manufacturer

OMRON

Cable length (m) Model

0.3 XS6W-6LSZH8SS30CM-Y

0.5 XS6W-6LSZH8SS50CM-Y

1 XS6W-6LSZH8SS100CM-Y

2 XS6W-6LSZH8SS200CM-Y

3 XS6W-6LSZH8SS300CM-Y

5 XS6W-6LSZH8SS500CM-Y

0.3 XS5W-T421-AMD-K

0.5 XS5W-T421-BMD-K

1 XS5W-T421-CMD-K

2 XS5W-T421-DMD-K

5 XS5W-T421-GMD-K

10 XS5W-T421-JMD-K

0.5 XS5W-T421-BM2-SS

1 XS5W-T421-CM2-SS

2 XS5W-T421-DM2-SS

3 XS5W-T421-EM2-SS

5 XS5W-T421-GM2-SS

10 XS5W-T421-JM2-SS

0.5 XS5W-T421-BMC-SS

1 XS5W-T421-CMC-SS

2 XS5W-T421-DMC-SS

3 XS5W-T421-EMC-SS

5 XS5W-T421-GMC-SS

10 XS5W-T421-JMC-SS

Cables / Connectors

Protrusions for removing the Unit

Unit hookup guide

Protrusions for removing the Unit

Item Recommended manufacturer Model

Products for EtherNet/IP (100BASE-TX)

*1. We recommend you to use above cable for EtherNet/IP and RJ45 Connector together. *2. We recommend you to use above cable for EtherNet/IP and RJ45 Assembly Connector together.

Wire Gauge and Number of Pairs: AWG24, 4-pair Cable

Wire Gauge and Number of Pairs: AWG22, 2-pair Cable

Cables

RJ45 Connectors Panduit Corporation MPS588-C *1

Cables

RJ45 Assembly Connector

Hitachi Cable, Ltd.

Kuramo Electric Co. KETH-SB *1

SWCC Showa Cable Systems Co. FAE-5004 *1

Kuramo Electric Co. KETH-PSB-OMR *2

JMACS Japan Co., Ltd. PNET/B *2

OMRON XS6G-T421-1 *2

NETSTAR-C5E SAB

× 4P CP *1

0.5

Optional Products

Product name Specification Model

Unit/Terminal Block Coding Pins

Product name

Terminal Block 8 A/B Provided 10 A NX-TBC082

Pins for 10 Units (30 terminal block pins and 30 Unit pins)

No. of terminals

Terminal number

indications

Specification

Ground terminal

mark

Terminal current

capacity

NX-AUX02

NX-EIC

Model

Accessories

End Cover (NX-END01)

One End Cover is provided together with the EtherNet/IP Coupler Unit.

NX-EIC

General Specification

Item Specification Enclosure Mounted in a panel Grounding method Ground to 100 Ω or less

Ambient operating temperature 0 to 55°C Ambient operating humidity 10% to 95% (with no condensation or icing) Atmosphere Must be free from corrosive gases. Ambient storage temperature −25 to 70°C (with no condensation or icing) Altitude 2,000 m max.

Operating environment

Applicable standards *2

*1. Refer to the NX-series Digital I/O Units User’s Manual (Cat. No. W521) for the vibration and shock resistance specifications of the Relay Output

Unit.

*2. Refer to the OMRON website (http://www.ia.omron.com/) or consult your OMRON representative for the most recent applicable standards for

each model.

Pollution degree Pollution degree 2 or less: Meets IEC 61010-2-201. Noise immunity Conforms to IEC 61000-4-4. 2 kV (power supply line) Overvoltage category Category II: Meets IEC 61010-2-201. EMC immunity level Zone B

Vibration resistance

Shock resistance Conforms to IEC 60068-2-27. 147 m/s2, 3 times each in X, Y, and Z directions *1

Conforms to IEC 60068-2-6. 5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz, acceleration of 9.8 m/s2, 100 min each in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total) *1

cULus: Listed UL508, ANSI/ISA 12.12.01 EU: EN 61131-2, C-Tick or RCM, KC: KC Registration

EtherNet/IP Coupler Unit Specifications

Item Specification Model NX-EIC202 Number of connectable NX Units 63 Units max.*1

EtherNet/IP

Number of buffers (sockets):

• 8 message buffers for server

• No message buffers for client

• Shared buffers for UDP/IP messages and TCP/IP

Communications protocols

Modulation Baseband Link speed 100 Mbps Physical layer 100BASE-TX (IEEE 802.3) Number of connections 8 Received Packet Interval (RPI, refresh cycle) 4 to 1,000 ms Allowed communications bandwidth

addressing to the local node Topology Line, Tree, Star Ethernet Switch Layer 2 Ethernet switch

Transmission media

Transmission distance Distance between nodes: 100 m or less

NX bus I/O data size

EtherNet/IP I/O connection size

Refreshing methods Free-Run refreshing

Power supply voltage 24 VDC (20.4 to 28.8 VDC) NX Unit power supply capacity 10 W max. (Refer to Installation orientation and restrictions for details.)

Unit power supply *2

I/O power supply *2

NX Unit power consumption 1.60 W max. Current consumption from I/O power supply 10 mA max. (for 24 VDC)

*1. Refer to the NX-series Safety Control Unit User's Manual (Cat. No. Z930) for the number of Safety Control Units that can be connected. *2. Refer to the NX-series EtherNet/IP™Coupler Unit User’s Manual (Cat. No. W536) for procedures for designing the Unit power supply system

and I/O power supply system.

*3. Use a voltage that is appropriate for the I/O circuits of the NX Units and the connected external devices.

NX Unit power supply efficiency Isolation method No isolation between NX Unit power supply and Unit power supply terminals Current capacity of power

supply terminals Power supply voltage 5 to 24 VDC (4.5 to 28.8 VDC) *3 Maximum I/O power supply current Current capacity of power

supply terminals

UDP/IP and TCP/IP (Message Services)

1,000 pps

Category 5 or higher twisted-pair cable (Recommended cable: double-shielded cable with aluminum tape and braiding)

Input: 512 bytes max. (including input data, status, and unused areas) Output: 512 bytes max. (including output data and unused areas)

Input: 504 bytes max. (including input data, status, and unused areas) Output: 504 bytes max. (including output data and unused areas)

70%

4 A max.

10 A (Refer to Installation orientation and restrictions for details.)

10 A max.

messages

Maximum message size:

• Request: 492 bytes

• Response: 496 bytes

Maximum NX output data size:

• 490 bytes

Maximum NX input data size:

• 496 bytes

Item Specification

0 10 20 30 40 45 50 55 60

Ambient temperature [°C]

Unit power supply [W]

10 W output, 40°C

8.5 W output, 55°C

0 10 20 30 40 45 50 55 60

Ambient temperature [°C]

Unit power supply [W]

10 W output, 40 °C

6.0 W output, 55°C

0 10 20 30 40 45 50 55 60

Ambient temperature [°C]

°C

6 A current, 55°C

10 A current, 45

I/O power supply [A]

Dielectric strength 510 VAC for 1 min, leakage current: 5 mA max. (between isolated circuits) Insulation resistance 100 VDC, 20 MΩ min. (between isolated circuits)

Communications Connector For EtherNet/IP communications.

• RJ45 × 2 (shielded)

External connection terminals

Dimensions 46 × 100 × 71 mm (W×H×D) Weight 150 g max.

Screwless Clamping Terminal Block For Unit power supply, I/O power supply, and grounding. Removable.

Peripheral USB Port For Sysmac Studio connection.

• Physical layer: USB 2.0-compliant, B-type connector

• Transmission distance: 5 m max.

Installation orientation: 6 possible orientations Restrictions:

• Used in the upright installation orientation.

NX-EIC

Installation orientation and restrictions

• Used in any other orientation than the upright installation orientation.

Circuit layout

NX Unit power supply +

NX Unit power supply −

Terminal block

I/O power supply +

I/O power supply −

DIN Track contact plate

Peripheral USB port

IN communications connector

OUT communications connector

NX bus connector

UV UG

IOV

IOG

UNIT PWR LED

I/O PWR LED

Internal circuits

Non-isolated power supply circuits

IOV

IOG

Unit power supply

(24 VDC)

Through-wiring

for unwired

terminals.

I/O power supply

(5 to 24 VDC)

Ground to 100 Ω

or less.

NX-EIC

Item Specification

Terminal arrangement

Accessory End Cover (NX-END01): 1

Configuration Unit

Refer to the user's manuals for information on the NX Units that can be connected to the NX-series EtherNet/IP Coupler Unit.

EtherNet/IP Coupler Unit

Unit Model

EtherNet/IP Coupler Unit NX-EIC202

I/O Units

Unit

Digital Input Unit −

Digital Output Unit

Digital Mixed I/O Unit −−−

Analog Input Unit

Analog Output Unit

Temperature Input Unit

Heater Burnout Detection Unit −

2-point Units 4-point Units 8-point Units 16-point Units 32-point Units

NX-ID3317 NX-ID3343 NX-ID3417 NX-ID3443 NX-IA3117

NX-OD3121

NX-OC2633 NX-OC2733

NX-AD2603 NX-AD2604 NX-AD2608 NX-AD2203 NX-AD2204 NX-AD2208

NX-DA2603 NX-DA2605 NX-DA2203 NX-DA2205

NX-TS2101 NX-TS2102 NX-TS2104 NX-TS2201 NX-TS2202 NX-TS2204

NX-OD3153 NX-OD3256 NX-OD3257 NX-OD3268

NX-AD3603 NX-AD3604 NX-AD3608 NX-AD3203 NX-AD3204 NX-AD3208

NX-DA3603 NX-DA3605 NX-DA3203 NX-DA3205

NX-TS3101 NX-TS3102 NX-TS3104 NX-TS3201 NX-TS3202 NX-TS3204

NX-HB3101 NX-HB3201

Model

NX-ID4342 NX-ID4442

NX-OD4121 NX-OD4256 NX-OC4633

NX-AD4603 NX-AD4604 NX-AD4608 NX-AD4203 NX-AD4204 NX-AD4208

NX-ID5142-1 NX-ID5142-5 NX-ID5342 NX-ID5442

NX-OD5121 NX-OD5121-1 NX-OD5121-5 NX-OD5256 NX-OD5256-1 NX-OD5256-5

NX-MD6121-5 NX-MD6121-6 NX-MD6256-5

−−

−−−

NX-EIC

NX-ID6142-5 NX-ID6142-6

NX-OD6121-5 NX-OD6256-5

−

Temperature Control Units

Unit

Temperature Control Unit NX-TC2405, NX-TC2406, NX-TC2407, NX-TC2408 NX-TC3405, NX-TC3406, NX-TC3407, NX-TC3408

2CH 4CH

Model

Load Cell Input Unit

Unit Model

Load Cell Input Unit NX-RS1201

Position Interface Units

Unit

Incremental Encoder Input Unit NX-EC0112, NX-EC0122, NX-EC0132, NX-EC0142 NX-EC0212, NX-EC0222

SSI Input Unit NX-ECS112 NX-ECS212

Pulse Output Unit NX-PG0112, NX-PG0122 −

1CH 2CH

Model

Communications Interface Units IO-Link Master Unit

Unit Model

Communications Interface Unit

NX-CIF101, NX-CIF105, NX-CIF210

IO-Link Master Unit NX-ILM400

Unit Model

System Units Safety Control Units

Unit Model

Additional NX Unit Power Supply Unit NX-PD1000

Additional I/O Power Supply Unit NX-PF0630, NX-PF0730

I/O Power Supply Connection Unit

Shield Connection Unit NX-TBX01

NX-PC0010, NX-PC0020, NX-PC0030

Safety CPU Unit NX-SL3300 *1

Safety Input Unit NX-SIH400 *2, NX-SID800

Safety Output Unit NX-SOH200, NX-SOD400

*1. Safety CPU Unit Ver.1.1 or higher. *2. Safety Input Unit Ver.1.1 or higher.

Unit Model

NX-EIC

Version Information

Depending on the type and model of the Unit, some Units do not have all of the versions given in the corresponding versions. If a Unit does not have the specified version, support is provided by the oldest available version after the specified version. Refer to the user’s manuals for the specific Units for the relation between models and versions.

Connection to the NJ/NX-series CPU Unit or NY-series Industrial PC

NX-series CPU Unit or NY-series Industrial PC

EtherNet/IP Coupler Unit Corresponding unit version/version

Model Unit version

NX-EIC202

Ver.1.2 Ver.1.14 Ver.1.19 Ver.3.21 Ver.2.4 *

Ver.1.0 Not possible. Not possible. Not possible. Not possible.

Unit version of CPU Unit

or Industrial PC

Sysmac Studio version

* The CX-ConfiguratorFDT with version 2.2 or later can be used if it is connected to the peripheral USB port on the EtherNet/IP Coupler Unit.

NJ-series CPU Unit

EtherNet/IP Coupler Unit Corresponding unit version/version

Model Unit version

NX-EIC202

Ver.1.2 Ver.1.14 Ver.2.1 Ver.1.19 Ver.3.21 Ver.2.4 *

Ver.1.0 Not possible. Not possible. Not possible. Not possible. Not possible.

Unit version of CPU

Unit

* The CX-ConfiguratorFDT with version 2.2 or later can be used if it is connected to the peripheral USB port on the EtherNet/IP Coupler Unit.

Unit version of

CJ1W-EIP21

Network Configurator for

EtherNet/IP version

Sysmac Studio

version

Network

Configurator for

EtherNet/IP version

CX-ConfiguratorFDT

version

CX-

ConfiguratorFDT

version

Connection to CS/CJ/CP-series CPU Unit

CS1G/CS1H/CJ1H/CJ1M * CPU Units * Final order entry date for CJ1M:The end of March, 2021

EtherNet/IP Coupler Unit Corresponding unit version/version

Model Unit version

NX-EIC202

Unit version of CPU

Unit

Ver.1.2

Ver.1.0 Ver.1.00 *2 Ver.2.2

Ver.3.0 Ver.2.1 Ver.3.00

Unit version of

CS1W-EIP21/CJ1W-

EIP21

*1. The CX-ConfiguratorFDT with version 2.2 or later can be used if it is connected to the peripheral USB port on the EtherNet/IP Coupler Unit. *2. You can connect only to the peripheral USB port on the EtherNet/IP Coupler Unit. You cannot connect with any other path.

CJ2H-CPU6/CJ2M-CPU1/CP1H CPU Unit

EtherNet/IP Coupler Unit Corresponding unit version/version

Model Unit version

NX-EIC202

Unit version of CPU

Unit

Ver.1.2

Ver.1.0 Ver.1.00 *2 Ver.2.2

Ver.1.0 Ver.2.1 Ver.3.00

Unit version of

CJ1W-EIP21

CJ2H-CPU6-EIP CPU Unit

EtherNet/IP Coupler Unit Corresponding unit version/version

Model Unit version

NX-EIC202

Ver.1.2

Ver.1.0 Ver.1.00 *2 Ver.2.2

Unit version of CPU

Unit

Ver.1.5 Ver.2.1 Ver.3.00

Unit version of

CJ1W-EIP21

Network

Configurator for

EtherNet/IP version

Network

Configurator for

EtherNet/IP version

Network

Configurator for

EtherNet/IP version

NX-IO Configurator

version

Ver.1.00 Ver.2.4 *1

NX-IO Configurator

version

Ver.1.00 Ver.2.4 *1

NX-IO Configurator

version

Ver.1.00 Ver.2.4 *1

ConfiguratorFDT

version

ConfiguratorFDT

version

ConfiguratorFDT

version

CX-

CJ2M-CPU3 CPU Unit

EtherNet/IP Coupler Unit Corresponding unit version/version

Model Unit version

NX-EIC202

Unit version of CPU

Unit

Ver.1.2

Ver.1.0 Ver.1.00 *2 Ver.2.2

Ver.1.0 Ver.2.1 Ver.3.21

Unit version of

CJ1W-EIP21

Network

Configurator for

EtherNet/IP version

NX-IO Configurator

version

Ver.1.00 Ver.2.4 *1

CX-

ConfiguratorFDT

version

NX-EIC

Connection to the Sysmac Gateway

Sysmac Gateway

EtherNet/IP Coupler Unit Corresponding unit version/version

Model Unit version Sysmac Gateway version

NX-EIC202

Ver.1.2

Ver.1.0 Ver.1.00 *2 Ver.2.2

Ver.1.31 Ver.3.50

Network Configurator for

EtherNet/IP version

NX-IO Configurator

version

Ver.1.00 Ver.2.4 *1

CX-ConfiguratorFDT

version

NX-EIC

NX-EIC202

NET

(B) (D)

(E)

(C)

(F)

(C)

(G)

(A)

Eight-terminal Block

(A)

(B)

(C)

External Interface

EtherNet/IP Coupler Unit NX-EIC202

Letter Name Function

(A) NX bus connector

(B) Indicators The indicators show the current operating status of the Unit and the status of the power supply.

(D) Peripheral USB port This port is used to connect to the Sysmac Studio.

(E) Terminal block The terminal block is used to connect to the power supply cables and ground wire.

(F) Rotary switches

(G) DIP switch

This connector is used to connect the EtherNet/IP Coupler Unit to the NX Unit on the right of the Coupler Unit.

The rotary switches are used to set the last octet of the IP address of the EtherNet/IP Coupler Unit as an EtherNet/IP Slave. The address is set in hexadecimal.

The DIP switch is used to set the default node address of the EtherNet/IP Coupler Unit as an EtherNet/IP slave.

Terminal Block

Symbol Name Function

(A) Terminal number indications

(B) Release holes Insert a flat-blade screwdriver into these holes to connect and remove the wires.

The terminal numbers (A1 to A8 and B1 to B8) are displayed. The terminal number indicators are the same regardless of the number of terminals on the terminal block, as shown above.

Applicable Wires

1.6 mm max. (Terminals other than ground terminals)

2.0 mm max. (Ground terminals)

2.4 mm max. (Terminals other than ground terminals)

2.7 mm max. (Ground terminals)

8 to 10 mm

Conductor length (stripping length)

Using Ferrules

If you use ferrules, attach the twisted wires to them. Observe the application instructions for your ferrules for the wire stripping length when attaching ferrules. Always use plated one-pin ferrules. Do not use unplated ferrules or two-pin ferrules.

The applicable ferrules, wires, and crimping tool are given in the following table.

Terminal types Manufacturer Ferrule model

AI0,34-8 0.34 (#22)

AI0,5-8

AI0,5-10

Terminals other than ground terminals

Phoenix Contact

AI0,75-8

AI0,75-10

AI1,0-8

AI1,0-10

AI1,5-8

AI1,5-10

Ground terminals

AI2,5-10 2.0 *1

H0.14/12 0.14 (#26)

H0.25/12 0.25 (#24)

H0.34/12 0.34 (#22)

H0.5/14

Terminals other than ground terminals

Weidmuller

H0.5/16

H0.75/14

H0.75/16

H1.0/14

H1.0/16

H1.5/14

H1.5/16

*1. Some AWG 14 wires exceed 2.0 mm

and cannot be used in the screwless clamping terminal block.

Applicable wire

(AWG))

(mm

0.5 (#20)

0.75 (#18)

1.0 (#18)

1.5 (#16)

0.5 (#20)

0.75 (#18)

1.0 (#18)

1.5 (#16)

Phoenix Contact (The figure in parentheses is the applicable wire size.) CRIMPFOX 6 (0.25 to 6 mm

Weidmueller (The figure in parentheses is the applicable wire size.) PZ6 Roto (0.14 to 6 mm

, AWG 26 to 10)

Crimping tool

, AWG 24 to 10)

NX-EIC

When you use any ferrules other than those in the above table, crimp them to the twisted wires so that the following processed dimensions are achieved.

Using Twisted Wires/Solid Wires

If you use the twisted wires or the solid wires, use the following table to determine the correct wire specifications.

Terminals

Twisted wires Solid wire

Classification Current capacity Plated Unplated Plated Unplated

2 A max.

All terminals except ground terminals

Greater than 2 A and 4 A or less

Greater than 4 A

Possible

Possible *1

Ground terminals --- Possible Possible

*1. Secure wires to the screwless clamping terminal block. Refer to the Securing Wires in the USER'S MANUAL for how to secure wires. *2. With the NX-TB@@@1 Terminal Block, use twisted wires to connect the ground terminal. Do not use a solid wire.

Wire type

Possible Possible Possible

Possible

Not Possible

Not

Not Possible

Possible

Possible *2Possible

Wire size

0.08 to 1.5 mm AWG28 to 16

2.0 mm

Conductor length (stripping length)

8 to 10 mm

9 to 10 mm

<Additional Information> If more than 2 A will flow on the wires, use plated wires or use ferrules.

NX-EIC

NX-EIC202

NET

48.1

65.2

104.5

100

1.5

0.55

Dimensions (Unit: mm)

● EtherCAT Coupler Unit Only

● With Cables Connected

100 to 120

5.8

*1. This dimension depends on the specifications of the commercially available USB-certified cable. Check the specifications of the USB cable

that is used.

*2. This is the dimension from the back of the Unit to the communications cables.

• 100 mm: When an MPS588-C Connector is used.

• 120 mm: When an XS6G-T421-1 Connector is used.

USB cable

Communications cable

● End Cover

NX-EIC

1.5

100

1.5

Related Manuals

Man. No Model Manual Application Description

W536 NX-EIC@@@

NX-series EtherNet/IP Coupler Unit User’s Manual

Learning how to use an NXseries Ether-Net/IP Coupler Unit and EtherNet/IP Slave Terminals

Introduces the system, configuration methods, Unit hardware, setting methods, and functions of EtherNet/IP Slave Terminals that consist of an EtherNet/IP Coupler Unit and NX Units.

Terms and Conditions Agreement

Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments.

Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof. Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product.

Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.

2021.3

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/

In the interest of product improvement, specifications are subject to change without notice.

OMRON NX-EIC Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual